Http Www.mutoh.be Binarydata.aspx Type=Doc Rock Hopper e

ROCKHOPPER ECO-SOLVENT PRINTER

OPERATION INSTRUCTIONS

MUTOH EUROPE N.V. Part n°: AP-75024

Rev. 1.2 – 18/08/2002

Operation Instructions Rockhopper Printer

AP-75024 Rev. 1.2. – 18/08/2002

COPYRIGHT NOTICE COPYRIGHT © 2002 Mutoh Europe N.V. All rights reserved. This document may not be reproduced by any means, in whole or in part, without written permission of the copyright owner. This document is furnished to support the Mutoh Rockhopper (48”& 62”) Eco-Solvent Inkjet Printers. In consideration of the furnishing of the information contained in this document, the party to whom it is given assumes its custody and control and agrees to the following: The information herein contained is given in confidence, and any part thereof shall not be copied or reproduced without written consent of Mutoh Europe N.V. This document or the contents herein under no circumstances, shall be used in the manufacture or reproduction of the article shown and the delivery of this document shall not constitute any right or license to do so.


AP-75024 Rev. 1.2. – 18/08/2002


AP-75024 Rev. 1.2. – 18/08/2002

Dear Customer,

Mutoh’s new Rockhopper high-resolution drop-on-demand piezo electric outdoor inkjet printer series consists of two models, i.e. a 62” (157 cm) and a 48” (122 cm) version. Maximum print widths offered are 116 cm for the Rockhopper48 and 155 cm for the Rockhopper62. Application possibilities encompass outdoor poster printing, banners, long-term backlit signage, building and construction announcements, vehicle graphics, durable indoor graphics, POS displays, … The printers use a newly developed eco-solvent ink. Inks are offered in six colours, i.e. cyan, magenta, yellow, black, light cyan & light magenta. Prints are UV- and water-resistant for up to three years outdoors(*). Lamination is required for heavy-duty applications. The Rockhopper printers offer various print resolutions, from 360 dpi & 720 dpi, up to 1440 x 720 dpi and diagonally interpolated 1440 x 1440 dpi. Print speeds vary between 14.49 m²/h at 360 x 180 dpi, 3.6 m²/h at 720 x 720 dpi and 0.68 m²/h at 1440 x 1440 dpi. For the Rockhopper, Mutoh will be offering certified media such as banner and vinyl, optimised for use with the Mutoh Eco-solvent inks. As standard, Mutoh Rockhopper printers are equipped with an automatic take-up system for unattended printing and separately controllable pre and post heaters for instant drying and a wider media compatibility. (*) Accelerated weather tests predict up to 3 years outdoor durability. Outdoor durability is location and application dependant.


AP-75024 Rev. 1.2. – 18/08/2002


AP-75024 Rev. 1.2. – 18/08/2002

TABLE OF CONTENTS

ROCKHOPPER ECO-SOLVENT PRINTER OPERATION INSTRUCTIONS...............................................................................1

Regulatory and Safety Information .......................................................... 9

EMC Statement for CE Marking ...................................................................................9 FCC Compliance ..........................................................................................................9 Safety Labels Safety Labels, Symboles de sécurité, Sicherheitssymbole ..................10

Installation Procedures ........................................................................... 17

Installation requirements: Selecting an adequate place for setting up your Equipment...................................................................................................................................17 Unpacking your Rockhopper printer ...........................................................................19 What’s in the Box?......................................................................................................20 Getting to know the Printer parts and components.....................................................21 Assembling the printer ................................................................................................23 The Parallel interface..................................................................................................29 Tips to use high-speed ECP parallel communication .................................................30 Installation of network interface board ........................................................................31 Connecting the power cable / disconnect device........................................................33

Preparing for a job ................................................................................... 35

Installing the ink cassettes..........................................................................................35 Adjusting Head Height. ...............................................................................................42 Loading media ............................................................................................................43 Using Pre- and post-heaters.......................................................................................55 Using Eco-Solvent Ink ................................................................................................55 Using Pigmented Ink...................................................................................................55 Print Origin Control. ....................................................................................................56 Micro-banding elimination...........................................................................................58

Daily Maintenance.................................................................................... 61

Replacing the ink cassettes ........................................................................................61 Switching between dye inks and pigmented inks or changing to Eco-Solvent Ink. .....62 Cleaning the head cleaning wiper...............................................................................65 Replacing the cutting blade ........................................................................................66 Periodical Maintenance ..............................................................................................68

Understanding the control panel & printer controls............................. 69

Guided tour around the control panel .........................................................................69 Heater System Control Panel. ....................................................................................74 Menu mode operation.................................................................................................75 Print modes accessible via the control panel. .............................................................77


AP-75024 Rev. 1.2. – 18/08/2002

Regulary & Safety Information Operation Instructions Rockhopper Printer

Page 9 AP-75024 Rev. 1.2. – 18/08/2002

REGULATORY AND SAFETY INFORMATION

EMC STATEMENT FOR CE MARKING

Warning: • This is a class A product. In a domestic environment this product may

cause radio interference in which case you may be required to take adequate measures.

FCC COMPLIANCE This equipment complies with the requirements for a Class A computing device in the FCC rules, part 15, subpart J. Operation of this device in a residential area may interfere with television reception or operation of utilities. Printers generate weak radio signals and may interfere with television reception and utilities. If the printer does interfere with radio or TV reception, try the following :

• Change the direction of your radio and TV reception antenna or feeder.

• Change the direction of the printer.

• Move either the printer or the receiving antenna so there is more distance between them.

• Be sure the printer and the receiving antenna are on separate power lines.


Page 10 AP-75024 Rev. 1.2. – 18/08/2002

SAFETY LABELS SAFETY LABELS, SYMBOLES DE SÉCURITÉ, SICHERHEITSSYMBOLE Safety Labels are attached to the internal and external area of the printer to alert you to potentially hazardous situations or conditions. The following safety labels are used in and on the printer: La partie externe et interne de l’imprimante porte des symboles de sécurité destinés à attirer votre attention sur des sources potentielles de danger ou des conditions pouvant être dangereuses. Les symboles de sécurité suivants sont utilisés à l’intérieur et à l’extérieur de l’imprimante: Auf der Innen- und Außenseite des Druckers sind Sicherheitssymbole angebracht, die Sie auf potentielle Gefahrenquellen oder potentiell gefährliche Bedingungen hinweisen sollen. Im und auf dem Drucker werden die nachfolgend aufgeführten Sicherheitssymbole verwendet:

WARNING

♦ Keep fingers clear of opening except when loading media. This may result in unexpected injury and/or poor image quality.

♦ Ne mettez pas le doigts dans l’ouverture sauf lors du montage du papier. Ceci peut éventuellement provoquer des blessures ou avoir un effet néfaste sur l’impression.

♦ Nicht die Finger in die Öffnung stecken, außer wenn Druckmaterial eingesetzt werden muß. Das könnte Verletzungen verursachen und den Druckvorgang beeinträchtigen.

THE OPENING / OUVERTURE / ÖFFNUNG

CAUTION

♦ When the message “Clean the wiper” is appeared on the LCD of the operation panel, clean up the Head Cleaning Wiper. Refer to the User Guide in detail.

♦ Periodical cleaning can avoid bad print result.

♦ Lorsque le message “Nettoyer le balai” apparaît sur l’ecran LCD du panneau de commande, nettoyer le balai de nettoyage de la tête. Reportez-vous au guide de l’utilisateur pour les détails.

♦ Le nettoyage périodique peut éviter la dégradation de la qualité de l’impression.

♦ Wenn die Meldung “Wischer reinigen” auf dem LCD an der Frontplatte erscheint, den Kopfwisser reinigen. Nähere Einzelheiten siehe Bedienungsanleitung.

♦ Periodische Reinigung kann schlechte Druckqualität verhindern.


Page 11 AP-75024 Rev. 1.2. – 18/08/2002

CAUTION

♦ The corner edge of the Cutter Guide is sharp. Be careful not to cut your fingers.

♦ The edge of the cutting tool such as knife is very sharp. When cutting roll media with knife manually, handle it with care.

♦ Le bord d’angle du guide du cutter est tranchant. Veillez à ne pas vous couper les doigts.

♦ Le bord des outils de coupe comme un couteau est très tranchant. Manipulez ces outils avec précaution si vous coupez le rouleau de papier manuellement au couteau.

♦ Die Eckkante der Schneidevorrichtungsführung ist scharf. Es besteht Verletzunsgefahr.

♦ Scheidwerkzeuge wie Messer sind sehr scharf. Beim Schneiden von Rollenmaterial von Hand mit einem Messer vorsichtig vorgehen.

CAUTION

♦ Do not open the front cover or touch the media during printing. This will result in poor image quality.

♦ If no printing is to be done for some time, remove the media and set the hold lever in the up position. Otherwise the media may lift up or become wrinckled and you will not be able to obtain good printing results.

♦ Ne pas ouvrir le couvercle avant pendant l’impression. Et ne touchez pas le papier pendant l’impression pour éviter que la qualité d’impression ne se dégrade.

♦ Si vous ne comptez pas imprimer pendant un certain temps, retirez le papier et mettez le levier en position levée. Sinon, le support risque de se soulever et de se froisser et vous ne pourrez pas obtenir une bonne qualité d’impression.

♦ Wahrend des Druckens nicht die Frontabdeckung öffnen und nicht das Druckmaterial berühren. Das kann das Druckergebnis beeinträchtigen.

♦ Wenn längere Zeit nicht gedruckt werden soll, das Druckmaterial herausnehmen und die Haltehebel in die obere Position stellen. Anderenfalls kann sich das Druckmaterial heben oder falten, so daß keine guten Druckergebnisse mehr zu erzielen sind.

