INGERSOLLAAND. 7113.20 PUMPS H …...7113.20 Sheet 102 March, 1992 Cancels 7113.20, Sh. 102, dated Sept., 1989 INGERSOLL-RAND® PUMPS H MOTOMPUMP HC CRADLE PUMP Dom. Exp. Dis t. o

7113.20 Sheet 101

September, 1989 Cancels 7113.20, Sh. 101,

dated Jan., 1989.

INGERSOLLAAND. PUMPS H MOTOMPUMP

HC CRADLE PUMP

TABLE OF CONTENTS

Dom

. E

xp.

Dis

t. o

n 3

5C.

TITLE SHEET General Information 101 Application 101 Pressure-Temperature Ratings 101 Back Standard Materials 102 Standard Construction Table 102 Back Performance Curve 201

TITLE SHEET Engineering Data 301 Motorpump, Motor Data 301A Interchangeability Data 302 Shipping Weights 303 Mechanical Seals 304 Flange Loading Tabulation 305 Cross Section and Parts List 401 General Arrangement Drawing Index 501 Price Sheets 701

FORMS

Bulletin 70719-C I/B & P/L SPAD-27-D

Descriptive Sheet—H Motorpump) 70721 Descriptive Sheet—HC (Cradle Pump) 70729

GENERAL INFORMATION

The H/HC pump line is a standard for water service. The pumps are end suction, single stage, back pull-out construction. Maximum interchangeability has been built into the H/HC pumps. The back pull-out construc-tion and maximum interchangeability combine to pro-vide easy maintenance. In addition, the casing wear rings and shaft sleeves are easily replaced.

Twenty-four pumps give complete hydraulic coverage up to 1800 GPM and 390 ft total head. Twelve pumps are designed for 3500 RPM and twelve pumps are designed for 1750 RPM. Pump sizes range from 1" discharge to 5" discharge.

All H/HC pumps are centerline discharge, foot-mounted construction. Closed impellers are used for maximum efficiency. Shaft deflection is limited to .002" at the face of the stuffing box. Double volute casings are used where necessary to reduce radial hydraulic thrust. The stuffing box cover is rabbet fitted to the casing and the bearing frame for positive alignment. A confined gas-ket is used. The stuffing box on HC pumps is extra deep and will accommodate 5-rings of packing plus a lantern ring or a variety of mechanical seals.

The H2 motorpump is a compact close-coupled unit which has a low initial cost and can be installed in a minimum amount of space. Baseplates and couplings are not required so alignment problems are eliminated. H2 motorpumps are offered in 6" through 10" impeller diameters with a built-in mechanical seal. Packing is not available. H2 motorpumps utilize an industry standard (JM/JP) shaft extention motor which allows excellent motor availability and flexibility. H pumps in impeller diameters 12" and 15" are available with packed box or mechanical seal construction and utilize an Ingersoll-Rand proprietory motor shaft.

The HC pumps are cradle mounted and can utilize standard shaft foot mounted motors or a variety of other drivers. Cradle mounted pumps use permanently grease lubricated bearings (oil lubrication is available) and have a rugged heavy duty bearing frame. Both standard and spacer couplings are available in addition to other optional features.

APPLICATION

H/HC pumps are designed for general water service but can be used wherever Col. B & Col. C pumps are required. The 3500 RPM units with 9" impellers give hydraulic coverage previously reached only by multi stage units. Typical applications include chilled and hot water circulation, condensor water, small boiler feed ser-vice, bulk oil station transfer, process or machinery cool-ing water circulation, spray water pumps for air washers, air pollution control, large industrial washers, or paint

spray booths. All industrial areas—utilities, metal fabri-cators, plastic fabricators, paper mills, machine tool manufacturers, primary metal producers, chemical plants and commercial buildings—have requirements for cooling and heating water, or spray water for washing. Now most industries are aware of the requirements to return clean water to the environment so they need pumps to feed and circulate this water to cleaning devices. As such all of these industries have H/HC applications.

INGERSOLL-RAND COMPANY, PUMP GROUP, ALLENTOWN, PA. 18105 (OVER)

RATINGS, MATERIALS and

STD CONST.

PRESSURE-TEMPERATURE RATINGS

Pump

PRESSURE RATINGS' TEMPERATURE RATINGS't

Maximum Working Pressure

Maximum Hydrotest Pressure

Maximum Suction Pressure

Standard Temperature

Maximum Temperature with

Cooled box'

