P a g e | 1

Installer Manual DO NOT GIVE TO HOME OWNER.

FOR PROFESSIONAL USE ONLY .

4G Mult icom LITE GSM/Cellular Intercom System

Note: For legal reasons, telephone technical support is for registered and

qualified product installers only. Home owners and end-users should contact

their installer for product technical support.

LTE Ready4G

Preferred!

www.BFTGateOpeners.com | (800) 878-7829 | Sales@BFTGateOpeners.com

P a g e | 2

Contents

Really Important things (site survey) …………….Pg 3 Overview of outside of product …………….Pg 4

Overview of Inside …………….Pg 5 Pedestal Installation …………….Pg 7

Wall mount installation …………….Pg 8 Power IN module …………….Pg 8

Cellular module in detail …………….Pg 9 Wiring relays …………….Pg 9

Keypad / Prox module in detail …………….Pg 10 Connecting slave devices …………….Pg 10

Inserting SIM …………….Pg 11 Powering up and LEDs …………….Pg 11

Installing the Programming APP …………….Pg 12 Begin Programming a New Install …………….Pg 13

Begin Programming Existing Install …………….Pg 12

Programming Check Reception …………….Pg 15

Add a Family …………….Pg 16 Edit a Family …………….Pg 17

Activate Auto Sync …………….Pg 18 Add visitor Access …………….Pg 18

A closer look at keypad codes …………….Pg 19 A closer look at Prox cards …………….Pg 20

A closer look at caller ID …………….Pg 21 Do not disturb …………….Pg 22

Access control …………….Pg 22 Auto Opening …………….Pg 23

Enquire residents info …………….Pg 24 Concierge / Help / Assistance Button …………….Pg 24

More settings …………….Pg 25 Volumes …………….Pg 25

Dialling times …………….Pg 26 Relay times …………….Pg 26

Information screen …………….Pg 27 Manager controls of gate/door …………….Pg 28

Complete list of parameters …………….Pg 29 Troubleshooting …………….Pg 32

P a g e | 3

Really Important things you Need to Know..

Please read this entire manual before installing this product.

To be installed by certified and qualified personnel / gate automation dealer only. Not

for DIY install!

Ensure there is good network signal at the gate/door of the install site BEFORE installing

this product. (2G/3G/4G Europe, 3G/4G Australia & USA)

Set up on a bench in workshop BEFORE going to site. Program the unit in the comfort of your work bench and call technical support should

you have questions.

This product requires a SIM. The SIM should be a voice and text plan.

Do not use a DATA only SIM. Ensure your SIM has VOLTE if you only have

4G service (HD Voice calling service is enabled).

Manufacturer warranty does NOT cover lighting / storm damage. In lightning prone areas, you

MUST fit external surge protection and lightning rod in order to maintain warranty on

this product. Evidence of surge protection will be requested

on generation of RGA numbers.

5

1 2

3 4

6

P a g e | 4

Now lets have a look around the product…

Hinged front door

Keypad for dialling

apartment / house

number

Speaker grill Call status LEDs

(for DDA hearing

impaired visitors)

Illuminated nameplate

holder or information

screen. Visit

www.bftaccess.com for

template

Security Screw Access

(Open top screws only)

Optional Prox badge

reader

Enter apartment number

or address, then press

to CALL

Enter apartment

number or address,

then press to CALL

Enter door

code then

press to enter

or open

OPTIONAL

prox reader

Antenna

Enter door

code then

press to enter

or open

Jones

Smith

Goldberg

Lopez

Obrien

Johnson

Cortez

Welcome

to Orlando

Heights

Enter APT

number

then press

# to CALL

Illuminated info or name window. Visit

www.bftaccess.com for template

Pedestal

style

Wall /

building

Style

Security

Screw

Access

Speaker

P a g e | 5

Overview of Inside…

Antenna Power conditioning &

Surge protection module

Keypad

module

Optional

Prox coil

Optional

Prox module Info / name

window

Cellular

Module

P a g e | 6

Push button

Antenna

Connection

Optional Prox

reader module

Optional

Prox Coil

Cable Entry

Hole

Mounting

Holes

GSM / Cellular

PCB Module

Name window

holder

Illumination

PCB for name

window

P a g e | 7

Pedestal Installation

!