CAUTION If the media feed is not operating properly the media will jam and you will not be able to obtain good printing results. ♦ Don't use media that is curled, creased or torn. ♦ The media must be mounted correctly ♦ Media should be acclimatized to the environment for about 30 minutes before it is used. ♦ When roll media is mounted, the selector on the front panel must be set to roll media. If cut media is selected

when roll media is mounted, about 3m of media will be fed.

Si l'alimentation de papier ne fonctionne pas normalement, des bourrages risquent de se produire et vous ne pourrez pas obtenir une bonne qualité d'impression. ♦ Ne pas utiliser de papier recourbé, plissé ou déchiré. ♦ Le papier doit être chargé correctement. ♦ Le papier devra être acclimaté à l'environnement pendant environ 30 minutes avant d'être utilisé. ♦ Lorsque le rouleau de papier est chargé, le sélecteur du panneau frontal doit être réglé sur "Papier en rouleau".

Si, "Papier coupé" est sélectionné alors qu'un rouleau de papier est chargé, 3m de papier environ seront alimentés.

Wenn das Druckmaterial nicht einwandfrei transportiert wird, staut es sich, und es können keine guten Druckergebnisse erzielt werden. ♦ Keine gerolltes,geknittertes oder eingerissenes Druckmaterial verwenden. ♦ Das Druckmaterial muß korrekt eingesetzt werden. ♦ Das Druckmaterial sollte vor Gebrauch etwa zehn Minuten lang der Betriebsumgebung angepaßt werden. ♦ Beim Einsetzen von Rollenmaterial muß der Wahlschalter an der Frontplatte auf Rollenmaterial eingestelt

werden. Steht der Wahlschalter auf Einzelblattmaterial, wenn Rollenmaterial eingesetzt ist, werden etwa 3m Druckmaterial zugeführt.


Page 12 AP-75024 Rev. 1.2. – 18/08/2002

CAUTION

Precautions when the hold lever is up. ♦ Don't put the hold lever up while the head is operating (printing, media size detection,cutting,etc..)

The head and media keeper blade may touch, causing damage and poor image quality. ♦ When the lever is up for media mounting, etc…, make sure the head is in a position where it does not

come into contact with the media keeper blade. ♦ Don't move the head while the lever is up. The media keeper blade must not come into contact with the

head. Precautions when replacing the cutter. ♦ The power supply must be switched off and the hold lever must be in the down position when the cutter is

being replaced.

Précautions lorsque le levier de maintien est levé. ♦ Ne pas lever le levier de maintien lorsque la tête fonctionne (pendant l'impression, la selection du support

d'impression, la coupe du papier, le nettoyage, etc..). La tête et la lame de maintien du papier peuvent entrer en contact et provoquer des dommages ou nuire à la qualité de l'image.

♦ Lorsque le levier est levé pour monter le support ou autres, veillez à ce que la tête soit dans une postion où elle n'entre pas en contact avec la lame de maintien du support.

♦ Ne pas déplacer la tête lorsque le levier est levé. La lame de maintien du support ne doit pas entrer en contact avec la tête.

Précautions lors du remplacement du cutter. ♦ Mettre l'appareil hors tension et abaisser le levier de maintien pendant le remplacement du cutter.

Vorsichtsmaßnahmen bei hochgestelltem Haltehebel. ♦ Den Haltehebel nicht hochstellen, während der Kopf arbeitet (beim Drucken, bei der Erkennung der

Druckmaterialgröße, beim Schneiden des Druckmaterials, bei der Reinigung, usw..). Der Kopf und das Druckmaterial-Haltemesser könnten sich dabei berühren und Beschädigungen oder schlechte Bildqualität verursachen.

♦ Wenn der Hebel zum Einsetzen von Druckmaterial usw. Hochgestellt ist, ist darauf zu achten, daß er sich nicht in einer Position befindet, in der er in Kontakt mit dem Druckmaterial-Haltemesser kommt.

♦ Den Kopf nicht bewegen, während der Hebel hochgestellt ist. Das Druckmaterial-Haltemesser darf nicht in Kontakt mit dem Kopf kommen.

Vorsichtsmaßnahmen beim Auswechseln der Schneidevorichtung. ♦ Beim Auswechseln der Schneidevorrichtung muß die Stromversorgung ausgeschaltet sein und der

Haltebhebel muß sich in der unteren Position befinden.

WARNING

♦ The edges of the steel belt are sharp and should not be touched.

♦ Les bords de la courroie métallique sont tranchants et ne doivent pas être touchés.

♦ Die Kanten des Stahlriemens sind scharf und sollten nicht berürht werden.

CAUTION

♦ The pressure roller must be in the up position whenever it is to be moved.

♦ Le rouleau de pression doit être mis en position levée lorsqu'il doit être déplacé.

♦ Die Andruckrolle muß sich zum Verschieben in der oberen Position befinden.


Page 13 AP-75024 Rev. 1.2. – 18/08/2002

CAUTION

♦ The cutter blade is a consumable item. When its cutting performance deteriorates it should be replaced in accordance with the User Manual.

♦ The media sensor section and printing board should be cleaned regurarly as detailed under daily maintenance in the User Manual.

♦ La lame du cutter est un article consommable qui doit être remplacé conformément à la procédure indiquée dans le mode d'emploi lorsque les performances de coupe se dégradent.

♦ La section de détection du support et la carte de traçage doivent être nettoyés périodiquement de la manière indiquée pour l'entretien journalier dans le mode d'emploi.

♦ Die Schneidevorichtung ist ein Verbrauchsartikel. Wenn ihre Schneideleistung nachlaßt, muß sie entsprechend den Anweisungen in der Bedienungsanleitung ausgewechselt werden.

♦ Der Bereich des Druckmaterialsensors und die Zeichenfläche sollten regelmäßig gereinigt werden, wie unter tâgliche Wartung in der Bedienungsanleitung beschrieben.

MOUNTING CUT MEDIA

♦ Pass the media between the media keeper blade and the printing board.

♦ Align the front right corner of the media with the edge of the paper guide.

♦ Align the right side of the media with the center of the alignment line (hole).

♦ Passez le papier entre la lame de maintien et le carte d’impression.

♦ Alignez le coin avant droit du papier avec le bord du guide de papier.

♦ Alignez l’extrémité droite du papier sur le centre de la ligne d’alignement (orifice).

♦ Das Druckmaterial zwischen dem Druckmaterial-Haltemesser und der Zeichenfläche hindurchführen.

♦ Die vordere rechte Ecke des Druckmaterials auf die Kante der Papierführung ausrichten.

♦ Die rechte Seite des Druckmaterials auf die Mitte der Ausrichtungslinie (Loch) ausrichten.


Page 14 AP-75024 Rev. 1.2. – 18/08/2002

LOADING ROLL MEDIA

1. Remove the tape from the roll media and pull out a rather long length of roll media.

1. Retirez la bande du rouleau et tirez une bonne longueur de papier.

1. Das Klebeband von der Rolle abziehlen und ein ziemlich langes Stück Rollenmaterial herausziehen.

2. Insert the end of the roll media between the pressure roller and the drive roller and pull out a fairly long length of roll media.

2. Introduisez l’extrémité du papier en rouleau entre le rouleau de pression et le rouleau d’entraînement et tirez une bonne longueur de papier.

2. Das Ende des Rollenmaterials zwischen der Andruckrolle und der Antriebsrolle einsetzen und ein ziemlich langes Stück Rollenmaterial herausziehen.

CHECK THE POSITION OF THE ROLL MEDIA Rotate the scroller by hand, taking several turns of roll media and check the position of the roll media. The position is correct if the right side of the roll media is in the center of the alignment line (hole)

Faites tourner la couronne de la main pour faire plusieurs tours au rouleau de papier et vérifiez la position du rouleau. Elle est normale si l’extrémité de droite du rouleau se trouve à l’extrémité de droite du rouleau d’entraînement et au centre de la ligne d’alignement (orifice).

Durch mehrmaliges manuelles Drehen der Papierspindel Rollenmaterial vor transportieren und seine Position prüen. Das Rollenmaterial hat die richtige Position wenn sich seine rechte Seite am rechten Ende der Antriebsrolle und in der Mitte der Ausrichtungslinie (Loch) befindet.


Page 15 AP-75024 Rev. 1.2. – 18/08/2002

ADJUSTING ROLL MEDIA POSITION

If the position of the roll media is incorrect, adjust the position of the roll media as shown in the diagram below.

Si la position du rouleau est incorrecte, réglez-la de la manière indiquée sur le schéma ci-dessous.

Wenn sich das Rollenmaterial nicht in der richtigen Position befindet, muß es wie in der Abbildung unten gezeigt justiert werden.

If the roll needs to be moved to the right.

Si le rouleau de papier doit être retiré vers le côté droit.

Wenn das Rollenmaterial nach rechts verschoben werden muß.

If the roll needs to be moved to the left.

Si le rouleau de papier doit être retiré vers le côté gauche.

Wenn das Rollenmaterial nach links verschoben werden muß.

CAUTION ♦ Ink cartridges must not be removed during printing or poor image quality will result. ♦ Keep fingers clear of the ink cartridge box. It contains projecting parts which may cause

you an unexpected injury ♦ When removing or inserting the waste fluid box, be careful not to tilt it. You may spill ink

on your clothing and the equipment.

♦ La cartouche d’encre ne doit pas être retirée pendant l’impression, ceci pouvant affecter sérieusement la qualité de l’impression.

♦ Ne pas mettre les doigts à l’intérieur du carton de la cartouche d’encre. Il contient des pièces protubérantes qui pourrait vous blesser par inadvertance.

♦ Veillez à ne pas incliner le cartes d’encre usagée lors de son retrait ou de sa mise en place. Vous risquez de vous salir ou de salir les appareils si vous renversez de l’encre

♦ Die Tintenpatrone darf während des Druckens nicht entfernt werden. Das könnte den Druckvorgang erheblich beeinträchtigen.

♦ Nicht die Finger in den Tintenpatronenbehälter stecken. Dieser enthält vorstehende Teile die Verletzungen verursachen können.

