Huawei.H35-210 V2.5.v2021-09-23

Huawei.H35-210_V2.5.v2021-09-23.q105

Exam Code: H35-210_V2.5

Exam Name: HCIA-Access V2.5

Certification Provider: Huawei

Free Question Number: 105

Version: v2021-09-23

# of views: 105

# of Questions views: 1240

https://www.freecram.com/torrent/Huawei.H35-210_V2.5.v2021-09-23.q105.html

NEW QUESTION: 1Is the following description correct? The access network upgrade loading file transfer canuse FTP, TFTP, or SFTP, and FTP is recommended.A. FalseB. TrueAnswer: B (LEAVE A REPLY)

NEW QUESTION: 2In the H.248 protocol, the terminal can be programmed to detect events. Once theseevents are detected, the MG will send a report to the MGC or the MG will takecorresponding actions.A. AuditCapabilitiesB. ModifyC. NotifyD. ServiceChangeAnswer: C (LEAVE A REPLY)

NEW QUESTION: 3Is the following description correct? VDSL2 provides uplink and downlinksymmetrical/asymmetrical transmission rates on a pair of twisted pairs. The transmissiondistance is about 3km. The maximum downlink rate is 52M (symmetrical rate) and themaximum uplink rate is 12M (asymmetrical rate).A. FalseB. TrueAnswer: A (LEAVE A REPLY)

NEW QUESTION: 4

https://www.freecram.com/torrent/Huawei.H35-210_V2.5.v2021-09-23.q105.html

https://www.freecram.com/q/9359-1018324/



Is the following description correct? ADSL2+ is an extension of ADSL technology,supporting a downlink rate of up to 24Mbit/s and an uplink rate of 2.5Mbit/s, and thelongest transmission distance can reach 6.5km.A. TrueB. FalseAnswer: A (LEAVE A REPLY)

NEW QUESTION: 5In the H.248 protocol, how to apply for gateway registration?A. Send MOD_REQ from MGC to MGB. Send SVC_CHG_REQ from MGC to MGC. Send MOD_REQ from MG to MGCD. Send SVC_CHG_REQ from MG to MGCAnswer: D (LEAVE A REPLY)

NEW QUESTION: 6During the configuration of the EPON PPPoE service, what templates need to beconfigured to increase the MDU?A. Route templateB. DBA templateC. System parameter templateD. Traffic templateAnswer: (SHOW ANSWER)

NEW QUESTION: 7What is the attenuation of the 1:2 splitter?A. 8dbB. 3dbC. 13dbD. 5dbAnswer: B (LEAVE A REPLY)

NEW QUESTION: 8According to the IEEE 802.1Q standard, where is the VLAN identification field in theEthernet frame?A. After the source MAC address and destination MAC addressB. Before source MAC address and destination MAC addressC. Between the source MAC address and the destination MAC addressD. Not fixedAnswer: A (LEAVE A REPLY)






NEW QUESTION: 9Is the following description correct? Version rollback generally includes three steps: 1.Load the original version of the package file; 2. Load the original version database backedup before the upgrade; 3. Reset the system.A. TrueB. FalseAnswer: (SHOW ANSWER)

NEW QUESTION: 10Is the following description correct? It is impossible for a route in the routing table to have amask of0.0.0.0Routing items.A. TrueB. FalseAnswer: (SHOW ANSWER)

NEW QUESTION: 11When locating ADSL faults, what reasons may cause ADSL Modem to fail to activate?A. Line activation template configuration errorB. Line problem, or MODEM failureC. All of the above are possibleD. Board failure or port failureAnswer: (SHOW ANSWER)

NEW QUESTION: 12What is the index range of MA5600 extended access control list?A. 3000-3999B. 1-999C. 2000-2999D. 1000-1999Answer: (SHOW ANSWER)

