IC-7200 Manual

8/7/2019 IC-7200 Manual

1/104

INSTRUCTION MANUAL

HF/50 MHz TRANSCEIVER

i7200

8/7/2019 IC-7200 Manual

2/104

IMPORTANT

READ THIS INSTRUCTION MANUALCAREFULLYbeore attempting to operate thetransceiver.

SAVE THIS INSTRUCTION MANUAL. Thismanual contains important saety and operating in-structions or the IC-7200.

FOREWORD

We understand that you have a choice o many dier-ent radios in the market place. We want to take a cou-

ple o moments o your time to thank you or makingthe IC-7200 your radio o choice, and hope you agreewith Icoms philosophy o technology irst. Manyhours o research and development went into the de-sign o your IC-7200.

DFEATURES

IF DSP features Digital Twin PBT Manual notch function 0.5 ppm of high frequency stability Simple operation Tough and compact body Standard voice synthesizer

EXPLICIT DEFINITIONS

WORD DEFINITION

RWARNINGPersonal injury, ire hazard or electric

shock may occur.CAUTION Equipment damage may occur.

NOTEI disregarded, inconvenience only. No risk

o personal injury, fre or electric shock.

SUPPLIED ACCESSORIES

The transceiver comes with the ollowing accessories.

Qty.qHand microphone (HM-36) ............................. 1wDC power cable (OPC-1457) .......................... 1eSpare use (ATC 5 A) ...................................... 1rSpare use (ATC 30 A) .................................... 2t ACC cable ......................................................... 1y 3.5 (d) mm plug ................................................. 1u 6.3 (d) mm Electronic keyer plug ...................... 1

i Microphone hanger ........................................... 1

o Jack cap (or [PHONES]) ................................. 1

q

e

t

w

y u

r

i o

FCC INFORMATION

FOR CLASS B UNINTENTIONAL RADIATORS:This equipment has been tested and ound to complywith the limits or a Class B digital device, pursuant topart 15 o the FCC Rules. These limits are designedto provide reasonable protection against harmul in-tererence in a residential installation. This equipmentgenerates, uses and can radiate radio requency en-ergy and, i not installed and used in accordance withthe instructions, may cause harmul intererence to

radio communications. However, there is no guaran-tee that intererence will not occur in a particular in-stallation. I this equipment does cause harmul inter-erence to radio or television reception, which can bedetermined by turning the equipment o and on, theuser is encouraged to try to correct the intererenceby one or more o the ollowing measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment

and receiver. Connect the equipment into an outlet on a circuit

dierent rom that to which the receiver is con-nected. Consult the dealer or an experienced radio/TV

technician or help.

Icom, Icom Inc. and the logo are registered trademarks oIcom Incorporated (Japan) in the United States, the United King-

dom, Germany, France, Spain, Russia and/or other countries.Microsot, Windows and Windows Vista are either registered trade-

marks or trademarks o Microsot Corporation in the United States

and/or other countries.

All other products or brands are registered trademarks or trade-

marks o their respective holders.

i

8/7/2019 IC-7200 Manual

3/104

PRECAUTIONS

RWARNING RF EXPOSURE! This device emitsRadio Frequency (RF) energy. Extreme caution

should be observed when operating this device. Iyou have any questions regarding RF exposure andsaety standards please reer to the Federal Com-munications Commission Oice o Engineering andTechnologys report on Evaluating Compliance withFCC Guidelines or Human Radio Frequency Electro-magnetic Fields (OET Bulletin 65).

RWARNING HIGH VOLTAGE! NEVER touch anantenna or internal antenna connector during trans-mission. This may result in an electrical shock or burn.

RWARNING! NEVER operate the transceiverwhile driving a vehicle. Sae driving requires your ullattentionanything less may result in an accident.

RNEVER apply AC power to the [DC13.8V] socketon the transceiver rear panel. This could cause a reor damage the transceiver.

RNEVER apply more than 16 V DC, such as a 24 Vbattery, to the [DC13.8V] socket on the transceiverrear panel. This could cause a ire or damage thetransceiver.

RNEVER let metal, wire or other objects touch anyinternal part or connectors on the rear panel o thetransceiver. This may result in an electric shock or thiscould cause a re or damege the transceiver.

RNEVER expose the transceiver to rain, snow orany liquids.

DO NOT use or place the transceiver in areas withtemperatures below 10C (+14F) or above +60C(+140F). Be aware that temperatures on a vehiclesdashboard can exceed +80C (+176F), resulting in

permanent damage to the transceiver i let there orextended periods.

DO NOT place the transceiver in excessively dustyenvironments or in direct sunlight.

DO NOT place the transceiver against walls or putanything on top o the transceiver. This will obstructheat dissipation.

Place unit in a secure place to avoid inadvertent useby children.

During mobile operation, NEVER place the trans-ceiver where air bag deployment may be obstructed.

During mobile operation, DO NOT place the trans-

ceiver where hot or cold air blows directly onto it.

During mobile operation, DO NOT operate the trans-ceiver without running the vehicles engine. When thetransceivers power is ON and your vehicles engineis OFF, the vehicles battery will quickly become ex-hausted.

Make sure the transceiver power is OFF beore start-ing the vehicle engine. This will avoid possible dam-age to the transceiver by ignition voltage spikes.

During maritime mobile operation, keep the trans-ceiver and microphone as ar away as possible romthe magnetic navigation compass to prevent errone-ous indications.

BE CAREFUL! The rear panel will become hot whenoperating the transceiver continuously or long peri-ods.

BE CAREFUL! I a linear ampliier is connected, setthe transceivers RF output power to less than thelinear ampliers maximum input level, otherwise, thelinear amplier will be damaged.

Use Icom microphones only (supplied or optional).Other manuacturers microphones have dierent pinassignments, and connection to the IC-7200 maydamage the transceiver.

For U.S.A. onlyCaution: Changes or modiications to this trans-ceiver, not expressly approved by Icom Inc., couldvoid your authority to operate this transceiver underFCC regulations.

ii

8/7/2019 IC-7200 Manual

4/104

iii

TABLE OF CONTENTS

IMPORTANT............................................................... i

FOREWORD .............................................................. iEXPLICIT DEFINITIONS............................................ i

SUPPLIED ACCESSORIES....................................... i

FCC INFORMATION .................................................. i

PRECAUTIONS......................................................... ii

TABLE OF CONTENTS ....................................... iii-iv

1 PANEL DESCRIPTION................................... 111

Front panel ........................................................ 1

D Keypad .......................................................... 5

Function display ................................................ 7

Rear panel ......................................................... 9

D ACC socket inormation .............................. 10 Microphones .................................................... 11

D HM-36 ......................................................... 11

D SM-20 ......................................................... 11

2 INSTALLATION AND CONNECTIONS ........ 1220

Unpacking ....................................................... 12

Selecting a location ......................................... 12

Grounding ....................................................... 12

Antenna connection ........................................ 12

Required connections...................................... 13

Advanced connections .................................... 14

Power supply connections ............................... 15

Connecting the DC Power Supply ................... 15

Battery connections ......................................... 15

External antenna tuners .................................. 16

Linear amplier connections............................ 17

Connections or CW ........................................ 18

Connections or RTTY ..................................... 19

D Connections or RTTY (FSK) ...................... 19

D Connections or RTTY (AFSK) .................... 19

Connections or SSTV or PSK31 .................... 20

DWhen connecting to the [ACC] socket ......... 20

DWhen connecting to the [MIC] connector .... 20 DWhen connecting to the [USB] jack ............. 20

3 BASIC OPERATION ..................................... 2132

Beore rst applying power .............................. 21

Applying power (CPU resetting) ...................... 21

VFO description ............................................... 22

VFO operation ................................................. 22

D Selecting the VFO A/B ................................ 22

D VFO equalization......................................... 22

Selecting VFO/memory mode ......................... 23

D Dierences between VFO mode and

memory mode ............................................. 23

Selecting an operating band ........................... 24

D Using the band stacking register ................. 24 Frequency setting ............................................ 25

D Using the main dial ..................................... 25

D Direct requency entry with keypad ............. 25

D Programmable tuning steps ........................ 26

D Selecting the programmable tuning step..... 26

D 1 Hz and 10 Hz tuning steps ....................... 27

D TS switch fow chart ................................. 27

D Auto tuning step unction ............................ 28

D tuning unction

(SSB data/CW/RTTY only) ......................... 28

DBand edge warning beep ............................ 28 Volume setting ................................................. 29