!

3 Use minimum 16 gauge wire

from the 24v dc adaptor

provided to the terminals

shown.

1 IF NECESSARY,

remove 4 screws and

remove power

conditioning module

After fitting the box to the

gooseneck, re-fit the module

and connect a 14 gauge earth

wire to the earth terminal. 2

Earth Rod

(close as

possible)

Maintain manufacturer’s

warranty by adhering to the

guidelines shown. Use 110v

surge protected supply.

Surge protected 110v

4 24v dc PSU

16 gauge MIN

25 feet MAX

Call box

P a g e | 8

Wall Mount Installation

!

!

24vdc out - +

+ -

+ - Solar out

24vdc IN

500mA quick blow

output fuse

Earth Rod

24v DC

OUT 24v DC IN from PSU

To Earth Rod

Weatherproof

enclosure

Use 110V surge

protection to maintain

warranty Wall or Pillar

(side view)

Wall mount

call station

IMPORTANT

18 gauge MIN

10 feet MAX

Earth Rod

Connection

Optional Battery

Connection leads

3Ah 12v dc max 1A quick blow

input fuse

Power

Module

in

Detail…

P a g e | 9

Relay 2

Gate Position

Limit switch

(optional)

Exit Button To Call

Button

12v dc 100mA

(backlighting)

24v dc IN

(pre-wired)

Relay 1

CPU Status

Signal Status

Power

Cellular

Module in

Detail…

SIM holder Modem Status

Antenna

connection

N/C

COM

N/O

N/C

COM

N/O

Wiring

Relays Note: The manufacturer is

not responsible for wiring to

third party devices. Please

consult an experienced

security installer.

Electric Gates

Pedestrian

gates or door

Magnetic

lock

Exit button Separate lock Power

supply (not supplied)

Sta

rt

Com

mon

P a g e | 10

1 2 3 24v

OUT

IN

OUT

INOUT

IN

1 2 3 24v

OUT

IN

1 2 3 24v

1 2 3 24v

Slave IN connections

Slave IN

Slave OUT

Optional

PROX

module

Baud jumper (remove

for older intercoms)

Keypad

Module

Connecting

Slave

Devices

Keypad /

PROX

Modules

in

Detail…

1 2

Slave OUT connections

3

To next

device

Optional

Keypad

Optional

Prox reader

Optional Slave

Keypad

24v out

Optional Slave

Prox Reader

CAT5 (30ft max)

300ft if device powered

separately

To next

device

GND

P a g e | 11

Inserting the SIM card

Powering Up & LEDs

Perform a final check of wiring and ensure the antenna is connected before switching on the

power. Once the power is switched on, the power LED should illuminate.

WARNING Ensure power is OFF. Do not hot

insert or remove while power on.

45 chamfer OUT

Pads DOWN

Ensure SIM is activated.

Pre-pay SIM will need credit first.

At&T preferred. T-Mobile also

compatible in certain areas.

CPU

Flashing = standby

Constant ON/OFF = busy

SIGNAL STRENGTH

1 flash = poor (1 bar)

2 flashes = low (2 bars)

3 flashes = good (3 bars)

4 flashes = Strong (4 bars)

5 flashes = searching

POWER

MODEM

Flashing = standby

Constant ON/OFF = searching

Preferred!

P a g e | 12

Installing the Programmer APP for the first time Download the smartphone app to program this unit. Search for BFT MULTICOM 4G and look for

the icon below...

Accept and allow all

permissions (Android

version shown)

To register first time,

enter your name, email

and cell phone number.

After you send the

registration email, go

back to the app screen

& press SETTINGS

P a g e | 13

NOTE: Do not change

engineers or managers

codes on the APP unless

they have already been

changed in the intercom

Now you are ready to begin programming!

