Installation Instructions X Position head rail at an angle

Installation Instructions

Honeycomb Shades Continuous Cordloop

Getting Started

Remove shade from package. Save packaging until shade is installed and working to your satisfaction. Tools: � Power drill � Tape measure � Screwdriver � Level � Pencil Installation Screws

Surface Fastener #8 1 1/4” Screws (Provided) M3.8x51mm screws

Wood

#6 3/4” screws

Drywall/Plaster Wall Anchors, Expansion Bolts (Not Provide)

Metal Sheet Metal Screws (Not Provide)

Check Component/Hardware:

Installation Bracket

Hardware Standard Quantity

Order Width (X) X≦39" 39"＜X≦66"

66"＜X≦93"

93"＜X≦120"

Installation Bracket 2 3 4 5 1 1/4" Screw for

Installation Bracket 4 6 8 10

M3.8x51mm screw for Tensioner 2 2 2 2

Spacer Block(Optional) 1pc for extend distance 10mm 2pcs for extend distance 18mm

2" Screw for Installation Bracket with spacer

block(Optional) 4 6 8 10

Hold Down Bracket (Optional)

2 2 2 2

3/4" Screw for Hold Down Bracket (Optional)

4 4 4 4

Step 1: Bracket Installation

Measure 3” from both ends of the head rail. Mark bracket location on the mounting surface.

Inside Mount � Allocate a min. distance of 1/16’’ from wall to the front of brackets as below drawing.

� Use two #8 1 1/4 ” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.

Outside Mount � Allocate a min. distance of 5/8’’ from wall to the bottom of brackets as below drawing.

� Use two #8 1 1/4 ”mounting screws to attach each bracket. Use wall anchors for drywall or plaster wall.

Step 2: Shade Installation

� Position head rail at an angle so that it is hooked to the front of the bracket. Then push it upward to snap into the bracket.

For proper installation, start with attaching the front rail to the bracket.

Step 3: Cord Tensioner Installation

� Make sure the cord is tightened / taut without stretching, twisting or crossing, and the tensioner and control cord does not interfere with raising or lowering the shade before cord tensioner is mounted. � But for Cordloop SmartRelease only, the control cord cannot be too tightened / taut when installing due to its own system character.

� Use 2pcs M3.8x51mm screws to mount the cord � tensioner to the wall or window frame firmly for both inside & outside mount. Please refer to the following steps:

Step 1 Step 2

Step 3

Step 4: How to Install Hold Down Brackets (optional)

� Use #6 3/4” screw to secure each bracket.

3” 3” Space Evenly

1111 ��

Hold Down Bracket

(Optional)

Step 5: Shade Operation � For Cordloop, Pull cord to operate shade. Cord Tensioner must be fully tightened prior to operating the shade.

For Cordloop SmartRelease, Cord Tensioner must be fully tightened prior to operating the shade. Pull the front control cord to let the shade go up.

Pull the back control cord, the shade will go down automatically, till it fully close. If want to stop the shade go down, only need to pull the front control cord a little.

Note: the control cord cannot be too tightened / taut when installing due to its own system character. There should be no obstruction when the shade going down. Please do not play the bottom rail and control cord which may harm the shade.

Remove the Shade � Fully raise the shade. � Gently pry the bracket off the head rail with a flat screwdriver. � Remove the shade.

Note

� Keep away from heat, sparks and open flame. � Larger windows may require two people to install. � Proper In the process of installation, must support the shade firmly to avoid it fall down too quick to damage the people or itself. � Operate shade only by pulling the cord. � To ensure child safety, install cord cleat and tighten up any loose cords after the shade is installed

Cleaning

Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).

��

N300476 65101-11728

Installation Instructions Honeycomb Shades

SmartFitTM

3/8” Single 3/8”Double & 3/4”Single with Rail Cover

Getting Started

Remove the shade from the package. Save the packaging until the shade is installed and working to your satisfaction. Tools Needed： Power drill and drill bit

Measuring tape Screwdriver Level Pencil

You will need to use the following fasteners for your particular mounting surface.