NEW QUESTION: 13How many channels of ADSL2+&POTS access services are provided by the MA5600TADSL2+&POTS integrated service board H80BCAME?A. 48B. 32C. 64D. 16Answer: A (LEAVE A REPLY)

NEW QUESTION: 14






What services does TCONT 0 generally run in ONT?A. IPTVB. OMCIC. InternetD. VoIPAnswer: B (LEAVE A REPLY)

NEW QUESTION: 15Is the following description correct? The VDSL2 standard specifies a frequency banddivision of up to 30MHz, which can realize 100Mbit/s high-speed data transmission in asymmetrical uplink and downlink within a short distance.A. TrueB. FalseAnswer: A (LEAVE A REPLY)

NEW QUESTION: 16Which of the following statements about ONT tcont is incorrect?A. tcont 1 generally carries OMCI channelsB. Uplink bandwidth is divided based on T-CONT, and different services use different T-CONTsC. One ONU/ONT can contain multiple T-CONTsD. The GEM port is used as a service channel. A GEM port can carry one or more servicesin the flowAnswer: (SHOW ANSWER)

Valid H35-210_V2.5 Dumps shared by Fast2test.com for Helping PassingH35-210_V2.5 Exam! Fast2test.com now offer the newest H35-210_V2.5 examdumps, the Fast2test.com H35-210_V2.5 exam questions have been updated andanswers have been corrected get the newest Fast2test.com H35-210_V2.5 dumpswith Test Engine here: https://www.fast2test.com/H35-210_V2.5-practice-test.html (301

Q&As Dumps, 40%OFF Special Discount: freecram)

NEW QUESTION: 17At a certain UA5000 site, due to resource constraints, the entire frame of ADSL users needto pass a VLAN upstream to the IP network. At this time, why should the upstream VLANin the IPM board be defined?A. smart vlan;B. standard vlan;C. super vlan




https://www.fast2test.com/H35-210_V2.5-practice-test.html

D. mux vlan;Answer: A (LEAVE A REPLY)

NEW QUESTION: 18MA5600T checks whether the currently running single board software version meets therequirements for on-site deployment. Which command is used?A. display languageB. display boardC. All of the aboveD. display versionAnswer: (SHOW ANSWER)

NEW QUESTION: 19What is the maximum splitting ratio supported by the MA5680T GPBC board?A. 1:16B. 1:128C. 1:64D. 1:32Answer: C (LEAVE A REPLY)

NEW QUESTION: 20What is not included in the uplink mode of MA5616?A. GPONB. FEC. EPOND. GEAnswer: B (LEAVE A REPLY)

NEW QUESTION: 21Which of the following information is the information that Solaris environment variables canprovide?A. Shell usedB. PathC. Default routeD. Default editorAnswer: A,B,D (LEAVE A REPLY)

NEW QUESTION: 22Two-stage optical splitter is connected to the PON, the first-stage is 1:2, the second-stageoptical splitter is 1:16, what is the total splitting ratio?A. 1:16






B. 1:32C. 1:18D. 1:2Answer: (SHOW ANSWER)

NEW QUESTION: 23The Ethernet switch works inOSIWhich layer of the reference model?A. data link layerB. Transport layerC. Physical layerD. Network layerAnswer: A (LEAVE A REPLY)

NEW QUESTION: 24In the EMU command line mode, different environmental monitoring units use differentcommand keywords for configuration. Which keyword is used by 4845/4875?A. DISB. POWERC. FAND. ESCAnswer: B (LEAVE A REPLY)

NEW QUESTION: 25Is the following description correct? The idea of the FTTx device offline deployment plan isto generate offline device configuration data through network planning dat a. After thedevice is installed and powered on, the configuration data is automatically issued toachieve the purpose of plug-and-play equipment.A. FalseB. TrueAnswer: B (LEAVE A REPLY)

