Upload
others
View
19
Download
0
Embed Size (px)
Citation preview
Installing a Net2 access control unit
The diagram below shows the general wiring layout for a Net2 plus ACU. Not all of the equipment shown needs to be installed on every door. For example, when using Timesheet it is only necessary to install a reader and the data connection.
The selection of ACU type and their method of connection to the Net2 server PC (TCP/IP, RS485, wireless, etc) can be combined in one system to meet the needs of any site layout.
Special attention should be paid to the installation of the lock to ensure correct operation, either fail open or fail closed. Exit buttons must always be of the 'push to make' variety. Door contacts, tamper switches and PSU monitoring circuits should all be normally closed, going open on alarm.
Overview
0V
Net2 plus
0V
0V
0V
0V
0V
PSU
OK
0V
0V
ARM
SENSE
N.C.
N.O1
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485Media
Detect
0V
10
TX RX
100
Data/D0
Clock/D1
Media Detect
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXITEXIT
PSU
12V DC
12V DC I
0V
Net2 plus
0V
0V
0V
0V
0V
PSU
OK
0V
0V
ARM
SENSE
N.C.
N.O1
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485Media
Detect
0V
10
TX RX
100
Data/D0
Clock/D1
Media Detect
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXITEXIT
PSU
12V DC
12V DC I
0V0V
0V
0V
N.C.
N.O
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485
0V
10
TX RX
100
Data/D0
Clock/D1
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXIT
12V DC
12V DC I
1PaxtonN
et2 plus
0V0V
0V
0V
N.C.
N.O
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485
0V
10
TX RX
100
Data/D0
Clock/D1
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXIT
12V DC
12V DC I
1PaxtonN
et2 plus
0V0V
0V
0V
N.C.
N.O
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485
0V
10
TX RX
100
Data/D0
Clock/D1
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXIT
12V DC
12V DC I
1PaxtonN
et2 plus
Reader/keypad(optional)
Reader/keypad
from previous ACU
to next ACU
Tamper switch (optional)
Exit button (push to make)
Normally closed door contact
(optional)
Door Lock
12V DC power supply
TCP/IP patch lead
AN1012Net2
1
2
AN1012Net2
Communication
By far the most common cause of problems with Net2 installations, is incorrect wiring of the data/network connection. When using an RS485 dataline, it is extremely important that the following simple rules are followed for each controller on the line and that the line is terminated correctly.
Termination resistors (120 ohm) must be linked across both data pairs at the beginning AND end of the data line. This can be done on many units with a switch or jumpers. If not, free resistors are provided with the data converter. If the converter is located at a point along the data line, termination will only be required in the two ACU's at each end of the line.
Any spare cores and the cable screen must be connected to the network screen terminal. This provides a common 0V reference for all of the controllers on the data line.
The data line must loop in and out of each controller using the same coloured cores for each unit. CAT5 colour codes are shown on the controller's wiring label. The controllers must be installed in one continuous daisy chain.
A Net2 plus can connect to the Net2 PC using either a standard TCP/IP Ethernet RJ45 cable or an RS485 data line. This greatly increases the number of installation options available to the installer.
Net2 plus can also be used as the TCP/IP interface for a daisy chain of other Net2 plus or Net2 classic units.
A TCP/IP connection must first be detected using the Net2 Server Configuration utility in the same manner as a TCP/485 converter. When used on an RS485 data line, any required termination resistors are linked across the data pairs by a simple slide switch.
A dedicated Intruder Alarm connection is provided.
The Net2 nano is a wireless based access control unit. It connects to the central administration PC using Paxton proprietary and secure wireless technology (Net2Air). Net2 nano control units can be mixed with other Net2 control units and so can be added to existing Net2 installations.The unit has a dedicated 12V DC lock output (incorporating an integrated diode), an Alarm output and a separate voltage free relay. Exit buttons, door contacts, tamper switches and mains failure alarms can all be connected.
Control units communicate to the PC via a Net2Air bridge. These come in USB and Ethernet variants so a site may be covered by several bridge units at different locations.
The Net2Air protocol is based on the standard known as IEEE 802.15.4. It operates at 2.4GHz and can co-exist with wireless LAN networks and other devices using this frequency.
Net2 plus
Net2 nano
3
AN1012Net2
V21
V0 V21
V0 V21
V0 USP
V0
12V 7Ah
INPUT AC 100-240V 50 / 60 Hz 1.2AOUTPUT DC 13.8V 2A
0V
Net2 plus
0V
0V
0V
0V
0V
PSU
OK
0V 0V
ARM
SENSE
N.C.
N.O1
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485Media
Detect
0V
10
TX RX
100
Data/D0
Clock/D1
Media Detect
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXITEXIT
PSU
12V DC
12V DC I
1 r
edae
R
:no
itua
Cyl
no s
reda
er
CD
V21
roF
2 r
edae
R
12V
Red LED
Amber LED
Green LED
Data/D0
Clock/D1
Media Detect
0V
0V
12V
Red LED
Amber LED
Green LED
Data/D0
Clock/D1
Media Detect
0V
N.C.
N.O.
COM
N.C.
N.O.
COM
Alarm
12V
Green LED
Exit
0V
stupnItp
uts
uO
rewoP
0V12V
Contact
0V
0V
Tamper
PSU
repmaT/
USP
tcatnoC
nottuB tixE
2 yaleR
1 yaleR
Expansion
RxTx
RS485 NetworkCAT5 Cable Coding
nrG/
thW
era
p s r
o n e
erc
S a
t ad
morf
ser
oce l
bac
neer
G
gnr
O/t h
W
egn a
rO
10/100 Ethernet
Server Connected
Server Link10010
End of Line Termination
ON OFF
Net2 plusIntruder Alarm
Set
V0mrA
esne
S
MO
C
.O.
N
LABEL HERELABEL HERE
http://paxton.info/107
12345600-01-02-03-04-05
2345612 1 r
edae
R
:n o
i tua
Cyl
no s
reda
e r
CD
V21
roF
2 r
eda e
R
.
stupnItp
uts
uO
rewoP
0V
repmaT/
USP
tcatnoC
nottuB tixE
2 yaleR
1 yaleR
RxTx
RS485 NetworkCAT5 Cable Coding
nrG/
thW
erap
s r o
nee
rcS
atad
m o
rf s
eroc
elba
c
neer
G
gnr
O/t h
W
egn a
rO
10/100 Ethernet
Server Connected
Server Link 10010
End of Line Termination
ON OFF
Net2 plusIntruder Alarm
DC O
nly
Set
V0
12-24V
mrA
snS
MO
C
.O.
N
12345600-01-02-03-04-05
2345612http://paxton.info/107
0V0V
0V
0V
N.C.
N.O
2
COM
N.C.
N.O
COM
Data/D0
Clock/D1
CAT5 RS485
0V
10
TX RX
100
Data/D0
Clock/D1
10/100 Ethernet
N.C.
N.O
COM
12V - 24V
12V
1
2
12V
LED
LED
LED
12V
LED
LED
LED
LED
EXIT
12V DC
12V DC I
1PaxtonN
et2 plus
Installation of an ACU in a PSU enclosure
The best way to install a Net2 ACU is in the specially designed Paxton power supply enclosure. This unit contains a 2A 12V DC power supply, a charging circuit for battery back up and an enclosure tamper switch.
Alarm messages will be reported to the Net2 server if the lid of the ACU is opened (tamper) or if the mains supply to the unit fails (this alarm will only work successfully if battery back up is fitted).
Back-up battery
PSU
Tamper Switch
12V DC Outputs
Mains failure monitoring
Links to online documentation
For further information about a specific ACU or advice on the communication methods available, please see the following:
X Ins-30080 - Net2 plus control unit < http://paxton.info/924 >X Ins-30075 - Net2 nano control unit < http://paxton.info/710 >
X AN1077 - Net2 plus - how does it work? < http://paxton.info/1584 >X AN1095 - Net2 nano - how does it work? < http://paxton.info/974 >
X AN1040 - Installing a Net2 data line < http://paxton.info/877 >X AN1006 - Installing remote sites using TCP/IP < http://paxton.info/51 >X AN1096 - How to plan a Net2 nano installation < http://paxton.info/975 >
MAI
NS
POW
ER