♦ Den Alttintenbehälter beim Herausnehmen und Einsetzen nicht neigen. Dabei könten Alttinte herauslaufen und Kleidung und Gerät beschmutzen.


Page 16 AP-75024 Rev. 1.2. – 18/08/2002

Installation Procedures Operation Instructions Rockhopper Printer

Page 17 AP-75024 Rev. 1.2. – 18/08/2002

INSTALLATION PROCEDURES

Warning: Make sure to connect the power cable only after all the steps of the installation procedure are completed.

INSTALLATION REQUIREMENTS: SELECTING AN ADEQUATE PLACE FOR SETTING UP YOUR EQUIPMENT

The location where you set up your equipment is very important. Please see to it that it meets following conditions:

♦ Power supply: - Voltage: 200 to 240 VAC or 100 to 120 VAC - Frequency: 50/60 Hz ± 1 Hz - Current: < 10 A (110 V)

< 5 A (220 V)

♦ Ambient conditions: • Operating environment

- Temperature: 10°C to 35°C - Humidity: 20% - 80% non-condensing

• Storage environment - Temperature: -10°C to 60°C - Humidity: 20% - 90% non-condensing

• Variation rate - Temperature: 2°C per hour - Humidity: 5% per hour

♦ Do not connect the printer to a power supply used by other devices that could interfere with your printer.

♦ Do not use thinner, benzene or similar agents on the printer.

♦ Only use original Mutoh ink cassettes. Use of different ink cassettes might cause damage to your printer. When using non Mutoh ink cassettes, the ink supply system, the heads as well as the cleaning system will be considered out of warranty.

♦ Keep ink cassettes out of the reach of children.

♦ Store your ink cassettes in a cool place. The Rockhopper ink could get frozen, however, if you store your ink below -18°C. In this case, leave your cassettes at room temperature for at least three hours before using them.


Page 18 AP-75024 Rev. 1.2. – 18/08/2002

♦ Protect your printer from moisture, dust, draughts and direct sunlight. ♦ It is best to keep your machine away from open windows and air-conditioners.

♦ See to it that there is an adequate space around the printer so that ventilation is not obstructed.

♦ Avoid using your Rockhopper printer near heating systems, such as stoves or heaters.

♦ Avoid using your printer under strong lighting, such as halogen lamps or light bulbs.

♦ When selecting a place for your printer, leave at least 1 m in front and at the sides, and 1 m at the rear.


Page 19 AP-75024 Rev. 1.2. – 18/08/2002

UNPACKING YOUR ROCKHOPPER PRINTER The printer body and printer Take-up system are packed in two separate boxes. Unpack the printer body first.

Caution: • When unpacking the printer, check whether all parts described in the

parts list are included in the box. Consult your dealer if anything seems to be missing.

• Lifting the machine out of the box should be done by four people.

• Protect the printer from shocks.

• Do not dismantle the unit.

Procedure for unpacking the printer: Step 1: Remove the top cover cardboard and big sleeve. Step 2: Take out the leg set, accessories box, extra media scroller, beams,…

Step 3: Open the printer body box. Step 4: Remove all plastic and cardboard pieces holding the printer body. Step 5: Take out your media scroller Step 6: Check whether all parts described in the parts list are included in the box. Consult your dealer if anything seems to be missing.


Page 20 AP-75024 Rev. 1.2. – 18/08/2002

WHAT’S IN THE BOX?

What’s in the box ?

• Rockhopper printer unit • Printer stand

• 2 media scrollers (2” / 3”) including plastic flanges

• Scroller Slip Ring • 1 Sheet-off knife, pre-installed in head • Onyx PosterShop™ Lite – Mutoh Edition

Accessories kit consisting of: • Power cable • User’s Guide

• Extra Box with Roll Take-Up System


Page 21 AP-75024 Rev. 1.2. – 18/08/2002

GETTING TO KNOW THE PRINTER PARTS AND COMPONENTS

Left Cover

Front Paper Guide

Front Cover Y-rail Cover Operating Panel Right Cover

Heater Panel

Pressure Lever

Waste Bottle

Control Box Take-up System

Left Cover

Front Paper Guide

Front Cover Y-rail Cover Operating Panel Right Cover

Heater Panel

Pressure Lever

Waste Bottle

Control Box Take-up System

Cartridge Cover 6 Ink Slots

Rear Paper Guide

Scroller

Waste Bottle

Scroller Adjusting Screw

Scroller Slip Ring


Page 22 AP-75024 Rev. 1.2. – 18/08/2002

Part Description

Covers The protective covers protect the action environment. Opening a cover immediately pauses printing which resumes when the cover is closed.

Operation Panel Positive Touch keyboard with integrated LCD-Display.

Heater Panel To control the pre- and post heaters with integrated LCD-Display.

Pressure Lever Lowers / Releases pressure rolls to load / unload media.

Take-up system Used when using roll media.

Control box Box with the main electrical components..

Front Paper Guide The print plate is a firm, flat base which supports the media during printing and houses the vacuum system and post-heaters.

Rear Paper Guide Support the media during printing and houses the pre-heaters.

Scroller Feeds through the roll media core to hold the media.

Scroller adjusting screw

To adjust the position of the roll media.

Scroller Slip Ring Prevents unwinding of roll media.

Ink cassette slots Hold / detect the ink cassettes which are in use.

Waste bottle Collects inkflow resulting from: purging, cleaning.

Caution: • Do not use the printer as a shelf to store equipment. • Do not lean on Front Paper Guide, Cartridges, … This may result in

unrecoverable damage of your machine.


Page 23 AP-75024 Rev. 1.2. – 18/08/2002

ASSEMBLING THE PRINTER

Caution: • Before lifting the printer body out of the box, make sure to remove all

plastic wrapping materials first, in order to avoid that the machine slips from your hands.

Step 1: Unpack the stand and assemble it by screwing the left and right stand legs to the cross beam (upper bar)(1) and to the cross bar (lower bar)(2). To do this, use the 4 long hexagon bolts and the large hex wrench provided to secure the cross beam (1), and 2 long hexagon bolts to secure the cross bar (2). Make sure the caster wheels are on the front. After securing the bolts permanently, put on the two plastic side covers.

Step 2 : First make sure to mount the left end plate (plate without motor box) to the left leg of the stand.


Page 24 AP-75024 Rev. 1.2. – 18/08/2002

Hook the left end plate between the leg assembly. Turn the left end plate diagonally, so that you can put it in-between the left leg and then turn it right to fix it into place by means of the hooks.

Fasten the left end plate temporarily with 2 bolts + washers (use a 3 mm hex key) onto the bracket.

Push the endplate as much as possible to the upper side of the leg assembly, so you can easily screw the printer body onto the stand.


Page 25 AP-75024 Rev. 1.2. – 18/08/2002

Step 3 : Hook the right end plate between the leg assembly. To do so, follow the same procedure as for the left end plate. Hook the right end plate between the leg assembly. Turn the right end plate diagonally, so that you can put it in-between the right leg and then turn it right to fix it into place by means of the hooks.

Fasten the right end plate temporarily with 2 bolts + washers (use a 3 mm hex key) onto the bracket.

Push the endplate as much as possible to the upper side of the leg assembly, so you can easily screw the printer body onto the stand.


Page 26 AP-75024 Rev. 1.2. – 18/08/2002

Step 4:

Caution: • For safety, at least four people are needed for assembling the printer. • When taking the main unit out of the carton, remove the vinyl first and

handle the printer directly. There is a risk of your hands slipping if the main unit is handled with the vinyl on.

• The main unit must be lifted by four people at the places marked (1) to (8) below. If it is lifted at other places (left and right side covers, ink cartridge cover, etc.) the printer may fall and cause injury or damage.

Fix the printer body onto the leg assembly using the two wing screws. As mentioned in step 2 & 3 the end plates should be pulled as much as possible towards the upper part of the stand. To do so, loosen a little bit the bolts temporarily fixing the endplates with a hex key of 3 mm and make sure that they are pulled as much as possible towards the stand. Now you can fix both wing screws firmly. Once the wing screws are fastened, you can secure the bolts on the endplates (see step 2 & 3) firmly with the hex key.


Page 27 AP-75024 Rev. 1.2. – 18/08/2002

Step 5 : The sensor assembly should be mounted on the right side of the stand. Take the sensor bracket and put it through the outer slothole of the sensor assy.

Now you can fix the sensor assy.

Fix the sensor assembly smoothly to the motor box, using 2 bolt + washers (use upper holes) (detail A). Hook the sensor bracket over the leg and secure it with a bolt + washer (detail B).


Page 28 AP-75024 Rev. 1.2. – 18/08/2002

Step 6: Loosen the wing screw which is fixed to the printing table (4) and remove the metal fixing plate (5), which blocks the printer head during transportation. (See 4 & 5 on figure below). Keep the metal fixing plate and wing screw, since the printing head needs to be blocked during any transportation of your printer.

Caution: • Take care not to drop the wing screw inside the printer body. Should

it fall in, do not boot up your printer until the wing screw has been safely removed.

Remove the tape that locks the sheet-off mechanism during transportation (See 6 on figure below).

Step 7: Remove the cable block(s) between rail and cover (7).

Remove the lever block (8).

Step 8 : Install the Waste Bottle (2 screws). Do not forget to connect the connector and the waste tubes. Step 9: After setting up the printer, wheel it to the desired location and lock the caster wheels.


Page 29 AP-75024 Rev. 1.2. – 18/08/2002

THE PARALLEL INTERFACE

Caution: • When connecting the printer to your computer, make sure that both

your printer and your computer are switched OFF.

Note: • For optimum output, please use a cable recommended by Mutoh.

The printer can use the Centronics interface (IEEE1284 compatible, Nibble, ECP). Connect to the printer as shown in the following diagram with an interface cable (option) for the connection system you will use. Connect to the host computer with another interface cable.