1 1/2x1x6 2x1 1/2x6 2 1/2x2x6

124x3x6

125psi 125psi 125psi 125psi

185psi 185psi 185psi 185psi

** ** ** **

250°F 250°F 250°F 250°F

250/400°F 250/400°F 250/400°F 250/400°F

2x1x8 2x1 1/2x8

• 133x2x8 • 1:14x3x8 • 05x4x8

150psi 150psi 150psi 150psi 150psi


** ** ** ** **

250°F 250°F 250°F 250°F 250°F

250/400°F 250/400°F 250/400°F 250/400°F 250/400°F

• 2x1 1/2x9 • 3x2x9 • 04x3x9

200psi 200psi 200psi

300psi 300psi 300psi

** ** **

250°F 250°F 250°F

250/400°F 250/400°F 250/400°F

21/2x11/2x10 3x2x10

04x3x10 • 05x4x10 • 06x5x10



** ** ** ** **

250°F 250°F 250°F 250°F 250°F

250/400°F 250/400°F 250/400°F 250/400°F 250/400°F

21/2x1V2x12 3x2x12

0 4x3x12 • 05x4x12 • 06x5x12



** ** ** ** **

250°F 250°F 250°F 250°F 250°F

400°F 400°F 400°F 400°F 400°F

• 05x4x15 • 06x5x15

150psi 150psi

225psi 225psi

** **

250°F 250°F

400°F 400°F

• Design limits shown. Stuffing box packing or mechanical seal, shaft sleeve, gland, and casing flanges must be matched to the pump application.

**Suction pressure can be any value as long as total of suction pressure and total head do not exceed maximum working pressure. ElThese pump casings have dual Volute construction. • These pumps have Impellers with Balance holes; and Wear Rings in Stuffing Box Cover. t Minimum allowable temperature = —20°F.

21-IC & 12-15" H only available pumps with cooled box. Standard Temperature only applies to 6"-10" H2

PRESSURE-TEMPERATURE RATINGS STUFFING BOX DATA

A. PACKED BOX'

Stuffing Box Pressure*

Maximum Temperature Packing Sleeve Comments

0-75 psi 3500 RPM 0-100 psi 1750 RPM 200°F STD

IR 673 Bronze

Standard Pump

0100 psi 1750 RPM 0-75 psi 3500 RPM 250°F Special*** IR 531C**

Smothering Gland Req.

101-150 psi 1750 RPM 250°F Special*** IR 531C** Smothering Gland Req.

Over 150 psi 1750 RPM Over 75 psi 3500 RPM B. Use Mechanical Seal

NOTES 'Packed Box available only on HC & 12 & 15" H pumps. *Where stuffing box pressure is less than 20 psia, internal or external flushing must be provided to the seal cage at 15 to 20 psig. With impeller balance holes and back rings S.B. pressure equals suction pressure plus 10 psi. With No impeller balance holes and back rings S.B. pressure equals suction pressure plus 0.6 discharge pressure.

**Or other hard shaft sleeve (DO NOT USE 378H ON HOT WATER SERVICE) ***Special packing consists of standard packing with alternate rings of metallic packing.

B. MECHANICAL SEAL 1. Refer to John Crane Bulletin 35-36S and 37S 2. Refer to Durametallic Form SD 129-B 3. Refer to Cameron Pump Manual

t Added

Back of 7113.20. Sheet 101.

7113.20 Sheet 102

March, 1992

Cancels 7113.20, Sh. 102, dated Sept., 1989

INGERSOLL-RAND® PUMPS

H MOTOMPUMP

HC CRADLE PUMP

Dom

. E

xp.

Dis

t. o

n 35C

.

MATERIALS OF CONSTRUCTION

pH Range 6.0-9.0 8.5-14.0

I-R Column Column B Column C

Part Name Bronze Fitted All Iron

Casing Cast Iron—Class 30B

Casing Ring Bearing Bronze Cast Iron—Class 20

Impeller Bronze' Cast Iron—Class 25B

Gasket, Casing Cover Nitrile Synthetic Fibers

Stuffing Box Cover Cast Iron—Class 30B

Shaft Sleeve Gasket Nitrile Synthetic Fibers

Shaft Sleeve (Motorpump) Stainless Steel—Type 416

Shaft Sleeve (Cradle Pump) Bearing Bronze I Carbon Steel—AISI-C1215

Shaft Carbon Steel—AISI-1045

Packing Rings2 Teflon Impregnated Synthetic Fibers

Seal Cage Glass Filled Teflon

Gland 2 Ductile Iron

Gland Bolt & Nut Stainless Steel—AISI-303

Flinger BUNA-N

Bearing End Cover Cast Iron—Class 30B

Bearing End Cover Bolt Carbon Steel—Grade B

Bearing Housing Cast Iron—Class 30B

Bearing Housing Bolt Carbon Steel—Grade B

Support Head Cast Iron—Class 30B

MATERIAL SPECIFICATIONS

General Description Specification General Description Specification

Cast Iron–Class 30B Cast Iron–Class 20 Cast Iron–Class 25B Carbon Steel–Grade B

ASTM-A48 Class 30B ASTM-A48 Class 20 ASTM-A48 Class 25B ASTM-A307 Grade B

Bronze' Bearing Bronze Ductile Iron

Alloy C87800 Alloy CA932 ASTM-A395

1. For temperatures up to 230°E Over 230°F will be alloy C87200

2. Not used/available with H2 Pumps

(OVER)

INGERSOLL-RAND COMPANY, PUMP GROUP, ALLENTOWN, PA. 18105

RATINGS, MATERIALS and

STD. CONST.

STANDARD CONSTRUCTION TABLE Construction Details STD OPT

TYPE H/H2: Horizontal, end suction, single stage, close coupled with impeller mounted on the motor shaft.