Surface Fastener

Wood M3.5×25mm Screws (Provided) M3.8×38mm

Drywall/Plaster Wall Anchors, Expansion Bolts (Not Provided)

Metal Sheet Metal Screws (Not Provided)

Hardware Order Width (X) X≦50" X>50"

Handle 2 4 Cord Equalizer Housing Base

(for 3/8” Single) 4 7

Cord Equalizer Housing Base(for 3/4”Single & 3/8”Double) 2

L Bracket (for 3/8”S, Wall Mount) 4 7 L Bracket for windows with marble sill (Optional) (for 3/8”S) 2 2

L bracket (for 3/4”Single & 3/8”Doubld, Wall Mount)

8.5”<X≦ 40”, 2 40”<X≦ 52”, 3

52”<X72”, 4

M3.5×25mm Screw (for Base, 3/8” S, Inside Mount) 4

M3.5×25mm Screw (for Base, 3/4”S & 3/8”D, Inside Mount)

8.5”<X≦40”, 4 40”<X≦52”, 5 52”<X72”, 6

M3.8x38mm screw (for Wall Mount) L bracket qty*2

M3 x 3.6mm Bolt (for locking base on L bracket, Wall Mount) 2

Spacer Block (Optional, Wall Mount)

1pc to extend distance 10mm

2pcs to extend distance 18mm

Bracket Installation Inside Mount – for 3/8”Single Cell For flush mount, the minimum distance from the top/bottom wall to the base side is 1/4” and 1/8” from the side wall to the edge of Base. Use M3.5×25mm Screw to secure the base. Align the cover with the notch of the base and push the cover in toward the wall.

Inside Mount – for 3/8” Double Cell & 3/4”Single Cell For flush mount TOP, the minimum distance from the left/right side wall to the end of rail cover is 1/8” and the distance from the center of screw hole to edge of wall is A (A=1 1/16” for 3/8”D & A=1 1/4” for 3/4”S). Use M3.5×25mm Screw to secure the rail cover. Align the cover with the notch of the base and push the cover in toward the wall.

For flush mount BOTTOM, the minimum distance from the bottom wall to the base side is 1/8” and the distance from the edge of wall to the center of the screw hole is A (A=11/16” for 3/8”D & A=7/8” for 3/4”S). Use M3.5×25mm Screw to secure the base.

Align the cover with the notch of the base and push the cover in toward the wall.

Side mount L bracket for windows with marble sill (optional for 3/8”Single) Allocate a distance of 1/4” from bottom corner window frame and use two M3.8×38mm screws to secure the L bracket. Use one M3 x 3.6mm bolt to attach base to the L bracket (through inner screw hole)

(Top View) Outside Mount – for 3/8”Single Cell Allocate a minimum distance of 3/8” from top window opening to the L bracket and align L bracket 1/16” away from shade end. Use two M3.8x38mm screws to fasten the L bracket. Once the L bracket is installed, use one M3 x 3.6mm bolt to attach base. Finally, align the cover with the notch of the base and push the cover in, as shown in “Inside Mount” illustration. (Top)

5/8'

'

5/16''

(Bottom) Install the bracket similar to top steps but in reverse way. Outside Mount – for 3/8”Double Cell & 3/4”Single Cell Allocate a minimum distance of 5/8” from the center of screw hole to the edge of the wall and align the center of screw hole 1” away from the wall as the following picture. Use two M3.8x38mm screws to fasten the L bracket. Finally, align the cover with the notch of the base and

push the cover in, as shown in “Inside Mount” illustration.

(Bottom) Install the bracket similar to previous step but in reverse. Use one M3 x 3.6mm bolt to attach base.

Handle Installation Slide the handle onto the plastic piece pre-attached to the rails.

