issued by United Kingdom Accreditation Service · 2021. 1. 13. · BS EN ISO 10855-1:2018 BS EN ISO 10855-3:2018 IMO MSC/Circ.860 EN 12079-1: 2006 withdrawn EN 12079-3: 2006 withdrawn

Assessment Manager: RH1 Page 1 of 24

Schedule of Accreditation issued by

United Kingdom Accreditation Service

2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

0003

Type A Inspection Body

Accredited to ISO/IEC 17020:2012

Lloyd's Register Verification Ltd

Issue No: 040 Issue date: 26 May 2021

Registered Office

71 Fenchurch Street

London

EC3M 4BS

Contact: Nigel Tijou

Tel: +44 (0)330 414 1466

E-Mail: [email protected]

Website: www.lr.org

Inspection performed at/from the above address only

Locations covered by the organisation and their relevant activities

Location details Activity Location code

Address - Birmingham 1 Trinity Park Bickenhill Lane Solihull West Midlands B37 7ES United Kingdom

Local contact – Nigel Tijou

Inspection Activities: Head Office Control of policy

A

0003


Accredited to

ISO/IEC 17020:2012


United Kingdom Accreditation Service 2 P ine Trees , Che r t sey Lane , S ta ines -upon -Thames , TW18 3HR, UK

Lloyd’s Register Verification Ltd


Inspection performed at/from main address only


DETAIL OF ACCREDITATION

Field of Inspection

Type and Range of

Inspection

Methods and Procedures

Essential

Requirements

Location Code

Minor, Intermediate and Major Pressure Systems

Preparation and Certifying Written Schemes of Examination In-service Inspection

Pressure Systems Safety Regulations 2000 LR procedure IMS03 series

SI2000 No 128

A

Boilers Pressure Vessels and Assemblies

Design verification and new construction inspection

LR procedures IMS03 series

A

Welding Procedures and Welder Qualification Tests

Verification and approval LR procedure IMS03 series

A

Lifting equipment including powered lifting appliances, manual lifting appliances and lifting accessories.

(excluding: Motor Vehicle Lifting Tables, Mobile Elevating Work Platforms, Tower Cranes, Telehandlers, Passenger and Goods Lifts)

In-service inspection The Lifting Operations and Lifting Equipment Regulations 1998 – SI2307 (LOLER)

Provision and Use of Work Equipment Regulations 1998 (PUWER) LR procedure IMS03 series

A

0003


Accredited to

ISO/IEC 17020:2012







Field of Inspection

Type and Range of

Inspection

Methods and Procedures

Essential

Requirements

Location Code

Transportable Pressure Receptacles (For non EU use)

Design verification and new construction inspection

BS EN 1964-1 BS EN 1975 BS 5045:Part 8:2000 AS1777:2005 BS 5045-3 ISO 9809-1 ISO 9809-2 ISO 9809-3 ISO 7866

A

END

0003


Accredited to

ISO/IEC 17020:2012







Accreditation for the purpose of UK Appointed/Approved Body Activity in accordance with UKCA Requirements and UKAS Publication GEN 5

Directive/Regulation Conformity Assessment procedure/Module/Article and / or Inspection

Category of products or individual products

Methods / Procedures Essential requirements: Product specification/ Properties / Standards

Location Code

The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment (Amendment) (EU Exit) Regulations 2020. The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment (Northern Ireland) Regulations 2010 (as amended).

PART 3 of the Approved Derogations & Transitional Provisions.

Periodic inspection Intermediate inspection. Exceptional checks to VCA procedures:

UK road, and rail, tanks* constructed before 10/05/04 and in NI before 31/07/06. Metallic tanks. Vacuum-operated waste tanks. for substances of Class(s) 2, 3, 4, 5, 6, 8 & 9

VCA Procedures for Inspection & Testing of UK Tanks IMS03 procedures for containers

A

Periodic inspection and intermediate inspection, exceptional checks 4.7.1 – 4.7.7 (EN12972)

UK Road tanks for LPG * constructed in GB after 10/05/04 or in NI after 31/07/06 to EN 12493, Annex C.

EN 12972:2018 IMS03 procedures for containers

A

Type Approval Supervision of construction Initial inspection and test

UK Road tanks for LPG * constructed in GB after 10/05/04 or in NI after 31/07/06 to EN 12493, Annex C.