Note: • The use of an unnecessary long cable may influence your data

transmission. Therefore, keep your interface cable as short as possible.

• An Ethernet board RJ-ETH14TX (for networking) is available as an optional extra.


Page 30 AP-75024 Rev. 1.2. – 18/08/2002

TIPS TO USE HIGH-SPEED ECP PARALLEL COMMUNICATION

• If the parallel port setting on the printer is set to BI CENTRO (See Menu Mode Operation – Menu Structure Overview) your printer is ready for high-speed bi-directional communication.

• In order to be able to use this high-speed mode without problems please note: • Computer Bios for parallel port should be set to ECP • Only use a shielded and balanced parallel cable, which is IEEE 1284 compliant. • If your RIP software is protected with a hardware lock (dongle), which needs to be

placed on the parallel port, it is best to have available 2 parallel ports. – One port to connect: hardware lock, scanner, external drive or CD-ROM,… – One port (ECP) directly connected to the printer.

In case either of the above mentioned topics is not respected you may encounter all kinds of printer artifacts such as: unexplainable error messages, sheet-off during printing, unexpected media feed during printing, etc… If this occurs, switch your system to unidirectional parallel communication. – Set print parallel port to Mode > CENTRO – Set computer parallel port Bios to SPP or EPP

The data transfer will then slow down and the artifacts will disappear. Before switching back to the high-speed bi-directional parallel mode, have your computer system examined closely by a trained computer technician.


Page 31 AP-75024 Rev. 1.2. – 18/08/2002

INSTALLATION OF NETWORK INTERFACE BOARD The standard interface for the Rockhopper printer has a parallel Centronics compatible interface as standard equipment. The network interface board, RJ-ETH14TX, for connection to EtherNet is also available as an option. The following procedure explains how to install the network interface board.

Caution: • When installing the Network interface board, make sure that the

Rockhopper printer is switched off and the power cable is disconnected.

To install the network card proceed as follows: Step 1 :

Loosen the two screws, which are fixed to the interface cover plate on the left side of the Board box below the printer and remove the plate.

1. Interface cover plate 2. Board box

Step 2 :

Insert the optional interface board into the slot as shown in the diagram. When the interface board has reached the back, push it again to ensure it is pushed fully back.

1. Interface board

Caution: • Electronic components are susceptible to damage by static

electricity. Remove static charge from your clothes and body by touching your hands to the board box before you touch the network interface board.

Step 3 : Fasten the two interface mounting screws.


Page 32 AP-75024 Rev. 1.2. – 18/08/2002

Step 4 :

Connect a Category 5 EtherNet cable compatible with both 10BASE-T and 100BASE-TX to the connector on the interface board. Connect the other end of the Ethernet cable to the 10BASE-T or 100BASE-TX network hub.

10BASE-T/100BASE-TX Compatible Ethernet Cable (Category 5)


Page 33 AP-75024 Rev. 1.2. – 18/08/2002

CONNECTING THE POWER CABLE / DISCONNECT DEVICE

1) Make sure the printer’s power switch is turned OFF.

2) Make sure the power of the Heating System and the Roll Take-Up System are turned OFF.

3) Plug the printer-end of the power cable into the connector at the back of the printer.

4) Connect the cable of the Roll-Take-Up System with the Printer body.

5) Plug the other end of the power cable into an electrical outlet of the correct voltage and with a proper grounding.

• Power supply: - Voltage: 200 to 240 VAC or 100 to 120 VAC - Frequency: 50/60 Hz ± 1 Hz - Current: < 10 A (110 V)

< 5 A (220 V)

Note: • When you turn off the power, please note that your printer needs a

few seconds to perform its shut down sequence. • To this end, wait for at least five seconds to switch the printer on

again.

• The disconnect device is the plug on the power supply cord.


Page 34 AP-75024 Rev. 1.2. – 18/08/2002

Preparing for a job Operation Instructions Rockhopper Printer

Page 35 AP-75024 Rev. 1.2. – 18/08/2002

PREPARING FOR A JOB

INSTALLING THE INK CASSETTES PRECAUTIONS WHEN USING INK CASSETTES : Please read below recommendations carefully before you start using your Rockhopper ink cassettes.

Caution:

• It is recommended to avoid any direct contact with the inks. If you come in close contact with the inks, please pay attention to the following first-aid measures: Eye contact: Rinse out the ink with a large quantity of water and consult your doctor. Skin contact: Wash off the ink with soap and water. Ingestion: Rinse your mouth immediately, drink a large quantity of water or milk and consult your doctor.

• Keep the ink cassettes out of the reach of children.

• The ink cassettes are inflammable (ignition point 63°C). Avoid contact with heating sources and any sort of ignition source.

Important: • If you use your Rockhopper printer for the first time, you need to

install 6 cassettes in the slot, which is located at the back of the printer.

• Before using Eco-Solvent ink, perform a head wash. Tubes, heads and filters must be clean. Use the special Eco-solvent Transition Liquid.

• Once you have worked with eco-solvent inks, it is forbidden to change to another ink type.

• Do not use other ink cassettes but the exclusive Mutoh Rockhopper ink cassettes. When using non Mutoh ink cassettes, the ink supply system, the heads as well as the cleaning system will be considered out of warranty if damage occurs. Also see to it that you install your cassettes in the correct way. Use of incorrectly coded cassettes may cause printer damage.


Page 36 AP-75024 Rev. 1.2. – 18/08/2002

Notes: • Unpack the ink cassettes just before installing them in the slot. If you

leave your cassettes open for a long time, they may cause blurred plots.

• After installing the ink cassettes, do not take them out until you replace them.

• The ink cassettes have to be used within two years from the date printed on the cassette. Ink cassettes, which are installed in the printer, should be used up in six months.

• Moving ink cassettes from a cold place to a warm place may cause condensation. Always leave the cassettes at room temperature for more than three hours before using them.

• If the head is stopped during a print cycle, it may leak. To this end, never turn the power off nor unplug the power cable during printing or while the printing head moves.

• In case of a power failure during printing, switch off the printer and manually move the head to the right until you feel that it drops into the capping position.

• In case a power failure occurs when you are absent, the printer will move the head to the capping position when power is restored and a cleaning cycle will take place automatically.

INSTALLING THE INK CASSETTES IN A MUTOH ROCKHOPPER :

Important: • Before using Eco-Solvent ink, perform a head wash. Tubes, heads

and filters must be clean. Use the special Eco-solvent Transition Liquid.

• Once you have worked with eco-solvent inks, it is forbidden to change to another ink type.

A. Going to use Eco-Solvent ink. If you are going to use Eco-Solvent ink, please perform a head wash. Use the special Eco-Solvent Transition Liquid. If you are not going to use Eco-Solvent ink, but Dye or Pigmented Ink, go to point “B. Installing Ink Cassettes”. Step 1: The power switch is located at the right side of the printer, below the printer body. Turn the switch ON and put the hold lever in the DOWN position.


Page 37 AP-75024 Rev. 1.2. – 18/08/2002

Step 2: The printer starts up its initialization routine and the printer display shows the following message: Y: Yellow M: Magenta C: Cyan K: Black O: Orange or Light Cyan G: Green or Light Magenta

Note : • If the cover is open or the hold lever is up, the initialization routine will

not start.

Step 3 : Slide the 6 Eco-Solvent Transition Liquid cleaning cassettes into their cartridge

position. (Automatic detection of cleaning cassettes occurs due to label recognition)

Step 4 : Check if the Waste Bottle if empty. Confirm replacement of the waste box. Step 5 : Following message will appear :

Press the [VALUE/+] or [VALUE/-] key to select “Yes” and press ENTER. Step 6 : The cleaning period is approximately 10 minutes. Step 7 : Remove the cleaning cassettes after ending the cleaning cycle.

Wash Black & Colour?

[Y M C K O G] No cartridge


Page 38 AP-75024 Rev. 1.2. – 18/08/2002

Step 8: Insert 6 ink Eco-Solvent cassettes one by one, respecting the order shown in the illustration below.

• Ink cassette slots 1 to 4 respectively destined for Black, Cyan, Magenta and Yellow are coded so that the ink cassettes cannot be malpositioned.

• Slots 5 and 6 however are NOT CODED. Please check carefully not to put the ink cassettes into an incorrect slot. All RIP software drivers developed according to Mutoh guidelines require: Slot 5 to contain: Light Cyan or Orange Slot 6 (leftmost slot) to contain: Light Magenta or Green

• Only in very special applications it might be needed to introduce the cassettes using another order. In this case carefully follow the instructions given in the application software user guide.

Step 9: After having installed the ink cassettes, the printer will display the following message: Step 10: After this message, automatic ink replenishment begins. The “ink refill” message means that ink is being filled into the ink supply system (tubing + head). The printer is now ready to print.

Caution: • During ink replenishment, never cut off the electricity. This may cause

damage to your printer. • In case of a power failure during ink replenishment, proceed as

follows: 1. Switch off the unit (Power Switch) and check to restore the power. 2. Switch on the unit and check that it gives no error messages in the

display. 3. Perform a cleaning cycle and check the test plots. 4. Repeat step 3 until plot quality is acceptable.

User no media

Ink Refill rest 1 M


Page 39 AP-75024 Rev. 1.2. – 18/08/2002

Note: • In case the ink cassettes are installed and the display message “NO

CARTRIDGE” still appears, this means that the ink cassettes are not inserted correctly. Pull out the cassette(s) indicated and try to insert it (them) correctly.

• In case of failure of initial ink replenishment, apply head cleaning a couple of times. If the ink replenish does not commence after several head cleaning cycles, contact your dealer.

• If the display shows “not original ink” please contact your ink supplier and make sure to get original Mutoh Rockhopper ink.

B. Installing Ink Cassettes. Step 1: The power switch is located at the right side of the printer, below the printer body. Turn the switch ON and put the hold lever in the DOWN position.