Program a NEW

or EXISTING Job

Site

Press SETTINGS to reveal the

screen shown. Choose to

create a NEW site or edit an

existing one. Then you can

begin programming.

ANDROID Press & HOLD

Iphone use the “i” symbol

P a g e | 14

Select or Create a new Job Site

App AND Intercom Update

Use to change either the manager or

engineer programming codes on BOTH

the intercom and the APP.

App ONLY update

Use to update the APP, typically

when another user has changed the

programming codes on the intercom

from another phone.

Note: This app sends

SMS programming

strings to the intercom

as shown and it should

reply with OK

message. On iphones,

due to restrictions by

Apple, you must

confirm the SMS as

shown. Android

devices will auto send

the SMS in the

background.

P a g e | 15

Programming Now that you have either entered a new client, or selected an existing client from the client list,

you are now ready to begin programming.

Step 1: Check Reception

Go to MORE>INFORMATION to reveal the screen shown.

Press the reception check button. On Android the app will

automatically send a SMS string (*20#) to the intercom.

On iphone, users will be taken to their SMS screen to

confirm before sending the string.

The intercom should reply with a signal level between 1 & 31.

1-12

Poor

13-20

Medium

21-31

Good

For good performance, signal level should be at least 13 or

better on 3G or 4G and 14 or better on 2G.

TIP: If signal is lower than recommended, then take IMMEDIATE

action. Change network if possible, or use an optional high gain

antenna. Check power cable is within recommended

specification. (Poor power cable can lower reception).

SMS message sent to intercom.

SMS reply to your phone.

Step 1B:Set APN (for VOLTE / 4G voice calling)

This feature may need to be set in order to make 4G voice calls with At&T or one of the At&T resellers. Check the APN of your provider and then enter it in the blue section below and send as SMS to the intercom. For At&T cards from the store, you can use “nxtgenphone”. If you are using a Tracfone provided SIM, then set the APN to “RESELLER”.

9999#38#APNinfo#

Pass code

Function code

APN info for network

Step 1C:Reboot the Intercom

The intercom will need to be rebooted in order to log on to the network with the new APN which you have stored. If you send another reception check (*20#), you may find that if it was on 3G signal strength before, that it is now on 4G signal.

P a g e | 16

Select Multi for multi family system

Note: Keypad codes for residents MUST BE 6 DIGITS LONG!

SMS String:

Step2: Add a Family (up to 100)

Add up to 3 numbers for a family or resident, one code, and up to 3 proximity cards (Note: cards have serial numbers printed on them which can be added to the fields as shown).

Add Optional Prox Cards Add card by serial number as shown.

9999#10#12345#Jones#987654321,987654321,987654321#123456#serial,serial,serial#

Passcode

Apartment number

(up to 6 digits)

Command

(add family)

Family name

(14 digits max)

Phone numbers

(3 max, comma separated)

Keypad code

(must be 6 digits)

Optional PROX card

serial numbers

P a g e | 17

Delete a Family & all details 9999#25#apartmentnumber#

Step2b: Edit family Details if needed

Edit just the name, phone numbers, prox cards or pin code individually for any family with the following buttons..

SMS Strings Change Family Name 9999#11#apartmentnumber#newname# Edit or add first Phone Number 9999#12#apartmentnumber#phonenumber# Edit or add second Phone Number 9999#13#apartmentnumber#phonenumber# Edit or add third Phone Number 9999#14#apartmentnumber#phonenumber#

Edit or Add Family Door Code 9999#15#apartmentnumber#doorcode#

Edit or add family Prox Card 1 9999#16#apartmentnumber#serialnumber# Edit or add family Prox Card 2 9999#16#apartmentnumber#serialnumber# Edit or add family Prox Card 3 9999#16#apartmentnumber#serialnumber#

P a g e | 18

Step4: Add visitor access

You can add visitor keypad codes, or visitor caller ID access, and proximity cards for any visitors who are non-residents.