EN 12972:2018 EN12493:2013 EN12493:2013+2014+2015 IMS03 procedures for containers

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code

RID, ADR and the IMDG Code Chapter 6.8 & 6.10

Periodic inspection & Intermediate inspection. Exceptional checks: 4.7.1 to 4.7.7 Type Approval Initial inspection and test

Tanks with shells of Metallic Materials * (chapter 6.8) Fixed tanks (road tanks) Tank wagons (rail tanks) Demountable tanks Tank containers Tank swap bodies Battery vehicles (road) Battery wagons (rail) MEGCs for substances of Class(s) 3, 4, 5, 6, 8 & 9

EN 12972:2018 EN 12493:2001 (Except Annex C) EN 12493:2008 (Except Annex C) EN 12493:2008+A1:2012 (Except Annex C) EN 12493:2013 (Except Annex C) EN 12493:2013+A1:2014+ AC:2015 (Except Annex C) EN 13094:2015 EN 14025:2003+AC:2005 EN 14025:2008 EN 14025:2013 EN 14025:2013+A1:2016 (except Annex B) EN 13530-2:2002 EN 13530-2:2002/A1:2004 EN 14398-2:2003- (Except table 1) EN 14432:2014 EN 14433:2014 IMS03 procedures for containers

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code

The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment (Amendment) (EU Exit) Regulations 2020.

ADR 6.8 ‘GB Only’

Conformity assessment Supervision of manufacture Initial inspection and test Exceptional checks: 4.7.1 to 4.7.7 Periodic inspection & Intermediate inspection.

Tanks with shells of Metallic Materials * (chapter 6.8) Fixed tanks (road tanks) Tank wagons (rail tanks) Demountable tanks Tank containers Tank swap bodies Battery vehicles (road) Battery wagons (rail) MEGCs for substances of Class 2

Conformity Assessment according to ADR 1.8.7 EN 12972:2018 EN 12493:2001 (Except Annex C) EN 12493:2008 (Except Annex C) EN 12493:2008+A1:2012 (Except Annex C) EN12493:2013 (Except Annex C) EN12493:2013+A1:2014+AC:2015 (Except Annex C) EN 13530-2:2002 EN 13530-2:2002+A1:2004 EN 14025:2003+AC:2005 EN 14025:2008 EN 14025:2013 EN 14025:2013+A1:2016 (except annex B) EN 14398-2:2003 EN 14432:2014 EN 14433:2014 IMS03 procedures for containers

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code

The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment (Amendment) (EU Exit) Regulations 2020 The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment (Northern Ireland) Regulations 2010 (as amended). The Merchant Shipping (Dangerous Goods and marine Pollutants) regulations 1997

RID, ADR and the IMDG Code, Chapter 6.7

Periodic inspection & Intermediate inspections. Exceptional checks: 4.5.1 to 4.5.6 Type Approval Supervision of construction Initial inspection and test

Portable Tanks* for substances of Class(s) 2, 3, 4, 5, 6, 8 & 9 UN MEGCs*

EN 12972 EN 14025 PD 5500 ASME VIII : Div.1 ASME VIII : Div.2 AD 2000 (Merkblatt) CODAP 2000 : Stoomwezen IMS03 procedures for containers

A

IMDG Code, Chapter 6.7

Periodic inspection & Intermediate inspections. Exceptional checks: Type Approval Supervision of construction Initial inspection and test With exception of lifting sets

Offshore portable containers*

BS EN ISO 10855-1:2018 BS EN ISO 10855-3:2018 IMO MSC/Circ.860 EN 12079-1:2006 withdrawn EN 12079-3:2006 withdrawn IMS03 procedures for containers

A

The Merchant Shipping (Dangerous Goods and marine Pollutants) regulations 1997

Periodic inspection & Intermediate inspections. Exceptional checks

IMO Type 1,2,5 & 7 Portable tanks* IMO Type 4,6 & 8 Road tank vehicles*

EN 12972:2018 IMO DSC/Circ.12 (as

amended)

A

IMS03 procedures for containers

0003


Accredited to

ISO/IEC 17020:2012











Location Code

The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment (Amendment) (EU Exit) Regulations 2020 The Carriage of Dangerous Goods & Use of Transportable Pressure Equipment (Northern Ireland) Regulations 2010 (as amended).

