Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
InstallationInstructions
Self Cleaning RadiantElectric Slide-In Range
JSP46, JSP56, JS966
"If you have questions, Call 800-GE-CARES orvisit ourwebsite at:www.GEAppliances.com"
Skill Level: High Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installationis not covered under the GE Appliance Warranty. See the Owners Manual for warrantyinformation.
CAUTION: Before you beginRead these instructions carefully andcompletely.• IMPORTANT- Save these instructions for
local inspector's use.
• IMPORTANT- Observe all governing codesand ordinances.
• NOTE TO INSTALLER- Be sure to leavethese instructions with the consumer.
• OWNER- Keep these instructions for futurereference.
• WARNING- This appliance must beproperly grounded, See "ElectricalRequirements" page 2.
Parts Included
2 Screws _
__ Screws
Anti-Tip Bracket__
Tools You Will Need
/1/4"N utdriver
Wrench or Pliers
(for 1 7/16" nut)
Level
Materials Needed
6Lag Bolts Anchor
Sleeves(For Concrete FloorsOnly)
( UL Approved 50 AMP)
4- Wire Cord OR 3 -Wire Cord
4'long 4'long
Drill with1/8" Bit
Pencil
Tape Measure
Straight Edgeor Square
SafetyGlasses
Hand orSaberSaw
Pliers
Pub. No. 31-10426
22gc4053P412 1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
,_ WARNING: For personal safetyremove house fuse or open circuitbreaker before beginning
installation. Failure to do so could result in
serious injury or even death.
All rough-in and spacing dimensions must be metfor safe use of your range. Electricity to the rangecan be disconnected at the outlet without movingthe range if the outlet is in the preferred location(remove lower drawer).
To reduce the risk of burns or fire when reachingover hot surface elements, cabinet storage spaceabove the cooktop should be avoided. If cabinetstorage space is to be provided above thecooktop, the risk can be reduced by installing arange hood that sticks out at least 5" beyond thefront of the cabinets. Cabinets installed above a
cooktop must be no deeper than 13".
Be sure your appliance is properly installed andgrounded by a qualified technician.
_1_ WARNING: To reduce the risk oftipping, the appliance must be
secured by properly installing theanti-tip bracket packed with the appliance.
See Installation Instructions
If you pull the range out and away from the wallfor any reason, make sure the Anti-Tip bracketis engaged when the range is pushed backagainst the wall.
Electrical RequirementsThis appliance must be supplied with the propervoltage and frequency, and connected to anindividual properly grounded branch circuit,protected by a circuit breaker or fuse havingamperage as specified on the rating plate. Therating plate is located above the storage draweron the oven frame.
We recommend you have the electrical wiringand hookup of your range connected by aqualified electrician. After installation, have theelectrician show you where your main rangedisconnect is located.
Check with your local utilities for electrical codeswhich apply in your area. Failure to wire youroven according to governing codes could result ina hazardous condition. If there are no local
codes, your range must be wired and fused tomeet the requirements of the National ElectricalCode, ANSI/NFPA No. 70-Latest Edition. You canget a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269Effective January 1, 1996, the National ElectricalCode requires that new, but not existing,construction utilize a 4 conductor connection to
an electric range. When installing an electricrange in new construction, follow the instructionsin the section on NEW CONSTRUCTION ANDFOUR CONDUCTOR BRANCH CIRCUITCONNECTION.
You must use a three-wire, single-phase A.C.208Y/120 Volt or 240/120 Volt, 60 hertz electricalsystem. If you connect to aluminum wiring,properly installed connectors approved for usewith aluminum wiring must be used.
2
Installation InstructionsPre- Installation Checklist
D Inspect Installation Location
[]
[]
Inspect cutout dimensions and locationof receptacle to be sure it fits withinlayout Iocation.(See page 5.)
Refer to alternate construction section for
the following non standard installations.a. Counter opening extends to the wall:
Maintop Filler (supplied with the range.)(See Page 12 section AA for InstallationInstructions) or
Backguard (Kit JXS36XX or JXS39SS).See page 12.
b. Counter height greater than 36 3/4":Lower Trim Slide-In (Kit JXS56XX).