X

HC: Horizontal, end suction, single stage, cradle mounted pump flexible coupled to the motor.

X

ROTATION CW (Hydraulic Institute) when viewed from the motorside. X

Casing Vertical split, single end suction, vertical centerline discharge, self venting, back pull out, foot mounted, confined gasket, replaceable casing rings.

X

Impeller Closed type, single suction, hydraulically, statically and balanced, keyed to the shaft, and held with a cap screw and washer.

X

Stuffing Box Cover (HC only)

Suitable for 7-rings of packing or a mechanical seal, non-cooled, rabbet fit to the casing and cradle, back pull out.

X

Cooled Box X

In and Out Connections to stuffing box lantern ring. X

Shaft H2: Standard JM frame motor shaft./H: I-R proprietary shaft X

HC: Steel shaft, .002 max deflection at the face of the stuffing box. X

Stainless shaft (Cradle Pumps) X

Shaft Sleeve

Replaceable, sealed to prevent leakage under the sleeves X

Stuffing Box

H2: Built-in mechanical seal /H: Same as HC X

HC: Seven rings packing (or 5 rings plus seal cage) X

Mechanical seals, various styles and manufacturers X

Mechanical Seals

H2: Style 21/ H: Same as HC X

HC: Crane, Durametallic and others, positioned by shoulder on sleeve on Type 1, positioned and driven by set screw on Type 9.

X

Single, Double, and Unbalanced* X

Internal Flush Line X

Internal Flush with cooler or separator X

Glands (HC & H Only)

Packed Box: One piece two bolt X

Packed Box: Two piece smothering two bolt style X

Mechanical Seal: Four bolt plain style X

Mechanical Seal: Four bolt flush or vent and drain or combination X

Cradle (HC Only)

Cast iron, back pull out, rabbet fit to stuffing box cover to assure alignment. X

Bearings H/H2: Located in driver minimum 2 yrs B-10 Life X

HC: Prelubricated sealed grease, min 2 yrs B-10 Life Pump Design allows either bearing to take thrust Bearings are interchangeable between inboard and outboard bearing

X

Oil lubricated bearings (Cradle Pumps) X

Support Head (H/H2 Only)

Rabbet fit to driver and casing X

Coupling (HC Only)

Lovejoy spider type flexible coupling X

Lovejoy spacer type flexible coupling

Other types

Driver H: Special shaft design-C face X

H2: Industry standard JM design pump motor

HC: Standard horizontal foot mounted motors in NEMA frames X

Turbine Drive

Auxiliary Casing drain and discharge gage connection X Connections Condensate vent suction connection (Not available all sizes. Ref Back Sheet 703)

Suction gage connection

Drain in support head or cradle for stuffing box leakage X

Flinger H & HC: Flinger mounted on shaft to protect bearings X

Tests Hydrotest X

Performance, NPSH, witness tests

*Balanced seal not available


INGERSOLL-RAND® H/HC MOTORPUMPS/CRADLE PUMPS

7113.20 Sheet 301

January, 1989

Cancels 7113.20, Sh. 30', dated June 1, 1976.

PUMPS

ENGINEERING DATA—H/HC PUMPS

2x11/2 3x2 4x3 5x4 2x1 1/2 3x2 2x11/2 21/2x2 4x3 2x1 1 1/2x 1 4x3 x8 x8 x8 x9 x9 x6 x8 x8 x6 x6 x6 x9

Stuffing Box Data

All HC & 12 & 15" H

Sleeve aD. Stuffing Box Bore

Depth of Box

Packing Size

1 1/2"

23/46"

2 1 1/46"

11/2"

1 1 3/46"

- 23/C

3/46"

1 1/8"

1 1 3/46"

21/2"

3/46"

1 1/6"

1 13/16"

20"

5/16"

1 1/2"

25/i 6"

2 1 3/46"

4/8"

11/2" 11/2" 1 1/8"

1 1 3/46"

21/2"

3/46"

1 1/2"

25/16"

2 1 1/26"

3/8"

1 1/2"

23/46"

2 1 1/26"

1/2"

1 1/8"

11 3A6"

23/4"

23/46"

2 11/16"

~"

23/46"

2 11/16"

1/2"

Dom

. E

xp.

Dis

t. o

n 3

5C

.

3/46"

Packing Arrg't

Shaft. & Bearing Data

All HC & 12 & 15" H

Dia. (a Impeller

Dia. under Shaft Sly.

Dia. la Bearings

Dia. between Bearings

Dia. Ca Coupling

Bearing No,

Bearing Life

Shaft HP/100 RPM

WR 2 lb-ft2 (Wet) Max. Imp. Dia.

