INDEX SECTION 17 - TRANSOM/SIDELIGHT FRAMES Area... · single swing door frame with transom typical assembly 17-101 double rabbet profile shown, other frame profiles similar for glazing

Elevations:Transom - Single Swing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-101Transom - Double Swing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-102Transom - With Fixed Mullion (Impost). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-103Door Frame with Two Partial Sidelites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-104Door Frame with Transom and Sidelites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-105Door Frame with Transom and Spliced Sidelites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-106Oversize Frame with Spliced Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-107Oversize Frame with Spliced Transom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-108Transom, Sidelite and 90˚ Corners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-109Round Arch Transom Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-110Curved in Plan Typical Elevations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-111Curved in Plan Key Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-112Curved in Plan Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-113Curved in Plan Designs of Vertical Members. . . . . . . . . . . . . . . . . . . . . . . . . 17-114 thru 17-116Curved in Plan Anchoring of End Members . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-117Curved in Plan Field Connection (Oversize Units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-118Door Frame with Transom and Sidelites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-105

Construction:Corners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-201Horizontal Bar Notching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-202Intersecting Bar/Round Arch Transom Welded Assembly . . . . . . . . . . . . . . . . . . . . . . . . .17-203Butted Welded Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-204Sill Welded Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-205Mullion to Base Sill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-206Removable Transom Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-207Splined Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-208Open Frame Section Splice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-209Transom Splice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-210Removable Mullion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-21190˚ Corner - Head, Mullion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-21290˚ Corner - Sill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-213Glazing Provisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-214Glazing Provisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-215

Profiles:See Section 8 and 11

Stick Sections:Plain Sticks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-301Strike Jambs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-302Hinge Jambs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-303“B” Mullion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-304“C” Mullion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-305“D” Mullion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-306Sill. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-307

SECTION 17 - TRANSOM/SIDELIGHT FRAMES

INDEX

17-001

SINGLE SWING DOOR FRAME WITH TRANSOM

TYPICAL ASSEMBLY

17-101

DOUBLE RABBET PROFILE SHOWN, OTHER FRAME PROFILES SIMILAR

FOR GLAZING BEAD APPLICATION SEE PAGE 17-214

17-201

17-203

17-102

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data

DOUBLE SWING DOOR FRAMEWITH TRANSOM

TYPICAL ASSEMBLY


17-201

17-203


DOOR FRAME WITHTRANSOM AND IMPOST

TYPICAL ASSEMBLY

17-103


17-201

17-203

17-204


17-104


DOOR FRAME WITHPARTIAL SIDELITE(S)

TYPICAL ASSEMBLY


SIDELITES MAY BEAT BOTH SIDES ASSHOWN OR EITHERSIDE.

17-20117-201

17-205

17-204

D or C MULLIONWEB SHOWNREMOVED TOWRAP WALL

DOOR FRAME WITHTRANSOM AND SIDELITES

TYPICAL ASSEMBLY

17-105

17-203

17-204

17-204



17-201

17-201

17-203

17-30717-206

17-106


DOOR FRAME WITH TRANSOMAND SPLINED SIDELITES

TYPICAL ASSEMBLY

DOUBLE RABBET FRAME SHOWN, SINGLE RABBET FRAME SIMILAR

17-203

17-201

17-307

1" FACES ARE OPTIONAL ATSPLINED JAMBS TO MATCH2" FACES ON OUTSIDE JAMBS

17-204

11-51317-20817-201(V6)