CallerID (enter by calling intercom and CLIP caller recognition)

Proximity card access for visitors

Keypad code access for visitors

Step3: Activate Auto Sync

If you are using time sensitive features, such as time restricted access control, or auto opening and closing of gates at pre-set times of the day and week, then it is important to activate the auto sync. This intercom reads the current date and time from an incoming SMS message and re-calibrates its time from that.

Activating this button sends the intercom its OWN SIM card phone number. The intercom will then send ITSELF an SMS after a power loss to re-establish correct time.

Use this feature to have the intercom send itself a SMS on a schedule. This is useful to maintain proper time for summer daylight saving for example. NOTE: Network charges may apply for SMS messages. Check with your provider.

SMS Strings

Store Intercom OWN phone number for time sync after reboot 9999#54#SIMphonenumber#

Activate Scheduled SMS 9999#55#days# (00=no SMS, 01=daily, 02=every 2 days etc)

P a g e | 19

A closer look at Keypad codes..

There are 3 types of visitor keypad codes.. 1. 50 permanent codes which can be

used 24/7. 2. 20 temporary codes, which auto

expire in a pre-set number of hours. 3. 20 time restricted codes which can

only be used at pre-set times and days of the week.

SMS Strings

Store permanent code 9999#81#code#time# (code can be 4 digits, time = relay time in secs from 1-99. 0 = latch code)

Store temporary code 9999#82#hours#code# (hours = number of hours a code is active for, from 1 – 999 hours)

Store time restricted code 9999#83#day,day,day#time1,time2# code# (day=mon,tue,wed,thu,fri etc. Time1=start time, Time2= end time. Code = 4 digit keypad code)

Delete Code 9999#84#code# (delete a known code) or 9999#84#*# (delete all stored codes)

Note: Times of day are military format with no colon. E.g. 1130 pm = 1130

P a g e | 20

A closer look at Prox cards

There are 3 types of visitor cards.. 1. 50 permanent cards which can be used 24/7. 2. 20 temporary codes, which auto expire in a

pre-set number of hours. 3. 20 time restricted codes which can only be

used at pre-set times and days of the week.

1234567890

Cards have a 10 digit serial number printed as shown. Enter this to add a card.

SMS Strings

Store permanent code 9999#61#code#time# (code can be 4 digits, time = relay time in secs from 1-99. 0 = latch code)

Store temporary code 9999#62#hours#code# (hours = number of hours a code is active for, from 1 – 999 hours)

Store time restricted code 9999#63#day,day,day#time1,time2# code# (day=mon,tue,wed,thu,fri etc. Time1=start time, Time2= end time. Code = 4 digit keypad code)

Delete Code 9999#64#code# (delete a known code) or 9999#64#*# (delete all stored codes)

P a g e | 21

A closer look at CallerID

IMPORANT: All resident phone numbers that are stored can automatically have callerID access without having to store the numbers in this section again. Go to CONCIERGE/ACCESS CONTROL to activate CallerID for all residents. There are 3 types of CallerID access for VISITORS:

1. 50 visitor phone numbers with 24/7 access. 2. 20 visitors with temporary access (expires

automatically after pre-set time) 3. 20 time restricted phone numbers which can

only be used to gain access at pre-set times and days of the week.

SMS Strings

Store permanent callerID phone numbers 9999#71#Y#phonenumber#time# (Y=1 or 2 for relay 1 or 2. Time = seconds relay is activated)

Store temporary phone number 9999#72#hours#phonenumber# (hours = 1-999 hours then this number is auto deleted again)

Store time restricted phone number 9999#73#day,day,day#time1,time2# phonenumber# (day=mon,tue,wed,thu,fri etc. Time1=start time, Time2= end time)

Delete Phone nunmber 9999#74#code# (delete a known code) or 9999#74#*# (delete all stored visitor numbers)

P a g e | 22

Access Control

If residents are to be able to use callerID to open the gate or door, then enable here. Take care, as residents can miss-dial the intercom in error!