Operating mode selection ............................... 29

Dial lock unction ............................................. 29

RF gain and Squelch ....................................... 30

Meter unction ................................................. 30

Basic transmit operation .................................. 31

D Transmitting ................................................. 31

DOutput power and Microphone gain settings... 31

Voice synthesizer unction ............................... 32

4 RECEIVE AND TRANSMIT .......................... 3343

Operating SSB ................................................ 33 D Convenient unctions or receive ................. 33

D Convenient unctions or transmit ................ 34

D About 5 MHz band operation

(USA version only) ...................................... 34

Operating CW ................................................. 35

D Convenient unctions or receive ................. 36


D CW reverse mode ....................................... 37

D CW pitch control.......................................... 37

D CW side tone unction ................................. 38

D Keying speed setting ................................... 38

Operating RTTY (FSK) .................................... 39


D RTTY reverse mode .................................... 40

D Twin peak lter ............................................ 40

D RTTY decode set mode .............................. 41

Operating AM .................................................. 42



Data mode (SSTV/PSK31) operation .............. 43

8/7/2019 IC-7200 Manual

5/104

5 FUNCTIONS FOR RECEIVE ........................ 4452

RIT unction ..................................................... 44 Preamp and attenuator ................................... 45

AGC unction ................................................... 45

D AGC time constant selection ....................... 45

Twin PBT operation ......................................... 46

IF lter selection .............................................. 47

D IF lter selection .......................................... 47

D FIlter passband width setting ...................... 48

D IF Ilter shape (SSB/CW only) ..................... 48

Noise blanker .................................................. 49

D Noise blanker settings ................................. 49

Noise reduction ............................................... 50

D Noise reduction level setting ....................... 50

Notch unction ................................................. 51

D Auto notch unction ..................................... 51

D Manual notch unction ................................. 51

D Manual notch lter setting ........................... 52

6 FUNCTIONS FOR TRANSMIT ..................... 5360

VOX unction.................................................... 53

D Adjusting the VOX unction.......................... 53

D VOX set mode ............................................. 54

Break-in unction ............................................. 55

D Semi break-in operation .............................. 55 D Full break-in operation ................................ 56

Speech compressor ........................................ 57

D Compression level setting ........................... 57

Split requency operation ................................ 58

D Quick split unction ...................................... 59

D Split lock unction ........................................ 59

Measuring SWR .............................................. 60

7 MEMORY OPERATION ................................ 6164

Memory channels ............................................ 61

Memory channel selection .............................. 61

Memory programming ..................................... 62 D Programming in VFO mode ........................ 62

D Programming in memory mode...................62

Frequency copying .......................................... 63

D Copying in memory mode ........................... 63

Memory clearing ............................................. 64

8 SCAN OPERATION ...................................... 6566

Scan types ...................................................... 65

Preparation ...................................................... 65

Programmed scan operation (VFO mode) ...... 66

Memory scan operation (Memory mode) ........66

9 ANTENNA TUNER OPERATION ................. 6769

Optional AT-180 automaticantennatuneroperation ......................................................... 67

D Tuner operation ........................................... 67

D Manual tuning ............................................. 67

AT-180 internal switch description ................... 68

Optional AH-4 automaticantennatuner

operation ......................................................... 69

D AH-4 operation ............................................ 69

10 SET MODE ................................................... 7082

General ........................................................... 70

D Quick set mode operation ........................... 70

D Set mode operation ..................................... 70 Quick set mode ............................................... 71

Set mode ......................................................... 74

D Paddle operation rom [MIC] connector ...... 82

11 MAINTENANCE ........................................... 8384

Fuse replacement ........................................... 83

D DC power cable use replacement .............. 83

D Circuitry use replacement .......................... 83

Memory backup ............................................... 84

Resetting the CPU .......................................... 84

Cleaning .......................................................... 84

12 TROUBLESHOOTING .................................. 8586

13 OPTION INSTALLATIONS ................................. 87

MB-116 handles installation ........................... 87

MB-117 carryinghandle installation ............. 87

MB-118 mobilemountingbracketinstallation..87

14 CONTROL COMMAND ................................ 8891

Remote jack (CI-V) inormation ....................... 88

D CI-V connection example ............................ 88

D Data ormat ................................................. 88

D Command table ........................................... 89 D Band stacking register ................................ 91

D Data mode with lter width setting .............. 91

15 SPECIFICATIONS .............................................. 92

General ........................................................... 92

Transmitter ....................................................... 92

Receiver .......................................................... 92

16 OPTIONS ...................................................... 9394

17 ABOUT CE ................................................... 9596

18 BAND VOLTAGE MODIFICATION...................... 97 Band voltage modication ............................... 97

iv

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

8/7/2019 IC-7200 Manual

6/104

qPASSBAND TUNING CONTROLS [TWIN PBT]Adjust the receivers DSP ilter passband width.(p. 46) The limit o the variable range depends on the pass-

band width and mode. The limit o the variable range

is hal o the passband width, and PBT is adjustable in200 Hz (AM) or 50 Hz (other models) steps.

Rotate both [TWIN PBT] controls (PBT1 and PBT2) to

the same position shits the IF.

4What is the PBT control?Generally, the PBT electronically narrows the IFpassband width to reject intererence. This trans-ceiver uses the DSP circuit or the PBT unction.

PBT2

PBT1

Low cutHigh cut Center

TWIN PBT TWIN PBT TWIN PBT

+

wNOISE BLANKER KEY NB (p. 49) Push to turn the noise blanker unction ON or

OFF.

appears on the display.

Push and hold or 1 sec to enter the noise

blanker set mode or setting the noise blankerlevel and blank time; push again to return to nor-mal operation. When entering the noise blanker set mode, the noise

blanker unction is automatically turned ON.

4What is the noise blanker?The noise blanker reduces pulse-type noise suchas that generated by automobile ignition systems.This unction is not eective against non pulse-typenoise.

eNR KEY NR (p. 50) Push to turn the noise reduction unction ON orOFF.


Push and hold or 1 sec. to enter the noise re-duction level set mode; push again to return tonormal operation. When entering the noise reduction set mode, the

noise reduction unction is automatically turned ON.

4What is the Noise Reduction function?The Noise Reduction (NR) unction removes ran-dom noise rom the receiver passband. The level is

adjustable to allow maximum clarity without harm-ing the intelligibility o the desired signal. Noise Re-duction should generally not be used with digitalmodes.

1

1

PANEL DESCRIPTION

i7200

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENTBANDGENE

9

.

AGCMW

AN FMETERNRNB

Speakertrew

FunctionDisplay (p. 7)

ui y

q

o

Front panel

8/7/2019 IC-7200 Manual

7/104

8/7/2019 IC-7200 Manual

8/104

3

!0MODE KEY MODE (p. 29) Push momentarily to cycle through the operating

modes:USB/LSB CW/CW-R RTTY/RTTY-R AM

Push and hold or 1 sec. to toggle the ollowing

operating modes:USB LSB (p. 33)CW CW-R (Reverse) (p. 35)RTTY RTTY-R (Reverse) (p. 39) CW-R or RTTY-R appears on the display when

reverse mode is selected.

Undesired modes can be inhibited in set mode.(p. 81)

!1TUNING STEP KEY TS (pgs. 26, 27) Push to turn the programmable tuning step ON

or OFF.

appears above the 1 kHz indicator when the pro-grammable tuning step is turned ON and the re-

quency can be changed in programmed kHz steps.

While the programmable tuning step is turnedON ( appears), push and hold or 1 sec. toenter tuning step set mode; push again to returnto normal operation. 0.1, 1, 5, 9 and 10 kHz programmable tuning steps

are available.

While the programmable tuning step is turnedOFF, push and hold or 1 sec. to turn the 1 Hzstep ON and OFF. 1 Hz indication appears, and the requency can be

changed in 1 Hz steps.

!2PREAMP/ATTENUATOR KEYP.AMP

ATT (p. 45) Push to turn the preamp ON or OFF.


Push and hold or 1 sec. to turn the 20 dB atten-uator ON; push momentarily to turn the attenua-

tor OFF. appears on the display.

4What is the preamp?The preamp ampliies signals in the receiver rontend (input) circuit to improve the sensitivity. Turnthe preamp ON when receiving weak signals.