NEW QUESTION: 26Is the following description correct? MxU automatic upgrade strategy, that is, when thedevice is powered on, the current version of the device is automatically compared with thetarget version of the strategy. If it is inconsistent, the device software version isautomatically upgraded to the target version.A. TrueB. FalseAnswer: A (LEAVE A REPLY)

NEW QUESTION: 27






Which of the following are not features of smart vlan?A. Smart VLAN is mainly used to distinguish users, each user has a VLAN.B. Under the same VLAN, the service flow between service virtual ports can be used forLayer 2 intercommunicationC. There are two types of ports: uplink port and service virtual portD. A Smart VLAN can contain multiple uplink ports and multiple service virtual portsAnswer: A,B (LEAVE A REPLY)

NEW QUESTION: 28What message does the H.248 media gateway send to the MGC for registration?A. AddB. RSIPC. SVC_CHG_REQD. NotifyAnswer: C (LEAVE A REPLY)

NEW QUESTION: 29What are the equipment maintenance methods currently not supported by MA5600T?A.WEBB. SNMPC. Serial portD. TELNETAnswer: A (LEAVE A REPLY)

NEW QUESTION: 30When testing the average transmit optical power of an optical interface, which of thefollowing descriptions are incorrect?A. The optical power meter is calibratedB. Connect one end of the test pigtail of the optical power meter to the "Rx" port of theoptical interface board, and connect the other end of the pigtail to the optical power meter.C. Repeat several times to check whether the maximum and minimum measured averagetransmit optical power meet the technical requirements.D. The optical fiber connector and the optical connector on the optical interface boardpanel are clean and well connectedAnswer: B (LEAVE A REPLY)

NEW QUESTION: 31Is the following description correct? MA5680T supports template mode and discreteconfiguration mode to configure FTTH services. In template mode configuration, use theont-profile add command to configure the ONT.A. False





B. TrueAnswer: A (LEAVE A REPLY)



NEW QUESTION: 32In the 802.1Q tag header, how many digits is the VLAN ID field, and how many VLANs canbe specified in total?A. 10;1024B. 4;16C. 12;4096D. 8;256Answer: C (LEAVE A REPLY)

NEW QUESTION: 33According to whether the UA2000 alarm is confirmed and cleared, what are its alarmstates?A. Confirmed but not clearedB. Confirmed and clearedC. Unconfirmed and clearedD. Unconfirmed and unclearedAnswer: A,B,C,D (LEAVE A REPLY)

NEW QUESTION: 34Is the following description correct? Computer network cardMACaddress isIETFUniformlyassigned to each manufacturer, the only one in the world.A. FalseB. TrueAnswer: (SHOW ANSWER)

NEW QUESTION: 35What is the next-generation development prospect of the access network?A. PromoteADSLTransmission distance, increase coverage radiusB. expandPSTNApplications






C. Light advances and retreatsD. Increase inADSLType of business transmitted onAnswer: C (LEAVE A REPLY)

NEW QUESTION: 36Is the following description correct? The Triple play in MA5600T supports single-PVC tripleplay and multiple-PVC triple play for xDSL access.A. FalseB. TrueAnswer: B (LEAVE A REPLY)

NEW QUESTION: 37Which of the following products does not belong to MDU?A. MA5612B. MA5620GC. MA5600TD. MA5616Answer: C (LEAVE A REPLY)

NEW QUESTION: 38What are the characteristics of ATM cells?A. The header is 5 bytesB. ATM cell is 53 bytes of fixed lengthC. The payload is 48 bytesD. Divided into letterhead and payloadAnswer: (SHOW ANSWER)

NEW QUESTION: 39Which one of the following descriptions of MA5616 is wrong?A. Support ADSL, VDSL, POTs accessB. Support 4 business slotsC. Uplink only supports GPON interfaceD. Support AC/DC inputAnswer: (SHOW ANSWER)

NEW QUESTION: 40Is the following description correct? In PON networks, multimode optical fibers are oftenused.A. TrueB. FalseAnswer: (SHOW ANSWER)