Notes For child safety, please check and ensure that there are no loose cords after the shade is completely installed. Please also make sure that cords are nice and tight and not tangled.

Cleaning Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).

Step1 Step 2

(Bottom View)

(Top)

1/4”

step1

step3

step 2

notch

1/8”

Base

Cover

Cord Equalizer Housing Base

Cord Equalizer Housing Cover

End cap

Head rail

Blanket

Bottom rail

N300473-A65101-11725-B

Installation InstructionsHoneycomb Shades

Corded / Corded TDBU / Corded Day & Night

Getting Started


Remove shade from package. Save packaging until shade is installed and working to your satisfaction.


Tools Needed:Power drill and drill bitMeasuring tapeScrewdriver LevelPencil


Installation BracketHold Down Bracket

(Optional)

2" Screw for InstallationBracket with spacer1 1/4" Screw for 3/8”SInstallation Bracket1 1/4" Screw for 3/4”S &3/8”DInstallation Bracket3/4" Screw for Hold DownBracket/ Cord Cleat

2

2

3

2

4

2

2

4

2

4

3

6

3

6

4

8

4

8

Cord Cleat 1pc for Corded, 2pcs forCorded TDBU & Day & Night

Hold Down Bracket qty*2 +Cord Cleat qty

Spacer Block (Optional)

Order Width (X) 8 ½"≦X≦42 42"＜X≦75" X＞75"

Measure 3” from both ends of the head rail. Mark the bracket location on the mounting surfaceProper alignment of brackets will make installation easier.

Step 1: Bracket InstallationPosition the shade so that the front is facing you.Insert the rail with an angle facing the window; hooking up with the bracket front side, and then push it upward to snap into the bracket.


Install the cord cleat on the wall. Wrap the operating cords around the cord cleat for child safety. Always use the cord cleat to keep cords out of the reach of children. The cleat should be installed more than 64” (1.6m) from the door.

Step 5: Cord Cleat

Use two 3/4” screws to secure each hold down bracket.


For Corded: operate as below illustration, according to the location of cord lock.

For Corded TDBU & Day & Night: when lowering the shade, lower the bottom rail first and then middle rail.When raising the shade, raise the middle rail first and then bottom rail.

Step 4: Shade Operation

Cord Cleat Hold Down bracket (optional)

Installation Bracket(for 3/4” S(left) & 3/8”D(right))

Installation Bracket(for 3/8” S)

3'' Space Evenly Space Evenly 3''

Installation Brackets

for 3/8” Double cell & 3/4” Single cella.

for 3/8” Single cellb.

Allocate a min. distance of 3/16’’ from wall to the front of brackets.Use two 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.(Align the front of brackets flush with wall if only lock the back hole in the brackets.)

[ Inside Mount ]

Allocate a min. distance of 5/16’’ from the end of brackets to the top window frame. Use two 1 1/4’’ mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.

[ Outside Mount ]

Allocate a min. distance of 5/16” from the edge of the wall to the front of brackets. Use one 1 1/4” mounting screws to secure brackets.

[ Inside Mount ]

Allocate a minimum distance of 3/16” from the end of brackets to the top window frame. Use one 1 1/4” mounting screws to attach each bracket.

[ Outside Mount ]

5/16”

3/16"


1

2 2

1

Lower

Raise

Unlock Lock

64"

(1.6

m)

Floor

Young children can STRANGLE in cord and bead chain loops. They can also wrap cords around their necks and STRANGLE.

Always keep cords out of children's reach.Move cribs, playpens, and other furniture away from cords and bead chains. Children can climb furniture to get to cords.Always wrap the cords around the cleats in a figure eight, up high, out of reach of children.

WARNING3/16''

5/16''

Note: for 3/8”D & 3/4”S shade, Optional flat head screws included. Use as needed.