4What is the attenuator?The attenuator prevents a strong undesired signalnear the desired requency or near your location,such as rom a broadcast station, rom causing dis-tortion or spurious signals.

!3MAIN DIAL [DIAL]Changes the displayed requency and selects val-ues or selected set mode items, etc.

!4FILTER KEY FILTER (p. 47) Push momentarily to cycle the IF ilter settings

between wide, middle and narrow or the se-lected operating mode.

Push and hold or 1 sec. to enter the ilter setmode.

i7200

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENTBANDGENE

9

.

AGCMW

AN FMETERNRNB

SpeakerFunctionDisplay (p. 7)

!3@1 !5 !4!6!7!9 !8@0

!1!0

!2

Front panel (Continued)

1 PANEL DESCRIPTION

8/7/2019 IC-7200 Manual

9/104

4

1PANEL DESCRIPTION

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

!5SPCHLOCK KEYSPCH

Push to announce the selected requency and

S-meter level by the speech synthesizer. (p. 32) The parameters to be announced can be selected in

the set mode. (p. 77)

Push and hold or 1 sec. to turn the dial lockunction ON or OFF. (p. 29)

The dial lock unction electronically locks the main

dial.

appears while the dial lock unction is ON.

!6POWER KEY Push to turn power ON.

Turn the DC power supply ON in advance.

Push and hold or 1 sec. to turn power OFF.

!7TUNER KEY TUNER (p. 67) Push to turn the automatic antenna tuner unc-

tion ON or OFF. An optional antenna tuner must be connected.


Push and hold or 1 sec. to manually tune theantenna tuner. An optional antenna tuner must be connected.

When the tuner cannot tune the antenna, the tuning

circuit is bypassed automatically ater 20 sec.

!8RF GAIN/SQUELCH CONTROL[RF/SQL](outer control; p. 30) Adjusts the RF gain and squelch threshold level.

The squelch removes noise output rom thespeaker (closed condition) when no signal is re-ceived. The squelch is available or all modes.

The control can be set as the squelch plus RF gaincontrols, squelch control only (RF gain is ixed at

maximum) or Auto (RF gain control in SSB, CW and

RTTY; squelch control in AM) in set mode.

MODESET MODE SETTING

AUTO SQL RF + SQL

SSB, CW

RTTYRF GAIN SQL RF GAIN + SQL

AM SQL SQL RF GAIN + SQL

Minimum RF gain

Adjustable range

RF gain adjustable

range

Maximum RF gain

Maximum RF gain

Squelch is open. S-meter squelch

S-meter squelch

threshold

Lowest threshold Highest threshold

Squelch is open.

S-meter squelch

S-meter squelch

threshold

When functioning as RF GAIN/SQL control

When functioning as RF GAIN control(Squelch is fixed open; SSB, CW, RTTY only)

When functioning as SQL control(RF gain is fixed at maximum.)

!9AF CONTROL [AF] (inner control; p. 29)Varies the audio output level rom the speaker.

Audio output

decreases

Audio output

increases

@0HEADPHONE JACK [PHONES]Accepts headphones with 816 impedance. Output power: 5 mW with an 8 load.

When headphones are connected, no receive audiocomes rom the speaker.

@1MICROPHONE CONNECTOR [MIC]Accepts supplied or optional microphone. See p. 11 or appropriate microphones and microphone

connector inormation.

8/7/2019 IC-7200 Manual

10/104

8/7/2019 IC-7200 Manual

11/104

8/7/2019 IC-7200 Manual

12/104

7

q TRANSMIT INDICATORAppears while transmitting.

w MODE INDICATORSShows the selected operating mode. appears when SSB/AM data mode is se-

lected. (p. 71)

-R appears when CW reverse or RTTY reversemode is selected. (pgs. 29, 35, 39)

e IF FILTER INDICATORS (p. 47)Shows the selected IF lter.

appears when the wide IF lter is selected.

appears when the normal IF ilter is se-lected.

appears when the narrow IF ilter is se-lected.

r LOCK INDICATOR (p. 29)Appears when the dial lock unction is activated.

t MEMORY INDICATOR (p. 61)

Appears when memory mode is selected.

y MEMORY CHANNEL NUMBER READOUT(p. 61)Shows the selected memory channel number.

u BLANK INDICATOR (p. 62)Appears when the selected memory channel isblank.

This indicator appears both in VFO and memory mode.

i SIGNAL/SQL/RF-GAIN METER Shows receiving signal strength while receiving.

Shows either transmit power meter (Po), SWRor ALC while transmitting. (p. 30)

o NOTCH INDICATORS (p. 51) appears when the automatic notch unc-

tion is activated. appears when the manual notch unction

is activated.

!0 NOISE REDUCTION INDICATOR (p. 50)Appears when the noise reduction is activated.

!1 NOISE BLANKER INDICATOR (p. 49)Appears when the noise blanker is activated.

!2 TUNE INDICATOR (p. 67) Appears when the optional automatic antenna

tuner is activated. Blinks while tuning.

!3 RECEIVE INDICATORAppears while receiving a signal or when thesquelch is open.

!4 FREQUENCY READOUTShows the operating requency.

Function display

q w e r

t

i

u

y

!1 o!0

!2

!3

!4

1 PANEL DESCRIPTION

8/7/2019 IC-7200 Manual

13/104

8

1PANEL DESCRIPTION

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

!5 PROGRAMMABLE TUNING STEP INDICATOR Appears when the programmable tuning step is

selected. (p. 26)

!6 RIT INDICATOR (p. 44)Appears when the RIT unction is activated.

!7 VFO INDICATORS (p. 22)VFO A or VFO B appears when VFO mode isselected.

!8 FUNCTION INDICATORS appears when the speech compressor

is activated in SSB mode. appears when the VOX unction is acti-

vated. appears during split requency opera-

tion. appears when preamp is activated. appears when the attenuator unction is

activated. appears during scan.

Blinks when scan is paused.

!9 AGC INDICATORS (p. 45)Shows the selected AGC time constant. F.AGC or AGC ast; AGC-OFF or AGC OFF; no in-

dicator; or AGC slow.

@0BREAK-IN INDICATORS (p. 55) BK appears when the semi break-in unction is

activated. F-BK appears when the ull break-in unction

is activated.

!5 !6

!7

!8

!9

@0

8/7/2019 IC-7200 Manual

14/104

8/7/2019 IC-7200 Manual

15/104

8/7/2019 IC-7200 Manual

16/104

11

MICROPHONE CONNECTOR

(Front view)

y GND (PTT ground)

t PTT

r Squelch switch

q Microphone input

w +8 V DC output

e Frequency up/down

i AF output(varies with [AF])

u GND(Microphone ground)

[MIC]

PIN NO.FUNCTION DESCRIPTION

w +8 V DC output Max. 10 mA

eFrequency up Ground

Frequency down Ground through 470

rSquelch open LOW level

Squelch close HIGH level

CAUTION: DO NOT short pin 2 to ground asthis can damage the internal 8 V regulator. DCvoltage is applied to pin 1 or microphone opera-

tion. Use caution when using a non-Icom micro-phone.

HM-36 SCHEMATIC DIAGRAM

+

q

w

ert

y

u

i

4700pF

0.33F

MICROPHONE

MIC

ELEMENT

2k

470

DOWN UP

PTT RECEIVE

TRANSMIT

MICROPHONE CABLE MICROPHONE PLUG

1k+

10F

q UP/DOWN SWITCHES [UP]/[DN]Change the selected readout requency or memory

channel. Pushing the switch continuously changes the requency

or memory channel number continuously.

The [UP]/[DN] switch can simulate a key paddle. Select

in set mode (U/D KEY; Mic Up/Down Keyer). (p. 80)

While pushing and holding RIT *, push the [UP]/[DN]

switch to control the transmit readout requency while

in spilt requency operation.

