INSTALLATION FOG LIGHTS 2011 CR-V INSTRUCTIONS AUG 2010 · Illustration of the Fog Lights on the Vehicle INSTALLATION 1. Make sure you have the anti-theft code for the audio and navigation

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2010 American Honda Motor Co., Inc. – All Rights Re

AII 44625
FOG LIGHTS
served. AII 44625 (1008

2011 CR-V

) 0

Issue Date

AUG 2010

PARTS LIST

Fog Light Kit (With Auto Lights)P/N 08V31-SWA-100A

Fog Light Kit (Without Auto Lights)P/N 08V31-SWA-100B

Right fog light

Left fog light

Fog light harness

Switch harness

Right trim

Left trim

2 Clips

Relay

Relay bracket

11 Wire ties

4 Wire ties with clips

2 Harness tapes

6 Self-tapping screws, 5 x 14 mm

6 x 16 mm Washer bolt

6 mm Flange nut

20A Fuse

Light/turn signal switch

1 of 138V31-SWA-1000-9A

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriverFlat-tip screwdriver

Diagonal cutters

Ratchet

10 mm Socket

10 mm Wrench

Plastic trim tool T/N SILTRIMTL10

Isopropyl alcohol

Shop towel

Utility knife

Tape

Electrical tape

File

Blanket

2 of 13 AII 44625

Illustration of the Fog Lights on the Vehicle

INSTALLATION

1. Make sure you have the anti-theft code for the audio and navigation system if equipped, and write down the XM radio station presets if equipped.

2. Disconnect the negative cable from the battery.

3. Remove the front grille cover (seven clips).

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

922507AG

RIGHT FOG LIGHT

LIGHT/TURN SIGNAL SWITCH

20A FUSE

SWITCH HARNESS

FOG LIGHT HARNESS

LEFT FOG LIGHT

920501BX

7 CLIPS

FRONT GRILLE COVER

(1008) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.

4. Remove the front bumper (four self-tapping screws, six clips, and two bolts). Have an assistant help you when removing and installing the front bumper. Place the front bumper on a blanket after removal.

5. Remove five clips from the left front inner fender, and pull down the left front inner fender.

922304BG

6 CLIPS

2 BOLTS

FRONT BUMPER

4 SELF-TAPPING SCREWS

941701AB

SHORT CLIP

LEFT FRONT INNER FENDER

LONG CLIP

SHORT CLIP

© 2010 American Honda Motor Co., Inc. – All Rights Reserved. AII 44625

6. To protect the front bumper, apply masking tape to the front bumper around the left fog light opening.

7. Using a utility knife, cut along the inner line of the hole as shown. Take care not to damage the front bumper.

930901AG

FRONT BUMPER

MASKING TAPE

930902AG

FRONT BUMPERCut out.

FRONT BUMPER

HOLE INNER LINE

FRONT BUMPER

CROSS SECTION

Cut.

Cut.

(1008) 3 of 13

8. Cut off the four ribs on the front bumper as shown. Remove any burrs. Remove the masking tape.

9. From the outside of the bumper, install the left trim.

930903AG

FRONT BUMPER

FRONT BUMPER

4 RIBSCut off.

922402BG

FRONT BUMPER

LEFT TRIM

INSIDE VIEW

BUMPER OPENINGCut in step 7.

LEFT TRIM

FRONT BUMPER

PIN

PIN

Check the L mark.

4 of 13 AII 44625

10. Inside the bumper, install one clip to the front bumper.

11. Install the left fog light to the front bumper using three 5 x 14 mm self-tapping screws.

12. Repeat steps 6 thru 11 to install the right fog light on the right side of the front bumper.

922305BG FRONT BUMPER

CLIP

CROSS SECTION

FRONT BUMPER

HOLDER

922501AG

FRONT BUMPER

3 SELF-TAPPING SCREWS, 5 x 14 mm

LEFT FOG LIGHT


Routing the Fog Light Harness

13. Route the fog light harness 1-pin connector in front of the left front inner fender as shown. Plug the fog light harness 1-pin connector to the vehicle 1-pin connector.

14. Secure the fog light harness to the vehicle harness with two wire ties. Do not secure the fog light harness to the SRS harness.

15. Remove the vehicle ground bolt, and secure the fog light harness ground terminal to the vehicle ground terminal with the vehicle ground bolt just removed.

16. Secure the fog light harness to the vehicle harness with two wire ties.

941702AB

WIRE TIE

FOG LIGHT HARNESS

VEHICLE HARNESS

FRONT

LEFT FRONT INNER FENDER

FOG LIGHT HARNESS 1-PIN CONNECTOR

VEHICLE 1-PIN CONNECTOR

WIRE TIE

VEHICLE BRACKET

VEHICLE HARNESSSecure theharness with no excess slack.

SRS HARNESS Do not secure.