Ring + Lantern Ring

1 1/8"

1 1/4"

1.576

1 13/16"

11/2"

6308

11/2"

11/4"

1.576

1 1 3/46"

11/2"

6308

1 1/8"

11/4"

1.576

1 13A 6"

11/2"

6308

1 1/6"

1 1/4"

1.576

1 1 3/46"

11/2"

6308

743"

743"

1.183

1 7/16"

1 1/8"

6306

7/8"

2A3"

1.576

1 13/16"

1 1/2"

6308

1/2"

7/8"

1.576

1 1 3/46"

1 1/8"

6308

1 11/2"

11/4"

1.576

1 1 3/46"

11/2"

6308

1 1/2"

1 1/4"

1.576

1 1 3/46"

1 3/8"

6308

7/8"

743"

1.576

1 13/16"

11/2"

6308

1/2"

1.576

1 1 3/46"

1 1/8"

6308

4 Minimum (2) Years

1.25 2.67 1.25 1.25 1.25 2.67 2.67 2.67 2.67 1.25 1.25 2.67

.1 .16 .21 1.21 1.5 1.7 .26 .81 .91 .96 1.05

Casing Data

Suction Dia,

Discharge Dia.

Working Press. PSI

Hydrotest Press. PSI

11/2"

1"

125

185

2"

11/2"

125

185

21/2"

2"

125

185

4"

3"

125

185

2"

1"

150

225

4"

3"

150

225

5"

4"

150

225

2"

11/2"

200

300

3"

2"

200

300

2"

11/2"

150

225

3"

2"

150

225

4"

3"

200

300

Flange Rating 125 ASA Suct & Disch 4 125 Suct

4-250 Disch.

4

•

Casing Thickness 3/46" 3/46" 5/16" 11/32" VC

1/2"

17

1 1/22"

1/2"

7/16" 7/1 6" 1 %2"

Drain Size

Wear Ring Clear.

1/2 "

.010—.0

Sleeve O.D.

6, 8, 9 & 10" H Frame Size

140, 180, 210

250, 280, 320

360

11/4"

N/A

N/A

11/4"

1W

N/A

11/4"

N/A

N/A

1 1/4"

1 1/2"

N/A

11/4"

N/A

N/A

11/4"

1W

N/A

1 1/4"

1 5/8"

N/A

1 1/4"

1 5/8"

N/A

11/4"

1W

2 1A3"

1 1/4"

1 Wa"

N/A

11/4"

1W

N/A

1 1/4"

1 W

21/2"

INGERSOLL-RAND COMPANY, PUMP GROUP ALLENTOWN, PA 18105 (OVER)

ENGINEERING INFORMATION

ENGINEERING DATA-H/HC PUMPS

2 1/2x 1 1/2 x10

3x2 x10

4x3 x10

5x4 x10

6x5 x10

2 1/2x 11/2 x12

3x2 x12

4x3 x12

5x4 x12

6x5 x12

5x4 x15

6x5 x15

Stuffing Box Data

All HC & 12 & 15" H

Sleeve O.D. 1 1/6" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 11/2" 1 1/2" 1 7/8"

Stuffing Box Bore 1 13/16" 1 Wm" 23/46" 2 5/1 6" 2566" 25/16" 25/16" 23/46" 25/16" 2 5/1 6" 2 1 1/26" 2 1 1/26"

Depth of Box 2W 2W 2 1 1/26" 2 1 1/26" 2 1 1/26" 2 1 1/26" 2 1 1/26" 2 1 1/26" 2 11A 6" 2 11/16" 2 1 1/26" 2 1 1/26"

Packing Size 5/16" W1 6" Vs" 3/4" 3/4" Ye" 3/4" 3/4" 3/4" 3/4"

Packing Arrg't Ring + Lantern Ring 4

Shaft & Bearing Data

All HC & 12 & 15" H

Dia. (a Impeller 7/8" 7/6" 11/2" 11/2" 1 1/8" 11/2" 1 1/8" 11/2" 11/2" 11/2" 11/2" 11/2"

Dia. under Shaft Sly. 11/4" 11/4" 11/4" 11/4" 11/4" 11/4" 11/4" 11/4" 1W 1W

Dia. la Bearings 1.83 1.83 1.576 1.576 1.576 1.576 1.576 1.576 1.576 1.576 1.970 1.970

Dia. between Bearings 1 7/16" 1 7/16" 11,16" 1 13,116" 1 13/16" 1 13/16" 1 1 V16" 1 13/16" 1 13A6" 1 13/16" 23/16" 23/16"

Dia. (a Coupling 11/2" 11/2" 1W 11/2" 1W 1W 1W 1W 1W 1W 11/2" 1 7/8"

Bearing No, 6306 6306 6308 6308 6308 6308 6308 6308 6308 6308 6210 6210

Bearing Life fo. • Minimum (2) Years

Shaft HP/100 RPM 1.25 1.25 2.76 2.76 2.76 2.76 2.76 2.76 2.76 2.76 6.32 6.32

WR 7 lb-ft2 (Wet) Max. Imp. Dia. 2.05 2.25 2.4 2.75 4.1 4.6 4.8 5.1 5.4 5.6 7.8 8.0

Casing Data

Suction Dia. 21/2" 3" 5" 6" 2 1/2" 3" 4" 5" 6" 5" 6"

Discharge Dia. 1 1/2" 2" 3" 4" 5" 11/2" 2" 3" 5" 5"

Working Press. PSI 125 125 125 125 125 125 125 125 125 125 150 150

Hydrotest Press. PSI 185 185 185 185 185 185 185 185 185 185 225 225

Flange Rating 4 125 Suct & Disch

Casing Thickness 1 1/22" 7/16" 7/16" 15/32" 7/16" 7/1e 15/32" 1/2 " 17/32" 5/16" 5/8"

Drain Size 1/2" 1/2 " 1/2" 1/2" 1/2" 1/2" 1/2" 1/2" 1/2 " 1/2 " 1/2 "

Wear Ring Clear. 4 .010—.017

Sleeve O.D.