Step 2: The printer starts up its initialization routine and the printer display shows the following message: Y: Yellow M: Magenta C: Cyan K: Black O: Orange or Light Cyan G: Green or Light Magenta

Note : • If the cover is open or the hold lever is up, the initialization routine will

not start.

Step 3: Insert 6 ink cassettes one by one, respecting the order shown in the illustration below.

[Y M C K O G] No cartridge


Page 40 AP-75024 Rev. 1.2. – 18/08/2002

• Ink cassette slots 1 to 4 respectively destined for Black, Cyan, Magenta and Yellow are coded so that the ink cassettes cannot be malpositioned.

• Slots 5 and 6 however are NOT CODED. Please check carefully not to put the ink cassettes into an incorrect slot. All RIP software drivers developed according to Mutoh guidelines require: Slot 5 to contain: Light Cyan or Orange Slot 6 (leftmost slot) to contain: Light Magenta or Green

• Only in very special applications it might be needed to introduce the cassettes using another order. In this case carefully follow the instructions given in the application software user guide.

Step 4: After having installed the ink cassettes, the printer will display the following message: Step 5: After this message, automatic ink replenishment begins. The “ink refill” message means that ink is being filled into the ink supply system (tubing + head). The printer is now ready to print.

Caution: • During ink replenishment, never cut off the electricity. This may cause

damage to your printer.

• In case of a power failure during ink replenishment, proceed as follows:

1. Switch off the unit (Power Switch) and check to restore the power. 2. Switch on the unit and check that it gives no error messages in the

display. 3. Perform a cleaning cycle and check the test plots. 4. Repeat step 3 until plot quality is acceptable.

User no media

Ink Refill rest 1 M


Page 41 AP-75024 Rev. 1.2. – 18/08/2002

Note: • In case the ink cassettes are installed and the display message “NO

CARTRIDGE” still appears, this means that the ink cassettes are not inserted correctly. Pull out the cassette(s) indicated and try to insert it (them) correctly.

• In case of failure of initial ink replenishment, apply head cleaning a couple of times. If the ink replenish does not commence after several head cleaning cycles, contact your dealer.

• If the display shows “not original ink” please contact your ink supplier and make sure to get original Mutoh Rockhopper ink.


Page 42 AP-75024 Rev. 1.2. – 18/08/2002

ADJUSTING HEAD HEIGHT. Depending on the media type and media thickness used, it is possible to adjust the printer’s printhead height accordingly 1.5 mm to 2.0 mm (± 0.15 mm).

The head height can be adjusted using the lever on the left side of the head (please refer to the picture mentioned above). When the lever is put in horizontal position (turn counter clockwise) the head is in his highest position : 2.0 mm When the lever is turned clockwise, the head is in his lowest position : 1.5 mm. The lever can only be put in two positions, there are no intermediates. Typical use :

LOW HIGH Photo quality output on photo paper type media (Mutoh Photo Great Piezo Media, Paper, Vinyl, Synthetic paper,…)

Thick media or media with fibres (Fabrics) which may touch the printhead during printing. (Canvas, Art Paper, Cardboard,…)


Page 43 AP-75024 Rev. 1.2. – 18/08/2002

LOADING MEDIA

1. GENERAL RECOMMENDATIONS WITH REGARD TO PRINTER MEDIA

Important: • Do not use media that is creased, blemished, torn or curled. • Problems caused by using media other than that specified by Mutoh

will not be covered by warranty. Always use cut media or roll media specified by Mutoh.

• Temperature and humidity suitable for printing are shown below. We recommend setting up in an environment that can be air conditioned in order to maintain constant temperature and humidity. Temperature 10°C to 35°C (16°C to 25°C for assured printing

accuracy) Variation rate: Not more than 2°C per hour.

Humidity 35% to 80% (50% to 60% for assured printing accuracy) with no condensation. Variation rate: Not more than 5% per hour.

• The absolute dimensions of printing media will be changed by variations in temperature and humidity. Therefore, printing media such as tracing media and high quality media that are readily susceptible to the effects of environment changes should be acclimatized to the environment for about 30 minutes before printing. This acclimatization is called seasoning. Inadequate seasoning may cause the printing media to slip, crease or jam. It also affects the printing quality.

• With media recommended by Mutoh, you should be aware that a 1% variation in humidity may cause the media to expand or contract by the proportions shown below.

Type of media Rate of dimension change Good quality media 0.018% Double-matte polyester film 0.0012%

• Oil from your skin may interfere with the way the ink sits on the media so you should wash your hands thoroughly before handling the media.

• If media that is larger than the prescribed size is used, the result of the printing may be affected by the media touching the floor during printing.

• Do not leave media loaded in the printer for a long period. This may cause media to curl, lift up or jam. (This should be avoided especially in winter, dry periods and for formal printed outputs.)

• Media has a printing surface and non-printing surface. Printing on the non-printing surface may cause blurring or blemishes.


Page 44 AP-75024 Rev. 1.2. – 18/08/2002

2. LOADING ROLL MEDIA Step 1: Open the cover, check that the head is in a position where it will not touch the media keeper blade and put the hold lever up. Step 2: Selecting the media

• Press the [Media] key to select between cut-sheet or roll media.

• By pressing the key you will see the LED alternate between the two choices. Now select roll.

Note : When making the wrong choice by selecting cut-sheet when a roll is loaded, the printer will pull off the maximum cut-sheet length, searching the back edge. Finally the printer will report a media search error.

Step 3: Take your roll of media. Step 4: Remove the movable flange from the scroller by pulling it off.

Step 5: Load the media over the scroller Turn the roll media as shown in the diagram and pass it over the scroller until the media tube fits firmly over the fixed flange. Replace the movable flange on the scroller and fit it firmly into the media tube.


Page 45 AP-75024 Rev. 1.2. – 18/08/2002

Note: • Do not drop the media roll over the scroller as this might damage the

scroller end caps. • All Mutoh recommended roll media are rolled up with the printable

side facing the outside, so that you can load the roll media easily. • When the cut sheet indicator light is ON when loading a roll, the

printer will display a media search error after feeding the media for about 3m.

Step 6: Installing the scroller slip ring Install the scroller slip ring onto the scroller. Slide the scroller slip ring on the left side of the scroller (side with fixed flange).

Step 7: Installing the scroller Install the scroller as follows: a) Stand at the back side of the printer, holding the scroller with the fixed flange side in

your left hand. b) Slide the scroller (left side) into the scroller receiver, as shown in the illustration. c) Push the scroller (Right side - movable flange side) down into the right scroller receiver.

You will notice it dropping nicely into place.

Step 8: Locking the scroller slip ring Lock the scroller by sliding the scroller slip ring onto the scroller rollers. The scroller slip ring will prevent unwinding of the roll media from the scroller when roll media is still not loaded in the machine.


Page 46 AP-75024 Rev. 1.2. – 18/08/2002

Step 9: Loading roll media

• Pull some media off the roll, feed it into the media feed gap and between the pressure rollers and the drive roller.

• Pull out the media at the front side and make sure at least 0.5 meters hangs out in front of the printer.

Caution: • When you load roll media from the back, be careful not to hurt

yourself by touching the pressure roll system.

Step 10: Checking the position of roll media Turn the scroller by hand and wind up several turns of roll media. As you wind up the media, check the relative positions of the drive roller on the right and the right hand edge of the roll media. It is normal if with the roll media pulled tight, the portion that is being wound and the portion that was unwound are straight and the right hand side edge of the media is on the guide line. If this is not the case, adjust the position of the roll media in accordance with step 9.

Guide line (holes) can be seen Guide line (holes) is hidden

Step 11: Fine-tuning the roll media position If the guide line (holes) can be seen, the roll media must be moved to the right. If the guide line (holes) is hidden, the roll media must be moved to the left.

• Turn the scroller receiver screw counter-clockwise to move the roll media to the right (when standing in front of the printer).


Page 47 AP-75024 Rev. 1.2. – 18/08/2002

• Turn the scroller receiver screw clockwise to move the roll media to the left (when standing in front of the printer).

Important: • The guide line (holes) is a guide. There is a possibility of a jam if the pressure roller is not holding the left edge of the media and the pressure roller is near the right edge. Either hold the left edge of the media completely with the pressure roller or slide it so that the pressure roller is about 5 mm away from the right edge of the media and the right edge of the media within 5 mm to the left or right of the guide line (holes).

Step 12: • Check if the roll media has been installed correctly. • Lower the media hold lever and close the cover. • The head moves automatically and detects the media size. • The display will show the following message during loading: • After performing its media loading sequence (± 30 seconds) the printer displays the

following message:

Important: • If the roll media has not been fed straight or incorrectly,

messages such as, “media error” or “media jam error” are shown on the display. If this is the case, reload the media following the instructions above.

ConfirmPaperKind

Plot OK


Page 48 AP-75024 Rev. 1.2. – 18/08/2002

Step 13: During the media detection sequence, check if the media runs straight. After media detection, check the position of the right side of the roll media. If the position is almost on the same line as it was before closing the cover, media loading was performed successfully. If after the media detection sequence, the roll media position is not on the same position as it was before closing the cover, repeat the instructions from steps 8 and 9 for installing the media.

Note: Removing roll media Step 1: After printing, open the cover, tilt the media hold lever UP and wind up the roll media.

Step 2: Stand behind the printer. Unlock the scroller receiver by pressing the lock lever down. You can now lift the right side of the scroller and remove it from the printer.

Step 3: Remove the roll media by gently pushing the roll media off the scroller via the moveable flange side. At no times drop the scroller end-caps on the floor as this might damage the scroller end-caps and reduce media tracking or loading problems.

3. Loading media in combination with the Roll Take-Up System. Step 1 : Open the cover and put the hold lever in the UP position by tilting it up(wards).


Page 49 AP-75024 Rev. 1.2. – 18/08/2002

Step 2 : Selecting roll take-up system • Press the Media-key to select

media loading sequence with roll take-up system (Both LEDs ON).