OVERSIZE FRAMEWITH SPLICED HEADER

TYPICAL ASSEMBLY

17-107


17-307

17-201

17-209

17-206


17-108


OVERSIZE FRAMEWITH SPLICED TRANSOM

TYPICAL ASSEMBLY


THIS STYLE IS LIMITED TODOUBLE RABBET FRAMES

LOWERUNIT

UPPERUNIT

17-201

17-203

17-204

17-204

17-203

SPLICE17-210

SPLICE17-210

SPLICE17-210

SPLICE17-210

17-307

17-204

17-203

DOOR FRAME WITH TRANSOM,SIDELITES AND 90˚ CORNERS

TYPICAL ASSEMBLY

17-109

DOUBLE RABBET PROFILE SHOWN,OTHER FRAME PROFILES SIMILAR

FOR GLAZING BEAD APPLICATION SEE PAGE 17-21417-201

17-212

17-204

17-21217-204

17-213

17-213

17-110

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataROUND ARCH TRANSOM FRAME

D

D

A

F

B

W

H

RABBET SOFFIT RABBET

1/2"

3/8" 5/8"

E

SECTION "D"

ROUND ARCH TRANSOM FRAME

17-203

FACE

C

G

WagonWheel

Fillet BasketHandle

RoundArchover

Sidelites

ARCH RADIUS (A)

RADIUS POINT OFORIGIN (B)

RADIUS POINT OFTERMINATION (C)

ARCHED FRAMESECTION PROFILE (D)

HEIGHT OF ARCH (E)

WIDTH OF ARCH (F)

BEAD REQUIREMENTS (G)

OVERALL HEIGHT OFUNIT (H)

OVERALL WIDTH OFUNIT (W)

FOR GLAZING APPLICATION SEE PAGE 17-214

DOUBLE RABBET PROFILE SHOWNOTHER FRAME PROFILES SIMILAR

OTHER ARCHEDFRAMES

IMPORTANT

ALL DIMENSIONS WHERE ALPHACHARACTERS ARE SHOWN MUSTBE SUPPLIED WITH YOUR ORDER.

“SEGMENT CONSTRUCTION”TYPICAL ELEVATIONS

CURVED IN PLAN FRAMES

17-111

PLAN VIEW

TYPICALELEVATIONS

PLAN VIEW

Option A Option B

Option C

Page 17-116 Page 17-116 Page 17-116 Page 17-116

Page 17-114 Page 17-114

Page 17-115 Page 17-115

The Following Pages List Information Required, Formats To Use, And Examples.

TYPICALELEVATIONS

Option D(Jamb)

(Jamb)Option D

Page 17-117 Page 17-117

Page 17-117 Page 17-117

Page17-118

17-112

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataCURVED IN PLAN FRAMESKEY PROPERTIES

Major Chord Length (C)

Radiu

s (R)

EnclosedAngle

SegmentEnclosed

Angle

Dashed linerepresentsArc Length (L)

The segmented method maintains the use of flat glass versus "curved in plan" shape.

The following information is important in determining Curved in Plan segment construction.This information is necessary in establishing segment lengths and any closure trim thatmay be required.

1. (R) = Radius taken to inside or outside of frame.2. (C) = Major Chord Length (C = Chord Length at Segment)3. (L) = Arc Length4. ( ) = Enclosed Angle ( = Segment Enclosed Angle)

Determining inside chord lengths are arrived at from the use of the following "propertiesof a circle" formulas. Note: Use of trigonometry tables or a calculator with trig functionsis necessary.

C = 2R sine ( /2)L = .017453R

( )

( )

Inside Chord Length

s

s

C = 2R sine ( /2)s s

s

(Inside) C

s

Fig. 1

These formulas will yield the inside chord length C (Inside) and overall frame width or centerline to centerline dimension of vertical tubes depending on selected option A, B,or C. Using this result the segment length is determined by subtracting the predetermined1" faces from the inside chord length. A similar calculation will solve for the outside chord length C (Outside) and when subtracting the previous solved segment length we now havedetermined the outside face dimensions of frame or tube.

s

s

Outside Chord Length

SegmentLength

Cs (Outside)

CALCULATIONS EXAMPLECURVED IN PLAN FRAMES

17-113

(Inside)

(Outside)

35.66"

38.56"

1.45"

1"

35.66"

37.66"

1.45"

1"

Outside face

50 ft.