6, 8, 9 & 10" H Frame Size

140, 180, 210 11/4" 11/4" 11/4" 11/4" 11/4"

250, 280, 320 N/A N/A 11/2" 1W 1W

360 N/A N/A N/A N/A N/A


INGERSOLL-RAND® 7113.20 PUMPS

H/HC

Sheet 302

MOTORPUMPS/CRADLE PUMPS

January, 1989 Cancels 7113.20, Sh. 7-42,

dated April, 1980.

H INTERCHANGEABILITY CHART—MOTORPUMPS

Do

m.

Exp

. D

ist.

on

35C

.

Part

gx

LxzA

gxy1Lxz

9xZ

x'AZ

5X

CX

V

8X

L XZ

8x,/i x

Z

8XZX

E

8XE

Xt7

13xyx9

6w/1ln

6x zxe

6x

Exte

xYL LxIAZ

0 xZx£

t )(En

,

X px s

L xgx9

Z xlA

x'A

Z

txZ

xE

Z xe m

?

Z xto c s

Z x gx

9

x tixs

S xgx

9

Casing ABCDE FGH J K LMN PQR S TUVWXY Z

Casing Ring ABCD

Impeller ABCDE FGHJK LMNPQRS TUVWXY Z

" Stuffing Box Cover Ring

NONE B B A NONE AA NONE CCDD 4--A—■

Stuffing Box Cover

AVAILABLE 4— 4- B-s■ 41- C-• • NOT • A —o.

Shaft Sleeve NOTE 4--- 4-8 -• 4 • A --•

Packing AVAILABLE 4 NOT 1.4--A—$.4-8-•

Mechanical Seal • *NOTE • 4— A-1■ 4- 13-•

Gland-Packing AVAILABLE 4--- 4-B -. • NOT • A —•

Gland-Mech. Seal AVAILABLE 41--- 4- 8 11. 4 NOT P A --II.

Support Head

Motor Fr.

140-180 4—A D —•

210 4-- B ---10 E E MELMOIMIT, o a MEM Elm= 250 C C F MICIEMZIM R R MEM MCI= x x

280-320 PEI N U U

360 K P

*NOTE: SHAFT SLEEVE & SEAL INTERCHANGEABILITY IS DEPENDENT UPON FRAME SIZE NOT PUMP SIZE. FRAME S ZES 140, 180 & 210 HAVE INTERCHANGEABLE SLEEVES AND SEALS REGARDLESS OF PUMP SIZE. FRAME 250, 280, 320 ARE SIMILARLY INTERCHANGEABLE. FRAME 360 SLEEVES & SEALS ARE NOT INTERCHANGEABLE WITH ANY OTHER FRAME SIZE.

INGERSOLL-RAND COMPANY, PUMP GROUP, ALLENTOWN, PA. 18105 (OVER)


HC INTERCHANGEABILITY CHART-CRADLE PUMPS

Part

gx ix

%

9XZA

!

9nv

Az

9xE

xt,

9X

1,XZ

8xz/ t lxZ

8X

ZX

E

fixext 5x

4x8

6X4

IXZ

6xZxe

6xE

x t,

im/t lx

ViZ

lxZ

xE

1x Exi?

0 I x p

xs

0 Ix 9x 9

Z lx

% lx

z/Z

Z IxZxE 4x

3x1 2

5x4x

1 2

I

Z1 x 9x

9

9 Lxvx

9

9 tx

9x9

Casing ABCDEFGHJKLMNPQRSTUVWXYZ

Casing Ring ABCEKBOGFBDGCDGHJCDGHJHJ

Impeller A B CDEFGHJKLMNPORSTUVWXYZ

Stuffing Cover R ing

'NONE 4-B-■ A NONE A A NONE 4-C-110 4-D41. 4--A-11.

Stuffing Box Cov er

4—A---110. 4-B-10 4—C-10 4-D-* G 4-F-II■ E G G 4- J -0 4-K-110 4--H—lo

Shaft Sleeve 4— B-1. 4-A-40 4-C-• 4--A-4■ B --10.

Shaft 4-A-40.14—B---, 4-A-4. 4-D-• 4--C-10 41----C--■

Packing 4—A-11. 4---B--10 4-A-10. 4----B---, 4-C 410

Mechanical Seal 41-A-110 , 4-C-110, 41---A--10 4-- B--10 4---B---111.

Gland:Packing 4-A-■ 4-C-* 4--A-10. 4--B-10 4--- B-10

Gland-Mech. Seal 4---- B —P. 4-A-10 4-C-• 41--A --b. 4---- B --O.