Old Pressure Receptacles*

Periodic in-service Inspection

Cryogenic vessel EN 1251-3:2000 Composite Cylinders EN 11623:2002 (except clause 4) Seamless Steel Cylinders EN 1968:2002+A1:2005 (except Annex B) Seamless Aluminium Alloy Cylinders EN 1802:2002 (except Annex B) Welded Carbon Steel Cylinders EN 1803:2002 (except Annex B) Welded Steel Pressure Drums EN 14876:2007 Cylinder Valves EN ISO 22434:2011 Gas Cylinders ISO 10460:2005 ISO 10461:2006 ISO 6406:2005

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code

The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment (Amendment) (EU Exit) Regulations 2020:

Transportable Pressure Receptacles* ADR 6.2.3, 6.2.4 Non UN Pressure Receptacles

Periodic in-service Inspection including: Periodic inspection, intermediate inspection, and exceptional checks. Surveillance of applicant’s in-house inspection service.

Including ADR 1.8.7 procedures for periodic inspection Composite Cylinders EN 11623:2015 (except clause 4) Seamless Steel Cylinders EN 1968:2002+A1:2005 (except Annex B) Seamless Aluminium Alloy Cylinders EN 1802:2002 (except Annex B) Welded Carbon Steel Cylinders EN 1803:2002 (except Annex B) Welded Steel Pressure Drums EN 14876:2007 Cryogenic Vessels EN 1251-3:2000 Cylinder Valves EN ISO 22434:2011 Gas Cylinders ISO 10460:2005 ISO 10461:2006 ISO 6406:2005

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code


Transportable Pressure Receptacles* ADR 6.2.2 UN Pressure Receptacles

ADR 6.2.3, 6.2.4 Non UN Pressure Receptacles

Conformity assessment including: - Type approval. - Supervision of manufacture. - Initial inspection and test - Surveillance of applicant’s in-house inspection service.

Including ADR 1.8.7 procedures for conformity assessment inspection (Non-UN Pressure Receptacles) EN 1251-2:2000 EN 1442:1198+A2 :2005 EN 1442:2006+A1:2008 EN 1964-1:1999 EN 1964-2:2001 EN 1964-3:2000 EN ISO 9809-1:2010 EN ISO 9809-2:2010 EN ISO 9809-3:2010 EN ISO 10961:2012 EN ISO 11118:2015 EN ISO 11120:1999 EN 1975:1999+A1:2003 EN 12205:2001 EN 12245:2002 EN 12245:2002+A1 :2009 EN 12257:2002 EN 13293:2002 EN 13322-1:2003+A1:2006 EN 13322-2:2003+A1:2006 EN 13769:2003+A1:2005 (until 31/12/14) EN 14140:2003+A1:2006 EN 14140:2014+AC:2015 (except over-moulded cylinders) EN 14208:2004 ISO 9809-1:2010 ISO 9809-2:2010 ISO 9809-3:2010 ISO 7866:1999 EN ISO 7866:2012+AC:2014 ISO 7866:2012+AC:2014 ISO 11118:1999 ISO 11118:2015 ISO 11120:1999

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code


Transportable Pressure Receptacle Closures* ADR 6.2.2 ADR 6.2.4

Conformity assessment including: - Type approval. - Supervision of manufacture. - Initial inspection and test - Surveillance of applicant’s in-house inspection service.

Including ADR 1.8.7 procedures for conformity assessment and periodic inspection Cylinder valves EN 849:1996+A2:2001 EN 13152:2001+A1:2003 EN 13153:2001+A1:2003 EN ISO 10297:2014 EN ISO 10297:2014+A1:2017 EN ISO 17879:2017 ISO 10297:2014

A

Pressure Receptacles

New construction verification

TPSR Issue 1 - Cylinders for oil well samples A

Note: The inspection of items marked thus * are subject to legislative requirements including the appointment of ‘persons’ to carry out inspections. Reference should be made to the VCA Dangerous Goods Office for information on this and listings of bodies recognised under UK legislation.

0003


Accredited to

ISO/IEC 17020:2012







Accreditation for the purpose of UK Approved Body Activity in accordance with UKCA Requirements and UKAS Publication GEN 5

Directive/Regulation Conformity Assessment procedure/Module/Article



Location Code

Pressure Equipment (Safety) Regulations 2016

Directive: Article 14:Annex III Regulation: 42 Conformity Assessment Modules A2, B, C2, D, D1, E, E1, F, G, H, H1

All descriptions of pressure equipment and assemblies covered by the Regulations.