Fastener1 1/4” Screws (Provide)

for 3/8”S

for 3/8”D & 3/4”S

3/4” Screws(Provide)

Wall Anchors, Expansion Bolts(Not Provided)

Sheet Metal Screws(Not Provided)

Wood

Drywall/Plaster

Metal

Surface

Un jeune enfant peut s'ÉTRANGLER avec la boucle d'un cordon ou d'une chanette. Il peut aussi enrouler le cordon autour de son cou et

s'ÉTRANGLER.Gardez toujours les cordons hors de portée des enfants.

Éloignez les lits et parcs de bébé, ainsi que toute autre pièce de mobilier, des cordons et des chaînettes. Un enfant peut grimper sur un meuble pour atteindre les cordons.

Enroulez toujours les cordons en noeud en huit autour du taquet de cordon, placé haut et hors de portée des enfants.

MISE EN GARDE

For Corded, Fully raise the shade For Corded TDBU & Day & Night, Lower the mid rail Insert screwdriver into the gap between the back of the rail and the bracket. Gently maneuver the screwdriver toward yourself to pry the bracket.

Remove the Shade

Safety WarningWarning! Children can become entangled and strangle in window shade cords. Keep all cords out of reach from children. Move cribs and other furniture away from window coverings with cords.The following devices are recommended: Cord cleat (included) Clip/Clamp Tie the cord to itself Use any tie-down device

CleaningRoutine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).

Our Shade comes equipped with an Ellipse Safety Cord Connector that prevents child strangulation. If the device comes apart, please refer to below steps:1. Open the Ellipse Safety Cord Connector entirely. 2. Align all cords and slide them into the slot of Ellipse Safety Cord Connector (the slot should be the side in round circle); 3. Close the Ellipse Safety Cord Connector; 4. Pull the tassel cords and make sure it is closed tightly.Note: the transparent bead should be exposed at the top of Ellipse Safety Cord Connector.

How to Reassemble Ellipse Safety Cord Connector

Young children can bee n t a n g l e d a n d s t r ang led i n co rds . Keep all cords out of children’s reach. Cord cleat is provided and should be used.

! WARNING

Troubleshooting

Problem Solution

For corded TDBU & Day & Night, if the

bottom shade fabric not remain stacked

(billowed on the windowsill), when the

top was lowered

When lower the bottom shade, please pull the left side cord leftwards to lock the bottom rail. Please make sure the bottom rail is locked

right above the windowsill first (if not

locked, please try more times) before operating

the top shade.

Inner cord stop devices can reducethis risk if positioned correctly on the operating cords.

If inner cord stop devices are more than 3" (76 mm) below the headrail when the blind is fully lowered, move them closer by following the inner cord stop device adjustment instructions.

Inner cords can pull out to form a loop, which can strangle a young child.

3" or less

Las cuerdas internas pueden sacarsepara formar un lazo en que puedeESTRANGULARSE un niño pequeño.

Los dispositivos de paro de la cuerda interna pueden diminuir este riesgo si están situados correctamente en el halado de las cuerdas. Si los dispositivos de paro de cuerda interna son más de 3 pulgadas(76 mm) por debajo del riel superior cuando está bajada ompletamente la persiana, muévalos siguiendo las instrucciones del ajuste de paro de cuerda interna.

ADVERTENCIA3" o menos

Les cordons intérieurs peuvent sortir pour former une boucle et ÉTRANGLER un jeune enfant.

Les dispositifs d’arrêt des cordons intérieurs peuvent diminuer ce risque s’ils sont placés correctement sur les cordons.Si les dispositifs d’arrêt des cordons sont situés à plus de 76 mm (3 po) en store est complètement baissé, rapprochez-les en suivant les instructions de réglage du dispositif d’arrêt du cordon intérieur.

MISE EN GARDE76mm (3 po)o menos

N300474-A65101-11726

Installation InstructionsHoneycomb Shades

Cordless & Cordless TDBU & Cordless Day&Night


Getting StartedRemove shade from package. Save packaging until shade is installed and working to your satisfaction.