* Available only when the XFC (transmit requency

check) unction is turned ON. (p. 76)

w PTT SWITCHPush and hold to transmit; release to receive.

e PTT LOCK SWITCH (SM-20 only)Push to lock the PTT switch to the transmissioncodition.

q

w

q

we

Microphones

D HM-36

D SM-20(Option)

1 PANEL DESCRIPTION

8/7/2019 IC-7200 Manual

17/104

8/7/2019 IC-7200 Manual

18/104

8/7/2019 IC-7200 Manual

19/104

8/7/2019 IC-7200 Manual

20/104

8/7/2019 IC-7200 Manual

21/104

16

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

External antenna tuners

CONNECTING THE AH-4

GroundGround

Long wire or optional AH-2b

AH-4[ANT]

IC-7200

Coaxial cable(from the AH-4)

[TUNER]

CONNECTING THE AT-180

IC-7200

Ground

AT-180

HF

to 6 m

antenna

[TRANSCEIVER]

[ANT][ANT][ACC] [ACC]

ACC cable supplied with the AT-180

Coaxial cable suppliedwith the AT-180

Either of the twoexternal connectors

Ground

Turn the IC-7200s power OFF when connectingthe AT-180, otherwise, the CPU may malunctionand the AT-180 may not unction properly.

2INSTALLATION AND CONNECTIONS

8/7/2019 IC-7200 Manual

22/104

8/7/2019 IC-7200 Manual

23/104

8/7/2019 IC-7200 Manual

24/104

8/7/2019 IC-7200 Manual

25/104

8/7/2019 IC-7200 Manual

26/104

8/7/2019 IC-7200 Manual

27/104

8/7/2019 IC-7200 Manual

28/104

8/7/2019 IC-7200 Manual

29/104

8/7/2019 IC-7200 Manual

30/104

8/7/2019 IC-7200 Manual

31/104

26

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D Programmable tuning steps

D Selecting the programmable tuning step

Programmable tuning steps are available to suit youroperating requirements.These tuning steps are: Selectable rom 0.1, 1, 5, 9 and 10 kHz

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL]

q Push TS to turn the programmable tuning unc-tion ON. Z appears.

Programmable tuning step indicator

w Push and hold TS or 1 sec. to enter the tuningstep set mode.

e Rotate [DIAL] to select the desired tuning step

rom 0.1, 1, 5, 9 or 10 kHz.r Push TS to exit the tuning step set mode.t Rotate [DIAL] to change the requency according

to the set tuning step.

y Push TS to turn the programmable tuning unc-tion OFF. Z disappears.

The operating requency can be changed in steps o(0.1, 1, 5, 9 or 10 kHz selectable) or quick tuning.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL]

q Push TS to turn the programmable tuning unc-tion ON. Z appears.

Programmable tuning step indicator

w Rotate [DIAL] to change the requency in pro-grammed kHz steps.

e Push TS again to turn the programmable tuning

unction OFF. Z disappears.

r Rotate [DIAL] or normal tuning, i desired.

3BASIC OPERATION

8/7/2019 IC-7200 Manual

32/104

8/7/2019 IC-7200 Manual

33/104

8/7/2019 IC-7200 Manual

34/104

8/7/2019 IC-7200 Manual

35/104

30

3BASIC OPERATION

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

RF gain and Squelch

Meter unction

The [RF/SQL] control adjusts the RF gain andsquelch threshold level. The squelch stops noise out-

put rom the speaker (closed position) when no sig-nal is received. The 12 oclock position is recommended or any setting

o the [RF/SQL] control.

The [RF/SQL] control can be set as the RF gain control

only (squelch is xed open) or squelch control (RF gain is

xed at maximum) in the set mode (p. 75). See the table

as below.

MODESET MODE SETTING

AUTO SQL RF + SQL

SSB, CW

RTTYRF GAIN SQL RF GAIN + SQL

AM SQL SQL RF GAIN + SQL

Adjusting RF gain (Receive sensitivity)Normally, the [RF/SQL] control is set to the 12 oclockposition.Rotate the [RF/SQL] control to the 11 oclock posi-tion or maximum sensitivity. Rotate the [RF/SQL] control clockwise to increase, coun-

terclockwise to decrease the receiver sensitivity.

The S-meter indicates receive sensitivity.

Adjusting squelch (Removing non-signal noise)

Rotate the [RF/SQL] control to the 1 oclock posi-tion to invoke the S-meter squelch this allows youto set the minimum signal level needed to open thesquelch. A segment appears in the S-meter to indicate the S-me-

ter squelch level.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[RF/SQL]

Minimum RF gain

Adjustable range

RF gain adjustablerange

Maximum RF gain

Maximum RF gain

Squelch is open. S-meter squelch

S-meter squelch

threshold

Squelch is open.

S-meter squelch

S-meter squelch

threshold

When functioning as RF GAIN/SQL control

When functioning as RF GAIN control

When functioning as SQL control

Lowest Threshold Highest Threshold

The transceiver has 3 transmit meter unctions oryour convenience. Select the desired meter rom RFpower (Po), ALC and SWR.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

Push and holdANF

METER or 1 sec. to toggle betweenRF power (Po), SWR and ALC. The display indication changes as the ollowing table.

DISPLAY

INDICATIONMEASUREMENT

Po Indicates the relative RF output power.

SWR Indicates the SWR on the transmission line.

ALC

Indicates the ALC level. When the meter

movement shows the input signal level

exceeds the allowable level, the ALC lim-its the RF power. In such cases, reduce

the MIC gain setting (see p. 31) in the

quick set mode.

8/7/2019 IC-7200 Manual

36/104

8/7/2019 IC-7200 Manual

37/104

8/7/2019 IC-7200 Manual

38/104

8/7/2019 IC-7200 Manual

39/104

34

4RECEIVE AND TRANSMIT

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D Convenient unctions or transmit

VOX (voice operated transmit) (p. 53) Push VOX to turn the VOX unction ON or OFF.

appears when the VOX unction is ON.

Push and hold VOX or 1 sec. to enter the VOXset mode, then rotate [DIAL] to adjust the VOXgain, anti VOX gain or VOX delay. Rotate [M-CH] to select an item.

Speech compressor (p. 57) Push COMP to turn the speech compressor ON

or OFF. appears when the speech compressor is ON.

Push and hold COMP or 1 sec. to enter the com-pression level set mode, then rotate [DIAL] to ad-just the compression level.

D About 5 MHz band operation (USA version only)

Operation on the 5 MHz band is allowed on 5 dis-crete requencies and must adhere to the ollowing:

USB mode Maximum o 50 watts ERP (Eective Radiated Power)

2.8 kHz bandwidth

It is the operators responsibility to set all controls sothat the transmission in this band meets the stringentconditions under which we may use these requen-cies.

NOTE: We recommend that you store these re-quencies, mode and ilter settings into the mem-ory channel or easy recall.

IC-7200

Display Frequency*

FCC Channel

Center Frequency*

5.33050 MHz 5.33200 MHz

5.34650 MHz 5.34800 MHz

5.36650 MHz 5.36800 MHz

5.37150 MHz 5.37300 MHz

5.40350 MHz 5.40500 MHz

*The channel center requencies that are speciiedby the FCC, show the center requency o theirpassband. However, the IC-7200 displays carrierpoint requency, so set 1.5 kHz below rom FCCchannel center requency.

To assist you in operating the 5 MHz band cor-rectly within the rules speciied by the FCC,transmission is impossible on any 5 MHz bandrequency other than the 5 requencies indicated inthe table above.

8/7/2019 IC-7200 Manual

40/104

35

Operating CW

q Connect a paddle, straight key or external elec-tronic keyer as on page 18.

w Push and hold F-INP ENTBAND or 1 sec., then push aband key to select the desired band.

e Push MODE to select CW mode.

Ater CW mode is selected, push and hold MODE or

1 sec. to toggle between CW and CW-R modes.

r Rotate [DIAL] to tune in a desired signal with thedesired tone requency. The S-meter indicates received signal strength when

signal is received.

t Rotate the [AF] control to set audio to a comort-able listening level.

y Set CW break-in operation and the CW delay time

in the set mode. (p. 79)q Push and hold

M-CH/RITSET or 1 sec. twice to enter

the set mode.

w Rotate [M-CH] to select BK-IN to set the CWbreak-in operation.

e Rotate [DIAL] to select the CW break-in opera-tion rom ull break-in, semi break-in or OFF. FL : ull break-in

SE : semi break-in

OF : break-in OFF

r Rotate [M-CH] to select BK-DELAY to selectthe CW delay time when semi break-in operation

is selected in stepe

.t Rotate [DIAL] to set the desired delay time.

y Continue to set the keyer settings in the setmode, i necessary. (p. 80)

u Push M-CH/RITSET to exit the set mode and return tonormal operation.

u Keying to transmit, use the paddle, straight key orexternal electronic keyer to send your CW signals. appears.