40 ft.

36 ft.

30 ft.

24 ft.

20 ft.

RadiiInside Face

Frame Jambs Tube Sections

Inside Face Outside faceEnclosed

Angle

45˚ 1"

40˚

35˚

30˚

25˚

1.45" 2" 2.90"

20˚

1"

1"

1"

1"

1"

1.40" 2" 2.80"

2"2"

2"

2"

2"

1.35" 2.71"

1.30" 2.60"

1.25" 2.50"

1.20" 2.40"20

25

3

30

40

45

If there is a door opening occuring in the curved in plan opening it would receive the initial attention since most likely a standard size door opening width is being scheduled.Using the scheduled nominal door opening and working to the centerlines of each jambwill result in changes for the calculations at the remaining segment lengths for the adjacent units or lites. (Note: If a door opening is required, indicate swing and also which rabbet will be receiving glass in adjacent lites).

We have prepared the schedule below with some typical radii and enclosed angles to showthe relative dimensions of frame or tube faces that result based on 534 frames in afive lite wide configuration with all openings being equal in width. Fig.1 on 17-112 illustratesthis situation.

This length now will be used to determine37.66" - 2" = 35.66". (Segment Length)length less the two 1" inside frame faces.The segment length is the inside chord

Using = 2R sine (9/2) we get

Given: Enclosed Angle ( ) = 45 degrees

= 37.66 in. (inside chord length)

Radius (R) = 20 ft. (240")

2(240 in.) sine (4.5)

= 45/5 segments

chord length and segment length and dividetake the difference between the outsideTo find the outside frame face dimension

= 38.56 in. (outside chord length) = 2(240 + 5.75 frame depth) sine (4.5)Using the previous formula we get:we need to calculate the outside chord lengthTo find the outside frame face dimensions

outside frame face dimensions.

= 9 degrees per segment

sC

sC

Ceco offers four basic designs which result in a segmented appearance. In all cases the frames must be welded corner construction with horizontal members butted to verticals.

that by two.(38.56 - 35.66)/2 = 1.45 in.

Fig. 2

sC

Below are some sample calculations using data from the schedule above and instructions fromPage 17-112.

17-114

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataCURVED IN PLAN FRAMESDESIGN OF VERTICAL MEMBERS

OPTION AIndicates the use of a framesection with either 1" or 2"faces at both front and back.When these frames are installedto follow the required arc, theresulting gap between frames is covered with special bentplates, screw attached.

16 gage special bentplate by Ceco with#8 x 1/2" PHSMS16" O.C.

Inside Chord Length

Segment Length

1"


DESIGN OF VERTICAL MEMBERSCURVED IN PLAN FRAMES

17-115

OPTION BIllustrates individual frames butin this case they are providedwith 1" faces on one side anda special face on the oppositeside. The joining of the segmentedframes can be accomplished byeither splines or field tack weldingand filler.

Special Face

1"

Inside Chord Length

Segment Length


17-116

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataCURVED IN PLAN FRAMESDESIGN OF VERTICAL MEMBERS

OPTION CIndicates a special vertical tubesection with a 2" face on oneside and a special face on theother side. Using this make-upand shop assembling multipleunits to shipping size limits(10'-0" x 8'-0"), a fieldconnection similar to that shownon 9-118 is used for final fieldassemby.

Segment Length

Inside Chord Length

1" 1"

Special Faces


ANCHORING CONDITIONS OF END JAMBSCURVED IN PLAN FRAMES

17-117

OPTION DIllustrates a detail of a framecontour and anchoring conditionat end jambs. This contour willbe influenced by the wall make-up and anchor selection.

Special Face


Segment Length

1"

Inside Chord Length

Inside Chord Length

1"

Segment Length

Outside Chord LengthSpecial Face

5/8"

Stud Anchor

Masonry Anchor

17-118

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataFIELD CONNECTION OFOVERSIZE OPTION C FRAMES

Notch horizontalmembers to clearstops of vertical members.