IMS03-04-01 IMS03-04-05 IMS03-04-75

A

Directive: Article 15

Regulation: 50

Issuing European Approval of Materials

IMS03-04-01 IMS03-04-05 IMS03-04-75

A

Directive: Annex I – 3.1.2

Regulations: Schedule 2 paragraph 21

Categories II III and IV Approval of permanent joining procedures and personnel

IMS03-04-01 IMS03-04-05 IMS03-04-76

A



Categories III and IV Approval of personnel to carry out non-destructive test on permanent joints for pressure equipment

IMS03-04-01 IMS03-04-05 IMS03-04-77

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code

Simple Pressure Vessels (Safety) Regulations 2016

Directive: Article 13: Annex II Regulation: Schedule 2 Conformity Assessment Modules B, C1, C2, C

Simple Pressure Vessels manufactured in series

IMS03-04-01 IMS03-04-05

A

Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016

Article 13 (1) (b) (ii), Annex VIII

Storage of Technical files

Acknowledgment of receipt and retention of technical files

A

Supply of Machinery (Safety) Regulations 2008

Directive: Article 12 (3)b and (4)a :Annex IX Regulation: Schedule 2 Part 9 EC Type Examination

Annex IV items 1 - 23 Part 4 items 1 - 23 Annex V items 1-5 Part 5 items 1-5

IMS03-04-01 IMS03-04-05 IMS03-04-73

A

Directive: Article 12 (3)c and (4)b :Annex X Regulation: Schedule 2 Part 10 Full Quality Assurance


IMS03-04-01 IMS03-04-05 IMS03-04-73

A

Note: The inspection of items marked thus ** are subject to legislative requirements including the appointment of ‘persons’ to carry out inspections. Reference should be made to BEIS for information on this and listings of bodies recognised under UK legislation.

0003


Accredited to

ISO/IEC 17020:2012










Essential requirements:Product specification/ Properties/Standards

Location Code

Construction Products Regulation 2011 (retained EU law EUR 305/2011) as amended by the Construction Products (Amendment etc.) (EU Exit) Regulations 2019 and the Construction Products (Amendment etc.) (EU Exit) Regulations 2020.**

Annex V- Factory Production Control (System 2+)

94/611/EC 1/4 Metal Fabrication

EN 1090-1:2009+AC:2010 +A1:2011

A


95/467/EC 1/1 Chimneys, flues and specific products

EN 416-1:2009 EN 777-1:2009 EN 777-2:2009 EN 777-3:2009 EN 777-4:2009 EN1457:1999/A1:2002 EN1457:1999/A1:2002/AC:2007 EN 1457:1999/AC:2006 EN 1856-1:2003/A1:2006 EN 1856-1:2009 EN 1856-2:2009 EN 1857:2003+A1:2008 EN 1857:2010 EN 1858:2008+A1:2011 EN 12446:2011 EN 13063-1:2007 EN 13063-2:2007 EN 13069:2005 EN 13084-5:2005 EN 13084-5:2005/AC:2006 EN 13084-7:2005 EN 13084-7:2005/AC:2009 EN 14471:2005 EN 14989-2:2007

A

0003


Accredited to

ISO/IEC 17020:2012











Location

Code

Construction Products Regulation 2011 (retained EU law EUR 305/2011) as amended by the Construction Products (Amendment etc.) (EU Exit) Regulations 2019 and the Construction Products (Amendment etc.) (EU Exit) Regulations 2020.** (cont’d)


97/555/EC Cements, building limes and hydraulic binders

EN 459-1;2001 EN 459-1:2001/AC:2002 EN 459-1:2010

A

Annex V-

Factory Production Control (System 2+)

98/214/EC 1/4 Structural metallic products and ancillaries

EN 10025-1:2004 EN 10088-4:2009 EN 10088-5:2009 EN 10210-1:2006 EN 10219-1:2006 EN 10340:2007 EN 10340:2007/AC:2008 EN 10343:2009 EN 15048-1:2007 EN 15088:2005

A

0003


Accredited to

ISO/IEC 17020:2012











Location

Code




EN 13479:2009

A



EN 14399-1:2015 A


98/598/EC 2/2 Aggregates for use with high safety requirements

EN 12620:2002+A1:2008 EN 13043:2002 EN 13043:2002/AC:2004 EN 13055-1:2002 EN 13055-1:2002/AC:2004 EN 13055-2:2004 EN 13139:2002 EN 13139:2002/AC:2004 EN 13242:2002+A1:2007 EN 13383-1:2002 EN 13383-1:2002/AC:2004 EN 13450:2002 EN 13450:2002/AC:2004