The Po meter indicates the transmit power strength.

i Stop keying to return to receive.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

Band keys

[DIAL][AF]

CW or CW-R appears.

Appears while transmitting.

[M-CH]

Appears when semi break-in is selected.

4 RECEIVE AND TRANSMIT

8/7/2019 IC-7200 Manual

41/104

8/7/2019 IC-7200 Manual

42/104

8/7/2019 IC-7200 Manual

43/104

8/7/2019 IC-7200 Manual

44/104

8/7/2019 IC-7200 Manual

45/104

40


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D RTTY reverse mode

Received characters are occasionally garbled whenthe receive signal is reversed between MARK andSPACE. This reversal can be caused by incorrectTNC connections, settings, commands, etc.

To receive a reversed RTTY signal correctly, selectRTTY-R (RTTY reverse) mode.

qPush MODE to select RTTY mode.

wAter RTTY mode is selected, push and holdMODE or 1 sec. to toggle between RTTY and

RTTY-R modes.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

ReverseNormal

BFO

170

Hz

2125

Hz

170

Hz

2125

Hz

BFO

MarkSpace

Displayed freq.Displayed freq.

MarkSpace

DTwin peak lter

The twin peak ilter changes the receive requencyresponse by boosting two particular requencies

(2125 and 2295 Hz) or better copying o desired RTTY

signals.

qPush MODE to select RTTY mode. Ater RTTY mode is selected, push and hold MODE

or 1 sec. to toggle between RTTY and RTTY-R modes.

w Push and hold M-CH/RITSET or 1 sec. to enter thequick set mode.

e Rotate [M-CH] to select TPF, then rotate [DIAL]to select the twin peak lter unction ON or OFF. The received audio volume may become greater when

the twin peak lter is turned ON.

r PushM-CH/RIT

SET to exit the quick set mode and re-

turn to normal operation.

OFF (default)

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

8/7/2019 IC-7200 Manual

46/104

41

4 RECEIVE AND TRANSMIT

D RTTY decode set mode

Set the RTTY key polarity, shit width and mark tone.

qWhen RTTY (RTTY-R) mode is selected, push andhold M-CH/RITSET or 1 sec. to enter the quick set mode.

w Rotate [M-CH] to select the desired set item.

e Rotate [DIAL] to adjust the desired value or con-dition. Push and hold M-CL or 1 sec. to return to the deault

value.

r PushM-CH/RIT

SET to exit the quick set mode and re-turn to normal operation.

[DIAL]

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[M-CH]

RTTY mark tone (RTTY mode)

This item selects the RTTY mark requency. RTTY markrequency is switched between 1275, 1615 and 2125 Hz.

2125 Hz (default)

RTTY shit width (RTTY mode)

This item adjusts the RTTY shit width. There are 4selectable values: 170, 200, 425 and 850 Hz.

170 Hz (default)

RTTY key polarity (RTTY mode)

This item selects the RTTY keying polarity. Normal orreverse keying polarity can be selected.When reverse polarity is selected, Mark and Space arereversed.n (normal) : Key open/close = Mark/Space

r (reverse) : Key open/close = Space/Mark

NORMAL (default)

8/7/2019 IC-7200 Manual

47/104

42


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

Operating AM

q Push and holdF-INP ENT

BAND or 1 sec., then push aband key to select the desired band.

w Push MODE to select AM mode.e Rotate [DIAL] to tune in a desired signal.

The S-meter indicates received signal strength when a

signal is received.

The deault tuning step or AM mode is 1 kHz; this

can be changed using the tuning step program mode.

(p. 26)

r Rotate the [AF] control to set audio to a comort-able listening level.

t Push [PTT] (microphone) to transmit. appears.

y Speak into the microphone at your normal voicelevel.

Adjust MIC Gain at this step, i necessary. (p. 71)u Release [PTT] (microphone) to return to receive.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL][AF]

Appears while transmitting.

F-INPENT

BAND

Band keys

AM appears.

D Convenient unctions or receive

Preamp and attenuator (p. 45)

PushP.AMP

ATT to turn the preamp ON or OFF.

appears when the preamp is set to ON.

Push and hold P.AMPATT or 1 sec. to turn the attenu-ator ON.

PushP.AMP

ATT to turn the attenuator OFF.

appears when the attenuator is set to ON.

AGC (auto gain control) (p. 45)

Push AGC once or twice to select the time con-stant or the AGC circuit ast and slow. F.AGC appears when the ast time constant is se-

lected, and no indicator appears when the slow time

constant is selected, respectively.

Push and hold AGC or 1 sec. to turn the AGCunction OFF. AGC-OFF appears on the display.

Noise blanker (p. 49)

Push NB to turn the noise blanker ON or OFF. appears when the noise blanker is set to ON.

Push and hold NB or 1 sec. to enter the noiseblanker set mode, then rotate [DIAL] to adjust thethreshold level, or the blank time. Rotate [M-CH] to select an item.

Twin PBT (passband tuning) (p. 46)

Rotate [TWIN PBT] (controlsinner/outer).

Noise reduction (p. 50)

Push NR to turn the noise reduction ON or OFF. appears when the noise reduction is ON.

Push and hold NR or 1 sec. to enter the noise

reduction level set mode, then rotate [DIAL] toadjust the noise reduction level.

Manual notch lter (pgs. 51, 52)

Push MNF to turn the manual notch lter ON orOFF. appears when the manual notch ilter is set to

ON.

Push and hold MNF or 1 sec. to enter the man-ual notch lter set mode, then rotate [DIAL] to se-lect the lter width rom narrow, middle and wide.

Auto notch lter (p. 51) Push

ANFMETER to turn the auto notch ilter ON or

OFF. appears when the auto notch ilter is set to

ON.

D Convenient unctions or transmit

VOX (voice operated transmit) (p. 53)

Push VOX to turn the VOX unction ON or OFF. appears when the VOX unction is ON.

Push and hold VOX or 1 sec. to enter the VOXset mode, then rotate [DIAL] to adjust the VOX

gain, anti VOX gain or VOX delay. Rotate [M-CH] to select an item.

8/7/2019 IC-7200 Manual

48/104

8/7/2019 IC-7200 Manual

49/104

8/7/2019 IC-7200 Manual

50/104

8/7/2019 IC-7200 Manual

51/104

8/7/2019 IC-7200 Manual

52/104

47

5 FUNCTIONS FOR RECEIVE

IF lter selection

The transceiver has 3 passband IF ilter widths oreach mode.

For SSB and CW modes, the passband width can beset rom 50 to 3600 Hz in 50 or 100 Hz steps.A total o 41 passband widths are available.

For RTTY mode, the passband width can be set rom50 to 2700 Hz in 50 or 100 Hz steps.A total o 32 passband widths are available.

For AM mode, the passband width can be set rom200 to 8000 Hz in 200 Hz steps.

A total o 40 passband widths are available.

The ilter selection is automatically memorized ineach mode.

D IF lter selection

q Push MODE several times to select the desired

mode.w Push FILTER several times to select the IF ilter

rom Wide, Middle or Narrow. The selected IF ilter indicator ( , or )

appears in the LCD.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

Selected IF filter indicator

8/7/2019 IC-7200 Manual

53/104

48

5FUNCTIONS FOR RECEIVE

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D FIlter passband width setting

q Push MODE several times to select the desiredmode.

w Push and hold FILTER or 1 sec. to enter lter setmode.

e Rotate [M-CH] to select FIL.

r Push FILTER several times to select the desiredIF lter.

t Rotate [DIAL] to set the desired passband width. The passband width can be set within the range as

shown in the table at right below.

Push and hold M-CL or 1 sec. to return to the deault

value.

y Repeat stepsr andt i desired.

u Push and hold FILTER or 1 sec. to exit the ilterset mode.