OPEN FRAMESECTION

CLOSED FRAMESECTION

(4) #10 SMS atclosed section.CTSK for exposedfastener (FHSMS opt.)when specified.

(2) 1/8"SteelChannels

Temporary SpreaderIf Required

KD BORRWED LIGHT

17-119

CORNER ASSEMBLIESTYPICAL WELDED

17-201

WELDING TYPE V-6

BUTTED WELDED CORNER

1. Cope head as shown.

2. Clamp header and jamb at 90.Weld both faces continuously.

3. Grind outside faces smooth and paint.

MITERED WELDED CORNER

5. Spot paint

4a. If weld penetration occurs,

4. Weld the entire web seam (including the seams

3. Dress the face-miter seam (exterior) and spot paint.

2a. Grind the exterior face and fill as necessary.

2. Weld the entire face-miter seam from the inside.

1a. Clamp the head and jamb at 90˚.

1. Miter-saw the ends of the head and jambs at 45˚.

that cap the wall.and jambs. It can be used on framesand continuous backbend at the headReference: This corner has a full

from the backside, with a continuous weld bead.between head and jamb rabbets, stops, and soffits)

(Note: The face dimensions of the head and jamb have

Weld is to penetrate to exterior.

file smooth.

to be equal.)

HEAD

JAMB

2

4

CSF clipsrequired(welded)

CSF clipsnot requiredwhen splinesare used.

Note:

WEB SHOWN REMOVEDFROM JAMB TO WRAPWALL

17-202

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataNOTCHED HORIZONTAL BAR

NOTCH TOFIT STOP

SEE PAGES 17-203 and 17-204 FOR ASSEMBLY

1. COPE HORIZONTAL BARS AS SHOWN.

2. CUT VERTICAL MULLIONS TO REQ'D LENGTH.

AND ROUND ARCH TRANSOM ASSEMBLYTRANSOM BAR ASSEMBLY

17-203

1. COPE TRANSOM BAR AS SHOWN ON PAGE 17-202.

2. CUT JAMB TO REQUIRED LENGTH.

3. WELD BOTH FACE SEAMS FROM THEOUTSIDE AND GRIND SMOOTH.

4. SPOT PAINT.

1. WELD BOTH FACE SEAMS OF ARCH AND JAMBS FROM THE OUTSIDE AND GRIND SMOOTH.

2. SPOT PAINT.

3. TRANSOM ASSEMBLY INSTRUCTIONS SAME AS ABOVE ( ).

WELDING TYPE V8

TRANSOM BAR

TRANSOM JAM

ARCH

TRANSOM BAR

TRANSOM JAMB

TRANSOM BARASSEMBLY

ASSEMBLYROUND ARCH TRANSOM

V-8

17-204

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataBUTTED, WELDED CONNECTIONS

