Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
A8185A
04/16
Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
Exit DeviceInstallation Instructions
IN120
1-800-810-WIRE • www.sargentlock.com • A8185A
6/30
/12
1
2
3
4
5
6
Table of Contents
Warning ...................................................................................2
General Description .................................................................3
Hardware Specifications .........................................................3
Electronic Specifications .........................................................3
Parts Breakdown .....................................................................4
Rim Type 8877/8878 Exit Device Installation .........................7
Mortise Type 8977/8978 Exit Device Insallation ..................19
Operational Check..................................................................318
7
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16
!
Warning 1 Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Industry Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an exist-ing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC
To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:
• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door.
• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation
• Do not touch pins, leads or solder connections on the circuit boards
04/3
0/16
3 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
General Description2
Hardware Specifications3
Electronic Specifications4
IN120 Rim Exit• Latch – 3/4” throw, stainless steel
• Accepts all SARGENT rim cylinders (8877 only)
• Key override standard with 8877 (#34 rim cylinder supplied)
IN120 Mortise Exit• Latch – 3/4” throw, anti-friction, brass
• Key override standard with 8977 [#46 (1-3/4”) mortise cylinder supplied]
• Complete lockset with on-board memory
• multiCLASS SE reader and/or keypad
• ADA compliant
• Outside lever is unlocked through access control credentials only
• May be used for indoor and outdoor applications
• Exit Device always allows immediate egress
• UL Listed for panic and available UL Listed for fire-rated openings (12- option)
• SARGENT exit devices furnished for 1-3/4” standard (specify 31- and thickness for thicker doors)
• ANSI/BHMA A156.25 Listed Grade 1 Compliant
• Available with ET Trim only (many lever designs available)
NOTE: A weather-protective gasket is required for outdoor applications.
The IN120 WiFi lock offers the ease and flexibility of WiFi in a streamlined design, setting a new standard for aesthetics and performance. The IN120 uses IEEE 802.11 WiFi communication and a flexible feature set for easier, more cost-effective installations, allowing facilities to leverage their IT infrastructure to expand access control coverage to more doors. Featuring HID® multiCLASS SE™ technology, it supports heightened identity security and multiple credentials, including mobile access. SARGENT exit devices are designed with quality components to provide high security, performance and durability.
! *To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.
• Multiple time zone and holiday access scheduling
• First-in unlock or automatic unlock configuration, based on specified time schedule
• 2,400 users per lock; 10,000 event audit trail
• Privacy button
Power Requirements:
• Alkaline AA Batteries: 9V, 300mA
• Optional Hard Power (UL294 Listed Power Supply Required): 9-24VDC, 300mA
• HID® multiCLASS SE® technology offers support for the following credentials:• 2.4 GHz credential compatibility:
• 125 kHz credential compatibilty:• HID Prox®
• 13.56 MHz credential compatibility:• iCLASS® • iCLASS SE® (SIO-enabled)• iCLASS Seos®
• SIO on MIFARE® Classic• SIO on MIFARE® DESfire® EV1• MIFARE® Classic• DESfire® EV1• NFC-enabled mobile phones
• Secure Identity Object™ (SIO) on Mobile IDs (Bluetooth Smart)
• UL 294 Access Control Performance Ratings:
Destructive Attack Level I
Line Security Level I
Endurance Level IV
Standby Power Level I
• UL Listed - UL 294 Indoor Use
• CUL Listed - S319: Class 1
1-800-810-WIRE • www.sargentlock.com • A8185A 4
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Parts Breakdown5
1*
4
3
2
2a
** Specify finish
*Specifying B indicates Bluetooth® Smart option when ordering
1* IN-220-EM01-[B]IP-B Reader assembly - black plastic 1
IN-220-EM01-[B]IP-W Reader assembly - white plastic
IN-220-EM01-[B]IP-MB-xxx** Reader assembly - black plastic with metal trim
IN-220-EM01-[B]IP-MW-xxx** Reader assembly - white plastic with metal trim
IN-220-EM01-[B]IPS-B Reader assembly - black plastic
IN-220-EM01-[B]IPS-W Reader assembly - white plastic
IN-220-EM01-[B]CP-B Reader assembly - FeliCa - black plastic
IN-220-EM01-[B]CP-W Reader assembly - FeliCa - white plastic
IN-220-EM01-[B]CP-MB-xxx** Reader assembly - FeliCa - black plastic with metal trim
IN-220-EM01-[B]CP-MW-xxx** Reader assembly - FeliCa - white plastic with metal trim
IN-220-EM01-[B]IPS-MB-xxx** Reader assembly - black plastic with metal trim
IN-220-EM01-[B]IPS-MW-xxx** Reader assembly - white plastic with metal trim
2 IN-220-EM04 Mounting plate assembly 1
2a Through-bolts (#8-32 x 1 1/4”) 2
3 IN-220-EM03 Controller assembly 1
4 IN-220-EM02-B Inside cover assembly - black plastic 1
IN-220-EM02-W Inside cover assembly - white plastic
IN-220-EM02-MB-xxx** Inside cover assembly - black plastic with metal trim
IN-220-EM02-MW-xxx** Inside cover assembly - white plastic with metal trim
ITEMPART NO./ORDER
STRING DESCRIPTION QTY.