NEW QUESTION: 41What is the rated working voltage of the MA5600 equipment?A. -72B. -36C. -48D. -24Answer: C (LEAVE A REPLY)

NEW QUESTION: 42In the GPON system, what bandwidth types does type1 in the Tcont type include?A. Best effortB. Fixed bandwidthC. Non-guaranteed bandwidthD. Guaranteed bandwidthAnswer: B (LEAVE A REPLY)

NEW QUESTION: 43Which is the correct order of the loss size of the optical fiber connection point?A. Active connection> cold connection> weldingB. Active connection> fusion splicing> cold splicingC. Cold connection>Activity connection>WeldingD.Welding>Cold Splicing>Activity ConnectionAnswer: (SHOW ANSWER)

NEW QUESTION: 44What are the categories of acceptance test items in the MA5600T/MA5680T acceptancetest manual?A. Expansion Pack AB. Basic packageC. Expansion Pack BD. Premium packageAnswer: A,B,C (LEAVE A REPLY)

NEW QUESTION: 45onIPWhich statement is correct in terms of routing?A. Routing isOSIThe concept of the second layer in the model.B. Any route must include the following three parts of information: source address,destination address, and next hop.C. IPRouting is the guideIPPath information for packet forwarding.





D. In a local area network, routing includes the following two parts:IPAddressandMACaddress.Answer: (SHOW ANSWER)

NEW QUESTION: 46Which of the following descriptions about PPPoE is incorrect?A. The destination address of PADI is the broadcast address 0xffffffff, and the sourceaddress is the Ethernet address of the hostB. SESSION-ID identifies the value of a PPPOE sessionC. The entire discovery phase of PPPoE includes PADI, PADO, PADR, PADS, PADTD. PADT can be issued by the PC or BRAS at any time during the discovery phase toterminate the PPPoE dialogueAnswer: D (LEAVE A REPLY)



NEW QUESTION: 47Is the following description correct? The UA5000 and lanswitch are connected through GE,and the working mode of the ports on both sides can be auto-negotiation mode andmandatory mode.A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 48Regarding the MA5600T/MA5680T Ethernet access service board, which of the followingstatements is correct?A. None of the aboveB. Both H801ETHA and H801ETHB support Ethernet cascading and Ethernet uplinkC. H801ETHA supports Ethernet cascading and Ethernet uplinkD. H801ETHB supports Ethernet cascading and Ethernet uplinkAnswer: (SHOW ANSWER)

NEW QUESTION: 49






Which of the following statements about ATM network VP and VC is correct?A. A VP can include multiple VCs;B. A VC can include multiple VPs;C. There is no logical connection between VP and VC.D. VPI occupies the same number of bits in all cells, and the same is true for VCI;Answer: A (LEAVE A REPLY)

NEW QUESTION: 50Is the following description correct? TTLMainly to preventIPThe cyclic forwarding ofpackets in the network wastes network bandwidth.A. FalseB. TrueAnswer: (SHOW ANSWER)

NEW QUESTION: 51MA5600T provides various networking protection functions. Which of the followingprotection features is usually used for upstream port protection?A. Smart Link and Monitor Link featuresB. Ethernet link aggregationC. GPON Type B protectionD. GPON Type C protectionAnswer: A,B (LEAVE A REPLY)

NEW QUESTION: 52Is the following description correct? The simplified method of MA5600T/MA5680T GPONInternet service is optimized for the excessive number of templates and complicatedconfiguration in the template mode, reducing user configuration workload and subsequentmaintenance costs. The simplified mode currently only supports GPON FTTH scenarios.For newly-built GPON FTTH scenarios and scenarios that do not require high QoS, thesimplified mode can be used for service configuration.A. FalseB. TrueAnswer: B (LEAVE A REPLY)

