INSTRUCTION MANUAL MODELS 968 & 968D - Huck Toolshuck-tools.com/assets/images/huck-968-manual.pdf · 2015-12-10 · Description of Machinery: ... should be done by a qualified repairman

July 15, 2014HK1126

INSTRUCTION MANUAL

MMODELSODELS 968 & 968D968 & 968D

POWERIG® HYDRAULIC UNIT

968

968D

968 series Powerig ® (HK1126) Alcoa Fastening Systems

2

EC Declaration of ConformityManufacturer:

Alcoa Fastening Systems, Industrial Products Group, 1 Corporate Drive, Kingston, NY,

12401, USA

Description of Machinery:

PA46 series (968 and 968D) Powerig®

Relevant provisions complied with:

EN, EN-ISO, ISO standards Title

Per the provisions of the Machinery Safety Directive 2006/42 EC

EN_ISO 12100-1 Basic concepts, general principles for design - Part 1

EN_ISO12100-2 Basic concepts, general principles for design - Part 2

EN 982 Safety requirements for fluid power systems & their com-

ponents - Hydraulics

EN 983:1996 Safety requirements for fluid power systems & their com-

ponents - Pneumatics

EN ISO 13849-1:2008 Safety-related parts of control systems - Part 1

EN ISO 13849-2:2008 Safety-related parts of control systems - Part 2

EN ISO 14121-1:2007 Risk assessment - Part 1

European Representative:

Rob Pattenden, Huck International, Ltd. Unit C Stafford Park 7, Telford Shropshire TF3 3BQ,

England, United Kingdom

Authorized Signature/date:

I, the undersigned, hereby declare that the equipment specified above conforms to the above

European Communities Directive(s) and Standard(s).

Signature:

Full Name: Larry M. Krieg

Position: Engineering Manager

Installation Systems Division

Place: Kingston, New York, USA

Date: June 2012

Test data to support the above information is on file at Alcoa Fastening Systems, Industrial Products Group, KingstonOperations, Kingston, NY, USA.


3

CCONTENTSONTENTS

SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

PRINCIPLE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPTIONAL EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

ADDITIONAL SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .7

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

TOOL TO POWERIG SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

PARTS DRAWINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12


4

1. A half hour long hands-on training session with qualified per-

sonnel is recommended before using Huck equipment.

2. Huck equipment must be maintained in a safe working condi-

tion at all times. Tools and hoses should be inspected at the

beginning of each shift/day for damage or wear. Any repair

should be done by a qualified repairman trained on Huck pro-

cedures.

3. Repairman and Operator must read manual prior to using

equipment. Warning and Caution stickers/labels supplied with

equipment must be understood before connecting equipment

to any primary power supply. As applicable, each of the sec-

tions in this manual have specific safety and other information.

4. Read MSDS Specifications before servicing the tool. MSDS

Specifications are available from the product manufacturer or

your Huck representative.

5. When repairing or operating Huck installation equipment,

always wear approved eye protection. Where applicable, refer

to ANSI Z87.1 - 2003

6. Only genuine Huck parts shall be used for replacements or

spares. Use of any other parts can result in tooling damage or

personal injury.

7. If a part affixed with warning labels is replaced, or labels are

missing or damaged, the end user is responsible for replace-

ment. Refer to assembly drawing and parts list for replace-

ment part number and proper placement.

8. Disconnect primary power source before performing mainte-

nance on Huck equipment or changing Nose Assembly.

9. Tools and hoses should be inspected for leaks at the begin-

ning of each shift/day. If any equipment shows signs of dam-

age, wear, or leakage, do not connect it to the primary power

supply.

10. Mounting hardware should be checked at the beginning of

each shift/day.

11. Make sure proper power source is used at all times.

12. Release tool trigger if power supply is interrupted.

13. Tools are not to be used in an explosive environment unless

specifically designed to do so.

14. Never remove any safety guards or pintail deflectors.

15. Where applicable, ensure deflector or pintail collector is

installed and operating prior to use.

16. Never install a fastener in free air. Personal injury from fasten-

er ejecting may occur.

17. Where applicable, always clear spent pintail out of nose

assembly before installing the next fastener.

18. There is possibility of forcible ejection of pintails or spent man-

drels from front of tool.

19. Check clearance between trigger and work piece to ensure

there is no pinch point when tool is activated. Remote triggers

are available for hydraulic tooling if pinch point is unavoidable.

20. Unsuitable postures may not allow counteracting of normal

expected movement of tool.

21. Do not abuse tool by dropping or using it as a hammer. Never

use hydraulic or air lines as a handle or to bend or pry the

tool. Reasonable care of installation tools by operators is an

important factor in maintaining tool efficiency, eliminating

downtime, and in preventing an accident which may cause

severe personal injury.

22. Never place hands between nose assembly and work piece.

Keep hands clear from front of tool.

23. There is a risk of crushing if tool is cycled without Nose

Assembly installed.

24. Tools with ejector rods should never be cycled with out nose

assembly installed.

25. When two piece lock bolts are being used always make sure

the collar orientation is correct. See fastener data sheet for

correct positioning.

26. Tool is only to be used as stated in this manual. Any other use

is prohibited.

27. There is a risk of whipping compressed air hose if tool is pneu-

draulic or pneumatic.

28. Release the trigger in case of failure of air supply or hydraulic

supply.

29. Use only fluids or lubricants recommended.

30. Disposal instruction: Disassemble and recycle steel, aluminum

and plastic parts, and drain and dispose of hydraulic fluid in

accordance with local lawful and safe practices.

31. If tool is fixed to a suspension device, ensure that the device is

secure prior to operating the tool.

GLOSSARY OF TERMS AND SYMBOLS:

- Product complies with requirements set forth by the rel-

evant European directives.

- READ MANUAL prior to using this equipment.

- EYE PROTECTION IS REQUIRED while using this

equipment.

- HEARING PROTECTION IS REQUIRED while using

this equipment.

Notes: are reminders of required procedures.

Bold, Italic type and underlining: emphasizes a specific instruc-

tion.

SSAFETYAFETY I INSTRUCTIONSNSTRUCTIONS

CAUTIONS: show conditions that will

damage equipment and or structure.

WARNINGS: Must be understood to avoid

severe personal injury.


5

DDESCRIPTIONESCRIPTION

The Huck Model 968 POWERIG® is a portable, airpowered hydraulic power source designed tooperate Huck Hydraulic Installation Equipment.

Hydraulic pressure is developed by two hydraulicpiston pumps driven by air motors. Pump outputis directed to either PULL or RETURN pressureports of the installation tool by air operated direc‐tional valve. The hydraulic unit is controlled, withair trigger, from the tool.

Internal relief valves are pre‐set at the factory forthe protection of operator and equipment. External relief valves control PULL Pressure andRETURN Pressure. As shipped from the factory,

external relief valve is set at 5400‐5700 psi(37200‐39300 kPa) and return pressure valve isset at 2700‐3300 psi (15200‐16500 kPa).Pressures are adjustable to match Huck installa‐tion tool being used. See applicable installationtool manual.

Hydraulic fluid is stored in a reservoir. Hydraulicquick disconnect couplers are furnished for con‐necting installation tool.

The unit weighs approximately 75 pounds (34 kg)without the optional dolly assembly, and whenfilled with hydraulic fluid.

��

� ��

��

��

��

��

��

��

PPRINCIPLERINCIPLE OFOF O OPERATIONPERATION

When tool trigger is depressed, the directionalvalve changes positions so that high‐pressurehydraulic fluid is directed out the PULL pressureport and hose to tool 1.

When the tool trigger is released, the valve spoolreturns to its original position, directing thehydraulic fluid out the RETURN pressure port andhose to the tool.

Reservoir SightGlass


6

Width 16.33 (41.5 cm)

Length 10.45 (26.5 cm)

Height 15.68 (39.83 cm)

Weight 75 lbs. (34 kg)

Operational Weight 93 lbs. (42 kg)

Power Source Air supply must be minimum 50

CFM (.024 m3/s)

Hose Kits Use only genuine HUCK Hose Kits rated

@ 10,000 psi working pressure.

Reservoir Capacity 2.5 gallons (9.5 liters)

Output Pressure

PULL (max): 8800 psi (606 bar)RETURN (max): 3500 psi (241 bar)

Max Operating Temp 125 ° F ( 51.7 ° C)

Max Flow Rate 1.95 gpm per circuit ( 7.37 l/m)

Hydraulic Fluid ATF meeting DEXRON III, DEXRON

IV, MERCON, Allison C-4 or equivalent specifications.

Fire resistant hydraulic fluid may also be used, and is

required to comply with OSHA regulation 1926.302

paragraph (d): "the fluid used in hydraulic power tools

shall be fire resistant fluid approved under schedule

30 of the US Bureau of Mines, Department of Interior,

and shall retain its operating characteristics at the

most extreme temperatures to which it will be

exposed."

Declared dual number noise emission values in

accordance with ISO 4871:

A weighted sound power level, LWA: 107 dB (refer-

ence 1 pW) Uncertainty, KWA: 3 dB

A weighted emission sound pressure level at the work

station, LpA: 96 dB (reference 20 µPa) Uncertainty,

KpA: 3 dB

C-weighted peak emission sound pressure level, LpC:

108 dB (reference 20 µPa) Uncertainty, KpC: 3 dB

Values determined according to noise test code ISO

15744, using as basic standards ISO 3744 and ISO

11203.

OOPTIONALPTIONAL E EQUIPMENTQUIPMENT

SSPECIFICATIONSPECIFICATIONS

Shown here is the 968D.

This is the 968 Powerig with the

optional Dolly Assembly, Huck part

number 129703 which offers

convenient portability.

Note: Prior to use, make sure

casters are locked.


7

AADDITIONALDDITIONAL S SAFETYAFETY P PRECAUTIONSRECAUTIONS

HYDRAULIC HOSES

1. Before operating the pump, all hose connections

must be tightened using the proper tools. Do

NOT overtighten. Connections need only be

secure and leak-free. Overtightening may cause

premature thread failure or may cause high

pressure fittings to split at pressures lower than

their rated capacities.

2. If a hydraulic hose ever ruptures, bursts, or

needs to be disconnected, immediately shut off

the pump. Never attempt to grasp a leaking

hose under pressure with your hands. The force

of escaping hydraulic fluid could cause serious

injury.

3. Do not use the hose to move attached equip-

ment. Stress may damage the hose and possibly

cause personal injury.

AIR MOTOR

1. Disconnect the air supply when the pump is not

is use or when breaking any connection in the

hydraulic system.

2. It is recommended that a shut-off valve or quick

disconnect be installed in the air line to the

pump unit. Close the shut-off valve before con-

necting the air line to the pump.

OOPERATINGPERATING I INSTRUCTIONSNSTRUCTIONS

FIRST TIME USE

1. Remove shipping plug from top of Reservoir and

replace with Filler Breather Cap. (Fig. 1) Be sure

O-ring is in place on Filler Breather Cap before

installing.

2. Fill reservoir with hydraulic fluid, approximately 2

quarts (1.9 liters), until the fluid level is within one

inch of the top of the reservoir.

3. Use a T-gauge, Huck part no. T-124833CE, to set

Pull and Return pressures to the appropriate val-

ues for the installation tool.

4. Attach installation tool to Powerig. Be sure that

hose from PULL PRESSURE on the unit runs to

port "P" of the tool and hose from RETURN

PRESSURE on the unit runs to port "R" of the

tool.

5. Connect air supply.

6. Depress tool switch and let unit operate for a few

minutes to circulate hydraulic fluid and remove air

from the system.

7. Check fluid level in reservoir and add hydraulic

fluid as required.

8. The unit and installation tool are now ready for

attaching the applicable nose assembly and the

installation of Huck fasteners.

AIR SUPPLY HOOK-UP

Minimum air supply must be 50 CFM (.57 M3/min.)

and 80 PSI (6-7 BAR), with 100 PSI (XX BAR) being

the maximum.

1. Secure pump fitting to the air supply.

2. Assemble the hoses. Clean the areas around the

oil ports of the valve and hydraulic cylinders, and

remove the plastic thread protectors. Clean all

hose ends, couplers, or union ends. Inspect all

threads and fittings for signs of wear or damage

and replace as needed.

3. FILL the RESERVOIR: Remove the filler cap and

insert a clean funnel. Fill the reservoir with

hydraulic oil to top of sight glass. Replace the

filler cap with the breather hole open.


8

TTOOLOOL TOTO P POWERIGOWERIG S SETUPETUP

NOTE: To decrease Relief Valve pressure, turnthe Relief Valve handle gradually counterclock-wise; turn clockwise to increase pressure.

1. With the Nose Assembly in place on theInstallation Tool, begin setup. First connect theHydraulic Hoses to the Powerig.

2. Set Pull and Return pressures on Powerig using

Huck Gage P/N: T-124833CE according to pres-

sure settings recommended with tool to be used.

3. Once the system is set up, install test fastener.

Check to be sure that the fastener is installed

correctly. This can be checked by inspecting the

dimples on the collar flange. At least one dimple

should be marked by the anvil.

WARNING: Only use compatible equip-

ment with this Powerig.

WARNING: To prevent tripping hazard,

suspend tools and route hoses off of

floors.

WARNINGS:

Read full manual before using tool.

A half-hour training session with qualified

personnel is recommended before using

Huck equipment.

When operating Huck installation equip-

ment, always wear approved eye protec-

tion.

Be sure there is adequate clearance for

the operator’s hands before proceeding.

WARNING: Correct PULL and RETURN

pressures are required for operator’s

safety and for Installation TooI’s function.

Gage part number T-124833CE is available

for checking pressures. See Tool

SPECIFICATIONS and Gauge Instruction

Manual. Failure to verify pressures may

result in severe personal injury.

WARNING: Be sure to connect Tool’s

hydraulic hoses to POWERIG Hydraulic

Unit before connecting Tool’s switch con-

trol cord to unit. If not connected in this

order, severe personal Injury may occur.


9

GOOD PRACTICES

The introduction of foreign material into the hydraulic

system will result in poor performance and repair

downtime. To avoid this, observe the following good

practices:

1. When filling reservoir with hydraulic fluid, clean

area around filler cap before removing. Always filter

hydraulic fluid using a 10-15 micron filter before

adding to powerig.

2. Use clean funnel with filter.

3. Do not let hose fittings or couplings lie, or drag on

floor.

4. Wipe off couplings before connecting them.

5. Periodically, drain and clean reservoir and fill with

clean fluid.

REGULAR USE

Before using Hydraulic Unit:

1. Check hydraulic fluid level in reservoir and add fluid

as required.

2. Inspect hoses for damage and replace as required.

3. Check entire system for leaks and repair as needed

MMAINTENANCEAINTENANCE

LUBRICATION OF THE AIR-DRIVEN MOTOR

If the pump is operated on a continuous duty cycle

or at maximum speed for an exteded period, an

automatic air line oiler is recommended. Install the

oiler in the air inlet line as close to the pumping unit

as possible. Adjust the oiler to feed 1-3 drops of

SAE #10 oil per minute (one drop for every 50-75

CFM of air) into the system.

HYDRAULIC FLUID LEVEL

Check the oil level in the reservoir after each 10

hours of use. Proper oil level is to top of sight

glass.

ADDING OIL TO THE RESERVOIR

Use only recommended hydraulic fluid. Disconnect

power supply when adding oil to the reservoir.

Clean the entire area around the filler plug before

removing the filler plug. Use a clean funnel with fil-

ter when adding oil.

MAINTENANCE CLEANING

Keep the outer surface of the pump, all hose con-

nections and any equipment hooked up to the

pump as free of dirt and oil as possible. The

breather hole in the filler cap must be kept clean

and unobstructed at all times. All unused couplers

are to be sealed with thread protectors. Change oil

as recommended.

PPREVENTIVEREVENTIVE M MAINTENANCEAINTENANCE


10

PPARTSARTS D DRAWINGSRAWINGS

��

��

��

�

��

�

��

��

��

� ��

�

��

�

��

��

��

��

�

�

�

Item

D

escri

pti

on

Part

No

.Q

ty.

1C

over

Pla

te A

ssy

130140

1

2R

eserv

oir G

asket

130141

1

3M

oto

r B

ase G

asket

130142

2

4A

ir M

oto

r130143

1

5M

oto

r S

haft C

ouplin

g130145

1

6D

rain

130146

1

7P

lug F

itting

508485

1

8N

ut

506457

1

9O

-Rin

g508486

1

10

Mu

ffle

r508487

111

Sig

ht

Gauge

508488

112

Air V

alv

e130148

1

13

Air V

alv

e,

3-w

ay

130149

1

14

Elb

ow

Tube F

itting

508483

9

15

Str

aig

ht

Fitting

508484

116

Str

aig

ht

Fitting

508489

117

Bre

ath

er

Fitting

508490

118

Te

e F

itting

508491

319

Flo

w C

ontr

ol V

alv

e130150

120

Te

e F

itting

508492

121

Rear

Cover

Base

129504

1


11

PPARTSARTS D DRAWINGSRAWINGS continued

��

��

�

�

�

�

��

��

Item

D

escri

pti

on

Part

No

.Q

ty.

22

Fro

nt

Cover

Base

129505

1

23

Top C

over

129506

1

24

Valv

e S

upport

Bra

cket

129508

2

25

Elb

ow

Fitting

508493

1

26

Str

aig

ht

Fitting

508494

1

27

Male

Fitting

508495

1

28

Str

aig

ht

Fitting

508496

1

29

Tee F

itting

508497

1

30

Plu

g F

itting

508498

1

31

Str

aig

ht

Fitting

508499

132

Quic

k C

ouple

r508500

133

Pull

Handle

130147

1

34

Relie

f V

alv

e C

over

129690

1

35

Pro

duct

Decal

590532

9

36

Trigger

Decal

590520

137

Air I

nle

t D

ecal

590519

138

Caution P

ull

Decal

590533

139

Caution R

etu

rn D

ecal

590534

340

CE

Decal

590535

141

Huck A

ddre

ss D

ecal

590347

142

Tubin

g,

Bla

ck

508501

1


12

TTROUBLESHOOTINGROUBLESHOOTING

NOTE: Use the proper gauges and equipment when troubleshooting. Depending on the pump

version, it is often best to check for leaks by using a hand pump and applying pressure to the

suspect area without the motor running. Watch for leaking oil and follow it back to its source.

Plug the outlet ports of the pump when checking for leakage to determine if the leakage is in

the pump or if it is in the cylinder or tool.

1. Tool fails to operate when trigger is depressed.a. Loose or faulty air connectors on control hose.b. Loose or faulty hydraulic hose couplings.c. Defective tool air trigger assembly.d. Air trigger sensitivity needs adjusting.e. Low hydraulic fluid level in reservoir.f. Hydraulic fluid viscosity too heavy to pick up prime.g. Clogged suction screen.h. Defective hydraulic pump.i. Defective spool valve assembly. j. Installation tool defective

2. Tool does not return on release of trigger.a. Defective spool valve.b. Installation tool not operating properly.c. Air trigger sensitivity needs adjusting.d. Hoses not coupled properly.e. Return pressure set to low.

3. Pump runs but will not build pressure.a. Low hydraulic fluid level in reservoir.b. Clogged suction screen.c. Hydraulic fluid viscosity too heavy to pick up prime.d. Pump check valve is leaking.e. Defective air motor.f. Pull pressure set too low

4. Tool operation slow but entire cycle does occur.a. Pump check valve is leaking.b. Hydraulic fluid viscosity too thin.c. Defective spool valve assembly.d. Clogged suction screen.e. Defective air motor.f. Internal or external relief valve not operating properly.


13

LLIMITEDIMITED W WARRANTIESARRANTIES

TOOLING WARRANTY:Huck warrants that tooling and other items (excluding

fasteners, and hereinafter referred as "other items")

manufactured by Huck shall be free from defects in

workmanship and materials for a period of ninety (90)

days from the date of original purchase.

WARRANTY ON "NON STANDARD OR CUSTOM

MANUFACTURED PRODUCTS":With regard to non-standard products or custom man-

ufactured products to customer's specifications, Huck

warrants for a period of ninety (90) days from the date

of purchase that such products shall meet Buyer's

specifications, be free of defects in workmanship and

materials. Such warranty shall not be effective with

respect to non-standard or custom products manufac-

tured using buyer-supplied molds, material, tooling

and fixtures that are not in good condition or repair

and suitable for their intended purpose.

THERE ARE NO WARRANTIES WHICH EXTEND

BEYOND THE DESCRIPTION ON THE FACE

HEREOF. HUCK MAKES NO OTHER WAR-

RANTIES AND EXPRESSLY DISCLAIMS ANY

OTHER WARRANTIES, INCLUDING IMPLIED

WARRANTIES AS TO MERCHANTABILITY OR AS

TO THE FITNESS OF THE TOOLING, OTHER

ITEMS, NONSTANDARD OR CUSTOM MANUFAC-

TURED PRODUCTS FOR ANY PARTICULAR PUR-

POSE AND HUCK SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE, DIRECTLY OR INDI-

RECTLY, ARISING FROM THE USE OF SUCH

TOOLING, OTHER ITEMS, NONSTANDARD OR

CUSTOM MANUFACTURED PRODUCTS OR

BREACH OF WARRANTY OR FOR ANY CLAIM

FOR INCIDENTAL OR CONSEQUENTIAL DAM-

AGES.

Huck's sole liability and Buyer's exclusive remedy for

any breach of warranty shall be limited, at Huck's

option, to replacement or repair, at FOB Huck's plant,

of Huck manufactured tooling, other items, nonstan-

dard or custom products found to be defective in

specifications, workmanship and materials not other-

wise the direct or indirect cause of Buyer supplied

molds, material, tooling or fixtures. Buyer shall give

Huck written notice of claims for defects within the

ninety (90) day warranty period for tooling, other

items, nonstandard or custom products described

above and Huck shall inspect products for which such

claim is made.

TOOLING, PART(S) AND OTHER ITEMS NOT MANU-

FACTURED BY HUCK:HUCK MAKES NO WARRANTY WITH RESPECT

TO THE TOOLING, PART(S) OR OTHER ITEMS

MANUFACTURED BY THIRD PARTIES. HUCK

EXPRESSLY DISCLAIMS ANY WARRANTY

EXPRESSED OR IMPLIED, AS TO THE CONDI-

TION, DESIGN, OPERATION, MERCHANTABILITY

OR FITNESS FOR USE OF ANY TOOL, PART(S),

OR OTHER ITEMS THEREOF NOT MANUFAC-

TURED BY HUCK. HUCK SHALL NOT BE LIABLE

FOR ANY LOSS OR DAMAGE, DIRECTLY OR INDI-

RECTLY, ARISING FROM THE USE OF SUCH

TOOLING, PART(S) OR OTHER ITEMS OR

BREACH OF WARRANTY OR FOR ANY CLAIM

FOR INCIDENTAL OR CONSEQUENTIAL DAM-

AGES.

The only warranties made with respect to such tool,

part(s) or other items thereof are those made by the

manufacturer thereof and Huck agrees to cooperate

with Buyer in enforcing such warranties when such

action is necessary.

Huck shall not be liable for any loss or damage result-

ing from delays or nonfulfillment of orders owing to

strikes, fires, accidents, transportation companies or

for any reason or reasons beyond the control of the

Huck or its suppliers.

HUCK INSTALLATION EQUIPMENT:Huck International, Inc. reserves the right to make

changes in specifications and design and to discontin-

ue models without notice.

Huck Installation Equipment should be serviced by

trained service technicians only.

Always give the Serial Number of the equipment

when corresponding or ordering service parts.

Complete repair facilities are maintained by Huck

International, Inc. Please contact one of the offices

listed below.

Eastern

One Corporate Drive Kingston, New York 12401-0250

Telephone (845) 331-7300 FAX (845) 334-7333

Outside USA and Canada

Contact your nearest Huck International Office, see

back cover.

In addition to the above repair facilities, there are

Authorized Tool Service Centers (ATSC's) located

throughout the United States. These service centers

offer repair services, spare parts, Service Parts Kits,

Service Tools Kits and Nose Assemblies. Please con-

tact your Huck Representative or the nearest Huck

office listed on the back cover for the ATSC in your

area.

Americas

Alcoa Fastening SystemsAerospace ProductsTucson Operations3724 East ColumbiaTucson, AZ 85714800‐234‐4825520‐747‐9898FAX: 520‐748‐2142

Alcoa Fastening SystemsAerospace ProductsCarson OperationsPO Box 5268900 Watson Center Rd.Carson, CA 90749800‐421‐1459310‐830‐8200FAX: 310‐830‐1436

Alcoa Fastening SystemsIndustrial ProductsWaco OperationsPO Box 81178001 Imperial DriveWaco, TX 76714‐8117800‐388‐4825254‐776‐2000FAX: 254‐751‐5259

Alcoa Fastening SystemsIndustrial ProductsKingston Operations1 Corporate DriveKingston, NY 12401800‐278‐4825845‐331‐7300FAX: 845‐334‐7333

Alcoa Fastening SystemsIndustrial ProductsLatin America OperationsAvenida Parque Lira. 79‐402Tacubaya Mexico, D.F.C.P. 11850FAX: 525‐515‐1776TELEX: 1173530 LUKSME

Far East

Alcoa Fastening SystemsIndustrial ProductsAustralia Operations14 Viewtech PlaceRowville, Victoria Australia 317803‐764‐5500Toll Free: 008‐335‐030FAX: 03‐764‐5510

Europe

Alcoa Fastening SystemsIndustrial ProductsUnited Kingdom OperationsUnit C, Stafford Park 7Telford, ShropshireEngland TF3 3BQ01952‐290011FAX: 0952‐290459

Alcoa Fastening SystemsAerospace ProductsFrance OperationsClos D’AssevilleBP495450 Us Par VignyFrance33‐1‐30‐27‐9500FAX: 33‐1‐34‐66‐0600

A Global Organization

Alcoa Fastening Systems (AFS) maintainscompany offices throughout the United Statesand Canada, with subsidiary offices in manyother countries. Authorized AFS distributorsare also located in many of the world’s

Industrial and Aerospace centers, where theyprovide a ready source of AFS fasteners,installation tools, tool parts, and applicationassistance.

For The Long Haul, The Future of FasteningTechnology, The Future of Assembly Technology,The Future of Tooling Technology, and Tools ofProductivity are service marks of HuckInternational. Huck provides technical assistanceregarding the use and application of Huck fasten‐ers and tooling.NOTICE: The information contained in this publi‐cation is only for general guidance with regard toproperties of the products shown and/or the

means for selecting such products, and is notintended to create any warranty, express,implied, or statutory; all warranties are containedonly in Huck’s written quotations, acknowledge‐ments, and/or purchase orders. It is recommend‐ed that the user secure specific, up‐to‐date dataand information regarding each applicationand/or use of such products.HWB898 1003‐5M

© 2003 Alcoa Fastening Systems1 Corporate Drive, Kingston, NY 12401 • Tel: 800‐431‐3091 • Fax: 845‐334‐7333 • www.alcoafasteningsystems.com

��

��

��

��

One Great ConnectionSM

Alcoa Fastening Systems world-wide locations:

For the Long Haul™

Documents

INSTRUCTION MANUAL MODELS 968 & 968D - Huck Toolshuck-tools.com/assets/images/huck-968-manual.pdf · 2015-12-10 · Description of Machinery: ... should be done by a qualified repairman