¢. One side is not enclosed by a cabinet:Bodyside (Kit JXS76XX).
d. Island Installation:
To provide an optimum installation, thetop surface of the counter top must belevel and flat (lie on the same plane)around the 3 sides that are adjacent torange cooktop. Proper adjustments tomake the top flat should be made orgaps between the countertop and rangecook top may occur. Forcing the cooktop to fit may cause excessive gaps andcould break glass and void warranty.
To Procure Kits:
a. Visit GE Web Site, see page 1.b. Call GE Answer Center, see page 1.c. Contact Dealer
D
[]
[]
[]
Move Range Indoors In frontof Cabinet Opening(Do not use hand trucks when moving theunpackaged range.)
Protect the kitchen floor! Flatten and
place a piece of the shipping carton in frontof the installation location to protect theflooring.
Do not remove the protective channelfrom the sides of the glass cooktop, ifapplicable, until later in installation,
FrotectiveChannet
Carefully, tilt the range to access the rangeleveling legs. Use an adjustable wrench toscrew leveling legs out so that glasssupport flanges clear top of counter top.
3
Installation InstructionsPre- Installation Checklist
D Open oven door and remove literaturepack, broiler pan and grid, and ovenracks.
D
Open door to the Broil Stop position.
Grasp door on both sides, and lift upand off hinges.
Remove packaging materials on door,plastic on trims and panel, and all tapearound the range.
Storage Drawer Removal
D Pull the drawer out until it stops.
D Lift the front of the drawer until thestops clear the guides.
RAIL
GUIDE
STOP
D Pull foward and remove the Drawer.
4
Installation Instructions_-] Pre-Installation Cutout and Required
Clearances
If cabinets are placed less than 30" above therange, see alternate construction page 12.
NOTE: Product meets UL requirements for 0"clearance to back and side walls.
Wall coverings, counters and cabinets aroundrange must withstand heat (up to 200°F)generated by the range.
Follow instructionspackaged with alternateappliance.
F 6" Minrom Wal
For OptimumInstallation TheseSurfaces MustBe Flat & Level
35-1/2" to 36-1/2"from floor tocountertop
Max, depth ofcord, plug andrecpt, box
4" to preventinterferencewith drawer
AcceptableElectrical
Outlet Area
30" Min.from
COOkingsurface to
I_-'13 15" Min. verticaldistance fromthebottom of the adjacentoverheadcabinets
Countertop
Shave Raised EdgeTo Clear 31-1/8"Wide Control Panel
5
Installation Instructions
_-_ Standard Installation
Standard Installation
9/16" Min.Flat "--_
'T1/4" Min,Flat
23-3/16"
Wall---_
l25"Typically
9/16" Min.
_-_ 29 -15/16 to 30 -1/16" -"--_1Smooth Cut
FLAT AREA
t/4"-m_ I_
36"
If the construction of your cabinet cannotprovide a 1/4" flat area back of the countertopopening, consider changing the counter top toaccomodate this dimension. See alternateconstructions section. If the area is not flat,excess tension may be applied to the glasscausing breakage and voiding the warranty.
r._ Be careful not to damage the adjacentcabinets while cutting the countertop.Use a hand or saber saw to make
straight smooth cuts.
[_ Remove countertop raised edge. Ifincorporated (See illustration on page 5).
% Center the 30" wide opening over theadjacent cabinets and mark with astraight edge.
Using a straight edge mark the back lineat 23-3/16" from the front edge of thecounter.
6
Installation InstructionsElectrical Connections
['_ Remove wire cover atlower rear of range.
When using a power cord, remove theknockout in the connection plate withpliers as required by the size of thestrain relief or clamp supplied with cord.
TermHousing
Insert power cord through hole in theterminal housing, engage and tightenstrain relief clamp, leaving enough wirelength to attach terminals to terminalblock.
StrainRelief
Clamp
_-_ FOLLOW INSTRUCTIONS BELOW IFYOUR CORD IS 3 WIRE.
The power cord center wire must,oAmp,w,ro be connected to middle terminal
_ on block. Attach remaining wiressecurely. Do not remove groundstrap
3 wire
Black Connection
White PlateRed
Relnove
3 SCrew sStrainRelief
Clamp
ORNEW CONSTRUCTION AND FOUR
CONDUCTOR BRANCH CIRCUIT
50 Amp 4 Wire
[] Follow instructionsbelow if your cord is 4wire.