NEW QUESTION: 53Which of the following products are not part of the ONU series?A. MA5652GB. HG8247C. MA5600TD. MA5612Answer: C (LEAVE A REPLY)






NEW QUESTION: 54Is the following description correct? VDSL2 provides uplink and downlinksymmetrical/asymmetrical transmission rates on a pair of twisted pairs. The transmissiondistance is about 3km. The maximum downlink rate is 52M (symmetrical rate) and themaximum uplink rate is 12M (asymmetrical rate).A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 55Is the following description correct? LANThe transmission form is generally bus-based, andthe most commonly used corresponding protocols are carrier sensing and collisiondetectionCSMA/CDprotocol.A. TrueB. FalseAnswer: A (LEAVE A REPLY)

NEW QUESTION: 56What is the number of ADSL2+ subbands?A. 128B. 256C. 512D. 384Answer: C (LEAVE A REPLY)

NEW QUESTION: 57In GPON network, which of the following reasons may cause ONU to fail to go online?A. The optical power received by the ONU is greater than the overload optical power.B. There is abnormal attenuation on the ODN line.C. The optical power received by the ONU is less than the sensitivity valueD. The ODN line is too long and exceeds the online distance set by the system.Answer: A,B,C,D (LEAVE A REPLY)

NEW QUESTION: 58command... What is the correct description of the three points in ./.profile?A. The third point. Connected to the previous /, which means the root directoryB. The second point. Connected to the back /, ./ indicates the current directoryC. The first point. Means execution, same as shD. The third point. Before profile, the entire .profile is a file name, which means a hiddenfile





Answer: B,C,D (LEAVE A REPLY)

NEW QUESTION: 59Is the following description correct? In the GPON network, in order to avoid data conflictsand improve network utilization efficiency, the downstream direction adopts TDMA multipleaccess mode and arbitrates the data transmission of each ONU.A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 60In the UA5000 chassis with PVM as the main control board, which statement about theuser board is correct?A. If it is an A32 board, it needs to be added manually, if it is an ASL board, it isautomatically discoveredB. Must be added manuallyC. Automatic discoveryD. If it is an ASL board, it needs to be added manually, if it is an A32 board, it isautomatically discoveredAnswer: B (LEAVE A REPLY)

NEW QUESTION: 61Which of the following descriptions about the MA5680T GPBD board is wrong?A. Support maximum 1:64 splitting ratio.B. Support high temperature automatic shutdownC. Support Class B+ and Class C+ optical modules.D. Support 8 GPON SFP portsAnswer: A (LEAVE A REPLY)



NEW QUESTION: 62According to the H.248 protocol, what is the type of terminal occupied when the telephoneterminal is off-hook?






A. Permanent terminalB. Temporary terminalC. Semi-permanent terminalD. Persistent TerminalAnswer: C (LEAVE A REPLY)

NEW QUESTION: 63According to the ITU-T G.984.x series of standards, what are the upstream anddownstream bandwidths of GPON?A. 2.5Gbps/1.25GbpsB. 2.5Gbps/2.5GbpsC. 1.25Gbps/2.5GbpsD. 1.25Gbps/1.25GbpsAnswer: C (LEAVE A REPLY)

NEW QUESTION: 64When MA5600T is newly launched and connected to the network management system,which of the following descriptions are correct?A. The configuration of read community name and write community name is the same asthat on the network management side.B. Add a static route, the destination address is the network segment where the networkmanagement IP is locatedC. The configuration of the SNMP version should be the same as the configuration on theU2000 sideD. The interface IP address of the MA5600T used for management must be in the samenetwork segment as the network management IP addressAnswer: (SHOW ANSWER)

NEW QUESTION: 65Which of the following isql login database commands is correct?A. isql -Usa -Ssa_password -SN2000DBServerB. isql -Usa -Psa_password -SN2000DBServerC. isql -Usa_password -Ssa -PN2000DBServerD. isql -Usa -PN2000DBServer -Ssa_passwordAnswer: (SHOW ANSWER)