04/3
0/16
5 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
ITEM PART No. DESCRIPTION REQ’D
1 -- Cylinder Assembly (Reference Catalog for Available Cylinders) 1
-- #12-24 x 1-7/8” Cylinder Screws 2
2 -- Lever (Reference Catalog for Available Styles) 1
3 97-4105 Exit Trim (ET) With Cylinder 1
97-4106 Exit Trim (ET) Without Cylinder
52-4845 Motor Assembly (Separate - not shown) 1
4 68-7554 Chassis Assembly 1
68-7555 Chassis Assembly (Fire Rated)
68-7567 Chassis Assembly (Latch Guarding)
68-7569 Chassis Assembly (Fire Rated Latch Guarding)
5 68-4389 1/4-20 x 2-3/8” ET Screws - Screw Pack E 1
6 68-2143 #10 x 1-1/4” Chassis Screws - Screw Pack A 1
#10-24 x 3/4” Chassis Screws - Screw Pack A
7 68-3905 #8-32 x 5/16” Cover Screws - Screw Pack B 1
8 68-0406 Chassis Cover 1
68-1014 Chassis Cover (With Guarding)
8877/8878 x ET x Lever Design IN120 Rim Exit Device
Parts Breakdown (continued)
4
12
3
7
8
5
6
1
1-800-810-WIRE • www.sargentlock.com • A8185A 6
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
8977/8978 x RT x Lever Design IN120 Mortise Exit Device
ITEM PART No. DESCRIPTION REQ’D
1 -- Cylinder Assembly (Reference Catalog for Available Cylinders) 1
2 -- Lever (Reference Catalog for Available Styles) 1
3 97-4107 Exit Trim (ET) With Cylinder 1
97-4108 Exit Trim (ET) Without Cylinder
52-4845 Motor Assembly (Separate - not shown)
4 99-2401 8900 Lock Body Assembly LHR 1
99-2402 8900 Lock Body Assembly RHR
99-2403 8900 Lock Body Assembly LHR (Non-Beveled Door)
99-2404 8900 Lock Body Assembly RHR (Non-Beveled Door)
5 99-2628 Screw Pack 1
6 68-7550 Chassis Assembly LHR 1
68-7551 Chassis Assembly RHR
7 68-2143 Screw Pack (A) 1
8 68-0407 Chassis Cover 1
9 68-4389 1/4-20 x 2-3/8” ET Screws - Screw Pack E 1
10 68-3905 #8-32 x 5/16” Cover Screws - Screw Pack B 1
2
5
Parts Breakdown (continued)
13
4
69
7
8
9
10
04/3
0/16
7 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
• Check hand of door.
The exit device is non-handed and the trim is field reversible.
• Door should be fitted and hung.
1. If mullion is used, install prior to installing hardware.
2. Doors should be pre-prepped (recommended).
3. Use appropriate templates:
• IN120 template A8214 (wood and metal).
• Exit installation instructions A6770.
Note: Instruction examples show wood door installation.
For metal doors, route cables inside door.