Remove the screws onthe terminal block. Donot remove terminalblock.
Remove the
green groundscrew. Thenremove the
ground strap anddiscard it.
REMOVE & DISCARD
GROUNO STRAp
Terminal Block
Attach the green or bare wire below theterminal block with the green groundscrew and washer that were removedearlier.
_] Connect the red and black wires to theoutside terminals. The white wire must beconnected to the center terminal.
GroundedNeutral
Black
Ground Screw& Washer
Ground
Wire(white)
Clamp
['_ Re-install the wire cover making surethe wires do not become pinchedbetween wire cover and housing.
7
Installation InstructionsInstalling the Anti-Tip Bracket
_-_ Locating The Bracket
a. Decide whether the bracket will be
installed on the right or left side of rangeopening.
b. Place the bracket as shown in Fig. 1.
ADJACENT CABINET 3_"
/ WALL (_hih_FLOOR-WOOD /
BRACKETBIDE
REAR
LEGFLOOR-CONCRETE
Fig. l
Installing The Bracket in Woodor Concrete
INSTALLATION-WOOD CONSTRUCTION
a. Locate the centers of the four holes identified
in Fig. 1 as Floor-Wood and Wall.b. Drill a 1/8" pilot hole through the pre-marked
areas. Note the angle of the wall screw inFig. 2.
c. Mount the Anti-Tip bracket with the fourscrews provided.
ATTACHMENT TO WALL
TO FRONTEDGE
OF _ 25"_COUNTERTOP
BRACKET
SCREW MUST
WALLPLATE
OR METAL
Fig. 2
INSTALLATION-CONCRETE CONSTRUCTION
a. For concrete installation you will need two1/4"x 1-1/2" lag screws, and two sleeveanchors.
b. Locate the center of the four holes identified
in Fig. 1 as Floor-Concrete and Wall. Drillthe recommended size holes in each.
c. Install the sleeve anchors into the predrilledconcrete holes and install the lag and wallscrews through the Anti-Tip bracket. Makesure the screws are securely tightened.
8
Installation InstructionsInstalling the Range
SLIDE RANGE INTO OPENING
Position the range in front of thecabinet opening.
Make sure that the glass whichoverhangs the countertop clears thecountertop. Raise the unit by loweringthe leveling legs if necessary.
%%
Push while lifting the range into theopening until the range is within 2" ofengaging the anti-tip bracket
Remove the protective trim from theside of glass. (If provided)
_] Using the adjustable pliers or wrenchcarefully screw in the back leveling leguntil the glass overhang comes to reston the counter top.
JU o'a
% Carefully push the range into theopening until the counter top fullyengages the control panel. The back
glass overhang should cover the cutoutopening.
ountertop
Make sure the edgeof the countertop fits flush
againstthe end of theFrontControl Panel
F_ Plug range cord into receptacle. Locatethe cord in the back of the range in amanner that will not touch or be moved
by the drawer.
POSITIONRANGECORDSOTHATTHEREIS NOINTERFERENCEWITH
\\
f
\ //
\
\
[_ hen carefully screw in the front twoleveling legs (similar to E5) until the
glass overhang touches thecountertop.
9 Continued on following page
Installation InstructionsInstalling the Range <ooo .)
Final Check of the Anti-Tip Bracket
[_ When installation iscomplete and therange is in place,inspect to be surethe rear leveling legis fully inserted intothe slot of the Anti-
Tip Bracket.
CAUTION: The oven door is heavy.You may need help lifting the doorhigh enough to slide it down ontothe hinges. Do not lift the door bythe handle.
Replacing the Oven Door
Make sure the hinge is in the broilstop position.
Grasp the door on both sides.
Lift the door over the hinges lining upthe hinges with the hinge slots on thebottom of the door.
_ Slide the door down onto the hingesas far as it will go and close the door.
Replacing the Storage Drawer
_] Place thedrawer rail on
the guides.
_ Push thedrawer in until
it stops.Stop
[_ Lift the front of the drawer and push inuntil the stops clear the guides.
F_ Lower the front of the drawer andpush in until it closes.