NEW QUESTION: 66What is the correct correspondence between IP address and MAC address in a broadcastdomain?A. None of the aboveB. One IP address can correspond to multiple MAC addresses





C. One MAC address can only correspond to one IP addressD. One MAC address can correspond to multiple IP addressesAnswer: D (LEAVE A REPLY)

NEW QUESTION: 67Is the following description correct? In the routing table entries, for the same destinationaddress and mask (Destination/Mask), can only correspond to the only next hop andoutgoing interface(Nexthop/Interface).A. TrueB. FalseAnswer: (SHOW ANSWER)

NEW QUESTION: 68PVM packet voice processing board, which manages and controls the narrowband userboard in the UA5000 chassis. What are its main functions?A. Support the encapsulation of TDM voice into IP packets upstream to the softswitchequipmentB. Realize V5 protocol and H.248/MGCP protocol processingC. Support the TDM voice signal upstream to the switch through the V5 interfaceD. Support encapsulating TDM voice into ATM cell upstream to softswitch equipmentAnswer: A,B,C (LEAVE A REPLY)

NEW QUESTION: 69MA5680T supports QinQ and VLAN stacking attributes. Which of the following VLANssupports QinQ attributes?A. sub vlanB. super vlanC. smart vlanD. Common vlanAnswer: (SHOW ANSWER)

NEW QUESTION: 70QA engineers start the SmartKit NSE2700 Quality Inspector tool, which of the followingmethods can be supported to connect devices?A. SSH wayB. Telnet methodC. Multi-hop methodD. Serial port modeAnswer: A,B,C,D (LEAVE A REPLY)

NEW QUESTION: 71






Is the following description correct? G.SHDSL broadband access technology is suitable forhigh-speed Internet access and video conferencing for users in hotels and Internet cafes,but it cannot provide dedicated line interconnection and dedicated line access.A. FalseB. TrueAnswer: A (LEAVE A REPLY)

NEW QUESTION: 72Which of the following are the most common services that belong to triple play access?A. IPTV businessB. Internet access businessC. Dedicated line businessD. VoIP businessAnswer: A,B,D (LEAVE A REPLY)

NEW QUESTION: 73Which of the following descriptions about DHCP is incorrect?A. The message interaction experienced by DHCP to obtain an address normally includesDiscover, Offer, Request, ACKB. Multiple DHCP servers are not allowed in the network at the same time, becausemultiple servers will respond at the same time, and the client cannot select an addressC. The Discover message between the DHCP Relay and the DHCP server is a unicastmessageD. If the client abandons the current IP address, she uses a DHCP RELEASE message tonotify the server, and the server reclaims this address for next use.Answer: B (LEAVE A REPLY)

NEW QUESTION: 74The international professional organization responsible for allocating IP addresses hasdivided several network segments as private network segments, which can be freelydistributed and used by people on private networks. Which of the following is not a networksegment of private addresses?A. 172.16.0.0/16B. 224.0.0.0/8C. 10.0.0.0/8D. 192.168.0.0/16Answer: B (LEAVE A REPLY)

NEW QUESTION: 75Regarding the ATM network, which one of the following descriptions is wrong?A. Can guarantee the quality of service performance index (QOS) of various businesses





B.Working in the network layer of the OSI modelC. Reduce the processing time of intermediate nodes and support high-speed transmissionD. Support fixed-length exchangeAnswer: B (LEAVE A REPLY)

NEW QUESTION: 76Which of the following is not an ONT product?A. HG8010B. HG8247C. HG510VD. HG8245Answer: C (LEAVE A REPLY)



NEW QUESTION: 77When the UA5000 is configured with the H.248 protocol to connect to the softswitch, whichof the following parameters must be consistent at both ends?A. Transport layer protocol typeB. MG interface description informationC. Transport layer protocol port numberD. Coding methodAnswer: (SHOW ANSWER)