When the IF passband width is set to minimum bythe [TWIN PBT] controls (when one control ismax. counterclockwise, and the other one is max.clockwise; p. 46), a sound may not come rom thespeaker depending on the IF lter passband widthsetting. This is not a transceivers malunction.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

Mode Filter Deault Range (Steps)

SSB

Wide 3000 Hz50500 Hz (50 Hz)/

6003600 Hz (100 Hz)Middle 2400 Hz

Narrow 1800 Hz

SSB Data/

CW

Wide 1200 Hz50500 Hz (50 Hz)/

6003600 Hz (100 Hz)Middle 500 Hz

Narrow 250 Hz

RTTY

Wide 2400 Hz50500 Hz (50 Hz)/

6002700 Hz (100 Hz)Middle 500 Hz

Narrow 250 Hz

AM/

AM Data

Wide 8000 Hz

2008000 Hz (200 Hz)Middle 6000 Hz

Narrow 3000 Hz

D IF Ilter shape (SSB/CW only)

The type o DSP lter shape or SSB and CW can beselected independently rom sot and sharp.

q Push MODE several times to select SSB or CW

mode.w Push and hold FILTER or 1 sec. to enter lter set

mode.e Rotate [M-CH] to select SHAPE.

r Push FILTER several times to select the desiredIF lter rom Wide, Middle or Narrow.

t Rotate [DIAL] to select the desired ilter shape,either sot or sharp


value.

y Push and hold FILTER or 1 sec. to exit the ilterset mode.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATT

P.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

Sharp

Soft

8/7/2019 IC-7200 Manual

54/104

49


Noise blanker

The noise blanker eliminates pulse-type noise suchas rom car ignition systems.

Push NB to turn the noise blanker ON or OFF.

appears when the NB unction is ON.

When using the noise blanker, received signalsmay be distorted i they are excessively strong orthe noise type is other than impulse. Nearbystrong signals can also cause the noise blanker tocreate distortion. Turn the noise blanker unctionOFF, or adjust the noise blanker level to a shal-lower setting (see below) in this case.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

Appears

D Noise blanker settings

q Push and hold NB or 1 sec. to enter the noiseblanker set mode.

The noise blanker is turned ON and appears.

w Rotate [M-CH] to select the desired set item.

e Rotate [DIAL] to adjust the desired condition.

Push and hold M-CL or 1 sec. to return to the deaultvalue.

r Push NB to exit the noise blanker set mode.

t Push NB to turn the noise blanker OFF i neces-sary.

disappears.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

Appears

NB LEVEL

This item adjusts the noise blanker level. The noiseblanker attenuation level can be adjusted rom 0% to

100%.

50% (default)

NB WIDTH

This item allows adjustment o the blank time or noiseblanker to match the pulse width. The noise blanker widthcan be adjusted rom 1% to 100%.

50% (default)

8/7/2019 IC-7200 Manual

55/104

50


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

Noise reduction

The noise reduction enhances desired signals inthe presence o noise by using the DSP circuit to re-move random noise. The amount o enhancement isadjustable.

Push NR to turn the noise reduction ON or OFF.

appears when the NR unction is ON.

The noise reduction level can result in audio sig-nal masking. Set the noise reduction level ormaximum readability as described below.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

Appears

Noise reduction OFF

NR Level 0

Noise reduction is activated

NR Level 4 (default)

Desired

signal (CW)

Noise components

D Noise reduction level setting

q Push and hold NR or 1 sec. to enter the noisereduction level set mode. The noise reduction is turned ON and appears.

w Rotate [DIAL] to adjust the noise reduction level. The noise reduction level can be adjusted rom 0 to

15.


value.

e Push NR to exit the noise reduction set mode.r Push NR to turn the noise reduction OFF i nec-

essary.

disappears.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL]

4 (default)

Appears

8/7/2019 IC-7200 Manual

56/104

51


Notch unction

This transceiver has auto and manual notch unc-

tions.The auto notch unction automatically attenuatesbeat tones, tuning signals, changing requency, etc.,even i they are moving.The manual notch can be set to attenuate a re-quency via the [MNF] control.

PushANF

METER to turn the auto notch unction ON or

OFF. appears when the auto notch unction is ON. The auto notch unction is available while in SSB or

AM mode.

Push MNF to turn the manual notch unction ONor OFF. appears when the manual notch unction is

ON.

While in SSB or AM mode, either the auto or manual

notch unction can be turned ON. These unctions are

selected by pushing ANFMETER or MNF .

Manual notch ilter setting is described on the next

page.

D Auto notch unction

The auto notch can be used in SSB and AM modes.

PushANF

METER to turn the automatic notch unctionON or OFF. appears when the auto notch unction is ON.

Unwanted interference

Desiredsignal (AF)

Desiredsignal (AF)

Interference frequency

is attenuated

Auto notch OFF Auto notch ON

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

Appears

D Manual notch unction

Push MNF to turn the manual notch unction ON

or OFF. appears when the manual notch unction is

ON.

Set to attenuate a requency or manual notch via the

[MNF] control.

Set the requency or manual notch iltering via the

manual notch ilter set mode. (described on the next

page)

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

Appears

[MNF]

8/7/2019 IC-7200 Manual

57/104

52


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D Manual notch lter setting

q Push and hold MNF or 1 sec. to enter the man-ual notch lter set mode. The manual notch unction is turned ON and

appears.

w Rotate [DIAL] to select the ilter width rom nar-row, middle and wide.


value.

e Push MNF to exit the manual notch ilter setmode.

r Push MNF to turn the manual notch unctionOFF i necessary.

disappears.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL]

Middle (default)

While adjusting the manual notch lter, noise maybe heard. This comes rom the DSP unit and doesnot indicate an equipment malunction.

8/7/2019 IC-7200 Manual

58/104

6

53

FUNCTIONS FOR TRANSMIT

VOX unction

The VOX (Voice-Operated Transmission) unctionuses your voice to switch between transmit andreceive. This unction provides an opportunity orhands-ree operation or to input log entries into yourcomputer, etc., while operating.

q Push MODE to select a phone mode (SSB orAM). When SSB mode is selected, push and hold MODE

or 1 sec. to toggle between USB and LSB modes.

w Push VOX to toggle the VOX unction ON andOFF. appears when the VOX unction is ON.

The VOX gain, ANTI-VOX and VOX delay can be setin VOX set mode. (See below.)

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH] VOX289

Appears

D Adjusting the VOX unction

q Push MODE to select a phone mode (SSB orAM). When SSB mode is selected, push and hold MODE


w Push VOX to toggle the VOX unction ON andOFF. appears when the VOX unction is ON.

eAdjust the VOX unctions in the VOX set mode.

q Push and hold VOX or 1 sec. to enter the VOXset mode.

w Rotate [M-CH] to select VoX GAIN.

eWhile speaking into the microphone with yournormal voice level, rotate [DIAL] to the pointwhere the transceiver is continuously transmit-ting.

r Rotate [M-CH] to select ANTI-Vox.t During receive, rotate [DIAL] to adjust the anti-

VOX gain to the point where the transceiver

does not switch to transmit due to receivedaudio rom the speaker.

y Rotate [M-CH] to select VoX DELY.

u Rotate [DIAL] to adjust the VOX delay or aconvenient interval beore returning to receive.

i Push VOX to exit the VOX set mode. and returnto normal operation.

VOX Gain

50% (default)

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH] VOX 289

8/7/2019 IC-7200 Manual

59/104

54

6FUNCTIONS FOR TRANSMIT

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D VOX set mode

VOX GAINThis item adjusts the VOX gain or the VOX (Voice-Oper-ated Transmission) unction. Higher values make the VOXunction more sensitive to your voice.This setting can be adjusted rom 0% to 100% in 1%steps.

Push and hold M-CL or 1 sec. to return to the deault value.50% (default)

ANTI-VOX

This item adjusts the ANTI-VOX gain or the VOX (Voice-Operated Transmission) unction. Higher values make theVOX unction less sensitive to receiver output audio roma speaker or headphones.This setting can be adjusted rom 0% to 100% in 1%steps.

Push and hold M-CL or 1 sec. to return to the deault value.

50% (default)

VOX DELAY

This item adjusts the VOX (Voice-Operated Transmission)delay time. VOX Delay is the amount o time the transmit-ter stays on ater you stop speaking.The delay time can be adjusted rom 0 to 2.0 sec. in 0.1sec. steps.

Push and hold M-CL or 1 sec. to return to the deault value.

0.2 sec. (default)

8/7/2019 IC-7200 Manual

60/104

55

6 FUNCTIONS FOR TRANSMIT

Break-in unction

The break-in unction is used in CW mode to auto-matically switch the transceiver between transmit and

receive when keying. The IC-7200 is capable o ullbreak-in or semi break-in. Break-in operation is alsoreerred to as QSK.

