How to Test and Slove Problem

8/13/2019 How to Test and Slove Problem

http://slidepdf.com/reader/full/how-to-test-and-slove-problem 1/9

1. from EISU to BTS communicate

1> how to check :

check main communicate flash normal,communicate interrupt,flash time every minute,

communicate normal, flash quickly.

2> how to slove problem.

On the BS !! site,check "# an$ %&',(t shoul$ show about )* + ' ,otherwise S-

boar$ output failure.same you check on the /(S0 site, show about )* + ' too,otherwise /(S0 output failure.

2. ZXDU58 power monitor

1> how to check :

1. On the #'0) site,check "# an$ %&',(t shoul$ show about )* + ' ,otherwise

#'0) S0 output failure.same you check on the /(S0 site, show about )* + ' too

,otherwise /(S0 output failure.

2. open the S0 control panel for #'0 ) , make sure the bau$ rate 3!!, a$$ress: 1



3. Intelligent ar!"rea!er power ca#le an! $ingal ca#le

1> how to check: open the $oor , bell is soun$,4insert car$ ,soun$ close.

2> 5ow to slove problem: use multimeter to test %&' an$ 612v normal,then make sure the

cable contact normal.

%. Smo&e $ingal

1> how to check: blow smoke towar$s it ,/(S0 seventh li7ht show alarm.

2> 5ow to slove problem: 1. first you use multimeter to test %&' an$ 612v normal,make

sure all cable normal ,then contact 612+ an$ smoke ,it shoul$ alarm ,otherwise /(S0

port problem.other you nee$ chan7e the smoke sensor. 'otice( 2 an! 3 lin&.



5. Temp $ingal

1> how to check: blow towar$s it ,/(S0 secon$ly li7ht show alarm.

2> 5ow to slove problem: 1. first you use multimeter to test %&' an$ 6)v normal,makesure all cable normal ,then check %&' an$ '"/ 8 ,it shoul$ more than '

1v,otherwise temp sensor problem.

). D

o

o

r

$ingal

1> 5ow to check: open the $oor ,/(S0 firstly li7ht show alarm,close the $oor ,alarm

$isappear.

2> 5ow to slove problem: 1. first you use multimeter to test %&' an$ 612v normal,make

sure all cable normal ,then contact O an$ & ,alarm $isappear,so you nee$ chan7e

the $oor sensor nearness.otherwise you chan7e the $oor sensor.



*. groun! cut+fen$e

1> 5ow to check: pull out cable ,/(S0 thir$ly li7ht show alarm, contact it ,alarm $isappear.

2> 5ow to slove problem: 1. first you use multimeter to test %&' an$ 612v normal, ,then

check cable no be interrupt .

8. arre$ter an! p,a$e alarm

1> 5ow to check: $isconnection arrestor cable ,/(S0 fourthly li7ht show alarm,

$isconnection phase cable , /(S0 si9th li7ht show alarm.connect all ,alarm $isappear.


check cable no be interrupt.



-. ut!oor Unit of /ir"con!itioner ca#le

1> 5ow to check: $isconnection - cable , ,/(S0 thir$ly li7ht show alarm, contact it,alarm $isappear.


check cable no be interrupt.

10. infrare! /ir"con!itioner control 1 2 31> 5ow to use it: use remote $evice,every air*con$ition operation 2 times; on an$ off,a$<ust

temperature= .

2> 5ow to slove problem: make sure all cable connect normal.



11. /ir"con!itioner 1 2 3 $tatu$ ca#le(

1> 5ow to check: use amperemeter, when - is runnin7,can test current throu7h.

2> 5ow to slove problem: make sure all cable connect normal.

12. /larm ing



1> 5ow to check: open the $oor, -larm soun$,close the $oor,alarm $isappear.or contact

'O - an$ 'O B,alarm soun$.

2> 5ow to slove problem: make sure all cable connect normal. use multimeter to test %&'

an$ 612v normal, otherwise chan7e alarm bell.

13. D fan control an! $tatu$

1> 5ow to check: contact 'O2- an$ 'O2B,fan run.

2> 5ow to slove problem: make sure all cable connect normal. use multimeter to test %&'

an$ 612v normal, otherwise chan7e relay.

1%. /TS $tatu$

1> 5ow to check: $isconnection -"S cable ,/(S0 fourthly li7ht show alarm,connect it

,alarm $isappear.

2> 5ow to slove problem: make sure all cable connect normal. check cable no be interrupt.





6,en $ite for out!oor $ite nee! connect following ca#le(

Documents

How to Test and Slove Problem