NEW QUESTION: 78Is the following description correct? The MA5600T SCUN board provides 1 maintenancenetwork port, 1 serial port, 1 environmental monitoring port, and 8 GE ports.A. FalseB. TrueAnswer: A (LEAVE A REPLY)

NEW QUESTION: 79






When other SNMP parameters are configured correctly, how to configure the trap sourceaddress of the device to ensure that the network manager can receive device alarmsnormally?A. All of the above.B. The trap source address is set to 127.0.0.1C. The trap source address is set to the loopback addressD. The trap source address is set to the address used by the network manager to add thedeviceAnswer: D (LEAVE A REPLY)

NEW QUESTION: 80What is the difference between alarm shielding and alarm suppression?A.When the alarm shielding function is set, the network element will no longer report thealarm; when the alarm suppression is set, the network element will still report the alarm,but the network manager will not receive it.B.When setting the alarm shielding function, the network element does any processing.C.When setting the alarm shielding function, the network element will still report the alarm,but the network management will not receive it; when the alarm suppression is set, thenetwork element will no longer report the alarmD. There is no differenceAnswer: (SHOW ANSWER)

NEW QUESTION: 81In the EPON network, what are the management protocols running between the OLT andthe ONT?A. OMCIB. SNMPC. OAMD. IGMPAnswer: C (LEAVE A REPLY)

NEW QUESTION: 82Is the following description correct? In EPON, when the fiber length under the PON port is10KM, the recommended splitting ratio is 1:32; when the fiber length is 20KM, therecommended splitting ratio is 1:16.A. TrueB. FalseAnswer: A (LEAVE A REPLY)

NEW QUESTION: 83





Which of the following commands is used to query whether all the boards in theMA5600T/MA5680T 0 frame are operating normally?A. display frame info 0/0B. display board info 0C. display frame info 0D. display board 0Answer: (SHOW ANSWER)

NEW QUESTION: 84Is the following description correct? When the ONT is offline, the MA5600T/MA5680T canperform ONT PPPoE simulation test operations.A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 85What are the incorrect statements about Type B protection for GPON networks?A. Switching trigger conditions: 1) branch fiber failure, 2) OLT single board failure, 3)component failureB. Service configuration data only needs to be configured to the main port, no need toconfigure two copiesC. Support OLT inter-board and intra-board port combination protection pairD. Protection based on PON port and backbone fiberAnswer: (SHOW ANSWER)

NEW QUESTION: 86In Ethernet, what address is used to distinguish different devices?A. MACaddressB. LLCaddressC. IPXaddressD. IPaddressAnswer: A (LEAVE A REPLY)

NEW QUESTION: 87In the MA5600 software system, which VLAN can only add Ethernet ports?A. Mux VLANB. Super VLANC. Smart VLAND. Standard VLANAnswer: (SHOW ANSWER)






NEW QUESTION: 88In the EPON network, which parameter is used to filter the downstream data on the ONU?A. ALLOC IDB. LLIDC. GEM-PORT IDD. ONT IDAnswer: B (LEAVE A REPLY)

NEW QUESTION: 89In the EPON network, what is the upstream and downstream bandwidth of the PON port?A. 1.25Gpbs/1.25GpbsB. 1.25bps/2.5GbpsC. 1Gbps/2GbpsD. 1Gbps/1GbpsAnswer: A (LEAVE A REPLY)

NEW QUESTION: 90Is the following description correct? ICMPIs a link layer protocol,ICMPThe message istriggered by the physical layer, and then byIPLayer or higher layer protocol to respond.A. FalseB. TrueAnswer: A (LEAVE A REPLY)

NEW QUESTION: 91Is the following description correct? The single board program package file released byMA5680T contains all the supported single board software. In actual use, there is no needto use so much single board software. Therefore, you can open a small package throughthe unpacking tool to improve the upgrade efficiency.A. TrueB. FalseAnswer: A (LEAVE A REPLY)