A

0003


Accredited to

ISO/IEC 17020:2012











Location

Code



98/601/EC 1/2 Road Construction products

EN 12271:2006 EN 12273:2008 EN 12591:2009 EN 13108-1:2006 EN 13108-1:2006/AC:2008 EN 13108-2:2006 EN 13108-2:2006/AC:2008 EN 13108-3:2006 EN 13108-3:2006/AC:2008 EN 13108-4:2006 EN 13108-4:2006/AC:2008 EN 13108-5:2006 EN 13108-5:2006/AC:2008 EN 13108-6:2006 EN 13108-6:2006/AC:2008 EN 13108-7:2006 EN 13108-7:2006/AC:2008 EN 13808:2005 EN 13924:2006 EN 13924:2006/AC:2006 EN 14023:2010 EN 15322:2009

A



99/469/EC 1/2 Products related to concrete, mortar and grout

EN 450-1:2005+A1:2007 EN 934-2:2001/A2:2005 EN 934-2:2009 EN 934-3:2003/AC:2005 EN 934-3:2009 EN 934-4:2009 EN 934-5:2007 EN 1504-2:2004 EN 1504-3:2005 EN 1504-4:2004 EN 1504-5:2004 EN 1504-7:2006 EN 12878:2005 EN 12878:2005/AC:2006

A

0003


Accredited to

ISO/IEC 17020:2012







Accreditation for the purpose of Notified Body Activity relating to the Northern Ireland market (CE + UKNI) taking into account EA-2/17

Directive/Regulation Conformity Assessment

procedure/Module/Article Category of products or individual products


Location Code

Pressure Equipment (Directive 2014/68/EU) implemented in Northern Ireland by the Pressure Equipment (Safety) Regulation 2016

Directive: Article 14:Annex III Regulation: 42 Conformity Assessment Modules A2, B, C2, D, D1, E, E1, F, G, H, H1

All descriptions of pressure equipment and assemblies covered by the Regulations.

IMS03-04-01 IMS03-04-05 IMS03-04-75

A

Directive: Article 15

Regulation: 50

Issuing European Approval of Materials

IMS03-04-01 IMS03-04-05 IMS03-04-75

A



Categories II III and IV Approval of permanent joining procedures and personnel

IMS03-04-01 IMS03-04-05 IMS03-04-76

A



Categories III and IV Approval of personnel to carry out non-destructive test on permanent joints for pressure equipment

IMS03-04-01 IMS03-04-05 IMS03-04-77

A

0003


Accredited to

ISO/IEC 17020:2012







Simple Pressure Vessels (Directive 2014/29/EU) implemented in Northern Ireland by the Simple Pressure Vessels (Safety) Regulations 2016

Directive: Article 13: Annex II Regulation: Schedule 2 Conformity Assessment Modules B, C1, C2, C

Simple Pressure Vessels manufactured in series

IMS03-04-01 IMS03-04-05

A

Equipment Intended for use in Potentially Explosive Atmospheres (ATEX) (Regulation 2014/34/EU) implemented in Northern Ireland by the Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016

Article 13 (1) (b) (ii), Annex VIII

Storage of Technical files

Acknowledgment of receipt and retention of technical files

A

Machinery (Directive 2006/42/EC) implemented in Northern Ireland by the Supply of Machinery (Safety) Regulations 2008

Directive: Article 12 (3)b and (4)a :Annex IX Regulation: Schedule 2 Part 9 EC Type Examination


IMS03-04-01 IMS03-04-05 IMS03-04-73

A

Directive: Article 12 (3)c and (4)b :Annex X Regulation: Schedule 2 Part 10 Full Quality Assurance


IMS03-04-01 IMS03-04-05 IMS03-04-73

A

0003


Accredited to

ISO/IEC 17020:2012







Note: The inspection of items marked thus ** are subject to legislative requirements including the appointment of ‘persons’ to carry out inspections. Reference should be made to BEIS for information on this and listings of bodies recognised under UK legislation.