WELDING TYPE V-9

WELDING TYPE V-8

1. COPE MULLION AS SHOWN ON PAGE 17-202.

2. CUT HEAD TO REQ'D LENGTH.

3. FIT MULLION TO HEAD AND CLAMP AT 90˚.

4. WELD BOTH FACE SEAMS FROMTHE OUTSIDE AND GRIND SMOOTH.

5. WELD LENGTH OF BOTH STOP SEAMSFROM THROAT SIDE AND SPOT PAINT.

1. COPE JAMB TOP AS SHOWN ABOVE.

2. CUT HORIZONTAL BAR AS SHOWN ON PAGE 17-202.

3. CLAMP TRANSOM BARS AND MULLIONS AT 90˚.

4. WELD BOTH FACE SEAMS FROM THEOUTSIDE AND GRIND SMOOTH.

5. SPOT PAINT.

SILL SECTIONSIDELIGHT/BORROWED LIGHT

17-205

WELDING TYPE V-9

1. COPE SILL AS SHOWN ON PAGE 17-202.

2. FIT SILL TO JAMB AND CLAMP AT 90˚.

3. WELD INSIDE STOP AND BOTH FACES PER

4. SPOT PAINT.

V-6

1. BORROWED LITE SILL COPED PER PAGE 17-202.

2. CLAMP SILL AT JAMB AT 90˚ AND TACKWELD INSIDE AT STOP.

3. WELD BOTH FACE SEAMS FROM THE OUTSIDE AND GRIND SMOOTH.

4. SPOT PAINT.

WEB SHOWNREMOVED TOCAP WALL

WELDING TYPEV6,V10 or V11

17-206

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataMULLION TO SILL

FOR BASE SILLS 4" OR LESS:

1. COPE MULLION AS SHOWN ON PAGE 17-202.2. CUT SILL TO REQUIRED LENGTH.3. FIT MULLION TO SILL AT 90˚.4. WELD BOTH FACE SEAMS FROM THE OUTSIDE AND GRIND SMOOTH.

5. SPOT PAINT.

AND GRIND SMOOTH.

FOR BASE SILLS OVER 4":

2. CUT MULLION TO REQUIRED LENGTH.

4. WELD BOTH FACE SEAMS FROM THE OUTSIDE3. FIT MULLION TO SILLS AT 90˚.

1. COPE BASE SILLS AS SHOWN ON PAGE 17-202.

5. SPOT PAINT.

A

B

A

B

COMPONENTS

ASSEMBLY

ASSEMBLY

COMPONENTS

SLFA

CONNECTIONREMOVABLE TRANSOM BAR

17-207

2"

3-1/4"NOTCH

CLIP SET BACK 5/8"

1"

NOTE -NOTCH VERTICAL FOR THIS APPLICATION ONLY

CUT TRANSOM BAR TO REQUIRED LENGTH

NOTCH JAMB AS SHOWN

WELD ANGLE CLIPS (4) TO TRANSOM BAR(OMIT ONE CLIP ASSEMBLY WHEN CLOSERCORNER BRACKET IS SCHEDULED)

WELD REINFORCING PLATES TO INSIDEOF JAMB SOFFIT

FIT TRANSOM BAR INTO NOTCHED JAMBAND TRANSFER DRILL THRU ANGLECLIP INTO JAMB/PLATE (DRILL #7)

TAP FOR 1/4 - 20 MS

TBAN AND TBPL ARE 1/8" STEEL

TBAN 434

ALTERNATEUSE WHEN FRAME SOFFIT

IS LESS THAN 2-1/4"

TBPL 434

1/4" - 20 X 1/2" RHMS

TBAN 534

TBPL 534

17-208

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSPLINED CONNECTION

12' - 0"

9' - 0"

THERE ARE CERTAIN TIMES WHEN IT BECOMES IMPRACTICAL TO MANUFACTURE A SIDELITE TRANSOMFRAME AS ONE UNIT. IT NORMALLY IS WHEN THE UNIT IS TOO LARGE FOR SHIPPING OR SO LARGETHAT HANDLING COULD CAUSE DAMAGE. WHEN A UNIT BECOMES TOO LARGE, IT IS A GOOD IDEA TOBREAK A FRAME DOWN INTO SEVERAL PARTS. YOU SHOULD CONSIDER SPLITTING FRAME WHEN SIZEEXCEEDS 8' x 8' FOR LOCAL DELIVERY AND 9' x 9' FOR "OVER ROAD" TRUCK.

FOR EXAMPLE:

THE FRAME JAMB PIECES AT THE POINTS BEING SEPARATED WOULD OFTEN HAVE 1" FACES. THEYWOULD BE HELD TOGETHER BY USE OF THE SPLINES. THE "U" SHAPED PART OF THE SPLINE FITSOVER THE BACKBENDS OF THE FRAME SECTION AND ARE THEN DRIVEN INTO POSITION. FOURSPLINES ARE USED ON OPENINGS UP TO 7'-6". FIVE SPLINES ON 7-6" TO 8'-0" AND SIX ON8'-0" TO 10'-0" UNITS. THEY SHOULD BE LOCATED AT ABOUT 3" FROM EACH END AND SPACEDEVERY 2 FEET.