Bearing Housing

4- A-P 4- B-1 4- C-10 + - F -O. 4-H-11. 4—D-110. 4—E-1). 4—E-40 41---G —10

Bearing 4-A-1. 4-A-• 4-C-I■ 4 B 4----B ----•

Cradle (Comp lete Assembly)

4-A-I■ 4-B÷ 41-C-■ 4- F-0. —So 41--G 4- H -111■ 4—D —÷ 4—E —■ 4—E —10


7113.20 Sheet 303

January, 1989

Cancels 7113.20, Sh. 303, dated May 1, 1971.

H/HC MOTORPUMPS/CRADLE PUMPS

INGERSOLL-RAND® PUMPS

Do

m.

Exp

. D

ist.

on

35

C.

H PUMP - APPROXIMATE SHIPPING WEIGHTS Pump — Motor Net Dom. Export Pump — Motor Net Dom. Export

1-1/2x1x6H —1-1/2 HP 100 110 115 2-1/2x1-1/2x10H-1-1/2 HP 155 170 180 —2 HP 100 110 115 —2 HP 155 170 180 —3 HP 110 115 120 —3 HP 160 175 185 —5 HP 130 145 150 —5 HP 185 200 210 —7-1/2 HP 140 155 165 —7-1/2 HP 195 215 225

2x1-1/2x6H —2 HP 110 125 130 3x2x1OH —2 HP 165 180 190

—3 HP 115 130 135 —3 HP 170 190 195

—5 HP 135 150 160 —5 HP 195 215 225

—7-1/2 HP 150 165 175 —7-1/2 HP 205 225 235

—10 HP 215 235 245 —10 HP 270 300 330

4x3x1OH —3 HP 215 235 240 2-1/2x2x6H —3 HP 120 135 140 —5 HP 240 260 270

—5 HP 145 160 165 —7-1/2 HP 250 270 280 —7-1/2 HP 155 170 175 —10 HP 315 345 365 —10 HP 220 245 255 —15 HP 345 380 400 —15 HP 255 280 295 5x4x1OH —7-1/2 HP 280 300 310

4x3x6H —7-1/2 HP 185 205 215 —10 HP 345 380 400

—10 HP 250 275 305 —15 HP 380 415 435

—15 HP 285 315 330 —20 HP 460 505 530

—20 HP 370 405 430 —25 HP 510 560 590 —30 HP 565 620 650

2x1x8H —3 HP 130 145 150 6x5x1OH —15 HP 410 450 470 —5 HP 155 170 175 —20 HP 490 540 565 —7-1/2 HP 165 180 190 —25 HP 540 595 620 —10 HP 235 255 265 —30 HP 595 655 685

—40 HP 650 715 745 2x1-1/2x8H —3 HP 135 150 155

—5 HP 160 175 185 2-1/2x1-1/2x12H-3 HP 215 230 240

—7-1/2 HP 170 185 195 —5 HP 240 255 265

—10 HP 240 260 275 —7-1/2 HP 250 270 280

—15 HP 270 300 310 —10 HP 315 345 360 —15 HP 345 380 400

3x2x8H —7-1/2 HP 190 205 215 3x2x12H —5 HP 250 265 275 —10 HP 260 285 295 —7-1/2 HP 260 280 290 —15 HP 290 320 335 —10 HP 325 355 375 —20 HP 375 410 430 —15 HP 355 395 410 —25 HP 425 465 490 —20 HP 440 485 505

4x3x8H —15 HP 315 350 365 4x3x12H —7-1/2 HP 295 315 325

—20 HP 400 440 460 —10 HP 360 395 415

—25 HP 450 495 515 —15 HP 395 435 455

—30 HP 500 550 575 —20 HP 475 525 550 —40 HP 555 615 640 —25 HP 525 580 605

—50 HP 700 770 805 —30 HP 580 640 665 5x4x12H —15 HP 455 500 525

5x4x8H —20 HP 425 470 490 —20 HP 540 595 620 —25 HP 475 525 550 —25 HP 590 650 680 —30 HP 530 580 610 —30 HP 640 705 740 —40 HP 585 645 675 —40 HP 695 765 800 —50 HP 730 800 840 —50 HP 840 925 970 —60 HP 795 880 925 —60 HP 905 1000 1045 —75 HP 955 1050 1100

6x5x12H —20 HP 565 620 650 2x1-1/2x9H —10 HP 275 305 320 —25 HP 615 675 710

—15 HP 310 345 360 —30 HP 670 735 770 —20 HP 395 435 455 —40 HP 725 795 835 —25 HP 445 490 515 —50 HP 870 955 1000 —30 HP 500 550 575 —60 HP 935 1025 1075 —40 HP 555 610 635 —75 HP 1095 1205 1260

3x2x9H —20 HP 405 445 460 5x4x15H —20 HP 595 650 680

—25 HP 455 505 525 —25 HP 645 705 740

—30 HP 510 565 590 —30 HP 700 770 805

—40 HP 565 620 650 —40 HP 755 835 870

—50 HP 730 805 840 —50 HP 900 990 1035

—60 HP 775 850 890 —60 HP —75 HP

965 1125

1065 1240

1115 1295

4x3x9H —30 HP 540 595 625 6x5x15 H —30 HP 760 835 870 —40 HP 595 655 685 —40 HP 815 895 935 —50 HP 745 820 860 —50 HP 960 1055 1100 —60 HP 805 885 925 —60 HP 1025 1125 1180 —75 HP 965 1060 1110 —75 HP 1185 1300 1360 —100 HP 1085 1195 1250 —100 HP 1305 1435 1500