D Semi break-in operation

During semi break-in operation, the transceiver im-mediately transmits when keying, then automati-cally returns to receive ater a pre-set delay time haspassed rom when you stop keying. This is similiar toVOX operation or voice.

q Push MODE to select CW or CW-R mode. When CW mode is selected, push and hold MODE

or 1 sec. to toggle between CW and CW-R modes.

wSet the semi break-in unction ON in the set mode.

q Push and hold M-CH/RITSET or 1 sec. twice to enterthe set mode.

w Rotate [M-CH] to select BK-IN to set the CWbreak-in operation.

e Rotate [DIAL] to select SE. FL : Full break-in

SE : Semi break-in

OF : Break-in OFF

r Rotate [M-CH] to select BK-DELAY to selectthe CW delay time when semi break-in opera-tion is selected in stepe.

t Rotate [DIAL] to set the desired delay time. The delay time is selectable rom 0.2 to 13.0 (dots)

in 0.1 (dots) steps.

y Push M-CH/RITSET to exit the set mode and return tonormal operation.

e BK appears on the LCD.

When using a paddle, set KEY SPD in the quick

set mode to adjust the keying speed. (p. 72)

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

Appears

7.5 dots

Semi break-in operation

8/7/2019 IC-7200 Manual

61/104

56


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

D Full break-in operation

During ull break-in operation, the transceiver auto-matically switches to receive between keying dotsand dashes so that the operator can hear activity onthe channel when transmitting.

q Push MODE to select CW or CW-R mode. When CW mode is selected, push and hold MODE

or 1 sec. to toggle between CW and CW-R modes.

wSet the ull break-in unction ON in the set mode.


w Rotate [M-CH] to select BK-IN to set the CW

break-in operation.e Rotate [DIAL] to select FL.

FL : ull break-in

SE : semi break-in

OF : break-in OFF

r PushM-CH/RIT

SET to exit the set mode and return tonormal operation.

e F-BK appears on the LCD.

When using a paddle, set KEY SPD in the quickset mode to adjust the keying speed. (p. 72)

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

Appears

Full break-in operation

8/7/2019 IC-7200 Manual

62/104

57


Speech compressor

The IC-7200 has a built-in, low distortion speech com-pressor circuit. This circuit increases your average talk

power in SSB mode and is especially useul or DX-ing or noisy conditions when the receiving station ishaving diculty copying your signal.

q Push MODE to select an SSB mode.

When SSB mode is selected, push and hold MODE


w Push COMP to turn the speech compressor unc-tion ON and OFF. appears when the speech compressor unc-

tion is ON.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL]

Appears

COMP 721

D Compression level setting

Microphone gain setting

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

q Push MODE to select an SSB mode.

When SSB mode is selected, push and hold MODE


w Push COMP to turn the speech compressor unc-tion OFF, i its ON. disappears.

e Push and holdANF

METER or 1 sec. several times toselect ALC meter. ALC appears.

r Adjust the MIC gain in the quick set mode.

q Push and hold M-CH/RITSET or 1 sec. to enter thequick set mode.

w Rotate [M-CH] to select MIC GAIN to set themicrophone gain.

eWhile transmitting, speak at a normal voice leveland rotate [DIAL] to adjust the microphone gainso that the ALC meter reads within the ALCzone, whether you speak sotly or loudly. Push and hold M-CL or 1 sec. to return to the de-

ault value.

r Push M-CH/RITSET to exit the quick set mode andreturn to normal operation.

Compression level setting

q Push and hold ANFMETER or 1 sec. several times toselect ALC meter. ALC appears.

w Push and hold COMP or 1 sec. to enter thespeech compression level set mode. The speech compressor unction is turned ON and

appears.

You can enter the speech compression level setmode beore selecting ALC meter in step q.

eWhile transmitting, speak at a normal voice leveland rotate [DIAL] to adjust the speech compres-sion level so that the ALC meter reads within theALC zone, whether you speak sotly or loudly. The speech compression level can be adjusted rom 0

to 10.


value.

Level 5 (default)

ALC zone

rPush COMP to exit the speech compression levelset mode and return to normal operation.

t Push COMP to turn the speech compressor unc-tion OFF i necessary.

disappears.

NOTE: When the ALC meter peaks above the ALCzone, your transmitted voice may be distorted.

8/7/2019 IC-7200 Manual

63/104

58


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

Split requency operation

Split requency operation allows you to transmit andreceive in the same mode on two dierent requen-

cies. The split requency operation is perormed using2 requencies in VFO A and VFO B.

The transmit and receive requencies must be inthe same band

The ollowing is an example o setting 7.0620 MHz orreceiving and 7.0750 MHz or transmitting.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANF

METERNRNB

[DIAL] [M-CH]

F-INPENT

BAND

A/B 2=

3.5SPLIT 3

7Keypad

q Push A/B= to select VFO A.

w Set the requency to 7.0620 MHz and mode toLSB. (pgs. 25, 29)

e Push SPLIT to turn the split unction ON. appears on the LCD.

Appears

r Push and holdA/B= or 1 sec. to equalize the un-

displayed VFO B requency and operating modewith the displayed VFO A.

t Push A/B= to select the VFO B.

y Set the requency to 7.0750 MHz (LSB). (p. 25)

u Push A/B= to return to the VFO A.

i Now you can receive on 7.0620 MHz and transmiton 7.0750 MHz.

To swap the transmit and receive requencies,push A/B= to exchange the VFO A and VFO B.

CONVENIENT!

QUICK SPLIT FUNCTION (p. 59)

When you push and hold SPLIT or 1 sec., the splitunction is activated, and the undisplayed VFO is setthe same as the displayed VFO. (This operation issame as the stepse andr as at let.)

This shortens the time needed to start split re-quency operation.

Quick split unction is turned ON by deault but canbe turned OFF in the set mode (p. 76).

XFC FUNCTION (p. 76)When the XFC (transmit requency check) unction

is ON, the transmit requency can be changed (thisoperation is same as the stepst andy as at let.)

NOTE: When the XFC unction is ON, the RIT cal-culation unction (p. 44) is not available.

q Set the XFC (transmit requency check) unctionON in the set mode.


w Rotate [M-CH] to select XFC.e Rotate [DIAL] to select ON.

r Push M-CH/RITSET to exit the set mode and return tonormal operation.

wWhile pushing and holding RIT , the transmit re-quency is indicated. And rotate [DIAL] to set thetransmit requency.

8/7/2019 IC-7200 Manual

64/104

59


D Quick split unction

When you nd a DX station, an important considera-tion is how to set the split requency.

When you push and hold SPLIT or 1 sec., the splitunction is activated, and the undisplayed VFO is setthe same as the displayed VFO.This shortens the time needed to start split re-quency operation.

Quick split operation is turned ON by deault but canbe turned OFF in the set mode (p. 76).

The ollowing is an example o setting 7.0620 MHzor receiving and 7.0750 MHz or transmitting.

q Select VFO A. Pushing A/B= toggles VFO A and VFO B.

w Set the requency to 7.0620 MHz and mode toLSB. (pgs. 25, 29)

e Push and hold SPLIT or 1 sec. to turn the splitunction ON and equalize the undisplayed VFO Brequency and operating mode with the displayedVFO A.

appears on the LCD.

r Set the XFC (transmit requency check) unctionON in the set mode. (pgs. 58, 76)

The deault setting is OFF.

tWhile pushing and holding RIT , rotate [DIAL] toset the transmit requency to 7.0750 MHz.

y Now you can receive on 7.0620 MHz and transmiton 7.0750 MHz.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[DIAL] [M-CH]

A/B 2=

3.5SPLIT 3

7

Appears

D Split lock unction

Accidentally releasing RIT while rotating [DIAL]changes the receive requency. To prevent this, useboth the split lock and dial lock unctions to changethe transmit requency only. The split lock unc-

tion cancels the dial lock unction while pushing andholding RIT during split requency operation.