SPECIAL INSTRUCTIONS IF YOUHAVE PROBLEMS WHILEREPLACING THE STORAGEDRAWER
IF DRAWER WON'T CLOSE
DRAW_F_ F_ONT PANE_
DRAWER I TIPPED AWAY FROM
............COMPleTELY _ I _ BODY 51DE _ I_
POWER CORD MAY B_ _AR ORAW_ SUPPORT IS
Remove and replace, making sure the powercord is not obstructing the drawer and/or therail is in the guide.
IF DRAWER IS CROOKEDREAR DRAWER SUPPORT IS DRAWER FRONT PANEL
Remove and replace making sure the rail is inthe guide.
10
Installation Instructions
Final Check List
Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced.
Be sure power is in service to the building.
Check to be sure that all packing materials and tape on metal panel (if applicable) undercontrol knobs and drawer have been removed.
Operation Check List
Check to make sure the Clock display is energized. If a series of horizontal red lines appear in
the display, disconnect power immediately. Recheck the range wiring connections. If change ismade to connections, retest again. If no change is required, have building wiring checked for
proper connections and voltage. It is recommended that the clock be changed if the red linesappear.
Push down and turn any one of the four surface knobs to "MED" setting to observe that theelement glows within 15 seconds. Turn the knob off when glow is detected. If the glow is not
detected within the time limit, recheck the range wiring connections. If change is required,retest again. If no change is required, have building wiring checked for proper connections and
voltage.
11
Alternate ConstructionInstallation Instruction Preparation
Optional Maintop Filler orBackguard KitIf counter opening extends to the wail, it will requireMaintop Filler Kit (supplied with the range) orBackguard Kit (JXS36XX or JXS39SS) to close thegap.Note: If the counter top is greater than 25" it wilI show agap between the backguard and wall or between fillerkit and the wall.If the countertop is less than 25" a gap wilI occurbetween the countertop front and the control panelends (See section E7).
If you are using the optional backguard kit,
_" _mm m
i w°. li 25'"
Mu°_B°-,4I_ _°"_"1
31-_/8"
I Must BeLevet
'_'-Must BeFi_t
Refer to the Backguard Kit instructions for Installationdetails,
If you use the filler kit, place the metai filler piecesupplied with the range to the back of the range asshown in the figure below. Start the 2 screws into theupper holes at the outside rear of the range above theiouvers, through the slots in the trim, holding the fillerpiece centered on the maintop frame and pushingupward to close the gap between the bottom of theglass and the filler trim.
When the trim is set in the proper position tighten the 2mounting screws. The top of the trim should be locatedbelow the top surface of the glass to prevent pots, pansand skillets from damaging the painted parts.
Refer to the Standard Installation of the Rangebeginning on page 3.
Cookt_
--Range
"_" MaintopFiller
_'_ _ ( 2 )#8 Screws
[-A-'B-] Countertops higher than 36 1/2"Flat& Level ....... _ _
If countertop height //w_th _o_kis between 36 1/2"and 38" a lower trimkit (JXS56XX) isrecommended,Refer to Kitinstructions forinstallation detaiis.
r-A--c-1For Non-Built-In Installation(End of Cabinet Location)When installing the range at the end of a cabinetsection which will expose the unfinished side of therange, use Body Side Kit (JXS76XX), Refer to kitinstructions for installation details.
[-A---_ Island Installation
Attach the anti-tip bracket per instructions in section Dmaking sure that the rear of the bracket is 25" from thefront of the countertop.Beware that the screws provided are long and may)enetrate through the back of the island cabinets. In
this event, use shorter screws (not provided) or thescrews provided should be used in the floor, (SeeSection D for Wood/Concrete Floor Installation). Do notuse Backguard Kit JXS36XX or JXS39SS.
For Cabinet OpeningsApproximately 30-3/8"If range is installed in cabinet opening approximately30-3/8" the Vertical Side Trim Kit (JXS86XX) should beused to cover gaps between range sides and cabinet.Refer to the kit instructions for installation details.
[-A-'_ Cabinets over the Range lessthan 30"If a 30" clearance between cooking surface andoverhead combustible material or metal cabinetscannot be maintained, protect the underside of thecabinets above the cooktop with not less than 1/4"insulating millboard covered with sheet metal not lessthan 0.0122" thick.
Pub. No. 31-1042612 229c4053P412