Left HandReverse
LHROutside
Inside
Right HandReverse
RHR
Fig. 1A
Installation Instructions for 8877/8878 Rim Exit
A. Verify Hand and Bevel of Door
1 Door Preparation
B. Verify Product Label
C. Door Preparation
6
Outside of Door Inside of Door
Cylinder Hole
Door PositionSwitch
Lever Hole
ET Through Bolt Hole
ET Through Bolt Hole
Trim Lever Hole
ET Through Bolt Hole
Wire Run Channel (Wood Door)
Cylinder Hole
Through Bolt HolesThrough Bolt Holes
Fig. 1B
Remote Power
Remote Power
1-800-810-WIRE • www.sargentlock.com • A8185A 8
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Wood doors have 3/8” raceway to controller cutout and metal doors have 3/4” raceway to the controller cutout.
Refer to template A8214.
1. Insert connector end of DPS through the raceway on the latch edge of the door (Fig. 2A).
Note: For metal doors, use DPS Collar.
2. Push DPS firmly into place by hand.
IMPORTANT: DO NOT TAP SWITCH WITH ANY TOOL.
DPS (Door Position
Switch)
Collar is used onlywith metal doors
DPS (Door Position
Switch)
2 Install Door Position Switch (DPS)
04/3
0/16
9 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
3 Mount Exit Device Chassis
NOTE: Exit chassis harness consists of a 6-pin female connector and two different-sized ground lugs (Fig. 3A)
1. Feed 6-pin connector and larger ground lug straight through to outside of door (Fig. 3A, B) while feeding smaller ground lug into wire hole, up through wire channel and out through inside of door (Fig. 3C).
DO NOT PINCH THE WIRE HARNESS.
2. Begin to secure the exit chassis with through bolts to the ET trim using (2) 1/4 -20 x 2-3/8” flat head machine screws. Do not fully tighten at this time.
Inside of Door
(2) 1/4 x 2-3/8”Flathead MachineScrews (secures ET)
Exit ChassisFig. 3A
Fig. 3B
Outside of Door
Inside of Door
Fig. 3C
1-800-810-WIRE • www.sargentlock.com • A8185A 10
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
NOTE: For exterior applications, use ET gasket (52-0263) to seal between ET escutcheon and outside door surface.
A. Connect motor harness adapter to chassis harness connector (Fig. 4A).
B. For wood doors: Route ET wire harness connector through the cylinder hole, up and through the wire run channel to the controller cutout.
For metal doors: Route ET wire harness through the cylinder hole out the controller cutout.
C. Pass top ET trim mounting post through chassis harness ground lug.
D. Ensure ET spindle engages the lower hub of the exit chassis.
4 Mount Exit Trim (ET)
Inside of Door
Fig. 4B
Outside of Door
Fig. 4A
A
B
C
D
04/3
0/16
11 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
To comply with UL certifications and for security:
1. Fully tighten (2) chassis through bolts.
2. Fasten exit chassis to door using (4) #10 wood screws (for wood door) or (4) #10-24 machine screws (for metal door).
6 Secure Exit Chassis
(4) #10 Wood Screws or #10-24 Machine Screws
Inside of Door
(2) #12-24 x 1-7/8”Flat Head Screws (Through-bolts Cylinder to Chassis)
Fig. 6
For devices without cylinder, go to Step 6 - Secure Exit Chassis.
1. While installing the rim cylinder, support the tail piece of the cylinder, verifying its engagement with the top hub of the exit chassis.
Note: Be sure ET harness is clear of cylinder and tailpiece.
2. Secure the cylinder by through-bolting the cylinder through the exit chassis using (2) #12-24 x 1-7/8” connecting screws (see Fig. 6).
3. Verify that the key retracts latchbolt.
Position cylinder so that the SARGENT logo is right-side up.
Correct Incorrect
Fig. 5B
5 Install Cylinder
Fig. 5A
1-800-810-WIRE • www.sargentlock.com • A8185A 12
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Secure chassis cover to chassis using (4) #8-32 x 5/16” oval head machine screws (Fig. 7).
7 Install Chassis Cover
Fig. 7
NOTE: Cable lengths exaggerated for illustrative purposes.