Enable if residents should be able to latch or hold open gates or door. This is not recommended on larger installs as frequently a gate can be latched in error and result in a service call.

Quick delete a resident and all details.

SMS Strings

Enable callerID for residents 9999#35#X# (X=0 to disable. X=1 to enable)

Enable latching ability on received calls by residents 9999#36#X# (X=0 to disable. X=1 to enable)

Quick Delete a resident to prevent access 9999#25#apartment#

Do Not Disturb

On this screen you can prevent residents receiving calls from visitors after a set time at night. This can be useful if there are antisocial callers or residents do not want disturbed at weekends. Enter time in 24hr format, no colon. Eg 8.20am = 0820. 11.40pm = 2340.

Visitors can receive calls BETWEEN the START and FINISH times only on the days selected.

SMS Strings

Enter Concierge / help or assistance number 9999#56#phonenumber#

Delete Concierge / help or assistance number 9999#56#*#

Set ringing time to call number 9999#57#XX# (XX = seconds, default = 20)

P a g e | 23

Auto Opening

You can use the internal time clock feature to hold open gates at pre-set times and days of the week. For gates that are on step by step operation, set trigger times to activate opening and closing. For auto-closing gates, set LATCH times to open, and then set separate UNLATCH times to close again. Up to 9 SMS event messages can be sent in total.

Enter time in 24hr format, no colon. Eg 8.20am = 0820. 11.40pm = 2340.

Toggle between trigger, latch and unlatch

Add Auto opening / closing times 5555#X#day,day,day,day#time#

Manager Pass code

1= Relay 1 trigger

2= Relay 1 latch

3= Relay 1 unlatch

4= Relay 2 trigger

5= Relay 2 latch

6= Relay 2 unlatch

Add days, 3 digits, e.g.

mon,tue,wed,thu,fri,sat,sun.

Separated by comma.

Time in 24hr format. No

colon. E.g. 11.15pm = 2315

SMS Strings

Delete all automatic relay events 5555#*#

P a g e | 24

Enter a number here which will be called when a visitor needs assistance. Useful for car parks and barriers etc.

Calling time to ring the assistance number before cancelling and ending the call.

SMS Strings

Enter Concierge / help or assistance number 9999#56#phonenumber#

Delete Concierge / help or assistance number 9999#56#*#

Set ringing time to call number 9999#57#XX# (XX = seconds, default = 20)

Enquire Resident Info

Enter the apartment or house number and the intercom will reply with all data, numbers and codes stored against that resident.

SMS String

Enquire resident 9999#26#apartment#

Concierge / assistance

Used in panels with a HELP / Assistance or concierge button.

P a g e | 25

More Settings Screen

Check status of relays, signal strength, stored codes and much more.

Adjust speaker & microphone volume

Adjust ringing times before rolling to next phone number

Set global relay trigger times, useful for magnetic locks

Volumes

If residents experience significant echo, reduce the microphone and speaker levels as low as possible. Default setting = 5. Range = 1-9.

SMS Strings

Set Speaker Volume 9999#30#X# (X = 1-9, default = 5)

Set Microphone Volume 9999#31#X# (X = 1-9, default = 5)

Set ring tone Volume (not used yet) 9999#32#XX (X = 1-9, default = 5)

P a g e | 26

Dialling Times

Use these to adjust the ringing time the intercom will call a number before it will stop and call the next. This is useful to avoid voicemail from picking up a call.

Default dialling time is 20 seconds (from button press)

SMS Strings

Set first ringing time 9999#21#XX# (Default = 20. Range = 1-99)

Set second ringing time 9999#22#XX# (Default = 20. Range = 1-99)

Set third ringing time 9999#23#XX# (Default = 20. Range = 1-99)

Relay Times

Adjust relay times to suit perhaps a magnetic lock that requires a 7-10 second unlock time to allow pedestrians time to press the door and open.