Construction Products Regulation 2011 (retained EU law EUR 305/2011) as amended by the Construction Products (Amendment etc.) (EU Exit) Regulations 2019 and the Construction Products (Amendment etc.) (EU Exit) Regulations 2020**


94/611/EC 1/4 Metal Fabrication

EN 1090-1:2009+AC:2010 +A1:2011

A


95/467/EC 1/1 Chimneys, flues and specific products

EN 416-1:2009 EN 777-1:2009 EN 777-2:2009 EN 777-3:2009 EN 777-4:2009 EN1457:1999/A1:2002 EN1457:1999/A1:2002/AC:2007 EN 1457:1999/AC:2006 EN 1856-1:2003/A1:2006 EN 1856-1:2009 EN 1856-2:2009 EN 1857:2003+A1:2008 EN 1857:2010 EN 1858:2008+A1:2011 EN 12446:2011 EN 13063-1:2007 EN 13063-2:2007 EN 13069:2005 EN 13084-5:2005 EN 13084-5:2005/AC:2006 EN 13084-7:2005 EN 13084-7:2005/AC:2009 EN 14471:2005 EN 14989-2:2007

A

0003


Accredited to

ISO/IEC 17020:2012











Location

Code

Construction Products Regulation 2011 (retained EU law EUR 305/2011) as amended by the Construction Products (Amendment etc.) (EU Exit) Regulations 2019 and the Construction Products (Amendment etc.) (EU Exit) Regulations 2020** (cont’d)


97/555/EC Cements, building limes and hydraulic binders

EN 459-1:2001 EN 459-1:2001/AC:2002 EN 459-1:2010

A

Annex V-



EN 10025-1:2004 EN 10088-4:2009 EN 10088-5:2009 EN 10210-1:2006 EN 10219-1:2006 EN 10340:2007 EN 10340:2007/AC:2008 EN 10343:2009 EN 15048-1:2007 EN 15088:2005

A

0003


Accredited to

ISO/IEC 17020:2012











Location

Code




EN 13479:2009

A



EN 14399-1:2015 A

Annex V-


98/598/EC 2/2 Aggregates for use with high safety requirements

EN 12620;2002+A1:2008 EN 13043:2002 EN 13043:2002/AC:2004 EN 13055-1:2002 EN 13055-1:2002/AC:2004 EN 13055-2:2004 EN 13139:2002 EN 13139:2002/AC:2004 EN 13242:2002+A1:2007 EN 13383-1:2002 EN 13383-1:2002/AC:2004 EN 13450:2002 EN 13450:2002/AC:2004

A

0003


Accredited to

ISO/IEC 17020:2012











Location

Code



98/601/EC 1/2 Road Construction products

EN 12271:2006 EN 12273:2008 EN 12591:2009 EN 13108-1:2006 EN 13108-1:2006/AC:2008 EN 13108-2:2006 EN 13108-2:2006/AC:2008 EN 13108-3:2006 EN 13108-3:2006/AC:2008 EN 13108-4:2006 EN 13108-4:2006/AC:2008 EN 13108-5:2006 EN 13108-5:2006/AC:2008 EN 13108-6:2006 EN 13108-6:2006/AC:2008 EN 13108-7:2006 EN 13108-7:2006/AC:2008 EN 13808:2005 EN 13924:2006 EN 13924:2006/AC:2006 EN 14023:2010 EN 15322:2009

A

0003


Accredited to

ISO/IEC 17020:2012











Location Code



99/469/EC 1/2 Products related to concrete, mortar and grout

EN 450-1:2005+A1:2007 EN 934-2:2001/A2:2005 EN 934-2:2009 EN 934-3:2003/AC:2005 EN 934-3:2009 EN 934-4:2009 EN 934-5:2007 EN 1504-2:2004 EN 1504-3:2005 EN 1504-4:2004 EN 1504-5:2004 EN 1504-7:2006 EN 12878:2005 EN 12878:2005/AC:2006

A

Note: The inspection of items marked thus ** are subject to legislative requirements including the appointment of

‘persons or bodies’ to carry out conformity assessment. Reference should be made to the relevant Government Departments (BEIS for PER and SPVR, DCLG for CPR) for information on this and listings of bodies recognised under UK legislation

END

Documents

issued by United Kingdom Accreditation Service · 2021. 1. 13. · BS EN ISO 10855-1:2018 BS EN ISO 10855-3:2018 IMO MSC/Circ.860 EN 12079-1: 2006 withdrawn EN 12079-3: 2006 withdrawn