04/3
0/16
13 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
8 Outside Reader and Mounting Plate Installation
Fig. 8
1. Orient the reader so the LED lens is at the top.
2. Feed the cable/connector through the door (from outside to inside).
3. Install the reader to the outside of door by aligning the mounting posts with the door preparation holes.
Hold the reader flush against door while ensuring proper alignment.
1-800-810-WIRE • www.sargentlock.com • A8185A 14
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Inside of Door Gasket*
Inside Mounting Plate
Through-bolts
Ground wire (Lock Body)
Fig. 9B Fig. 9C
4. Next feed the cables/connectors through the inside mounting assembly (and gasket if required*).
5. Insert and partially tighten (2) through-bolts prior to installation of connectors.
NOTE: Cable lengths exaggerated for illustrative purposes.
9 Outside Reader Installation (Continued)
6. Secure ground lug with #6-32 machine screw (Fig.9C).
*Gasket is required for outdoor installations.
If installing with gasket; separate gasket from mounting plate to feed cables/connectors through holes as indicated (Fig. 9b).
Once cables/connectors are fed through, reattach gasket to mounting plate.
04/3
0/16
15 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
1. Tuck excess cable into wire hole on inside of door.
2. Secure the mounting assembly while ensuring proper alignment of outside reader and fully tighten the (2) through- bolts on the inside of the door to secure the reader and plate to the door.
Secure the following connectors to their respective terminals (Fig. 9A, B):
A. Secure the 4-pin DPS connector.
B. Secure the 10-pin lock body assembly connector.
CAUTION - Do not touch or allow debris to enter connector contacts.
Secure Mounting Plate
IMPORTANT: Do not run wires through bottom hole in plate (Fig. 9A, B) - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 9B).
C. Secure the 24-pin card reader connector (Fig. 9B).
10 Installation of Connectors
Ground Lug
DPS (4-pin)
A
Lock Body (10-pin)
Fig. 9A
B
Reader (24-pin)
Board-to-Board Connector
Fig. 9B
C
*NOTE: Optional 2-pin external 9-24VDC power connector.
9-24VDC Power*
1-800-810-WIRE • www.sargentlock.com • A8185A 16
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
11 Installation of Inside Component Assembly
1. Insert top tabs of controller into slots on mounting plate (Fig.10).
2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate.
CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.
Fig. 10
04/3
0/16
17 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
Inside Cover
Security Allen Screw
Fig. 11
12 Battery Installation
1. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.
2. After batteries are installed, there is a slight delay; then an audible “beep” will sound and the lock motor will cycle.
Before installing batteries for the first time:
Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab (Fig. 11).
AA Batteries (6)
Coin Cell Pull Tab
13 Inside Cover Installation
1. Assemble cover by hooking top edge on inside mounting plate.
2. Carefully press bottom of cover toward door without pinching any wires.
3. Secure cover utilizing security allen wrench.
1-800-810-WIRE • www.sargentlock.com • A8185A 18
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
1. Retrieve harness from end of rail.
Harness has limited travel and can be damaged.
2. Attach harness to female connector on chassis.
3. Install rail and screws per exit device instructions.
14 Installation of Rail Assembly
Fig. 11
End of 8800 Rim Exit installation instruction - proceed to Section 9 Operational Check at end of document
04/3
0/16
19 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
Installation Instructions for Mortise Type 8977/8978 Exit Device7
• Check hand of door.
This exit device is handed and is not reversible.
• Door should be fitted and hung.
1. If using a mullion, install it prior to installing hardware.
2. Doors should be pre-prepped (recommended).
3. Use appropriate templates:
• IN120 template A8215 (Field Prep Template).
• Exit installation instructions A6705.
Note: Instruction examples show wood door installation.
For metal doors, route cables inside door.
Left HandReverse
LHROutside
Inside
Right HandReverse
RHR
Fig. 1A
A. Verify Hand and Bevel of Door
1 Door Preparation
B. Verify Product Label
C. Door Preparation
Fig. 1B
Mortise
ET Through Bolt Hole
Through Bolt Holes
Door PositionSwitch
Lever Hole
ET Through Bolt Hole
Trim Lever Hole
ET Through Bolt Hole
Remote Power Remote
Power
1-800-810-WIRE • www.sargentlock.com • A8185A 20
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Wood doors have 3/8” raceway to controller cutout and metal doors have 3/4” raceway to the controller cutout.