INGERSOLL-RAND COMPANY, PUMP GROW? ALLENTOWN, PA. 18105


(OVER)

HC PUMP - APPROXIMATE SHIPPING WEIGHTS

Pump Model

Net Domestic Shipping Export Shipping

Pump Alone

Pump & St'l. Base

Pump Alone

Pump & St'l. Base

Pump Alone

Pump & St'l. Base

1-1/2x1x6 90 150 100 165 105 175 2x1-1/2x6 95 165 105 185 110 195 2-1/2x2x6 105 225 115 250 120 260

4x3x6 135 255 150 280 155 295

2x1x8 110 180 125 200 130 210 2x1-1/2x8 115 240 130 260 135 275

3x2x8 135 270 150 295 155 310 4x3x8 160 340 180 375 185 390 5x4x8 190 370 210 405 220 425

2x1-1/2x9 170 300 190 330 200 345 3x2x9 180 360 200 395 210 415 4x3x9 210 390 235 430 245 450

2-1/2x1-1/2x10 150 255 165 280 175 295 3x2x10 160 265 180 295 185 305 4x3x10 205 365 225 405 235 420 5x4x10 235 415 260 455 270 475 6x5x10 265 460 295 505 305 530

2-1/2x1-1/2x12 205 355 225 395 235 410 3x2x12 220 380 245 420 265 440 4x3x12 255 435 280 480 295 500 5x4x12 320 515 355 566 370 590 6x5x12 345 465 380 510 400 535

5x4x15 390 510 430 560 450 585 6x5x15 445 585 490 645 515 675

7113.20 Back of 303

H2 PUMPS IN 6", 8", 9" & 10" IMPELLER DIAMETERS

FRAME* SIZE A 8 C Min D F J S I

140,180,210 1.250-.002 2.19 1.50 1.874 + .002 .500 1.06 1.50 .44

250,280,320 1.625-.002 2.75 1.87 2.374 + .002 .500 1.38 2.00 .50

360 2.125-.002 3.31 2.50 2.999 + .002 .500 1.69 2.56 .56 Dom

. In

tl. D

IM. o

n 35

C

TO F IPST OBS TRUC T I ON

H USEABLE I SLEEVE

M DIA (MAX.)

N DIA. ST . BOX NOSE

.03 R. MAX.

CB DIA. A DIA.

.06 GASKET

4 - K DIA. STUDS LOCATED ON L DIA. B.C. (EOUALL Y SPACED) STRADDLE CI PIES

1- B DIA.

C G DIA.

MAX. GLAND AT STUDS

GROUP 1

11/2x 1 x 6

2 x 11/2x6

21/2x2 x 6

4x3x 6

2 x 1 x 8

2 x1 1/2x8

21/2x1Y2x10

3x2x10

INGERSOLLAAND. PUMPS

H MOTOMPUMP

HC CRADLE PUMP

7113.20 Sheet 304

May 22, 1992 Cancels 7113.20. Sh.304,

dated May 1992

SEALING CHAMBER DIMENSIONS, INCHES

*Seal size is based on motor frame/shaft size.

ALL HC PUMPS & H PUMPS IN 12" & 15" IMPELLER DIAMETERS

LEGEND SEAL SIZE

GROUP 2

3x2x8 6x 5x 10

4x3x8 21/2x1 1/2x12

5x4x8 3x2 x 12

2x1Y2x9 4 x3x12

3x2x9 5x4 x 12

4x3x9 6x 5x12

4x3x 10

5x4x 10

GROUP 3

5x 4x 15

6x 5x 15

PUMP GROUP A B CB CG D E

FLUSW GLAND

F

STND' GLAND

G HJKL M N

1 1.125 (-.002) .88 1.812 (+.005) 1.750 (4-.002) 2.38 2.12 .75 .50 1.12 125 .38 3.50 4.38 2.373 (-.003) 2 1.500 (-.002) 1.25 2.312 (+.005) 2.125 (+.002) 2.69 2.31 .75 .50 1.38 1.06 .38 4.00 4.88 2.873 (-.003) 3 1.875 (-.002) 1.62 2.687 (+.005) 2.625 (+.002) 2.69 3.00 .81 .56 1.38 1.00 .50 4.50 5.62 3.248 (-.003)

NOTE: 1. Gland & gasket furnished by I-R unless otherwise requested. 2. Flush Gland is optional.