SPLINE JOINT

6070DOOR

OPENING

SPLICED CONNECTIONSFRAME OPEN SECTION

17-209

1. FIT CLOSER REINFORCEMENT HALFWAY INTO FRAME SECTION.

2. FIT OTHER FRAME SECTION TO BUTT JOINT.

3. TACKWELD REINFORCEMENT TO INSIDE OF FRAME RABBETS.

4. WELD FACES, GRIND SMOOTH AND PAINT.

1. FIT BACKING PLATES HALFWAY INTO ONE OF THE FRAME SECTIONS TO BE MATED, CLAMP INTO POSITION AND STITCHWELD INTO PLACE.

2. FIT THE OTHER FRAME SECTION TO BACKING PLATES, ALIGN CAREFULLY AND MATE THE TWO FRAME SECTIONS TOGETHER. CLAMP THE SECOND FRAME PIECE TO THE BACKING PLATE. STITCHWELD BOTH FRAME SECTIONS TO BACKING PLATES FROM THE INSIDE.

3. STITCHWELD (1" LONG) SEAM BETWEEN ADJOINING FRAME RABBETS FROM THE INSIDE.

4. TACKWELD BACKBENDS FROM THE INSIDE.

5. WELD THE SEAM BETWEEN ADJOINING FRAME FACES FROM THE OUTSIDE AND GRIND

SMOOTH.

6. IF WEB SEAM IS NOT CONCEALED BY IMPOST, FILL THE LENGTH OF WEB SEAM FROM THE OUTSIDE AND GRIND SMOOTH.

SPLICED CONNECTIONUSING A SLEEVE

USING PLATESSPLICED CONNECTION

NOTE: THESE SPLICES SHOULD PREFERABLY OCCUR AT INTERCONNECTING JOINT OF TRANSOM BAR AND MULLION.

16 Gage steelDim "A" = Face dimminus 3/16"

DIM "A"

10"

17-210

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSPLICED CONNECTIONBOLTED FORFIELD ASSEMBLY

CLOSED FRAMESECTION

(4)#10 SMSat closed section

CTSK for exposedfastener (FHSMS optional)when specified

Complete upperframe sectionshipped in oneunit

14 GA. STEELCHANNEL SPLICE

(2)#10 SMSat open section

Notch stop at verticalmember to clear stopof horizontal member

(2) 1/8"STEELCHANNELS

one unitunit shipped inComplete lower

splice splice splice

EXAMPLE OF FIELD SPLICE

OPEN FRAMESECTION

TemporarySpreaderIf Required

10'-0"

7'-2"

2'-10"

8'-2"

REMOVEABLE MULLION

17-211

1-3/4"

1" MIN.

13/16"

TO SUITMULLION

HEAD CONNECTION

SILL CONNECTION

HINGEJAMB

INSIDE

OUTSIDE

12 GA. STEEL REINFORCEMENTWELDED TO MULLION - TYPICAL

#12 x 1/2" FHMSAT (8) PLACES

12 GA. STEEL MINIMUMSILL MOUNTING BRACKET

SILL BRACKET IS FASTENEDTO FLOOR BY CONTRACTOR...FASTENERS TO SUIT FLOORNOT FURNISHED BY CECO

MULLION MOUNTING BRACKETIS ATTACHED TO FRAME HEADOF RABBETS BY MEANS OF(2) 3/8" PLUG WELDS (STD.)OR (4) #12 M.S. (OPT.)