Refer to template A8215.
1. Insert connector end of DPS through the raceway on the latch edge of the door (Fig. 2A).
Note: For metal doors, use DPS Collar.
2. Push DPS firmly into place by hand.
IMPORTANT: DO NOT TAP SWITCH WITH ANY TOOL.
Wood Frame Metal Frame
Dim 1 3/8” 3/4”
Horizontal of Strike
Door Position Switch Hole
Vertical of Strike
Dim 2(From template)
Dim 1
Fig. 2B
2 Install Door Position Switch (DPS)
DPS (Door Position
Switch)
Collar is used onlywith metal doors
Door Frame
DPS (Door Position
Switch)
Fig. 2A
04/3
0/16
21 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
Fig. 5
3 Mount Mortise & Exit Device Chassis
Inside of Door
(2) 1/4 x 2-3/8”Flathead MachineScrews (secures ET)
Exit ChassisFig. 3A
1. Slide mortise lock into door and loosely secure with (2) flat head screws.
NOTE: Exit chassis harness consists of a 6-pin female connector and ground lug (Fig. 3A)
2. Feed 6-pin connector and larger ground lug straight through to outside of door (Fig. 3A, B) while feeding smaller ground lug into wire hole, up through wire channel and out through inside of door (Fig. 3A).
DO NOT PINCH THE WIRE HARNESS.
3. Begin to secure the exit chassis with through bolts to the ET trim using (2) 1/4 -20 x 2-3/8” flat head machine screws.
Fig. 3B Detail
Latch Bolt
Chassis
Chassis Lift Lever
Lever
1-800-810-WIRE • www.sargentlock.com • A8185A 22
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
A. Connect motor harness adapter to chassis harness connector (Fig. 4).
B. For wood doors: Route ET wire harness connector through the cylinder hole, up and through the wire run channel to the controller cutout.
For metal doors: Route ET wire harness through the cylinder hole out the controller cutout.
C. Pass top ET trim mounting post through chassis harness ground lug.
D. Ensure ET spindle engages the lower hub of the exit chassis.
E. Begin to secure chassis to ET trim by partially tightening (2) chassis through bolts (Fig. 4B).
Do not fully tighten at this time.
A
B
C
D
NOTE: Cable lengths exaggerated for illustrative purposes.
E
4 Position Exit Trim (ET)
Fig. 4A
Outside of Door
Inside of Door
Partially Tighten
Fig. 4B
NOTE: For exterior applications, use ET gasket (52-0263) as a seal between ET escutcheon and outside door surface.
04/3
0/16
23 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
For devices without cylinder, go to Step 6.
1. Secure the cylinder by threading into lock body (see Fig. 5A).
2. Verify that the key retracts latchbolt.
Position cylinder so that the SARGENT logo is right-side up.
Correct Incorrect
Fig. 5B
5 Install Cylinder
To comply with UL certifications and for security:
Fasten exit chassis to door using (4) #10 wood screws (for wood door) or (4) #10-24 machine screws (for metal door).
6 Secure Exit Chassis
Inside of Door
(4) #10 Wood Screws or #10-24 Machine Screws
Fig. 6
Fig. 5A
1-800-810-WIRE • www.sargentlock.com • A8185A 24
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Secure chassis cover to chassis using (4) #8-32 x 5/16” oval head machine screws (Fig. 7).
7 Install Chassis Cover
Fig. 7
NOTE: Cable lengths exaggerated for illustrative purposes.
04/3
0/16
25 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
8 Outside Reader and Mounting Plate Installation1. Orient the reader so the LED lens is at the top.
2. Feed the cable/connector through the door (from outside to inside).
3. Install the reader to the outside of door by aligning the mounting posts with the door preparation holes.
Hold the reader flush against door while ensuring proper alignment.