• By pressing the key you will see the

LEDs alternate between three choices (sheet, roll and take-up). Now select roll take-up loading sequence (both LEDs ON).

Step 3 : Take an empty cardboard core. Slide the empty cardboard roll over the scroller of the roll take-up system.

Note : Notice that one flange is fixed. A warning sticker is attached near the flange. Do not remove this flange.

Step 4 : Take your roll of media. Step 5 : Remove the moveable flange from the scroller by pulling it off.

Movable Flange Step 6 : Load the media onto the scroller. Feed the scroller through the media core. Gently but firmly press the roll media over the fixed flange. Slide the moveable flange over the scroller and firmly press the flange inside the roll media core.


Page 50 AP-75024 Rev. 1.2. – 18/08/2002

1 = Fixed flange 2 = Media winding direction

Note : • Do not drop the media roll over the scroller as this might damage

the scroller end caps. Damaged end caps may cause media tracking problems.

• All Mutoh recommended roll media are rolled up with the printable side facing the outside, so that you can load the roll media easily.

Step 7: Installing the scroller slip ring Install the scroller slip ring onto the scroller. Slide the scroller slip ring on the left side of the scroller (side with fixed flange).

Step 8 : Installation of the scroller. Install the scroller as follows : a) Stand at the back side of the printer, holding the scroller with the fixed flange side in

your left hand. b) Slide the scroller (left side) into the scroller receiver, as shown in the illustration. c) Push the scroller (Right side – movable flange side) down into the right scroller

receiver. You will notice it dropping nicely into place.


Page 51 AP-75024 Rev. 1.2. – 18/08/2002

Step 9: Locking the scroller slip ring Lock the scroller by sliding the scroller slip ring onto the scroller rollers. The scroller slip ring will prevent unwinding of the roll media from the scroller when roll media is still not loaded in the machine.

Step 10 : Loading roll media.

Pull some media off the roll, feed it into the media feed gap and between the pressure rollers and the drive roller.

Pull out the media at the front side and make sure at least 0.5 meters hangs out in front of the printer.

Caution : When you load roll media from the back, be careful not to hurt yourself by touching the pressure roller system.

Step 11 : Checking the position of roll media. Turn the scroller by hand and wind up several turns of roll media. As you wind up the media, check the relative positions of the drive roller on the right and the right hand edge of the roll media. It is normal if with the roll media pulled tight, the portion that is being wound and the portion that was unwound are straight and the right hand side edge of the media is on the guide line. If this is not the case, adjust the position of the roll media in accordance with step 9.


Page 52 AP-75024 Rev. 1.2. – 18/08/2002

Guide line (holes) can be seen Guide line (holes) is hidden

Step 12 : Fine-tuning the roll media position. If the guide line (holes) can be seen, the roll media must be moved to the right. If the guide line (holes) is hidden, the roll media must be moved to the left. • Turn the scroller receiver screw counter-

clockwise to move the roll media to the right (when standing in front of the printer).

• Turn the scroller receiver screw clockwise to move the roll media to the left (when standing in front of the printer).

Important: • The guide line (holes) is a guide. There is a possibility of a jam if the pressure roller is not holding the left edge of the media and the pressure roller is near the right edge. Either hold the left edge of the media completely with the pressure roller or slide it so that the pressure roller is about 5 mm away from the right edge of the media and the right edge of the media within 5 mm to the left or right of the guide line (holes).


Page 53 AP-75024 Rev. 1.2. – 18/08/2002

Step 13 : • Before lowering the media hold lever, hold the media on the front side and turn the

media feeding scroller slightly backward, making sure that there is an even tension across the full media width.

• Lower the media hold lever and close the cover. • The head moves automatically and will search for the left and right edge of the media

being loaded.

Important : If the roll media has not been fed straight or incorrectly, messages such as “Stuck Media error” or “Take out paper” are shown on the display. If this is the case, reload the media following the instructions mentioned above.

Step 14 : In the MENU “Function” of your printer, set media cut to OFF. Step 15 : Feed the media forward by pressing the SHIFT & ADVANCE keys simultaneously until the media reaches the cardboard core on the take-up system.

Step 16 : Fix the media on the cardboard core by means of self-adhesive tape strips in the middle and on the left and right side.

Note : First attach the middle of the media on the cardboard core to avoid slipping of the media.

Step 17 : Feed the media slightly forward (using SHIFT & ADVANCE) and wind it up on the take-up system. Now you are ready to start printing.


Page 54 AP-75024 Rev. 1.2. – 18/08/2002

Once the printer has printed as much as shown on the figure below, the sensors will be activated and the take-up system will start winding up the media.

Once your print is finished and dry you can wind up your print via a manual feed button. If you want to sheet off the print push the cancel button for 2 seconds and confirm the sheet-off request. If you want to wind up or wind off your print you can do this via the forward / reverse button.


Page 55 AP-75024 Rev. 1.2. – 18/08/2002

USING PRE- AND POST-HEATERS. Use the Pre- and Post-heater for uncoated or slow-drying media. With the Heaters you can get a wider range of media compatibility. When using the heaters set it on the maximum temperature.

Important : Depending on the use of media, it is possible that media starts to curl. If this is the case, lower the temperature.

USING ECO-SOLVENT INK • Before installing or changing to Eco-Solvent ink, perform a Head Wash. The tubes and

heads must be clean. Use the special Eco-Solvent Transition Liquid. • Once you have worked with eco-solvent inks, it is forbidden to change to another ink

type. • Prints are UV- and water-resistant for up to three years outdoors (*). Lamination is

required for heavy-duty applications. • No need for special ventilation or environmental equipment. (*) Accelerated weather tests predict up to 3 years outdoor durability. Outdoor durability is location and application dependant.

USING PIGMENTED INK • Pigmented ink tends to dry faster than dye ink. Make sure to clean the head cleaning

wiper regularly in order to avoid head clogging. (See section: cleaning head cleaning wiper)

• Pigmented inks at all times require the ink density to be set to NORMAL. These inks

are not compatible with FAINT nor with THIN ink density mode which both use the micro-dot printing mode.

• If you have a RIP software in which media profiles are available for the Mutoh ink/media

combination, the software normally should disable the micro-dot mode as soon as a profile for pigmented ink is selected. It is best however, always to double check this.


Page 56 AP-75024 Rev. 1.2. – 18/08/2002

PRINT ORIGIN CONTROL. The Origin-Reset function allows you to move the horizontal origin, effectively changing the offset versus the right border. The value can be set ranging from 0 mm to the media width minus the left and right margins (20 mm), in 1mm increments. The inclusion of this function allows you to manually nest images, working in conjunction with the Media Feed Reverse button on the control panel of the printer (See Control Panel Section below). In a typical application, an image narrower than the media width would be printed flush with the right margin. After printing, the media can be fed back into the printer using the Media Feed Reverse button. Then, the horizontal origin can be moved using the Origin-Reset function in the User Menu under the Functions submenu. Using this method, the next image would automatically be printed to the left of the first image, rather than behind it, thus avoiding excess media waste. Note, however, that once set, the Origin-Reset function will remain set until changed again or reset to zero by the user.

Plot OK

Step 1 : To enter the Menu system, press the [MENU] key.

* Menu * Command >

Step 2 : The key contents changes according to the yellow section on the outside of the control panel. Bring up the “Command” menu by pressing the [Menu up] key or [Menu Down] key.


Page 57 AP-75024 Rev. 1.2. – 18/08/2002

* Menu * Command >

Step 3 : Press the [ENTER] key to confirm the “Command” menu and shift to the next level.

OriginReset : No

Step 4 : Bring up the “OriginReset” item by pressing the [Menu up] key or [Menu Down] key.

OriginReset : Yes

Step 5 : Press the [Value/+] or [Value/-] key to select “Yes” or “No”.

Origin : Init

Step 7 : Press the [Value/+] or [Value/-] key to select “new origin” or “Initialisation”.

Origin : New>

Step 8 : To select a new origin select “New>” and press the [ENTER] key to confirm.

Offset : 0

Step 9 : Set a new origin (0 to media width minus 20 mm) and press the [ENTER] key to confirm.

* Menu * Command >

Step 10 : Do not press any other keys for 3 minutes or press [BACK] key

Plot OK

Step 11 : The permanent ONLINE-status display is restored.

Note : Once set, the Origin-Reset function will remain set until it is reset to zero or until it is changed by the user.


Page 58 AP-75024 Rev. 1.2. – 18/08/2002

MICRO-BANDING ELIMINATION. The nominal paper movement accuracy is ± 0.1 percent, or ±1 mm per meter of moving distance. Different media types may show different behavior and when the paper movement error exceeds the target specification, banding can occur. This banding can take the form of thin dark horizontal bands, or thin white horizontal bands. If the above happens, these bands will occur in both bi-directional and unidirectional print modes. Thin dark bands indicate that the printer firmware is under-compensating and that print swaths are overlapping on the edges. Alternatively, thin white lines indicate that the printer firmware is over-compensating, and that print swaths are not perfectly butted together. The media feed micro step adjustment option gives the user the ability to steer the step compensation algorithm. To eliminate micro-banding, you can enter a positive or negative percentage of compensation, (± 3.00 percent), in 0.01 percent increments. A positive value will extend the step and compensate for overlapping print swaths; a negative value will shorten the step and compensate for non-butting print swaths. Some trial and error testing is typically required to find the optimum value for any given media type.

Plot OK


* Menu * Command >

Step 2 : The key contents change to the yellow section on the outside of the control panel. Bring up the “Function” menu by pressing the [Menu up] key or [Menu Down] key.


Page 59 AP-75024 Rev. 1.2. – 18/08/2002

* Menu * Function >

Step 3 : Press the [ENTER] key to enter the “Function” menu and shift to the next level.

Step Adjustment : Change

Step 4 : Bring up the “Step Adjustment” item by pressing the [Menu up] key or [Menu Down] key.