Default relay time is 1 second.

P a g e | 27

Information Screen

This screen allows the engineer or manager to be able to check multiple things on the intercom.

Please note the following points..

-5555 is the default managers code shown.

-Stored callerID numbers, keypad codes and prox users are VISITOR credentials only. These do

not list RESIDENT credentials. To do that, enquire on each resident individually in the appropriate

screen.

In the activity log screen, each event is stored under a code. For example if a visitor uses caller ID

to open the gate, it will be shown as date – time – number – CID. If a keypad code is used, it will

be shown on the next line as date – time – pin number – CODE.

P a g e | 28

Manager Controls of Gate / Door This screen allows the installer or manager to manually trigger the gate.

Complete list of parameters

RELAY 2 Momentary trigger SMS – 5555#4#

RELAY 2 Latch / Hold Open SMS – 5555#5#

RELAY 2 Unlatch / Unhold SMS – 5555#6#

RELAY 1 Momentary trigger SMS – 5555#1#

RELAY 1 Latch / Hold Open SMS – 5555#2#

RELAY 1 Unlatch / Unhold SMS – 5555#3#

P a g e | 29

The table below show the complete list of features. Programming messages below must begin with 9999# (assuming 9999 is still the programming passcode)… Edit a family name 9999#11#12345#Jones# Edit or add family number 9999#12#12345#number# (edit first dialled number) 9999#13#12345#number# (edit second dialled number) 9999#14#12345#number# (edit third dialled number) Edit a family door code 9999#15#12345#code# Edit or add a family card 9999#16#12345#serial# 9999#17#12345#serial# 9999#18#12345#serial# Set ringing time to call first number 9999#21#XX# Set ringing time to call second number 9999#22#XX# Set ringing time to call third number 9999#23#XX# Delete a family and all details 9999#25#12345# Enquire details on a family 9999#26#12345# (This will reply with all the details stored about this apartment). Set Speaker Volume 9999#30#X# (X=1-9) Set Mic Volume 9999#31#X# (X=1-9) Enable / Disable caller ID for residents 9999#35#1# (1=ON, 0=OFF. Default=0) Enable / Disable latching ability by residents 9999#36#1# (1=Enabled, 0=Disabled. Default=0) Change Engineers programming code 9999#40#XXXX# (Default 9999) Change managers user code 9999#41#XXXX# (Default 5555) Change Relay 1 trigger time 9999#50#XXXX# Change relay 2 trigger time

P a g e | 30

9999#51#XXXX# Store intercom own phone number for AUTO self SMS sending on reboot. 9999#54#XXXXXXXXXX# Activate auto SMS sending (to re-calibrate time every day) 9999#55#XX# (0=off, 1=SMS every day, 2=SMS every 2 days etc) Store phone number for manager / concierge / assistance call button to call when pressed 9999#56#XXXXXXXXX# Delete manager phone number 9999#56#*# Store ringing time for manager / concierge / assistance phone number 9999#57#XX# SMS control messages Either engineer or of manager can control the relays by SMS but users cannot. 9999#1# - Trigger relay 1 9999#2# - Latch relay 1 9999#3# - unlatch relay 1 9999#4# - Trigger relay 2 9999#5# - Latch relay 2 9999#6# - Unlatch relay 2 Same commands can be carried out with 5555 passcode. To store a visitor code (50 max) 9999#81#1#code#time# (time=relay trigger time, 1-99 seconds) To store a temporary visitor code (20 max): 9999#82#hours#code# (hours is number of hours code is active for, max 999 hours) To store a time restricted visitor code (20 max): 9999#83#day,day,day,day,day,day,day#time1,time2#code# To delete a visitor code: 9999#84#code# To delete all visitor codes: 9999#84#*# To store visitor caller ID number (50 max) 9999#71#Y#telephone# (Y=1 for relay 1, 2 for relay 2) To store visitor temporary called ID number (20 max) 9999#72#hours# telephone # (hours is qty of hours the caller ID number can work for 999 max) To store a visitor time restricted caller ID number (20 max) 9999#73#day,day,day,day,day#time1,time2#telephone# To delete a visitor caller ID number: 9999#74#number# To delete all visitor caller ID numbers:

P a g e | 31

9999#74#*# To store prox card (50 max) 9999#61#Y#serial# (y = 1 or 2 for relay 1 or 2) To store temporary visitor Prox card (20 max) 9999#62#hours#serial# (hours can be up to 999 max) To store time restricted prox card (20 max) 9999#63#day,day,day,day,day#time1,time2#serial# To delete a prox card: 9999#64#serial# To delete All prox card: 9999#64#*# SMS Checking messages *20# (check reception, version and date etc) 5555*21# (Check stored visitor caller ID numbers only. Do not check stored family numbers). 5555*22# (Check gate status) 5555*23# (shows last 20 events) 5555*24# (Check stored visitor keypad codes) 5555*25# (Check stored visitor prox cards) To Add an automatic relay event 5555#1#day,day,day#time# To delete all auto relay events.. 5555#*# To set Do Not Disturb Times 9999#90#day,day,day#time1,time2# Enter optional out of hours number (after times set above, all calls will divert to this number instead: 9999#91#telephone# To delete this number again 9999#91#*# Complete restore defaults on unit 9999#99#

P a g e | 32

Troubleshooting guide

Q. The unit will not power up. No LEDs on.

A. Check power supply voltage at intercom is 23.4v DC or more. Cable length from PSU to

intercom should be less than 25 feet and in 14 gauge for longer distances. See guide. Check the

fuse.

Q. The unit powers up but is not showing network reception or will not respond to SMS.

A. This means the unit is not able to detect the network for some reason.

-Power off the unit, remove the SIM and check it in a mobile phone to verify it can make a call and

has calling credit.

-Disable any PIN code request if active on the SIM card.

-Check the SIM is a standard voice capable SIM. If you are unsure, contact your SIM card

provider to verify. Compatible networks are At&T and T-Mobile.

-Check the reception is medium or good. Poor reception is not sufficient.

-Power off, remove the SIM, use fine sand paper to lightly sand the SIM pads and contacts on the

GSM unit, lightly bend the contacts upwards so that they make better contact with the SIM and try

again.

Q. The unit calls the first number, but there is not enough time to answer before it diverts

to the next number.

A. Increase the no answer time as per programming instructions.

Q. The unit calls the first number but voicemail comes on before it can ring the second

number.

A. Decrease the no answer time as per programming instructions.

Q. The caller ID part does not work.

A. Residents have Caller ID disabled by default. Ensure this is activated if you want residents to

use caller ID. If your number is a private or number withheld, then it will not work.

-Ensure the number is entered as you would normally dial it from another phone.

-For US customers, ensure the numbers have been entered with a leading 1. If this does not work,

try again without the leading 1.

Q. There is no audio from the gate, but the person at the gate can hear ok.

A. This can be due to low reception or excessively long power cables.

-Check reception level by *20#.

-Change SIM card if necessary to another network which may have better coverage.

-Purchase a high gain antenna.

This may also be caused by a defective microphone, water on a microphone from a sprinkler for

example, or dirt/insects blocking the microphone hole. If reception is optimum and the problem

persists, contact your supplier or installer.

Q. The audio quality that can be heard on the remote telephone is poor or humming

(buzzing).

A. A small amount of GSM buzz can be considered normal on GSM intercoms, but not so much

that causes inability to hear the person speaking. This is a symptom of poor reception. Try above

steps on checking and improving reception. Consider fitting an external high gain antenna. Move

P a g e | 33

the antenna further away. Remove any short bends in the antenna. Ensure the spare antenna

cable is not rolled up inside the call station.