A

A

HINGEJAMB

STRIKEPREP

SILLCONNECTION

REMOVABLE MULLION

HINGEJAMB

FRAMEHEAD

12 GA. STEEL (MIN.)HEAD MOUNTINGBRACKET

SLIDE MULLION INTO PLACE ANDFASTEN TO MOUNTING BRACKETSW/ #12 FHMS FURNISHED

FLOOR

1-9/16" MIN.3-9/16" MAX.

17-212

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data90˚ CORNER CONNECTIONS ATTOP AND INTERMEDIATE POINTS

WELD COMPONENTS PER 17-203

CONNECTION AT INTERMEDIATE POINT

CONNECTION AT TOP

HEAD

COPED END

HORIZONTALMULLION

90˚ CORNER CONNECTIONOF IMPOST AT SILL

17-213

WELD COMPONENTS PER 17-205

CORNERIMPOST

BRACINGSTRAP

SILL

17-214

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataGLAZING BEAD APPLICATIONS

1-15/16"RABBET

RABBET1-15/16"

RABBET1-15/16"

5/8"

5/8"

DOUBLE RABBET FRAME SINGLE RABBET FRAME

3/8" POCKET 3/8" POCKET

3/8" PANEL - 18 GA. GALV. STEEL FACE SHEETS W/ 5/16" CORRUGATED PAPER CORE

1 11 GLAZING MATERIALNOT BY CECO

GLAZING BEAD(VERTICAL and HORIZONTAL)

2

2 2

#8 -18 x 1 1/2" PERFORATED ANDDIMPLED HOLE

PANEL RETAINING BEADS(VERTICAL and HORIZONTAL)

3

3

GLAZING BEAD APPLICATION

PANEL RETAINING BEAD APPLICATION

"TGB" GLAZING BEAD STICK AVAILABLE IN 10'- 0" LENGTH, PRIME PAINTED

18 GA. GALVANIZEDSTEEL

Phillips Oval Head TEK Screw

GLAZING BEAD DETAILS

17-215

EQUAL

EQUAL

8" ON CENTERS

1. Will be set hard against the inside soffit (unless it is single rabbet or requested differently)of the frame with one screw unless customer specifically indicates that the bead needs to

2. When bead is requested to be set, pocket size must be given. Horizontal pieces run

3. No hole will be spaced greater than 4-1/2" from the end of the bead.

This standard reflects the procedure that will be used by Ceco Door when this product isbeing fabricated. Any deviation to this standard must be communicated at the time an order isplaced with Ceco.

GLAZING BEAD STANDARD

NOTE: CUT GLAZING BEADS SO DISTANCE FROM EACH END TO FIRST HOLES ARE EQUAL BUT NOT EXCEEDING 4-1/2".

from rabbet to rabbet. Vertical pieces will butt inside the two horizontal pieces.Bead will be attached using oval head TEK screws.

be set with a pocket.

PLAIN 1”, 2” AND 4” FACESSERIES SU & SQ STICKS

17-301

DOUBLE RABBET PROFILE SHOWN - OTHER "SQ" PROFILES ARE AVAILABLE - STANDARD STOP IS 5/8" HIGHOTHER FACE DIMENSIONS ARE AVAILABLE FROM PRODUCTION

SU (stock) 10' - 4

"

DEPTH

DEPTH

DEPTH

1" FACE

2" FACE

4" FACE

SQ or Special SU 10' - 0

"

SU (stock) 10' - 4

"

SU (stock) 10' - 4

"


"


"

17-302

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSERIES SU AND SQ STICKSTRANSOM LOCK JAMBS2” AND 1” FACES

41.8

1"

41.8

1"

SQ o

r Sp

ecia

l SU

10'

- 0

"

2" FACE 1" FACE

L

STRIKE C

STRIKE CL

SU (

sto

ck)

10' -

4"

SQ o

r Sp

ecia

l SU

10'

- 0

"

SU (

sto

ck)

10' -

4"

