-
INSTALLATION INSTRUCTIONS FOR PART 99-7008
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
• DIN Radio Provision with pocket• ISO Radio Provision with
pocket
A) Radio Housing B) ISO Brackets C) ISO Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
99-7008
APPLICATIONS
2003-2006Mitsubishi Outlander
CBA
• Phillips Screwdriver Panel Removal Tool orSmall Flat Blade
Screwdriver
-
Dash Disassembly
............................................................................
1
Kit AssemblyDin Mount Radio Provision with
pocket..........................................................2ISO
Mount Radio Provision with
pocket..........................................................3
Final Assembly
.................................................................................
4
99-7008
TABLE OF CONTENTS
2003-2006 Mitsubishi Outlander
-
99-7008 DASH DISASSEMBLY
Disconnect the negative battery terminal to prevent an
accidentalshort circuit.
1
Remove all (3) climate control knobs.(Figure A)
2
MITSUBISHI OUTLANDER 2003-2006
Remove (2) Phillips head screwsfrom behind the (2) outside
climatecontrol knobs. (Figure A)
3
Unsnap the top edge of the trimpanel below the Climate controls.
Itis not necessary to completelyremove this panel. (Figure B)
4
Unsnap and remove the radio/climatecontrol trim panel. (Figure
C)
5
A
B
C
1
Remove (4) Phillips head screwssecuring the radio. Unplug
andremove the radio.
6
-
2
Slide the DIN cage (supplied with radio)into the Radio Housing
from the front. (Figure A)
1
A
Slide the radio into the DIN cage until itsnaps into place.
(Figure C)
3
DIN MOUNT RADIO PROVISION WITH POCKET
B
99-7008 KIT ASSEMBLY
Secure DIN cage to radio housing bybending the locking tabs
outward.(Figure B)
2
Continue to final assembly.
C
-
3
Align the holes in the ISO brackets withthe holes in the radio.
Mount thebrackets to the radio using screwssupplied with the radio.
(Figure A)
1
A
B
Slide the radio/bracket assembly into theradio housing until it
snaps into place.(Figure B)
2
Snap the ISO trim-plate onto the front ofthe assembled radio and
housing.(Figure C)
NOTE: To remove the radio unsnap and remove the ISO trim-plate.
Using a flatblade screwdriver disengage ISO brackets from the radio
housing and slideradio out of radio housing.
3
ISO MOUNT RADIO WITH POCKET
99-7008 KIT ASSEMBLY
Continue to final assembly.
C
-
4
FINAL ASSEMBLY1 Locate the factory wiring harness in the dash
and make the connection as shown.
Metra recomends using the proper mating adapter and making the
connections asshown. (Isolate and individually tape off the ends of
any unused wires to preventelectrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for
proper operation.
Reassemble radio and dash assemblies in reverse order of
disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown
below and the instructions included with the headunit. Metra
recommends making connections as shown below; Strip, Splice,
Solder, Tape. Isolate and individuallytape off ends of any unused
wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle
chassis.All colors may not be present on all leads due to
manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-7008 FINAL ASSEMBLY
3
-
5
99-7008
NOTES
-
99-7008 INSTRUCTIONS
1-800-221-0932 www.metraonline.com© COPYRIGHT 2004 METRA
ELECTRONICS CORPORATION INST99-7008REV. 03/14/06