Step Adjustment : Clear

Step 5 : Press the [Value/+] or [Value/-] key to select “Change” or “Clear” and press ENTER.

Step Adjustment : 0.00%

Step 6 : When pressing “Change”, enter the new value using the [VALUE/+] / [VALUE/-] keys. Using the [MENU UP] / [MENU DOWN] keys, you can select which digit you want to change. The value can be changed in 0.01% increments. Press [ENTER] to confirm the new value.

Step Adjustment : Change

Step 7 : If no other items are to be changed, press the [BACK] key.

* Menu * Function >

Step 8 : Do not press any other keys for 3 minutes or press [BACK] key

Plot OK

Step 9 : The permanent ONLINE-status display is restored.


Page 60 AP-75024 Rev. 1.2. – 18/08/2002

Note : To find the optimum correction value for a certain media, you will need to go through a series of test cycles. Preferably send to the plotter a small test image such as a neutral grey square (between 50% and 70% Grey) and check the micro-banding as described above. Make a note of your correction value for a certain media type, as the required value will always be the same for this media type.

Note : Before using this function, always perform a nozzle-check to see if all nozzles are firing correctly. Nozzles which are not firing or misfiring might mislead you when entering correction values.

Daily Maintenance Operation Instructions Rockhopper Printer

Page 61 AP-75024 Rev. 1.2. – 18/08/2002

DAILY MAINTENANCE

REPLACING THE INK CASSETTES When the Rockhopper printer indicates or insert or replace the ink cassette(s) as soon as possible. When the indication is , prepare to have new ink cassettes available. Step 1:

If the display shows , pull out the empty or in-operational ink cassette.

Note: • Each sign [Y] [M] [C] [K] indicates:

Y : Yellow, M : Magenta, C : Cyan, K : Black. • [O] indicates: Orange or Light Cyan • [G] indicates: Green or Light Magenta

Step 2: Unpack a new ink cassette.

Note: • Only use original Mutoh ink cassettes. • For each cassette, there is a correct place and a correct inserting

direction. • Open the ink cassette just before inserting it into the slot. • Use ink cassettes within two years from the date printed on the

package. • Replace your ink cassettes at least every 6 months.

Step 3: Insert a new ink cassette into the slot.

Step 4: When insertion / replacement of ink cassettes has been performed well, the display will show the following message if media is loaded and the printer is ONLINE:

No Ink No Cartridge

Ink low

Plot OK

No Ink


Page 62 AP-75024 Rev. 1.2. – 18/08/2002

SWITCHING BETWEEN DYE INKS AND PIGMENTED INKS OR CHANGING TO ECO-SOLVENT INK. Use the INK CHANGE procedure to switch from DYE ink to PIGMENTED ink or from PIGMENTED ink to DYE ink. Use the INK CHANGE procedure to switch from Dye or Pigmented Ink to ECO-SOLVENT INK.

Important : After using Eco-Solvent ink it is not possible to change to other type of ink (pigmented and dye Inks). Before installing and changing to Eco-Solvent ink, the machine needs to go through a cleaning cycle with special Eco-Solvent transition liquid.

When using this function, cleaning cassettes need to be installed to the cassettes slots.

Plot OK


* Menu * Command >

Step 2 : The key contents change to the yellow section on the outside of the control panel. Bring up the “Utility” menu by pressing the [Menu up] key or [Menu Down] key.

* Menu * Utility>

Step 3 : Press the [ENTER] key to enter the “Utility” menu and shift to the next level.

InkChange : No

Step 4 : Bring up the “InkChange” item by pressing the [Menu up] key or [Menu Down] key.

InkChange : Yes

Step 5 : Press the [Value/+] or [Value/-] key to select “Yes” and press ENTER.

Change Waste Ink

Step 6 : Empty the waste ink bottles.

Change Tank ? Yes



Page 63 AP-75024 Rev. 1.2. – 18/08/2002

ConfirmChange Yes


Remove Cart

Step 9 : Remove ink cartridges from the slot.

Set Wash Cart Head Wash

Step 10 : Insert the cleaning cartridge to the ink cartridge slots. Use the special Eco-solvent Transition Liquid when changing to Eco-solvent ink. The head wash starts when the cleaning cartridge is inserted. The cleaning period is approximately 15 minutes.

Remove Wash Cart

Step 11 : Remove the cleaning cartridge from the slot.

Head Wash

Step 12 : The rest of the cleaning fluid in the printer unit is discharged when the cleaning cartridge is removed.

Change Waste ink

Step 13 : Empty the waste ink bottle from the printer unit.

Change Tank ? Yes


ConfirmChange Yes


[YMCK] Discharged

Step 16 : If the cassettes that have been removed are DYE ink cassettes, now insert PIGMENTED ink cassettes or ECO-SOLVENT ink cassettes. If the cassettes that have been removed are PIGMENTED ink cassettes, now insert DYE ink cassettes or ECO-SOLVENT ink cassettes.


Page 64 AP-75024 Rev. 1.2. – 18/08/2002

Important : After using Eco-Solvent ink it is not possible to change to other type of ink (pigmented and dye Inks).

Ink Refill 4M Ink Refill 3M Ink Refill 2M Ink Refill 1M Ink Refill 0M Ink Refill 4M Ink Refill 3M Ink Refill 2M Ink Refill 1M Ink Refill 0M

Step 17 : The initial fill is executed when installing cartridges. The display will show the following messages :

Plot OK

Step 18 : After filling, the display will show the following message :

Note : • The cleaning cartridge is one time use only. • Only recommended ink cassettes can be used. The also need to be

turned in the proper direction for insertion. • Ink cassettes should be used within two years of the date that is

printed on the package. Cassettes that have been loaded into the printer should be replaced within six months.


Page 65 AP-75024 Rev. 1.2. – 18/08/2002

CLEANING THE HEAD CLEANING WIPER.

When the head is cleaned and the type of ink is changed frequently, waste matter clinging to the cleaning wiper may cause the printing to become faint or blemished. In such case, you should clean the cleaning wiper. Step 1: Switch off the power, lower the hold lever and bring the head to the middle.

Caution: • Do not move the head with the hold lever up. The head and media

keeper blade may touch, causing damage and poor printing quality.

Step 2: Clean the cleaning wiper backwards and forwards two or three times with the cloth for cleaning the cleaning wiper.

1. Head cap unit 2. Cleaning wiper

Caution: • Clean without your hand coming into direct contact with the head cap

unit, which is near the cleaning wiper. Otherwise oil may get on the cleaning wiper and it will be unable to clean the head properly.

• Do not lift up the cleaning wiper when you are cleaning it. Otherwise it is unable to clean the head properly.

• The cleaning wiper and its surroundings will be soiled with waste liquid. Be careful not to dirty your hands and clothes.

Step 3: Return the head to its former position at the right hand end of the printer.

Caution: • The head may be damaged by drying ink, etc. if it is not returned to the

right hand end of the printer.


Page 66 AP-75024 Rev. 1.2. – 18/08/2002

REPLACING THE CUTTING BLADE

Depending on the kind of roll media used, paper dust gathers in the cutter slot and on the cutter blade edge. This may cause bad sheeting off quality. In this case, replace or clean the cutting blade or/and clean the cutter slot. The cutting blade is a consumable item, so if the blade loses sharpness, replace it. We recommend replacing the cutting blade regularly.

Caution: The hold lever must be down. Do not move the head with the hold lever up. The head and media keeper may touch, causing damage and poor printing quality.

Step 1: Switch off the printer and pull the printing head to the center of the printer. Step 2: Take out the cutting blade by pushing the cutter head down and rotating the cutter arm towards you. Either clean the cutting blade with a dry cloth or replace it.

Caution: • There is a spring fitted in the hole of cutter head. Be careful not to

loose it while replacing the cutting blade.

Step 3: Insert a new cutting blade in the hole of the cutter head. While pushing the cutting blade down, put the cutter arm back over the cutting blade. A cutting blade can only be inserted in one direction.


Page 67 AP-75024 Rev. 1.2. – 18/08/2002

Caution: • The edge of the cutting blade is very fragile, while replacing it, handle

it with care.

Step 4: Put the head manually back into its capping position, and turn the power switch ON.

Note: • Durability of the cutting blade may differ depending on the kind or

thickness of the media and used environment. We recommend purchasing a spare cutting blade so that you always have a spare blade at hand.

Important: If you don’t have a new sheet-off blade available to replace your blade, you can temporarily switch off the automatic sheet-off. Press menu until you see Function. Press Enter Function Ink Dry Time. Press menu until you see “Media Cut : ON” Press value + or value -: “Media Cut : OFF” Press Enter Press Back 2 times to go back to ONLINE Level.

Control Panel Operation Instructions Rockhopper Printer

Page 68 AP-75024 Rev. 1.2. – 18/08/2002

PERIODICAL MAINTENANCE You have to change some parts of the Rockhopper printer to obtain a good quality. Please refer to the tables for an overview of periodical maintenance. You will notice that the X-marks indicate a renewal of the mentioned part(s) after this many months. You have to change the absorbents every week.

IMPORTANT : Note that the x-marks in month 6 and month 12 are only to be done by authorized Mutoh technicians.

Maintenance cycle on Rockhopper 48 “

Monthly Description Qty 1 2 3 4 5 6 7 8 9 10 11 12Print Head 2 X Flush Box Spare Part 1 X X Wiper 1 X X Sensor on ext. Waste Bottle syst. 1 X Maint. Station GA Assy RJ-6100 1 X X Waste Connection tube small 2 X X Dust removal in fan area - X Cleaning maintenance Station - X X Cleaning bottle 1 X X Blade on press roller 4100/6100P 18 X F-absorbent 1 RJ-4100 4 WEEKLY

Maintenance cycle on Rockhopper 62 “

Monthly Description Qty 1 2 3 4 5 6 7 8 9 10 11 12Print Head 2 X Flush Box Spare Part 1 X X Wiper 1 X X Sensor on ext. Waste Bottle syst. 1 X Maint. Station GA Assy RJ-6100 1 X X Waste Connection tube small 2 X X Dust removal in fan area - X Cleaning maintenance Station - X X Cleaning bottle 1 X X Blade on press roller 4100/6100P 24 X F-absorbent 1 RJ-4100 4 WEEKLY


Page 69 AP-75024 Rev. 1.2. – 18/08/2002

UNDERSTANDING THE CONTROL PANEL & PRINTER CONTROLS

GUIDED TOUR AROUND THE CONTROL PANEL Your printer is equipped with a direct access control panel, meaning that all frequently used functions can be addressed directly from the keyboard.