WITHOUT NOTCH

5/8" HIGH. OTHER FACE DIMENSIONS ARE PROFILES ARE AVAILABLE - STANDARD STOP ISDOUBLE RABBET PROFILE SHOWN - OTHER "SQ"

AVAILABLE FROM PRODUCTION

TRANSOM HINGE JAMBS2” AND 1” FACES

SERIES SU & SQ STICKS

17-303

31"

33"

34"

31"

33"

34" 33

"33

"31"

34"

34"

31"

6'-8

"

7'-0

"

7'-2

"

6'-8

"

7'-0

"

7'-2

"

9"9"

2" FACE 1" FACE

DEPTH DEPTH

SQ o

r Sp

ecia

l SU

10'

- 0

"

SU (

sto

ck)

10' -

4"

SQ o

r Sp

ecia

l SU

10'

- 0

"

SU (

sto

ck)

10' -

4"

DOUBLE RABBET PROFILE SHOWN - OTHER "SQ"PROFILES ARE AVAILABLE - STANDARD STOP IS5/8" HIGH. OTHER FACE DIMENSIONS ARE AVAILABLE FROM PRODUCTION

FOR 1-3/4" DOORS

4-1/2" HIGH x .134" THICKTEMPLATE BUTT-HINGES.CONVERTIBLE FOR .180THICKNESS.

WITHOUT NOTCH

17-304

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data“B” MULLION PROFILE AND STICKS

MULLION STICK

HAT SECTION

FRAME SECTION

1. PLACE HAT SECTION IN THROAT OF FRAME.

2. 1" FILLET WELD SEAMS AT 6" CENTERS (STAGGERED).

3. GRIND WELDS SMOOTH AND PAINT.

"B" MULLION PROFILE

NOTE: WHEN ASSEMBLING THE "B" MULLION IN SIDELITE OF BORROWED OR TRANSOM FRAMES, THE EXPOSED SEAM SHOULD BE FILLED AND GROUND SMOOTH.

DEPTH

1-15/16"

6"

6"

5/8"

5/8"

1-15/16" DOOR RABBET


"

SU (stock) 10' - 4

"

“C” MULLION PROFILE AND STICKS

17-305

MULLION STICK

"C" MULLION PROFILE

AVAILABLE WITH PREPARATIONSFOR 4-1/2" OR 5" HINGE ORANSI 4-7/8" STRIKE.

THIS PROFILE LIMITED TO THEFOLLOWING PROFILES ONLY:4-3/4", 5-3/4", 6-3/4", 7-3/4" AND 8-3/4".

1-15/16"5/8"

5/8"

DEPTH

SU (stock) 10' - 4

"

17-306

Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data“D” MULLION PROFILE AND STICKS

"D" MULLION PROFILE

MULLION STICK

5/8"

5/8"

1-15/16"

SU (stock) 10' - 4

"


"

SERIES SU AND SQFRAME SILL BASES

17-307

DEPTH VARIES

12" (STANDARD)OR

TO SUIT (SPECIAL)

12" (STANDARD)

TO SUIT (SPECIAL)OR

DEPTH VARIES

SU & SQ

SQ

3PC. CONSTRUCTION FOR FACESOVER 4"

2PC. CONSTRUCTION FOR FACESOVER 4"

1-1/2" WIDE BRACING STRAP (16 GA.)WELD TO SILL O.C. AS REQUESTED

14 GA. GALV. STEELSTOCK LENGTH: 8'-4"PRIME PAINTEDSHIPPED IN COMPONENTPIECES

*WELDING TYPEV10

*WELDING TYPEV10

* SILLS 3" THRU 12" USE TYPE V10 WELDAT JAMB (SAME PROCEDURE AS TYPE V6WELD. REFER TO 17-205)

Documents

INDEX SECTION 17 - TRANSOM/SIDELIGHT FRAMES Area... · single swing door frame with transom typical assembly 17-101 double rabbet profile shown, other frame profiles similar for glazing