941703AB

FOG LIGHT HARNESS

VEHICLE HARNESS

WIRE TIE

FRONT

VEHICLE GROUND TERMINAL FOG LIGHT HARNESS

GROUND TERMINAL

VEHICLE GROUND BOLT


17. Route the fog light harness under the left headlight, and secure the fog light harness clip to the vehicle panel.

18. Secure the other two fog light harness clips to the holes in the resonator.

19. Secure the fog light harness to the front bulkhead.With a Vehicle Harness: Cut the clips off of the two wire ties with clips. Secure the fog light harness to the vehicle harness near the harness clips using two wire ties.

FRONTFOG LIGHT HARNESS

FOG LIGHT HARNESS CLIP

LEFT HEADLIGHT

VEHICLEPANEL

RESONATOR

931201AG

VEHICLE HARNESSFRONT FOG LIGHT

HARNESS

FOG LIGHT HARNESS

VEHICLE HARNESS

2 WIRE TIES WITH CLIPS

Cut off.

2 WIRE TIES

2 VEHICLE CLIPS

(1008) 5 of 13

Without a Vehicle Harness: Secure the fog light harness to the bumper beam using two wire ties with clips and one wire tie.

20. Route the fog light harness under the bumper beam towards the right side of the vehicle. Secure the fog light harness.

With a Vehicle Harness: Cut the clips off of the two wire ties with clips. Secure the fog light harness to the vehicle harness using three wire ties.

6303011B

VEHICLE PANEL

FRONT

FOG LIGHT HARNESS


WIRE TIE

FRONT

FOG LIGHT HARNESS

VEHICLE HARNESS


Cut off.2 WIRE TIES 2 VEHICLE

CLIPS

BUMPERBEAM

VEHICLE HARNESS

FOG LIGHT HARNESS

WIRETIE

6 of 13 AII 44625

Without a Vehicle Harness: Secure the fog light harness to the bumper beam using two wire ties with clips and one wire tie.

21. Using isopropyl alcohol on a shop towel, clean the bumper beam surface where the harness tape will attach.

22. Continue routing the fog light harness along the bumper beam to the right side of the vehicle. Secure the fog light harness under the bumper beam using two harness tapes and two wire ties connected together.

FOG LIGHT HARNESSFRONT

WIRE TIE

BUMPER BEAM


FOG LIGHT HARNESS

BUMPER BEAM

BUMPER BEAM

BUMPER BEAM

FOG LIGHT HARNESS

FRONT

2 WIRE TIES

2 HARNESS TAPES


23. Route the fog light harness as shown, and secure the clip on the fog light harness to the vehicle panel.

24. Secure four remaining fog light harness clips to the holes in the vehicle panel.

6303042B

FRONT

FOG LIGHT HARNESS

VEHICLE PANEL

FOG LIGHT HARNESS CLIP

FOG LIGHT HARNESS

6303053B

FRONT4 FOG LIGHT HARNESS CLIPS

VEHICLE PANEL

FRONT

VEHICLEPANEL

Installposition.

FOG LIGHT HARNESS


25. Reinstall the inner fender. With the help of an assistant, bring the front bumper close to the vehicle, and plug the fog light harness 2-pin connectors into the right and left fog lights. Reinstall the front bumper.

Routing the Switch Harness

26. Remove the driver’s dashboard under cover, turn the knob and release the pin and the clip.

922502BG

LEFT FOG LIGHT


RIGHT FOG LIGHT

FRONT BUMPER


6303080B

DRIVER’S DASHBOARDUNDER COVER

KNOBTurn.

CLIP

PIN

(1008) 7 of 13

27. Remove the driver’s dashboard lower cover (seven clips and two hooks).

28. Remove the left front side step trim (three clips).

6303071B

DRIVER’S DASHBOARD LOWER COVER

7 CLIPS

HOOK

6303090B

3 CLIPS

LEFT FRONT SIDE STEP TRIM

8 of 13 AII 44625

29. Pull back the door opening seal from around the driver’s kick panel, and remove the driver’s kick panel (two clips).

30. Lower the tilt lever. Using a flat-tip screwdriver, release one of the retaining tabs from the steering column lower cover.

6303100B

2 CLIPS

DRIVER’S KICK PANEL

DOOR OPENING SEALPull back.

6905030Y

STEERING COLUMN LOWER COVER

FLAT-TIP SCREWDRIVER

RETAINING TAB

TILT LEVER


31. Remove the steering column upper cover (two retaining tabs on each side).

32. Remove the steering column lower cover (two self-tapping screws and one screw).

6819020Y

STEERING COLUMN UPPER COVER

Push.

2 RETAINING TABS

6819030Y

STEERING COLUMN LOWER COVER

SELF-TAPPING SCREW

SCREW


33. Plug the relay into the switch harness relay block.

34. Install the relay bracket to the switch harness relay block.

35. Install the switch harness relay block on the vehicle panel using a 6 x 16 mm washer-bolt and a 6 mm flange nut.

6828010B

RELAY BRACKET

RELAY

SWITCH HARNESS RELAY BLOCK

6303130B

VEHICLE PANEL

SWITCH HARNESS RELAY BLOCK

6 mm FLANGE NUT

6 x 16 mm WASHER-BOLT

FUSE BOX

(1008) 9 of 13

36. Plug the switch harness 2-pin connector into the vehicle harness 2-pin connector. Secure the switch harness to the vehicle harness using two wire ties.