Q. The trigger keys do not work when the intercom calls a phone.

A. Check if you can hear the relay clicking at the gate when the keys are pressed during a call. If it

can be heard, then the system is working, check wiring between the relay and the lock or gate

panel. If the relays do not make a clicking sound, then check this feature on a different mobile cell

phone or landline. If it works on a different phone, check the settings on the phone in question

under DTMF tones.

Failure of DTMF tones to operate correctly is also a symptom of low reception or insufficient

power cabling. Check steps above on improving reception or addressing the power problem.

-Also check that the relays are not already latched with the *22# command. If they are latched,

they need unlatched before the trigger keys will work.

-Sometimes excessively long power cables or thin power cables can cause this problem. Prove it

by connecting a temporary extension lead and the power supply directly to the unit.

Q. The system was operating the gates fine, but now it will not trigger the gates.

99% of the time, this is cause by the user accidentally latching the relay. This latches the output

relay permanently on. Send the intercom the following SMS *22#. The intercom should reply with

a message detailing the relay status.. If it has been latched, then the message will state “the relay

is ON”. In this case refer to the user guide to read how to unlatch it again.

Q. The unit no longer calls out to phones but I can make a call to it from my phone.

A – Check there is balance on the SIM card.

A – Switch off the power, remove the SIM, put it into a phone, and check that a call can be made

from a phone. This will verify if the SIM is still working and in service.

Q. The Android App shows an error message “Command Failed” when I try to use a

function.

A – Go to phone settings/application manager/cellbox prime/permissions, and ensure all

permissions are turned ON. Also ensure the app settings screen has a valid phone number

stored.

Change History Key: P = Panel version H = Hardware PCB version S = Software version

Version Reason for change Date

P H S

1 1 2.6

P a g e | 34

Warranty Terms Please note, by installing this product, you are accepting the following warranty terms:

1. The manufacturer’s warranty is a “return to base” 2 year warranty from date of manufacture. This means that

any suspected defective components or items are returned to the manufacturer’s agent for investigation and

diagnosis, and returned at the cost of the customer.

2. The warranty does not cover, nor is the manufacturer or agent responsible for any of the following

whatsoever: Storm damage, lightning or surge damage, flooding, accidental damage, vandalism or deliberate

damage, un-explained corrosion or unusually harsh environments, failure of telephone networks, future un-

interoperability between the product and network providers which cause mal-function due to changes

implemented by the phone providers after manufacture of the product, or that which is outside of control of the

manufacturer (e.g. 2G, 3G switch off, removal or inability to obtain VOLTE service), and damage due to not

proper installation.

3. The manufacture in no way accepts liability for any of the following incurred due to a product defect: Cost of

attending site, inconveniences, labour rates, time lost, loss to or damage to property, security breaches, late

payment clauses or breaches of any contracts between the installer and the client.

4. This is a profession install product only. The product is a component of an overall system. Therefore, it is the

responsibility of the installer to certify the safety and compliance of the overall finished system. As soon as this

product is fixed to another item, or connected to another third-party device, then the product has been modified,

and compliance with local regulations in the country of install is strictly the responsibility of the installer.

5. Re-stocking fees may apply to items returned that are found to be non-defective. Complete units will also

attract a re-stocking fee if returned for credit, regardless if a defect is discovered or not. Re-stocking fees may

vary depending on the condition of the item being returned, and whether it can be determined as in brand new

condition. The warranty terms do not entitle customers to an automatic full refund. For more details on returns

procedures and re-stocking fees, contact the agent.

6. Items with physical signs of surge damage are not covered by warranty. Items without visible signs of surge

damage will only be covered by warranty provided photographic evidence is provided from site showing surge

protection has been installed as per instructions in this manual.

FCC ID: 2ALPX-PE-4GA Main Model No: PRIME6-PROX-IMPK-PE-4GA

Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

P a g e | 35

P a g e | 36

Note: For legal reasons, telephone technical support is for registered

and qualified product dealers only. Home owners and end users should

contact their local dealer for product technical support.

www.BFTGateOpeners.com | (800) 878-7829 | Sales@BFTGateOpeners.com