NEW QUESTION: 921518 byte Ethernet data message is converted into ATM cells for transmission through1483 b format encapsulation, how many ATM cells will be converted into?A. 32B. 29C. 28D. 27Answer: A (LEAVE A REPLY)

NEW QUESTION: 93Is the following description correct? Users can establish PVC connections betweendifferent board ports or between different ports on the same board. The main purpose is torealize the point-to-point interconnection between two different users.A. FalseB. TrueAnswer: (SHOW ANSWER)

NEW QUESTION: 94Which of the following methods can be used for the reset test of the MA5600T/MA5680Tsingle board?A. Press the RESET button on the handle bar of the main control board to forcibly resetthe main control board. Observe whether the main control board can return to normal afterresetting.B. All of the aboveC. Use the command board reset to reset the service board. Check whether the serviceboard can be restored to normal after resetting.D. Hot-swappable the board, check whether the board can be restored to normal afterresetAnswer: B (LEAVE A REPLY)

NEW QUESTION: 95Is the following description correct? The ADSL G.992.1 or G.dmt standard is a technicalspecification that does not require a signal splitter.A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 96In the template mode of MA5680T, where is the configuration of tcont and gemportintegrated?A. ont-profile





B. ont-lineprofileC. ont-srvprofileD. dba-profileAnswer: (SHOW ANSWER)

NEW QUESTION: 97Regarding super vlan, which of the following statements are correct?A. Super VLAN corresponds to a routing interfaceB. The main purpose of Super VLAN is to save IP addresses.C. Super VLAN aggregates multiple Sub VLANsD. Sub VLAN uses Super VLAN togetherAnswer: (SHOW ANSWER)

NEW QUESTION: 98Compared with the template mode, when the MA5600T configures FTTH services in asimplified manner, which of the following steps does not require configuration?A. Configure the line templateB. Configure the DBA templateC. Configure traffic templateD. Configure business templatesAnswer: (SHOW ANSWER)

NEW QUESTION: 99When configuring traffic table for MA5680T, if only CIR is configured and PIR parametersare not specified, what is the PIR value by default?A. NothingB. PIR=min(2*cir, 10240000)C. PIR=min(1.5*cir, 10240000)D. PIR=CIRAnswer: B (LEAVE A REPLY)

NEW QUESTION: 100Is the following description correct? In the EPON network, in order to avoid data conflictsand improve network utilization efficiency, the downstream direction adopts TDMA multipleaccess mode and arbitrates the data transmission of each ONU.A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 101






Is the following description correct? Can test engineers use SmartKit NSE2700 Inspectoron site to improve the efficiency of ADSL port activation?A. TrueB. FalseAnswer: B (LEAVE A REPLY)

NEW QUESTION: 102When the MA5600 service box provides pure broadband service, how many slots can beinserted into the service board?A. 16B. 18C. 12D. 14Answer: D (LEAVE A REPLY)

NEW QUESTION: 10310BASE-TRefers to which medium is defined?A. Thin coaxial cableB. Twisted pairC. Thick coaxial cableD. optical fiberAnswer: B (LEAVE A REPLY)

NEW QUESTION: 104IPA part of the fields in the message are specifically used to describe the life cycle of themessage, namelyTTLValue, what is its maximum value?A. 1024B. 255C. 1023D. 256Answer: (SHOW ANSWER)

NEW QUESTION: 105If there are multiple set-top boxes under an ONT (for example: HG850) watching amulticast program at the same time, which of the following functions can be enabled on theOLT for the ONT multicast user to ensure that when one set-top box switches channels,other set-top boxes The programs you watch are not affected?A. previewB. Fast departure based on MACC. immediate leaveD. prejoin





Answer: B (LEAVE A REPLY)





Documents

Huawei.H35-210 V2.5.v2021-09-23