37. Push the retaining tab on the vehicle green 42-pin connector, the white 34-pin connector, and the blue 21-pin connector, and raise the lock lever on each connector. Remove the connectors from the fuse box. Close the lock lever on the vehicle white 43-pin connector, and remove the cover by sliding it away from the lock.

940903AG


SWITCH HARNESS 2-PIN CONNECTOR

WIRE TIE

VEHICLE HARNESS

FUSE BOX

SWITCH HARNESS

WIRE TIE

6303150B

FUSE BOX

FUSE BOX


LOCK LEVER

VIEWED FROM FRONT

21-PIN CONNECTOR

34-PIN CONNECTOR

42-PIN CONNECTOR

Push.

RETAINING TAB

Slide.

Push.

Push.

COVER

VEHICLE CONNECTORS

10 of 13 AII 44625

38. Insert the white and pink switch harness terminals into the appropriate cavities of the white vehicle 34-pin connector.

39. Secure the switch harness to the vehicle harness with electrical tape.

40. Reinstall the connector cover, and reconnect the vehicle connectors.

41. Secure the switch harness to the vehicle harness using two wire ties.

931203AG

SWITCH HARNESS

VEHICLE HARNESS

SWITCH HARNESS

ELECTRICAL TAPE

WHITE WIRE TERMINAL

PINK WIRE TERMINAL

VEHICLE 34-PIN CONNECTOR(white.)

HARNESS SIDE VIEW

WHITE WIRE TERMINAL

PINK WIRE TERMINAL

931204AG

SWITCH HARNESS

WIRE TIE

VEHICLE HARNESS

FUSE BOX


42. Turn the steering wheel 90° counterclockwise, and unplug the vehicle connector from the light/turn signal switch.

43. Remove the two self-tapping screws from the light/turn signal switch. While pushing the retaining tab, slide the light/turn signal switch, and remove it from the steering column. Do not pull on the light/turn signal switch lever.

6303180B

VEHICLE CONNECTOR

STEERING WHEEL

VEHICLE CONNECTOR



HOLDER

7109010E

RETAINING TAB

SELF-TAPPING SCREW

STEERING COLUMN

LEVER

CASE

TAB HOLE



44. Install the new light/turn signal switch in the steering column with two self-tapping screws. Do not hold the light switch by the lever.

45. Plug the vehicle connector into the new light/turn signal switch.

7109020E

STEERING COLUMN

SELF-TAPPING SCREW

LEVER

CASE

RETAINING TAB

TAB HOLE

NEW LIGHT/TURN SIGNAL SWITCH

6303210B


VEHICLE CONNECTOR

VEHICLE CONNECTOR


HOLDER

(1008) 11 of 13

46. If the 20A fuse is already installed in the fuse box, go to step 47, otherwise install the 20A fuse in the fuse box.

47. Check that all wire harnesses are routed properly and all connectors are plugged in.

48. Reinstall all removed parts. Do not reinstall the bumper clip and bolts that fasten the bumper at this time. Check that all clips and fasteners are installed securely.

49. Reconnect the negative cable to the battery.

50. Reset the clock, and reset the XM radio presets (if equipped).

6303220B

FUSE BOX

FUSE BOX

20A FUSEVIEWED FROM FRONT

PLUGGING POINT

12 of 13 AII 44625

Fog Light Aiming Adjustment

51. Aim the fog light:

• Pull down the inner fender and under cover.

• Adjust the aim according to local laws and regulations.

• To adjust, turn the aiming adjustment knob in or out until the correct aim is obtained.

52. Reinstall the bumper clips and bolts.

USE AND CARE

How to Operate the Fog Lights

• Turn the light switch to the “ ” position (headlights on low beam).

• Turn the fog light switch on (indicator is on).

• If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable.

NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.

922503AG

FOG LIGHT

To lower.

To raise.

AIMING ADJUSTMENT KNOB

FO

G L

IGH

T

SW

ITC

H

HEADLIGHT SWITCH

Low HighOFF

ON

OFF - - - -

- - -ON

AUTO/


BULB REPLACEMENT

1. Remove one bolt and one clip, and pull down the under cover and inner fender.

2. Unplug the connector from the fog light.

3. Remove the bulb.

922504AG CLIP BOLT

FRONT BUMPER

922505AG

LEFT FOG LIGHT

BULB

CONNECTOR


4. Install the new bulb and socket into the fog light. Use only a Genuine Honda halogen light bulb of the specified wattage.

Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003.

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.

• Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers.

5. Reinstall the removed parts in the reverse order of removal.

• Check that the wire harnesses are not pinched.

• Be sure to tighten the clip and bolts securely.

6. Check the operation of the fog light; adjust the aim if necessary.

922506AG NEW BULB FOG LIGHT

CONNECTOR

Turn.

NEW BULB

(1008) 13 of 13

Documents

INSTALLATION FOG LIGHTS 2011 CR-V INSTRUCTIONS AUG 2010 · Illustration of the Fog Lights on the Vehicle INSTALLATION 1. Make sure you have the anti-theft code for the audio and navigation