Part Number: JEE-201-05 012405-2 INSTALLATION INSTRUCTIONS JEEP GRAND CHEROKEE (2005-2007) NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Begin installation by using the Dash Trim Tool (Part #SIT-104) to release the trim ring around shifter. There are six clips that secure this trim ring to the shifter bezel. Note: Be carefull when removing this trim ring as it is very fragile. Set trim ring aside in a safe place. Continue with the Dash Trim Tool removing the bezel that surrounds the shifter. Set this bezel aside in a safe place. Use the Dash Trim Tool to remove the bezel that surrounds the radio. This bezel has two clips on the top, two on each side of the air vents, and one on the bottom directly under the radio. Remove the bezel and set aside carefully. Use the Dash Trim Tool to release six clips from the main dash bezel that has the climate control integrated into it. When released, pull gently to gain access to the lower right screw that secures the radio. Remove this screw with a #2 Phillips screwdriver and set screw aside in a safe place. Place Custom bezel Mount over existing screw hole, replace fac- tory screw, and tighten. Reinstall the dash trim bezel in reverse order. Install any Bracketron phone holder or Amps compatible device to your Custom Bezel Mount. Your installation is complete. Logo and part number will be right side up and readable when installed. TOOLS NEEDED: Dash Trim Tool (Part #SIT-104), #2 Phillips screwdriver. PARTS INCLUDED: One CBM and instructions. LOCATION OF MOUNT: To the right of the climate control Step 1. Step 2. Step 3. Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: Ph: 651-952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443 Web Address: www.bracketron.com Always check our website for the most updated model year compatibility information. Six (6) Plastic Clips © Bracketron Inc, 2007 All rights reserved. The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information. Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.

INSTALLATION INSTRUCTIONS...Part Number: JEE-201-05 012405-2 INSTALLATION INSTRUCTIONS JEEP GRAND CHEROKEE (2005-2007) NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON

Download PDF Report

Upload
others
View
7
Download
0

Embed Size (px)

Citation preview

Part Number: JEE-201-05

012405-2

INSTALLATION INSTRUCTIONS

JEEP GRAND CHEROKEE (2005-2007)

NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.

Begin installation by using the Dash Trim Tool (Part #SIT-104) to release the trim ring around shifter. There are six clips that secure this trim ring to the shifter bezel. Note: Be carefull when removing this trim ring as it is very fragile. Set trim ring aside in a safe place. Continue with the Dash Trim Tool removing the bezel that sur-rounds the shifter. Set this bezel aside in a safe place.

Use the Dash Trim Tool to remove the bezel that surrounds the radio. This bezel has two clips on the top, two on each side of the air vents, and one on the bottom directly under the radio. Remove the bezel and set aside carefully. Use the Dash Trim Tool to release six clips from the main dash bezel that has the climate control integrated into it. When released, pull gently to gain access to the lower right screw that secures the radio. Remove this screw with a #2 Phillips screwdriver and set screw aside in a safe place.

Place Custom bezel Mount over existing screw hole, replace fac-tory screw, and tighten. Reinstall the dash trim bezel in reverse order. Install any Bracketron phone holder or Amps compatible device to your Custom Bezel Mount.

Your installation is complete.

Logo and part number will be right side up and readable when installed.

TOOLS NEEDED: Dash Trim Tool (Part #SIT-104), #2 Phillips screwdriver.PARTS INCLUDED: One CBM and instructions.LOCATION OF MOUNT: To the right of the climate control

Step 1.

Step 2.

Step 3.

Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: Ph: 651-952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443Web Address: www.bracketron.com

Alw

ays

chec

k ou

r web

site

for t

he m

ost u

pdat

ed m

odel

yea

r com

patib

ility

info

rmat

ion.

Six (6) Plastic Clips

© Bracketron Inc, 2007 All rights reserved.The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount.Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.