The dial locks eectiveness during split requencyoperation can be selected in the set mode or bothreceive and transmit requencies; or only the receiverequency. (p. 76)

When the split lock unction is ON, the transmit re-quency cannot be adjusted by rotating [DIAL] whiletransmitting even i the lock unction is not activated.

q Set the split lock unction ON in the set mode.


w Rotate [M-CH] to select SPLIT LK.

e Rotate [DIAL] to select ON.r Push M-CH/RITSET to exit the set mode and return to

normal operation.

w During split operation, push and hold SPCH or1 sec. to turn the dial lock unction ON.

appears on the LCD.

eWhile pushing and holding RIT *, the transmitrequency and mode are indicated. And Rotate[DIAL] to set the transmit requency.

*XFC unction is should be turned ON in advance. (p. 76)

8/7/2019 IC-7200 Manual

65/104

60


1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

Measuring SWR

The IC-7200 has a built-in circuit or measuring an-tenna SWRno external equipment is necessary.

q Push MODE to select CW or RTTY mode.

w Conrm that the output power is over 30 W.

e Push and hold ANFMETER or 1 sec. several times toselect the SWR meter.

r Push [PTT] to transmit; then read the actual SWRrom the meter. 1.5 well-matched antenna

> 1.5 may indicate an antenna out o its well-matched

requency range. I much larger than 2.0, check an-

tenna and cable connections, etc.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETER

NRNB

Appears The best match is in this range.

8/7/2019 IC-7200 Manual

66/104

7

61

MEMORY OPERATION

Memory channels

The transceiver has 201 memory channels including2 scan edge channels.

Memory mode is very useul or quickly changing tooten-used requencies.

All 201 memory channels are tuneable which meansthe programmed requency can be tuned temporarily

with [DIAL], etc., in memory mode.

MEMORY

CHANNEL

MEMORY

CHANNEL

NUMBER

CAPABILITYCOPY

TO VFO

OVER-

WRITINGCLEAR

Regular memory

channels1199

Independent transmit and receive requencies

and mode in each memory channel.Yes Yes Yes

Scan edge

memory channelsP1, P2

One requency and one mode in each memory

channel as scan edges or programmed scan.Yes Yes No

Memory channel selection

q Push V/M to select memory mode.

appears.

w Rotate [M-CH] to select the desired memorychannel. I the RIT control indicator lights orange, push

M-CH/RITSET to set the [M-CH] control to memory chan-

nel control. (See below or details)

All memory channels including blank channels can be

selected.

[UP]/[DN] on the microphone also selects the mem-ory channels. (The only programmed memory chan-

nels are selectable.)

Channel decreases

Channel increases

RIT control indicatorgoes out

About the [M-CH] control:When the RIT control indicator lights orange, the

memory channels cannot be selected with rotat-ing the [M-CH] control because the [M-CH] con-trol acts as the RIT control. So, push M-CH/RITSET toset the [M-CH] control to memory channel control(RIT control indicator goes out).

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[M-CH]

RIT control

indicator

[EXAMPLE]: Selecting memory channel 17.

Push

Appears

Rotate [M-CH]

VFO mode

Memory mode

Channel 17 is selected.

8/7/2019 IC-7200 Manual

67/104

8/7/2019 IC-7200 Manual

68/104

63

Frequency copying

The requency and operating mode in a memorychannel can be copied to the VFO.

D Copying in memory mode

This is useul or copying a memory channels con-tents (requency and operating mode) to a VFO whileoperating in memory mode.This is useul when searching or signals around amemory channel requency.

NOTE: While operating in VFO mode, pushing andholding V/M or 1 sec. also copy the selectedmemory channels contents (requency and oper-

ating mode) to a VFO.

When you have changed the requency or operat-ing mode in the selected memory channel: Displayed requency and mode are copied. Programmed requency and mode in the mem-

ory channel are not copied, and they remain inthe memory channel.

q Push V/M to select memory mode.w Rotate [M-CH] to select the desired memory

channel to be copied. I the RIT control indicator lights orange, push

M-CH/RITSET . (p. 61)

Set the requency or operating mode i required. appears i the selected memory channel is a

blank channel (and does not have contents). In this

case copying is not possible.

Channel decreases

Channel increases

RIT control indicator

goes out

e Push and hold V/M

or 1 sec. to copy the re-quency and operating mode. 3 beeps are emitted when the copying is successul.

Displayed requency and operating mode are copied.

r To return to VFO mode, push V/M . Copied requency and operating mode appear in the

display.

You can return to VFO mode beore copyingthe requency and operating mode in step e.

[EXAMPLE]: Copying contents of memory 16.Operating frequency

Contents of memory 16

: 14.020 MHz/CW

: 14.018 MHz/CW

V/M 11.8Push and hold for 1 sec.,

then push .V/M 11.8

Rotate [M-CH]

7 MEMORY OPERATION

8/7/2019 IC-7200 Manual

69/104

8/7/2019 IC-7200 Manual

70/104

8

65

SCAN OPERATION

ChannelsFor programmed scan:Program scan edge requencies into scan edge mem-ory channels P1 and P2. (p. 66)

For memory scan:Program two or more memory channels except scanedge memory channels.

Scan resume ON/OFF

You can select the scan to resume or cancel whendetecting a signal in the set mode.Scan resume ON/OFF must be set beore operating ascan. See p. 78 or ON/OFF setting and scan resumecondition details.

Scan speedScan speed can be selected rom 2 levels, high orlow, in the set mode. See p. 78 or details.

Squelch condition

Scan starts with squelch openFor programmed scan:

When tuning step is 1 kHz or less:The scan continues until it is stopped manually withpushing SCAN , and does not pause* even i signalsare detected.* The scan is paused when the squelch is closed and

then opened (scan resumes ater 10 sec. has passed

when the scan resume is ON; scan is cancelled when

OFF).

When tuning step is more than 5 kHz:The scan pauses on each step when the scanresume is ON; not applicable when OFF.

For memory scan:Scan pauses on each channel when the scan resumeis ON; not applicable when OFF.

Scan starts with squelch closedScan stops when a signal is detected.I you set scan resume ON in the set mode, the scan

pauses or 10 sec. when detecting a signal, thenresumes. When a signal disappears while scan ispaused, scan resumes 2 sec. later.

NOTE: I the [RF/SQL] control unction is set asAUTO, the squelch is always open in SSB, CWand RTTY modes. (pgs. 4, 30, 75)

Scan types

Preparation

PROGRAMMED SCAN

Repeatedly scans between two scan edge frequencies

(scan edge memory channels P1 and P2).

This scan operates in VFO mode.

Scan

Scan edge P1 or P2 Scan edge P2 or P1

Jump

This scan operates in memory mode.

MEMORY SCAN

Repeatedly all programmed memory channels thatare not blank.

Mch 1 Mch 5

Mch 2 Mch 3 Mch 4

Mch 6Mch 7Mch 199

BLANK

8/7/2019 IC-7200 Manual

71/104

66

8SCAN OPERATION

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

2021

Programmed scan operation (VFO mode)

Programmed scan searches or signals betweenscan edge memory channels P1 and P2.The deault requencies or these memories are0.500000 MHz and 29.99999 MHz, respectively.See p. 62 or scan edges programming.

q Push V/M to select VFO mode.

w Push MODE to select the desired operatingmode.

The operating mode can be changed while scanning.

e Push TS to select a tuning step.

The tuning step cannot be changed while scanning.

(The programmed tuning unction can be turned ON

or OFF while scanning.)

r Set the [RF/SQL] control open or closed.

See the let page or squelch condition.

t Push SCAN to start the scan.

appears while scanning.

yWhen the scan detects a signal, the scan turnsOFF, pauses or ignores it depen ding on theresume setting and the squelch condition.

u To cancel the scan, push SCAN .

NOTE: I the same requencies are programmedinto both scan edge memory channels P1 and P2,programmed scan does not start.

MODE

TUNER

TS

FILTER

SPCH

V/M A/B SPLIT

M-CL

SCAN

SET

ATTP.AMP

COMP VOX

MNFRIT

1 2 3

4 5 6

7 8

050

28

181410

21 24

= 73.51.8

F-INP

M-CH/RIT

ENT

BANDGENE

9

.

AGCMW

ANFMETERNRNB

[RF/SQL]

Appears

Memory scan operation (Memory mode)

Memory scan searches through memory channel1 to 199 or signals. Blank (unprogrammed) memorychannels are skipped.

q Push V/M to select memory mode.

w Close the squelch with the [RF/SQL] control.

e Push SCAN to start the scan.

appears while scanning.

rWhen the scan detects a signal, the scan stops orpauses

Documents

IC-7200 Manual