Tools Needed:LevelMeasuring TapePencilPower drill(¼” hex driver and drill bit)Screwdriver



Hold Down Bracket(Optional)

1 1/4" Screw forInstallation Bracket2" Screw for InstallationBracket with spacer3/4" Screw for Hold

Down Bracket

2 3 54

2 2 22

4

4

4

6

6

4

8

8

4

10

10

4

Handle

1pcs for X≦50", 2pcs for X>50"(Cordless)

2pcs for X≦50", 4pcs for X>50"(Cordless TDBU & Day & Night)

1pc for extend distance 10mm2pcs for extend distance 18mmSpacer (Optional)

Order Width (X) X≦39" 39"<X≦66" 66"<X≦93" 93"<X≦120"

Measure 3” from both ends of the head rail. Mark the bracket location on the mounting surface

Step 1: Bracket Installation

Position head rail at an angle so that it is hooked to the front of the bracket. Then push it upward to snap into the bracket.


Slide the handle onto the plastic piece pre-attached to the rails.

Step 3: How to Install Shade Handle

For corded, fully raise the shade.For TDBU & Day & Night, Lower the middle rail.Gently pry the bracket off the head rail with a flat screwdriver as below picture.

Remove the Shade

Routine cleaning will help maintain the beauty of your shade. The shade can be cleaned by using a soft brush, vacuumed with a low suction hand-held vacuum, cleaned ultrasonically (specify that a mild solution must be used and that the head rail should never be immersed in liquid), or dampen a clean cloth with a warm water and mild detergent solution to dab the spot until it’s gone (do not rub!).

Cleaning the Shade

To lower the shade, gently pull down the shade on the bottom rail handle and stop at the desired location.For TDBU & Day & Night, pull down the bottom rail first before lowering the midle rail.

To raise the shade, gently raise the shade on the bottom rail handle to desired height.For TDBU & Day & Night, if the shade will not lift, pull the midrail down fully to the bottom first and then raise the bottom rail together with midrail up.

Step 4: Shade Operation

Use #6 3/4” screw to secure each bracket.


Fastener#8 1 1/4” Screws(Provide)

#6 3/4” Screws

Wall Anchors, Expansion Bolts(Not Provided)

Sheet Metal Screws(Not Provided)

Wood

Drywall/Plaster

Metal

Surface

Hold Down bracket(optional)



3'' 3''Space Evenly Space Evenly

[ Inside Mount ]For Cordless, align wall to the front of brackets. For Cordless TDBU & Day & Night, allocate a min. distance of 1/16” from wall to the front of brackets.Use two #8 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.

[ Outside Mount ]Align the end of brackets with the top window frame.Use two #8 1 1/4” mounting screws to secure brackets. Use wall anchors for drywall or plaster wall.

Do not grasp the rail unevenly. Always lower or raise the shade in the middle or use both hands with even pressure to two handles of the rail.

1/21/2

1/31/3

1/3

Remove the shade

Troubleshooting

SolutionProblemThe shade will

not snap into themounting brackets

Check if mounting bracketsare aligned. Refer to Step 1.

Lower the shadecompletely, then raise it up

to correct it.Repeat if necessary.

The shade will not lift

The shade stack upunevenly

Gently pull down on the bottom rail to reactivate the

cordless mechanism. Repeat if necessary.

For TDBU & Day&Night, pull the midrail down fully to the bottom first and then raise

the bottom rail together with midrail up.

Handle

Hold Down Bracket

Bottom rail

Blanket

Middle rail

Head railBracket

(Cordless) (Cordless TDBU / Day & Night)

(Cordless) (Cordless TDBU / Day & Night)

1/16''

Note: Optional flat head screws included.Use as needed.

Lynn.Lee

文字方塊

N300474-A 65101-11726-A

Documents

Installation Instructions X Position head rail at an angle