(OVER)

DISCHARGE

SUCTION

PLAN 31

TUBE

CARBON

STEEL

1

STAINLESS

STEEL

1

3 3

1 1

3 3

5 5

1 1

1 1

H2 STANDARD SEAL MATERIALS

Service Seal Part Description

Seal Name Application Bellows

Rotating Face Spring

Stationary Seat

Metal Parts

General Service

Clean Water Natural Base

Oils Hydraulic

Fluids 212°F Max

Buna-N Carbon Stainless

(18-8) Ceramic Stainless

(18-8)

Hot Water

Service

Clean Hot Water

Light Caustics 250°F Max

Eythylene Propylene

Carbon Stainless

(18-8) Ni-Resist

Stainless (18-8)

Corrosive

Clean Service Compatible

wNiton-316SS 250°F Max

Viton Carbon Stainless

(18-8) Ceramic Stainless (18-8)

Abrasive* Services with

Suspended Solids 250°F Max


(18-8) Tungsten Carbide

'Stainless (18-8)

*For water service with high chromates or start-up protection. Not intended for slurry applications.-

HC & 12"-15" H PUMPS-SEAL MATERIALS

Seal Name

SEAL PART DESCRIPTION

Bellows 0-Ring Rotating

Face Spring Stationary

Seat Metal Parts

General Service _

Buna-N


Steel (18/8)

Ni-Resist Column B is Brass

Column C is Plated Steel

18/8 Stainless is Optional

Corrosive Viton Ceramic

Abrasive* Viton Tungsten Carbide

Hot Water Select Seal Above and use "Cooled Cover" Option

STANDARD SEAL PIPING ARRANGEMENTS

DISCHARGE SEPARATOR

PLAN 1 1A

PLAN 31 DISCHARGE TO BOX

DISCHARGE THRU SEPARATOR

TO BOX

BILL OF MATERIAL FOR SEAL PIPING ARRANGEMENTS

ITEM

PLAN 11A

TUBE

NYLON STAINLESS

STEEL

1. Separator

2. Female Reducers 1/2" x 1/4"

3. Male Connector 2 2

4. Male Elbow Connector

5. Tubing Seamless 14 " O.D.—Feet 3 3

6. 900 Elbow 1/4 F.D.S. 1 1

7. Nipple 'A x 6" Ig.-8" H/HC 1 1

8. Nipple % x 5" Ig.-6" H/HC 1 1


INGERSOLLAAND. 7113.20

PUMPS

H/HC

Sheet 305

MOTORPUMPS/CRADLE PUMPS

January, 1989

Cancels 7113.20, Sh. 305, dated April, 1980.

Dom

. Exp

. D

ist.

on

35

C.

H/HC PUMP FLANGE LOADING TABULATION FOR COLUMN "B", "C" AND "BI"

MAXIMUM ALLOWABLE FLANGE LOADS ON SUCTION OR DISCHARGE

Pump Model

FORCES — LBS MOMENTS — FT-LBS

Fxs Fx D

F YS

Fy0

F z Mx My Mz

11/2x1 x6 100 50 80 160 300 700 180 2x11/2x6 120 60 80 160 350 700

8 180 21/2x2x6 120 60 90 180 400 750 200 4x3x6 170 80 120 240 500 900 250

2x1x8 130 90 180 200 2x1 1/2x8 140 100 200 220 3x2x8 170

co 120 240

8 8 250 4x3x8 200 140 280 300 5x4x8 210 160 320 350

2x11/2x9 210 100 150 300 630 1200 1700 300 3x2x9 210 100 150 300 650 1300 1800 350 4x3x9 250 120 175 350 750 1500 2000 400

21/2x11/2x10 200 90 120 240 550 3x2x10 200 90 120 240 600 4x3x10 250 120 175 350 750

8

5x4x10 250 120 175 350 750 6x5x10 250 120 175 350 750

21/2x1 1/2x12 250 120 175 350 750

88

88

8

3x2x12 250 120 175 350 750 4x3x12 250 120 175 350 750

8 Lc)

5x11.x12 250 120 175 350 750 6x5x12 250 120 175 350 750 5x4x15 250 120 175 350 750 1500 2000 400 6x5x15 250 120 175 350 750 1500 2000 400

Subscripts "S" and "D" denote suction and dischargeflanges respectively. Valves given are for Forces or Moments acting alone at the suction or discharge flange. In combination, Forces and Moments must be reduced so that:

Fxs

Fys

Fy Fzs

+ Fz MX My MZ ‘.1.0

Fxs Max. Fx Max. Fys

Max. Fy Max. Fz Max. Mx Max. My Max. Mz Max.

Example: Assume a 5x4x8 pump is subject to the following loads:

SUCT. FLANGE DISCH. FLANGE

Fx 10 lbs. 20 lbs.

Fy 0 40 lbs.

Fz 50 lbs. 75 lbs.

Mx 110 ft-lbs. 150 ft-lbs.

My 80 ft-lbs. o

Mz o 65 ft-lbs.

By inspection all loads are less than Maximum allowable in tabulation. The following check indicates that loading is acceptable.

1020 0 40 125 260 + 80 + 65 + + + + + = .982 210 100 160 320 700 1300 1800 350

NOTE: All signs are to be considered positive regardless of direction of loading.



Documents

INGERSOLLAAND. 7113.20 PUMPS H …...7113.20 Sheet 102 March, 1992 Cancels 7113.20, Sh. 102, dated Sept., 1989 INGERSOLL-RAND® PUMPS H MOTOMPUMP HC CRADLE PUMP Dom. Exp. Dis t. o