Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
InstaBlak® 333 Short-Run Production Kit
Control the production of your parts with same-day blackening in-house at room temperature!
— The name you trust in metal finishing chemistry. by
The InstaBlak® 333 Short-Run Production Kit from EPI is safe and easy to use. Virtually any employee can blacken your parts without extensive training. This saves you time and money, allowing for “just-in-time” production of blackened parts.
The InstaBlak® 333 Short-Run Production Kit gives you advantages you may have thought out of your reach:
• Quick and easy – higher productivity – ready to be used at anytime
• Good corrosion resistance, 96+ hours salt spray resistance if desired
• No dimensional change• Low cost• Aesthetic appeal• Safety- No harmful fumes or hot splattering chemicals• All types of iron, steel and powdered metal• Energy saving• Anti-galling• Lubricity
The quick and easy, six to eight step process* is outlined on the next page. In just 13 minutes, the InstaBlak® 333 Short-RunProduction Kit gives you a deep, rich black finish.
Are you tired of the high minimum charges for sending out parts to be blackened by a job shop? Are you even more disturbed with the exorbitant even higher charges when youneed and request a quick turn around on your parts? Have you experienced damaged parts being returned to you from the job shop? If so, you need the InstaBlak® 333 Short-RunProduction Kit from EPI. Sending parts out is costly and produces lapses in your JIT (just-in-time) programs. TheInstaBlak® 333 Short-Run Production Kit gives you more controlover your parts and decreases lead time for your customers.
Get a fast pay back! The kit can be paid for within a few weeksby avoiding minimum charges. You have control over your partsand their quality. No waiting days for your parts to be returnedfrom a job shop.
With today’s demands for high productivity, you can nowblacken parts previously left unblackened, improving parts’appearance and their sales appeal.
17000 Lincoln Ave.New Berlin, WI 53151-27812
Call Now to Order with Your VISA or MasterCard:
(262)786-9330 or Complete the Form onPage 3 and Fax to (262) 786-9403
Step 1Clean in E-Kleen 148-Eto remove cutting fluids,coolants, oils and other soils.Five (5) minutes.
Step 5Blacken inInstaBlak 333solution forTwo (2) minutes.
Step 7Seal the finish and producecorrosion resistance by immersing in E-Tec 503.One (1) minute.
Step 8All parts to air dry.
Step 2Rinse in cold waterto remove residual cleaning solution.One (1) minute.
Step 3Activate in E-Prep 258 to prepare surface for blackening.One (1) to two (2) minutes.
Step 4Rinse in cold waterto remove residual activator solution.One (1) minute.
Step 6Rinse in cold water to remove residualblackening solution.One (1) minute.
Cold Water Rinse
E-Kleen®
148E
E-Prep® 258
InstaBlak®
333
E-Tec® 503
Cold Water Rinse
Cold Water Rinse
*NOTE: All alloys do not require the activation Step #3 and rinse Step #4, reducing the process to only six (6) steps.Process will blacken all non-stainless steel alloys.
The InstaBlak® 333 Short-Run Production Kit from EPI consists of:
• Two five gallon steel tank pails (one contains E-Tec 503 - see below)• Five five gallon plastic tank pails• One gallon container of E-Kleen® 148E liquid concentrate• One gallon container of E-Prep® 258 liquid concentrate• One gallon container of InstaBlak® 333 liquid concentrate• One five gallon container of E-Tec® 503 ready-to-use solution• One heater unit• One thermometer
Shipped with complete operating instructions.
InstaBlak® 333 uniform,rich finish improves part appearance andincreases sales appeal.The InstaBlak® 333 Short-Run Production Kitfrom EPI achieves a corrosion-resistant finish in about 13 minutes.
InstaBlak® Short-Run Production Kit Order FormPlease print out this form, complete and fax to (262) 786-9403
Name __________________________________________________________________________________________________
Billing Address:
Company ________________________________________________________________________________________________
Street __________________________________________________________________________________________________
City ______________________________________________ State/Province _________ Zip/Postal Code ____________________
Country _________________________________________________________________________________________________
Telephone _______________________________________________________________________________________________
Fax ____________________________________________________________________________________________________
E-mail __________________________________________________________________________________________________
Shipping Address (if different from above):
Company________________________________________________________________________________________________
City ______________________________________________ State/Province _________ Zip/Postal Code ____________________
Country _________________________________________________________________________________________________
Telephone _______________________________________________________________________________________________
Fax ____________________________________________________________________________________________________
E-mail __________________________________________________________________________________________________
Nearest Airport (if ordering outside the USA) ______________________________________________________________________
Credit Card Number _______________________________________________________________________________________
❑ VISA ❑ MasterCard Expiration Date (Month/Year)_____________________________________________
Kit is shipped F.O.B. New Berlin, WI 53151, USA and will be shipped the most economical manner unless you specify FedEx and give us thenearest airport when ordering from outside the USA.
17000 Lincoln Ave.New Berlin, WI 53151-2781USA2
Call (262)786-9330 to Order... Or Fill Out the
Above Form and Fax to (262) 786-9403 • e-mail: [email protected]