Fig. 8A
1-800-810-WIRE • www.sargentlock.com • A8185A 26
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
Gasket*
Inside Mounting Plate
Through-bolts
Ground wire (Lock Body)
4. Next feed the cables/connectors through the inside mounting assembly (and gasket if required*).
5. Insert and partially tighten (2) through-bolts prior to installation of connectors.
NOTE: Cable lengths exaggerated for illustrative purposes.
8 Outside Reader Installation (Continued)
*Gasket is required for outdoor installations.
If installing with gasket; separate gasket from mounting plate to feed cables/connectors through holes as indicated (Fig. 8B).
Once cables/connectors are fed through, reattach gasket to mounting plate.
6. Secure ground lug with #6-32 machine screw (Fig.8C).
Fig. 8C
Fig. 8B
04/3
0/16
27 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
1. Tuck excess cable into wire hole on inside of door.
2. Secure the mounting assembly while ensuring proper alignment of outside reader and fully tighten the (2) through- bolts on the inside of the door to secure the reader and plate to the door.
Secure the following connectors to their respective terminals (Fig. 9A, B):
A. Secure the 4-pin DPS connector.
B. Secure the 10-pin lock body assembly connector.
CAUTION - Do not touch or allow debris to enter connector contacts.
Secure Mounting Plate
IMPORTANT: Do not run wires through bottom hole in plate (Fig. 9A, B) - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 9B).
C. Secure the 24-pin card reader connector (Fig. 9B).
9 Installation of Connectors
Ground Lug
DPS (4-pin)
A
Lock Body (10-pin)
Fig. 9A
B
Reader (24-pin)
Board-to-Board Connector
Fig. 9B
C
*NOTE: Optional 2-pin external 9-24VDC power connector.
9-24VDC Power*
1-800-810-WIRE • www.sargentlock.com • A8185A 28
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
1. Insert top tabs of controller into slots on mounting plate (Fig. 10).
2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate.
CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.
10 Install Inside Module Component Assembly
Fig. 10
04/3
0/16
29 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
Fig. 11
Inside Cover
Security Allen Screw
Fig. 12
11 Battery Installation
1. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.
2. After batteries are installed, there is a slight delay; then an audible “beep” will sound and the lock motor will cycle.
Before installing batteries for the first time:
Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab (Fig. 11).
AA Batteries (6)
Coin Cell Pull Tab
12 Inside Cover Installation
1. Assemble cover by hooking top edge on inside mounting plate.
2. Carefully press bottom of cover toward door without pinching any wires.
3. Secure cover utilizing security allen wrench.
1-800-810-WIRE • www.sargentlock.com • A8185A 30
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.04
/30/
16IN120 Exit Device
1. Retrieve harness from end of rail. Note: Harness has limited travel and can be damaged.
2. Attach harness to female connector on chassis.
3. Install rail and screws per exit device instructions. Note: This view shows rim exit device version.
13 Installation of Rail Assembly
Fig. 13
04/3
0/16
31 1-800-810-WIRE • www.sargentlock.com • A8185A
Copy
right
© 2
016,
Sar
gent
Man
ufac
turin
g Co
mpa
ny, a
n AS
SA A
BLOY
Gro
up co
mpa
ny. A
ll rig
hts r
eser
ved.
Re
prod
uctio
ns in
who
le o
r in
part
with
out e
xpre
ss w
ritte
n pe
rmiss
ion
of S
arge
nt M
anuf
actu
ring
Com
pany
is p
rohi
bite
d.
IN120 Exit Device
Operational Check8
1. Insert key into cylinder and rotate (Fig. 15A).
There should be no friction against lock case, wire harness or any other obstructions.
2. Check that the key retracts the latch.
3. The key should rotate freely.
4. Try the inside lever; ensure it retracts latch.
5. Use a valid credential* set up with the Lock Configuration Tool to unlock outside lever and retract latch.
Refer to Network and Lock Configuration Tool user manual (WFMN1) for information on how to configure and program locks.
*Twenty (20) seconds after lock initialization (single beep with lock motor actuation).
Note: The credential should approach the inscription on the reader as indicated (Fig. 15B) to ensure the credential is read properly.
Do not wave credential.
A8185A -04/16
SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.com
HID and iCLASS are registered trademarks of HID Global Corporation.
Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience.