Interoperability Report · Ascom i62 – Cisco WLC 16-April-2019 8 / 24 Appendix A: Validation Configurations Cisco WLC platform Version 8.9.100 In the following chapter you will

Interoperability Report

Ascom i62

Cisco WLC

WLC controller platform

Cisco WLC v. 8.9.100

Ascom i62 v. 6.1.0

Morrisville, NC, USA

April 2019

Interoperability Report Date Page Ascom i62 – Cisco WLC 16-April-2019 2 / 24

Contents

Introduction ...................................................................................................................................... 3

About Ascom .................................................................................................................................. 3

About Cisco .................................................................................................................................... 3

Site Information ............................................................................................................................... 4

Verification site ............................................................................................................................... 4

Participants .................................................................................................................................... 4

Verification topology ....................................................................................................................... 4

Summary .......................................................................................................................................... 5

General conclusions ....................................................................................................................... 5

Verification overview ...................................................................................................................... 6

Known limitations ........................................................................................................................... 7

Appendix A: Validation Configurations ......................................................................................... 8

Cisco WLC platform Version 8.9.100 ............................................................................................. 8

Ascom i62 .................................................................................................................................... 21

Appendix B: Interoperability Validation Records ....................................................................... 24

Document History .......................................................................................................................... 24


Introduction

This document describes a summary of the interoperability verification results of the Ascom’s and Cisco’s

platform, necessary steps and guidelines to optimally configure the platforms and support contact details. The

report should be used in conjunction with both Cisco’s and Ascom’s platform configuration guides.

About Ascom

Ascom is a global solutions provider focused on healthcare ICT and mobile workflow solutions. The vision of

Ascom is to close digital information gaps allowing for the best possible decisions – anytime and anywhere.

Ascom’s mission is to provide mission-critical, real-time solutions for highly mobile, ad hoc, and time-sensitive

environments. Ascom uses its unique product and solutions portfolio and software architecture capabilities to

devise integration and mobilization solutions that provide truly smooth, complete and efficient workflows for

healthcare as well as for industry, security and retail sectors.

Ascom is headquartered in Baar (Switzerland), has subsidiaries in 15 countries and employs around 1,300 people

worldwide. Ascom registered shares (ASCN) are listed on the SIX Swiss Exchange in Zurich.

About Cisco

Cisco (NASDAQ: CSCO) is the worldwide technology leader that has been making the Internet work since 1984.

Our people, products and partners help society securely connect and seize tomorrow's digital opportunity today.

Discover more at thenetwork.cisco.com and follow us on Twitter at @Cisco.


Site Information

Verification site Ascom US

300 Perimeter park drive

Morrisville, NC, US-27560

USA

Participants

Karl-Magnus Olsson, Ascom, Morrisville

Verification topology


Summary

General conclusions The Ascom interoperability verification produced very good results with regards to authentication, stability and

roaming.

A full validation test was performed towards AP 9115 and 9117. A less extensive regression test has been

performed towards the already certified AP models AP 3702, 3802, 1852, 4800.

Compatibility information

One Access point model from every product generation has been selected as a representation (3702, 3802, 1852,

4800, 9115 and 9117). By testing these access points we are considered cover all supported major Cisco access

points based on chipset compatibility listed below.

Supported Partner Access Points with SW version 8.9.100:

AP1702, 2702, 3702

AP1832, 1852

AP2802, 3802

AP 4800

AP 9115, 9117

Supported Partner Controller Platforms with SW version 8.9.100:

Cisco 3504 Wireless Controller



Cisco Virtual Wireless Controller (vWLC)

Cisco Wireless Controllers for High Availability for Cisco 3504 WLC, Cisco 5520 WLC, and Cisco 8540 WLC.

Cisco Mobility Express Solution


Verification overview

WLAN Compatibility and Performance

High Level Functionality Result Comments

Association, Open with No Encryption OK

Association, WPA2-PSK / AES Encryption OK

Association, PEAP-MSCHAPv2 Auth, AES Encryption OK

Association with EAP-TLS authentication OK

Association, Multiple ESSIDs OK

Beacon Interval and DTIM Period OK

PMKSA Caching OK

WPA2-opportunistic/proactive Key Caching OK

WMM Prioritization OK

802.11 Power-save mode OK

802.11e U-APSD OK

802.11e U-APSD (load test) OK

Roaming, WPA2-PSK, AES Encryption OK * Typical roaming time 55 ms

Roaming, PEAP-MSCHAPv2 Auth, AES Encryption OK ** Typical roaming time 40 ms

Roaming, EAP-FAST, CCKM OK Typical roaming time 30 ms

*) Average roaming times are measured using 802.11a/n. Refer to Appendix B for detailed test results

* *) Measured times is with opportunistic/proactive Key Caching enabled (default enabled)


Known limitations

Description and Consequence Workaround Ticket(s)

raised

No known issues

For additional information regarding the known limitations please contact [email protected] or [email protected].

For detailed verification results, refer to Appendix B: Interoperability Validation Records.

mailto:[email protected]:[email protected]


Appendix A: Validation Configurations

Cisco WLC platform Version 8.9.100

In the following chapter you will find screenshots and explanations of basic settings in order to get a Cisco WLC

WLAN system to operate with an Ascom i62. Please note that security settings were modified according to

requirements in individual test cases.

Security settings (PSK)

Example of how to configure the system for PSK (WPA2-AES)

Security profile WPA2-PSK, AES encryption

- Select WPA2 Policy with AES encryption. - Select PSK and enter a key (Here in ASCII format)


802.1X authentication (PEAP-MSCHAPv2).

Example of how to configure the system for .1X authentication

Configuration of authentication using external Radius server, 802.1X (Step 1). In this example is WPA2-AES

used. Select 802.1X as Authentication Key Management.

Note. Ascom i62 can operate on a SSID that has both 802.1X and FT 802.1X enabled.

Note. To use CCKM, replace 802.1X with CCKM check box. The “security mode” in the i62 has to be set to

“Advanced” and CCKM has to be selected as “Authentication Key Management” instead of the default

802.1X.


Example of authentication configuration using external Radius server (Step 2). Select the server to use. The

server is configured under tab Security/Radius. See configuration of server below.


Configuration of authentication using external Radius server (Step 3). The IP address and the secret must

correspond to the IP and the credential used by the Radius server. Tests were performed using FreeRadius as

RADIUS server.

Note. Depending on authentication method used it might be necessary to add a certificate into the i62.

PEAP-MSCHAPv2 requires a CA certificate and EAP-TLS requires both a CA certificate and a client

certificate. Server certificate validation can be overridden in version 4.1.12 and above per handset setting.

Note. Refer to the i62 section in for matching handset configurations.


EAP-FAST using an internal authentication server.

Configuration of authentication using internal Radius server and EAP-FAST (Step 1). In this example is WPA2-

AES/CCMP used.

Note. To use CCKM, replace 802.1X with CCKM check box. The “security mode” in the i62 has to be set to

“Advanced” and CCKM has to be selected as “Authentication Key Management” instead of the default

802.1X.


Configuration of authentication using internal Radius server and EAP-FAST (Step 2). Check the box “Local EAP

Authentication” and choose your local EAP profile (created in step 4).

Note. Local EAP used for test purpose as external RADIUS don’t support EAP-FAST.

Configuration of authentication using internal Radius server and EAP-FAST (Step 3). Create a local user and

assign a password.


Configuration of authentication using internal Radius server and EAP-FAST (Step 4). Create a local EAP profile

and choose the EAP method to use.


General settings (QoS, Radio)

Set QoS to “Platinum (Voice)”

Make sure that WMM policy is set to “Required” or “Allowed”


Make sure “Session timeout” is disabled. Coverage Hole Detection can be left enabled if RRM is used in the

system. Set DTIM period to Ascom recommended value 5. DTIM value 5 values are recommended in order to

allow maximum battery conservation without impacting the quality. Using a lower DTIM value is possible but will

reduce the standby time.

Make sure Client Load Balancing and Client Band select is disabled.

Even though 11k features are not supported Ascom i62 it can coexist in a network were it is enabled.


Channel configuration. See next picture for additional information.

Ascom recommended settings for 802.11b/g/n are to only use channel 1, 6 and 11. For 802.11a/n/ac use

channels according to the infrastructure manufacturer, country regulations and per guidelines below.

Note that Tx power level and channel was manually set for test purpose.

General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments:

1. Enabling more than 8 channels will degrade roaming performance. In situations where UNII1 and UNII3 are used, a maximum of 9 enabled channels can be allowed.

Ascom does not recommend exceeding this limit.

2. Using 40 MHz channels (or “channel-bonding”) will reduce the number of non-DFS* channels to two in ETSI regions (Europe). In FCC regions (North America), 20MHz is a more viable option because of the availability of additional non-DFS channels. The handset can co-exist with 40MHz stations in the same ESS.

3. Ascom do support and can coexist in 80MHz channel bonding environments. The recommendations is however to avoid 80MHz channel bonding as it severely reduces the number of available non overlapping channels.

4. Make sure that all non-DFS channel are taken before resorting to DFS channels. The handset can cope in mixed non-DFS and DFS environments; however, due to “unpredictability” introduced by radar detection protocols, voice quality may become distorted and roaming delayed. Hence Ascom recommends if possible avoiding the use of DFS channels in VoWIFI deployments.

*) Dynamic Frequency Selection (radar detection)


The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have

12Mbps as lowest supported speed.

As Ascom i62 do support Channel Switch Announcement it’s recommended to have this setting enabled in the

system (only applicable when DFS channels are used)


Ascom i62 is an .11n device but can coexist in .11ac and 11ax systems with both 40 MHz and 80 MHz channel

width. We recommend disabling the lowest data rates including MCS0

Follow the recommendations “General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac

environments“ on Page 16

The default data rate set will work fine, however for optimization Ascom recommends disabling the lowest data

rates and have 12Mbps as lowest mandatory rate.


Ascom recommends “EDCA Profile”: Voice Optimized

Make sure Low Latency MAC is disabled. (Both 802.11a/n/ac and 802.11b/g/n)

Note. Using EDCA Profile “WMM” is acceptable but “Voice Optimized” is to prefer when voice clients are

present in the system.

Depending on the infrastructure (switches) ”Protocol Type” may have to be disabled.


Ascom i62

Network settings for WPA2-PSK

Note. Make sure that the enabled channels in the i62 handset match the channel plan used in the system.

Note. FCC is no longer allowing 802.11d to determine regulatory domain. Devices deployed in USA must

set Regulatory domain to “USA”.


Network settings for .1X authentication (PEAP-MSCHAPv2)


802.1X Authentication requires a CA certificate to be uploaded to the phone by “right clicking” - > Edit certificates.

EAP-TLS will require both a CA and a client certificate.

Note that both a CA and a client certificate are needed for TLS. Otherwise only a CA certificate is needed.

Server certificate validation can be overridden in version 4.1.12 and above per handset setting.


Appendix B: Interoperability Validation Records

Pass

Fail

Comments

Not verified

19

0

1

4

Total 24

Refer to the attached file for detailed verification results.

Refer to the verification specification for explicit information regarding each verification case.

The specification can be found here (requires login):

https://www.ascom-ws.com/AscomPartnerWeb/en/startpage/Sales-tools/Interoperability/Templates/

Document History

Rev Date Author Description

P1 16-April-19 SEKMO Draft

R1 29-April-19 SEKMO Minor alterations after review.

https://www.ascom-ws.com/AscomPartnerWeb/en/startpage/Sales-tools/Interoperability/Templates/

i62

WLAN Interoperability Test ReportWLAN configuration:

Beacon Interval: 100ms

Test object - Handset:DTIM Interval: 5

Ascom i62 version 6.1.0802.11d Regulatory Domain: World

Test object - WLAN system:WMM Enabled (Auto/WMM)

Cisco WLC 3504 Version 8.9.100No Auto-tune

AP 1850, 3700, 3800, 4800, 9115 and 9117AP3702AP3800AP4800AP9115AP9117Single Voice VLAN

2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz

Test CaseDescriptionVerdictVerdictVerdictVerdictVerdictVerdictVerdictVerdictVerdictVerdictComment

TEST AREA ASSOCIATION / AUTHENTICATION

#101Association with open authentication, no encryptionNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#107Association with WPA2-PSK authentication, AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSHidden SSID validated.

#110Association with PEAP-MSCHAPv2 auth, AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSFreeRADIUS server; RootCA loaded to device;FAIL

#111Association with EAP-FAST authenticationPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSWLC internal authtication server

#116Association with EAP-TLS authenticationPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSFreeRADIUS server; Root CA and client cert loaded to device;

TEST AREA POWER-SAVE AND QOSPASS

#150802.11 Power-save modePASSPASSPASSPASSPASSPASSPASSPASSPASSPASSFAIL

#151Beacon period and DTIM intervalNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDPASSPASSPASSPASSBeacon period 100tu, DTIM 1,2,5 verifiedNOT TESTED

#152802.11e U-APSDPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSSee Comment

#202WMM prioritizationPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSIperf for load generation of unprioritized data.

TEST AREA "PERFORMANCE"

#308Power-save mode U-APSD – WPA2-PSKNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#310CAC - TSPECNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDPASSPASSPASSPASS

TEST AREA ROAMING AND HANDOVER TIMES

#401Handover with open authentication and no encryptionNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#404Handover with WPA2-PSK auth and AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSAVG roaming time 11an:55 ms, bgn: 61 ms (No significant difference seen in roaming times between different AP models)

#408Handover with PEAP-MSCHAPv2 authentication and AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSAVG roaming time 11an: 40ms, bgn: 42 ms (No significant difference seen in roaming times between different AP models).

#411Handover using PMKSA and opportunistic/proactive key cachingPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSOKC enabled by default. Same test case as #408

#409EAP-FAST CCKMPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSAVG roaming time an: 30 ms, gn: 37ms (No significant difference seen in roaming times between different AP models).

TEST AREA BATTERY LIFETIME

#501Battery lifetime in idleNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDPASSPASSPASSPASS80h+ in idle. Good signal strength

#504Battery lifetime in call with power save mode U-APSDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDPASSPASSPASSPASS12h+ in call. Default settings and non-DFS channels only

TEST AREA STABILITY

#602Duration of call – U-APSD modeNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDPASSPASSPASSPASS>1hrs stable call without interruption

TEST AREA 802.11n

#801Frame aggregation A-MSDUSee CommentSee CommentSee CommentSee CommentSee CommentSee CommentSee CommentSee CommentSee CommentSee CommentNo frame aggregation in UP6 by default settings.

#802Frame aggregation A-MPDUNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#80440Mhz channelsNOT TESTEDPASSNOT TESTEDPASSNOT TESTEDPASSNOT TESTEDPASSNOT TESTEDPASS

#805802.11n ratesPASSPASSPASSPASSPASSPASSPASSPASSPASSPASSOK

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.04.16 14:35:22 =~=~=~=~=~=~=~=~=~=~=~=show running-config

Notice: "show running-config" has been changed to be an alias to "show run-config".Use "show run-config commands" to display the configuration commands.Press Enter to continue or to abort...

System Inventory

NAME: "Chassis" , DESCR: "Cisco 3500 Series Wireless LAN Controller"

PID: AIR-CT3504-K9, VID: V01, SN: FCW2146M04P

Burned-in MAC Address............................ 6C:DD:30:4A:92:80Maximum number of APs supported.................. 150Press Enter to continue or to abort

System InformationManufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco ControllerProduct Version.................................. 8.9.100.0RTOS Version..................................... 8.9.100.0Bootloader Version............................... 8.5.103.0Emergency Image Version.......................... 8.5.103.0

OUI File Last Update Time........................ N/ABuild Type....................................... DATA + WPS

System Name...................................... 3504oneSystem Location.................................. System Contact................................... System ObjectID.................................. 1.3.6.1.4.1.9.1.2427Redundancy Mode.................................. DisabledIP Address....................................... 172.20.94.15IPv6 Address..................................... ::Last Reset....................................... Soft reset due to RST_SOFT_RST write System Up Time................................... 0 days 22 hrs 55 mins 41 secsSystem Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)System Stats Realtime Interval................... 5

--More or (q)uit current module or to abortSystem Stats Normal Interval..................... 180

Configured Country............................... Multiple Countries : SE,USOperating Environment............................ Commercial (10 to 35 C)Internal Temp Alarm Limits....................... -10 to 80 CInternal Temperature............................. +67 CMgig Temp Alarm Limits........................... -10 to 78 CMgig Temperature................................. +51 CExternal Temp Alarm Limits....................... -10 to 71 CExternal Temperature............................. +43 CFan Status....................................... OKFan Speed Mode................................... Disable

State of 802.11b Network......................... EnabledState of 802.11a Network......................... EnabledNumber of WLANs.................................. 7Number of Active Clients......................... 10

OUI Classification Failure Count................. 324

Memory Current Usage............................. 32Memory Average Usage............................. 32CPU Current Usage................................ 0

--More or (q)uit current module or to abortCPU Average Usage................................ 0

Flash Type....................................... Compact Flash Card

Flash Size....................................... 1073741824

Burned-in MAC Address............................ 6C:DD:30:4A:92:80Maximum number of APs supported.................. 150System Nas-Id.................................... WLC MIC Certificate Types........................ SHA1/SHA2Licensing Type................................... RTU

USB ........................................... enabled

Press Enter to continue or to abort

Backup Controller Configuration

AP primary Backup Controller .................... AP secondary Backup Controller .................. Press Enter to continue or to abort

System Time Information:

Time............................................. Tue Apr 16 08:40:09 2019

Timezone delta................................... 0:0Timezone location................................ (GMT -5:00) Eastern Time (US and Canada)

NTP Servers NTP Version.................................. 3 NTP Polling Interval......................... 86400

Index NTP Key Index NTP Server Status NTP Msg Auth Status ------- --------------------------------------------------------------------- 1 0 192.168.0.12 Not Synched AUTH DISABLED

Press Enter to continue or to abort

Redundancy InformationRedundancy Mode ................................. SSO DISABLED

Local State...................................... ACTIVEPeer State....................................... N/A

Unit............................................. Primary

Unit ID.......................................... 6C:DD:30:4A:92:80

Redunadancy State................................ N/A

Mobility MAC..................................... 6C:DD:30:4A:92:80

Link Encryption.................................. ENABLED

Redundancy Management IP Address................. 0.0.0.0Peer Redundancy Management IP Address............ 0.0.0.0Redundancy Port IP Address....................... 0.0.0.0Peer Redundancy Port IP Address.................. 169.254.0.0Press Enter to continue or to abort

AP Bundle Information

Primary AP ImageSizeSupported AP's --------------------------------ap1g113320AP700ap1g315372AP1530ap1g429180AP1850/1810ap1g531316AP1815,1540,AP1840ap1g631520AP2900,C9117ap1g745612AP1900,C9115ap3g340544AP2800,3800,4800,1560c157013040AP1570c370014360AP1700,2700,3700

Secondary AP ImageSizeSupported AP's ----------------------------------ap1g113320AP700ap1g315372AP1530ap1g429180AP1850/1810ap1g531320AP1815,1540,AP1840ap1g631520AP2900,C9117ap1g745636AP1900,C9115

--More or (q)uit current module or to abortap3g340540AP2800,3800,4800,1560c157013040AP1570c370014360AP1700,2700,3700Press Enter to continue or to abort

Switch Configuration802.3x Flow Control Mode......................... Disable FIPS prerequisite features....................... DisabledWLANCC prerequisite features..................... DisabledUCAPL prerequisite features...................... DisabledLast login information display................... DisabledDTLS WLC MIC .................................... SHA2secret obfuscation............................... EnabledStrong Password Check Features case-check.................................... Enabled consecutive-check............................. Enabled default-check................................. Enabled username-check................................ Enabled position-check................................ Enabled case-digit-check.............................. Enabled Min. Password length.......................... 8 Min. Upper case chars......................... 0 Min. Lower case chars......................... 0 Min. Digits chars............................. 0 Min. Special chars............................ 0Mgmt User Password Lifetime [days]...................... 0

--More or (q)uit current module or to abort Password Lockout.............................. Disabled Lockout Attempts.............................. 3 Lockout Timeout [mins]........................ 5SNMPv3 User Password Lifetime [days]...................... 0 Password Lockout.............................. Disabled Lockout Attempts.............................. 3 Lockout Timeout [mins]........................ 5Press Enter to continue or to abort

Network InformationRF-Network Name............................. ascomDNS Server IP............................... 0.0.0.0Web Mode.................................... DisableSecure Web Mode............................. EnableSecure Web Mode Cipher-Option High.......... DisableSecure Web Mode SSL Protocol................ DisableWeb CSRF check.............................. EnableOCSP........................................ DisabledOCSP responder URL.......................... Secure Shell (ssh).......................... EnableSecure Shell (ssh) Cipher-Option High....... DisableTelnet...................................... DisableEthernet Multicast Forwarding............... DisableEthernet Broadcast Forwarding............... DisableIPv4 AP Multicast/Broadcast Mode............ UnicastIPv6 AP Multicast/Broadcast Mode............ UnicastIGMP snooping............................... DisabledIGMP timeout................................ 60 secondsIGMP Query Interval......................... 20 secondsMLD snooping................................ DisabledMLD timeout................................. 60 seconds

--More or (q)uit current module or to abortMLD query interval.......................... 20 secondsUser Idle Timeout........................... 300 secondsARP Idle Timeout............................ 300 secondsCisco AP Default Master..................... DisableAP Join Priority............................ DisableMgmt Via Wireless Interface................. DisableMgmt Via Dynamic Interface.................. DisableBridge MAC filter Config.................... EnableBridge Security Mode........................ EAPMesh Full Sector DFS........................ EnableMesh Backhaul RRM........................... DisableAP Fallback ................................ EnableAP EasyAdmin ............................... DisableAP Virtual IP .............................. 10.1.0.6Web Auth CMCC Support ...................... DisabledWeb Auth Redirect Ports .................... 80Web Auth Proxy Redirect ................... DisableWeb Auth Captive-Bypass .................. DisableWeb Auth Secure Web ....................... EnableWeb Auth Secure Web Cipher Option ......... DisableWeb Auth Secure Web Sslv3 ................. DisableWeb Auth Secure Redirection ............... DisableFast SSID Change ........................... Enabled

--More or (q)uit current module or to abortAP Discovery - NAT IP Only ................. EnabledIP/MAC Addr Binding Check .................. EnabledLink Local Bridging Status ................. DisabledCCX-lite status ............................ Disableoeap-600 dual-rlan-ports ................... Disableoeap local-network ......................... Enableoeap-600 Split Tunneling (Printers)......... DisableWebPortal Online Client .................... 0WebPortal NTF_LOGOUT Client ................ 0mDNS snooping............................... DisabledmDNS Query Interval......................... 15 minutesWeb Color Theme............................. DefaultCapwap Prefer Mode.......................... IPv4Network Profile............................. DisabledClient ip conflict detection (DHCP) ........ DisabledMesh BH RRM ................................ DisableMesh Aggressive DCA......................... DisableMesh Auto RF................................ DisableHTTP Profiling Port......................... 80HTTP-Proxy Ip Address....................... 0.0.0.0HTTP-Proxy Port............................. 80WGB Client Forced L2 Roam................... DisabledPress Enter to continue or to abort

Port Summary STP Admin Physical Physical Link LinkPr Type Stat Mode Mode Status Status Trap POE -- ------- ---- ------- ---------- ---------- ------ ------- ---------1 Normal Forw Enable Auto 100 Full Up Enable N/A 2 Normal Disa Enable Auto Auto Down Enable N/A 3 Normal Forw Enable Auto 100 Full Up Enable Enable (Power Off) 4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off) 5 Normal Disa Enable Auto Auto Down Enable N/A RP Normal Disa Enable Auto Auto Down Enable N/A SP Normal Disa Enable Auto Auto Down Enable N/A Press Enter to continue or to abort

AP SummaryNumber of APs.................................... 2

Global AP User Name.............................. adminGlobal AP Dot1x User Name........................ Not ConfiguredGlobal AP Dot1x EAP Method....................... EAP-FAST

AP Name Slots AP Model Ethernet MAC Location Country IP Address Clients DSE Location ------------------------------ ----- -------------------- ----------------- -------------------- ---------- --------------- ------- --------------AP00A6.CA36.210E 3 AIR-AP3802I-B-K9 00:a6:ca:36:21:0e default location US 172.20.94.77 0 [0 ,0 ,0 ]AP7069.5A74.7EC8 2 C9115AXE-B 70:69:5a:74:7e:c8 default location US 172.20.94.64 10 [0 ,0 ,0 ]

AP Tcp-Mss-Adjust InfoAP Name TCP State MSS Size------------------ -------- ------- AP00A6.CA36.210E enabled 1250 AP7069.5A74.7EC8 enabled 1250 Press Enter to continue or to abort

AP LocationTotal Number of AP Groups........................ 1

Site Name........................................ default-groupSite Description................................. NAS-identifier................................... noneClient Traffic QinQ Enable....................... FALSEDHCPv4 QinQ Enable............................... FALSEAP Operating Class............................... Not-configuredCapwap Prefer Mode............................... Not-configuredAntenna Monitoring - Status...................... DisabledCustomWeb Global Status.......................... EnabledExternal Web Authentication URL..................

RF Profile----------2.4 GHz band..................................... 5 GHz band.......................................

WLAN ID Interface Network Admission Control Radio Policy OpenDnsProfile------- ----------- -------------------------- ------------ -------------- 1 management Disabled None None

--More or (q)uit current module or to abort 2 management Disabled None None 3 management Disabled None None 4 management Disabled None None 5 management Disabled None None 6 management Disabled None None 7 management Disabled None None

*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.

Lan Port configs ----------------

LAN Status POE RLAN--- ------- ---- ----- 1 Disabled Disabled None 2 Disabled None 3 Disabled None

External Module configs -----------------------------

LAN Status POE RLAN

--More or (q)uit current module or to abort--- ------- ---- ----- 1 Disabled None

USB Module configs -----------------------------USB Module Status................................ Enabled

AP Name Slots AP Model Ethernet MAC Location Port Country Priority------------------ ----- ------------------- ----------------- ---------------- ---- ------- --------AP00A6.CA36.210E 3 AIR-AP3802I-B-K9 00:a6:ca:36:21:0e default location 3 US 1AP7069.5A74.7EC8 2 C9115AXE-B 70:69:5a:74:7e:c8 default location 3 US 1

Fabric Flex Acl Template Name ................... Not ConfiguredPress Enter to continue or to abort

RF Profile

Number of RF Profiles............................ 6

Out Of Box State................................. Disabled

Out Of Box Persistence........................... Disabled

RF Profile Name Band Description 11n-client-only Applied --------------------------------- ------- ----------------------------------- ------------------ ----------High-Client-Density-802.11a 5 GHz disable No High-Client-Density-802.11bg 2.4 GHz disable No Low-Client-Density-802.11a 5 GHz disable No Low-Client-Density-802.11bg 2.4 GHz disable No Typical-Client-Density-802.11a 5 GHz disable No Typical-Client-Density-802.11bg 2.4 GHz disable No

RF Profile name................................ High-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz

--More or (q)uit current module or to abort11n-client-only.................................. disabledTransmit Power Threshold v1...................... -65 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... 7 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Mandatory 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

--More or (q)uit current module or to abort

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -78 dBmCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

Client Aware FRA State........................................ Disabled Client Select Utilization Threshold.......... 50% Client Reset Utilization Threshold........... 5%

Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds

--More or (q)uit current module or to abort Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm

Load Balancing Denial....................................... 3 count Window....................................... 5 clients

Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 36,40,44,48,52,56,60,64,100, 104,108,112,116,120,124,128, 132,136,140,149,153,157,161DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabledHSR Mode......................................... disabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ High-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... 7 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Disabled

--More or (q)uit current module or to abort 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Mandatory 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 %

--More or (q)uit current module or to abort Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -82 dBmCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled


Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm

Load Balancing Denial....................................... 3 count

--More or (q)uit current module or to abort Window....................................... 5 clients

Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabledHSR Mode......................................... disabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default


RF Profile name................................ Low-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -60 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Mandatory 802.11a 9M Rate.............................. Supported 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Mandatory 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------


1 600

2 600

3 600

4 600

5 600

6 600

7 600



--More or (q)uit current module or to abortBand Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm


Coverage Data Data......................................... -90 dBm Voice........................................ -90 dBm Minimum Client Level......................... 2 clients Exception Level.............................. 25 %DCA Channel List................................. 36,40,44,48,52,56,60,64,100, 104,108,112,116,120,124,128, 132,136,140,149,153,157,161DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

--More or (q)uit current module or to abortHSR Mode......................................... disabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Low-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -65 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm

--More or (q)uit current module or to abort802.11b/g Operational Rates 802.11b/g 1M Rate............................ Mandatory 802.11b/g 2M Rate............................ Mandatory 802.11b/g 5.5M Rate.......................... Mandatory 802.11b/g 11M Rate........................... Mandatory 802.11g 6M Rate.............................. Supported 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Supported 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600


7 600



Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds

--More or (q)uit current module or to abort Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm



802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled


--More or (q)uit current module or to abort MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Typical-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Mandatory 802.11a 9M Rate.............................. Supported 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Mandatory 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported

--More or (q)uit current module or to abort 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. AUTOCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

--More or (q)uit current module or to abortClient Aware FRA State........................................ Disabled Client Select Utilization Threshold.......... 50% Client Reset Utilization Threshold........... 5%

Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm


Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %

--More or (q)uit current module or to abortDCA Channel List................................. 36,40,44,48,52,56,60,64,100, 104,108,112,116,120,124,128, 132,136,140,149,153,157,161DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabledHSR Mode......................................... disabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Typical-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz

--More or (q)uit current module or to abort11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Disabled 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Mandatory 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600


2 600

3 600

4 600

5 600

6 600

7 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. AUTOCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled


Band Select

--More or (q)uit current module or to abort Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm



802.11n MCS Rates


--More or (q)uit current module or to abort MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... defaultPress Enter to continue or to abort

AP ConfigCisco AP Identifier.............................. 4Cisco AP Name.................................... AP00A6.CA36.210ECountry code..................................... Multiple Countries : SE,USRegulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-ABEAP Country code.................................. US - United StatesAP Regulatory Domain............................. -BSwitch Port Number .............................. 3MAC Address...................................... 00:a6:ca:36:21:0eIP Address Configuration......................... DHCPIP Address....................................... 172.20.94.77IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 172.20.96.2NAT External IP Address.......................... NoneCAPWAP Path MTU.................................. 1485DHCP Release Override............................ Disabled Telnet State..................................... Globally DisabledSsh State........................................ Globally EnabledNSI Ports State.................................. Globally EnabledCisco AP Location................................ default locationCisco AP Floor Label............................. 0Cisco AP Group Name.............................. default-group

--More or (q)uit current module or to abortPrimary Cisco Switch Name........................ 3504onePrimary Cisco Switch IP Address.................. 192.168.0.60Secondary Cisco Switch Name...................... Cisco_fa:75:a4Secondary Cisco Switch IP Address................ 192.168.0.15Tertiary Cisco Switch Name....................... Tertiary Cisco Switch IP Address................. Not ConfiguredAdministrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalPublic Safety ................................... Disabled AP SubMode ...................................... Not ConfiguredRogue Detection ................................. EnabledRemote AP Debug ................................. DisabledLogging trap severity level ..................... errorsLogging syslog facility ......................... kernS/W Version .................................... 8.9.100.0Boot Version ................................... 1.1.2.4Mini IOS Version ................................ 0.0.0.0Stats Reporting Period .......................... 30Stats Collection Mode ........................... normalRadio Core Mode ................................. NormalSlub Debug Mode ................................. Disabled

--More or (q)uit current module or to abortStatic Ip Failover .............................. EnabledLED State........................................ EnabledPoE Pre-Standard Switch.......................... DisabledPoE Power Injector MAC Addr...................... DisabledPower Type/Mode.................................. PoE/Full PowerNumber Of Slots.................................. 3 AP Model......................................... AIR-AP3802I-B-K9AP Image......................................... AP3G3-K9W8-MIOS Version...................................... 8.9.100.0Reset Button..................................... EnabledAP Serial Number................................. FCW2038N72UAP Certificate Type.............................. Manufacture InstalledAP Lag Status ................................... DisableAP User Mode..................................... AUTOMATICAP User Name..................................... adminAP Dot1x User Mode............................... Not ConfiguredAP Dot1x User Name............................... Not ConfiguredCisco AP system logging host..................... 255.255.255.255AP Core Dump Config.............................. DisabledAP Up Time....................................... 0 days, 22 h 53 m 10 sAP LWAPP Up Time................................. 0 days, 22 h 50 m 46 sJoin Date and Time............................... Mon Apr 15 09:49:26 2019Join Taken Time.................................. 0 days, 00 h 02 m 23 s


Attributes for Slot 0 Radio Type................................... RADIO_TYPE_80211n-DualBand Radio Subtype................................ TX and RX Radio Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP Mesh Radio Role ............................. ACCESS Radio Role .................................. Client Serving (Local) Assignment Method.......................... Manual Band....................................... 2.4GHz CellId ...................................... 0

Station Configuration Configuration ............................. CUSTOMIZED Number Of WLANs ........................... 4 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... 00:6b:f1:55:18:20 Operation Rate Set 12000 Kilo Bits.......................... MANDATORY 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED

--More or (q)uit current module or to abort 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set MCS 0.................................... SUPPORTED MCS 1.................................... SUPPORTED MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED MCS 16................................... SUPPORTED MCS 17................................... SUPPORTED MCS 18................................... SUPPORTED

--More or (q)uit current module or to abort MCS 19................................... SUPPORTED MCS 20................................... SUPPORTED MCS 21................................... SUPPORTED MCS 22................................... SUPPORTED MCS 23................................... SUPPORTED MCS 24................................... DISABLED MCS 25................................... DISABLED MCS 26................................... DISABLED MCS 27................................... DISABLED MCS 28................................... DISABLED MCS 29................................... DISABLED MCS 30................................... DISABLED MCS 31................................... DISABLED 802.11ac MCS Set Nss=1: MCS 0-9 .......................... SUPPORTED Nss=2: MCS 0-9 .......................... SUPPORTED Nss=3: MCS 0-9 .......................... SUPPORTED Nss=4: MCS 0-7 .......................... SUPPORTED Beacon Period ............................. 100 Fragmentation Threshold ................... 0 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US


Multi Domain Capability Configuration ............................. CUSTOMIZED First Chan Num ............................ 0 Number Of Channels ........................ 0

MAC Operation Parameters Configuration ............................. CUSTOMIZED Fragmentation Threshold ................... 0 Packet Retry Limit ........................ 64

Tx Power Num Of Supported Power Levels ............. 8 Tx Power Level 1 .......................... 23 dBm Tx Power Level 2 .......................... 20 dBm Tx Power Level 3 .......................... 17 dBm Tx Power Level 4 .......................... 14 dBm Tx Power Level 5 .......................... 11 dBm Tx Power Level 6 .......................... 8 dBm Tx Power Level 7 .......................... 5 dBm Tx Power Level 8 .......................... 2 dBm Tx Power Configuration .................... CUSTOMIZED Current Tx Power Level .................... 6

--More or (q)uit current module or to abort Tx Power Assigned By ...................... User

Phy DSSS parameters Configuration ............................. CUSTOMIZED Current Channel ........................... 6 Channel Assigned By ....................... DCA Default Extension Channel ......................... NONE Channel Width.............................. 20MHz Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11 Current CCA Mode .......................... 0 ED Threshold .............................. -50 DCA Channel List........................... Global Legacy Tx Beamforming Configuration ....... AUTOMATIC Legacy Tx Beamforming ..................... DISABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 8 Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED D....................................... ENABLED

--More or (q)uit current module or to abort Performance Profile Parameters Configuration ............................. AUTOMATIC Interference threshold..................... 10 % Noise threshold............................ -70 dBm RF utilization threshold................... 80 % Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 12 dB Coverage exception level................... 25 % Client minimum exception level............. 3 clients Rogue Containment Information Containment Count............................ 0

CleanAir Management Information CleanAir Capable......................... Yes CleanAir Management Administration St.... Enabled CleanAir Management Operation State...... Up Rapid Update Mode........................ Off Spectrum Expert connection............... Enabled CleanAir NSI Key....................... 289B9C2252CDBB7D3751DDEFA53635D5 Spectrum Expert Connections counter.... 0 CleanAir Sensor State.................... Configured

--More or (q)uit current module or to abort Radio Extended Configurations Beacon period.............................. 100 milliseconds Beacon range............................... AUTO Multicast buffer........................... AUTO Multicast data-rate........................ AUTO RX SOP threshold........................... DEFAULT CCA threshold.............................. AUTO

Attributes for Slot 1 Radio Type................................... RADIO_TYPE_80211ac-5 Radio Subband................................ RADIO_SUBBAND_ALL Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP Mesh Radio Role ............................. ACCESS Radio Role .................................. Client Serving (Local) CellId ...................................... 0

Station Configuration Configuration ............................. CUSTOMIZED Number Of WLANs ........................... 7 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60

--More or (q)uit current module or to abort BSSID ..................................... 00:6b:f1:55:18:20 Operation Rate Set 12000 Kilo Bits.......................... MANDATORY 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set MCS 0.................................... DISABLED MCS 1.................................... SUPPORTED MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED

--More or (q)uit current module or to abort MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED MCS 16................................... SUPPORTED MCS 17................................... SUPPORTED MCS 18................................... SUPPORTED MCS 19................................... SUPPORTED MCS 20................................... SUPPORTED MCS 21................................... SUPPORTED MCS 22................................... SUPPORTED MCS 23................................... SUPPORTED MCS 24................................... DISABLED MCS 25................................... DISABLED MCS 26................................... DISABLED MCS 27................................... DISABLED MCS 28................................... DISABLED MCS 29................................... DISABLED MCS 30................................... DISABLED MCS 31................................... DISABLED 802.11ac MCS Set Nss=1: MCS 0-9 .......................... SUPPORTED Nss=2: MCS 0-9 .......................... SUPPORTED Nss=3: MCS 0-9 .......................... SUPPORTED Nss=4: MCS 0-7 .......................... SUPPORTED

--More or (q)uit current module or to abort Beacon Period ............................. 100 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US

Multi Domain Capability Configuration ............................. CUSTOMIZED First Chan Num ............................ 0 Number Of Channels ........................ 0

MAC Operation Parameters Configuration ............................. CUSTOMIZED Fragmentation Threshold ................... 2346 Packet Retry Limit ........................ 64

Tx Power Num Of Supported Power Levels ............. 8 Tx Power Level 1 .......................... 22 dBm Tx Power Level 2 .......................... 19 dBm Tx Power Level 3 .......................... 16 dBm Tx Power Level 4 .......................... 13 dBm Tx Power Level 5 .......................... 10 dBm

--More or (q)uit current module or to abort Tx Power Level 6 .......................... 7 dBm Tx Power Level 7 .......................... 4 dBm Tx Power Level 8 .......................... 2 dBm Tx Power Configuration .................... CUSTOMIZED Current Tx Power Level .................... 4 Tx Power Assigned By ...................... User

Phy OFDM parameters Configuration ............................. CUSTOMIZED Current Channel ........................... 36 Channel Assigned By ....................... User Extension Channel ......................... ABOVE Channel Width.............................. 40MHz Allowed Channel List....................... 36,40,44,48,52,56,60,64,100, ......................................... 104,108,112,116,120,124,128, ......................................... 132,136,140,144,149,153,157, ......................................... 161,165 TI Threshold .............................. -50 DCA Channel List........................... Global Legacy Tx Beamforming Configuration ....... AUTOMATIC Legacy Tx Beamforming ..................... DISABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 10

--More or (q)uit current module or to abort Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED D....................................... ENABLED

Performance Profile Parameters Configuration ............................. AUTOMATIC Interference threshold..................... 10 % Noise threshold............................ -70 dBm RF utilization threshold................... 80 % Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 16 dB Coverage exception level.....

Documents

Interoperability Report · Ascom i62 – Cisco WLC 16-April-2019 8 / 24 Appendix A: Validation Configurations Cisco WLC platform Version 8.9.100 In the following chapter you will