Nr. Key Description 1. Data LED :

The DATA LED monitors DATA status : • LED ON indicates data is being received. • LED FLASHING means data is being processed.

2. Error LED :

The ERROR LED is ON after an ERROR has occurred, to indicate a possible hazardous situation. The LED will go out if the error is corrected or after pressing the [CANCEL] key.


Page 70 AP-75024 Rev. 1.2. – 18/08/2002

3. Cancel Key :

The [CANCEL] key is a special key, controlling both the CANCEL FUNCTION as well as the ROLL MEDIA sheet-off function.

Printer Condition Result by pressing CANCEL

Idle Status Roll media is cut at the current position

Receiving Status Process stops

Process Status Buffer is cleared

Printing Status Print is cancelled, buffer is cleared, printed part is cut-off.

To request a sheet-off, press cancel for 2 seconds and confirm with [ENTER].

4. Cleaning :

- Pressing for 2 seconds initiates the cleaning procedure.

- When pressed together with the [SHIFT] key,

(9) it initiates the head adjustment procedure.

- Go to the Previous Menu, when in menu-mode operation.

- For advanced Cleaning Control, enter the menu

system and select submenu [Utility] – option [Clean].

5. Quality / Speed :

- Pressing QUALITY / SPEED will change the output quality and speed. Each time the key is pressed you will notice the LED indicator showing the current status : High quality, Normal and High Speed.

- The set-up can only be changed in idle status.

- When pressed together with [SHIFT] key (9)

outputs the Test Print.

- Go to the Next menu option, or increase a parameter value when in menu-mode operation.

- The LED indication is also influenced by data

coming from the RIP/driver software.


Page 71 AP-75024 Rev. 1.2. – 18/08/2002

6. Resolution :

- Pressing RESOLUTION will change the output resolution between 360 DPI, 720 DPI or 1440 DPI. The set-up can only be changed in idle status.

- When pressed together with the [shift] key (9)

it allows reverse manual roll feed. - Select the previous menu option and decrease

a parameter value when in menu mode operation.

- If both LEDs are ON simultaneously the plotter

operates in one of the 3 available 1440 dpi modes (horizontal, vertical or diagonal).

- The LED indication is also changed by data

coming from the RIP software.

7. Media :

- Allows selection among roll, cut-sheet or media take-up system support.

- When pressed together with the [shift] key (9),

generates a nozzle check print. - Accept a new setting when in menu mode or

enter a lower menu level.

8. Menu Mode Operation : The Menu Mode Operation is used to change printer settings and parameters. Menu Mode related buttons are enclosed in the yellow area.


Page 72 AP-75024 Rev. 1.2. – 18/08/2002

9. Shift-button :

- Shift button to activate Head Adjustment, manual roll feed (forward or reverse), Nozzle check print, Test print or Set-Up List.

- Back out of menu levels or switch back to

ONLINE level from top level (Menu mode operation).

10. Menu :

- The Menu Mode Operation is used to change printer settings and parameters.

- Press the [MENU] key to switch from ONLINE

status to menu mode operation. - When pressed together with the [shift] key (9)

it allows forward manual roll feed.

11. Liquid Cristal Display :

16 characters LCD display which displays messages, shows settings / values and allows menu-wise control.

12. Vacuum :

- The Vacuum key allows you to reduce the fan power when using very light media such as synthetic paper or uncoated paper lighter than 70 g/m².

- When pressed together with the [SHIFT] key,

(9) it initiates a Set-up List and an adjustment parameter plot.


Page 73 AP-75024 Rev. 1.2. – 18/08/2002

Note : • When the data light is ON (receiving) or blinking (processing), all the

keys are disabled, except the head cleaning key. The keys will be operational in case of receiving data while you are in the setup menu. The settings changes, however, will then only be valid for the next printing job.

• Panel set up from the printer is only possible when no printing data or processing data is sent to the printer.

• In menu mode operation, the shift key functions are not available.


Page 74 AP-75024 Rev. 1.2. – 18/08/2002

HEATER SYSTEM CONTROL PANEL.

1 = Controls Front Heater 2 = Controls Rear Heater 3 = Power Switch Power Switch: Control for power ON or OFF the Heater System. Controls Front Heater: Set temperature for the front heater. Real (RT) and set (ST) temperature are displayed on the LCD screen. The maximum temperature is 50 °C. By pushing the buttons you can select an appropriate temperature. Controls Rear Heater: Set temperature for the rear heater. Real (RT) and set (ST) temperature are displayed on the LCD screen. The maximum temperature is 50 °C. By pushing the buttons you can select an appropriate temperature.

1 2 3


Page 75 AP-75024 Rev. 1.2. – 18/08/2002

MENU MODE OPERATION. The Menu Mode Operation is used to access settings, which cannot be controlled via the direct access keys. As soon as media is loaded, the printer is ONLINE and ready to receive data. In case no media is loaded, the printer is OFFLINE. To enter the MENU MODE proceed as follows : 1. Press the MENU-key. 2. To select the next/previous menu item press Menu Down ↓ / Menu Up ↑. 3. To select the next/previous option or value press value + / value -. 4. To accept a new setting or enter a next menu level press ENTER. 5. To return to a previous menu level, or exit the menu system press Back ←. In case Media is loaded, exiting the top menu level will switch the printer back to ONLINE.


Page 76 AP-75024 Rev. 1.2. – 18/08/2002

Menu Structure – overview.

Command MH-GL2 / MHGL, GL2 / RTL-PASS

Printer command language selection

PlotArea Normal / Expend Set-up hard clip area depending of media size.

Position P1 / Full / LL Set-up initial pen position in MH-GL, GL2 and MH-GL2.

Terminat Special / Normal Command Language terminator selection.

Resolut 720dpi / 360dpi / 300dpi Select logical resolution. OnlineTimer Off / 10s / 20s / 30s / 40s

/ 50s / 60s / 90s / … / 780s / 800s

In case of intermittent data flow, determines time-out to finalize plot.

Overwrite Last / Mix Set-up control of overlapping areas.

Command

OriginReset No / Yes Allows manual nesting when combined with backward feed.

InkDryTime 0 sec to 5 sec to 30 sec to 60 min.

Set-up ink drying time before sheet-off occurs.

Halftone Quality / Speed / Thin Select method of pseudo-tone processing.

KCMY→KMY Yes / No Reserved for future use. CMY→Black Yes / No Allow mixed black (CMY) or

not. KYCMYK No / Yes Reserved for future use. Scale 25% to 100 % to 400% Expand or reduce print

data. Mirror Off / Y On Reverse printing set-up. Direct. Command / MAX-MIN Media size determined by

Page size Command or by plot data.

Cut Position Data / Standard Specify cutting position on roll media following data or standard media size.

MediaCut Auto / Off / Manual Automatic sheet-off set-up. Copy 1 to 99 Set-up number of copies. InkDensity Normal / Micro Select Normal or Micro dot

drop size in function of media & ink type.

Dist.Adj No / Clear / Change / Confirm

Plot distance adjustment.

Function

StepAdj Change / Clear Micro-banding elimination via microstep adjustment.

Mode Bi Centro / Centro Select between uni-directional and ECP high speed.

Centro

Timing A – B / B – A Select ACK timing for BUSY state.

Network IP Address 000.000.000.000 to 192.034.041.015 to 255.255.255.255

ErrorDisplay Off / On Show or hide simple error. No Initialize printer set-up.

Yes InitialAll No / OK Initialize printer set-up. InitialCommand No / OK Initialize printer set-up. InitialFunct No / OK Initialize printer set-up. InitialCentro No / OK Initialize printer set-up.

Initialize

InitialNetwork No / OK Initialize printer set-up. Dump Start – End / All (Cancel

with CANCEL-key) Set-up data dump mode.

Wash Starts manual head wash before ink type switching.

Normal Starts a NORMAL cleaning Clean Powerful Starts a POWERFUL

cleaning No Fill Yes Starts a Ink Fill Sequence

Ink Change No / Yes Starts ink Change Procedure

Online

Utility

Maintenance Rec.

Prints maintenance record.


Page 77 AP-75024 Rev. 1.2. – 18/08/2002

PRINT MODES ACCESSIBLE VIA THE CONTROL PANEL. The following print modes are predefined as Draft, Normal and Quality. These modes may be overwritten from the host computer using the printer manager commands. Panel LEDs Print Mode m²/h Output Resolution (dpi) 360 – Draft 1-Pass / Bi-directional 14.49 360 x 180 360 – Normal 1-Pass / Unidirectional 10.87 360 x 180 360 – Quality 2-Pass / Unidirectional 5.43 360 x 360 720 – Draft 2-Pass / Bi-directional 7.25 720 x 360 720 – Normal 2-Pass / Unidirectional 5.43 720 x 360 720 – Quality 2-Pass / Unidirectional 2.72 720 x 360 1440 – Draft 8-Pass / Bi-directional 1.81 1440 x 1440 1440 – Normal 8-Pass / Unidirectional 1.81 1440 x 1440 1440 – Quality 16-Pass / Unidirectional 0.68 1440 x 1440


Page 78 AP-75024 Rev. 1.2. – 18/08/2002

Documents

Http Www.mutoh.be Binarydata.aspx Type=Doc Rock Hopper e