1

JAMES ENGINEERING PTY LTD ABN 63 101 887 950

PO Box 1331 Browns Plains Qld 4118 Ph: 07 3879 2500 Fax: 07 3879 2511

email: sales@jameseng.com.au

1. Company Introduction

James Engineering Pty Ltd was established in 1963 as a general building contractor specialising in remote and difficult locations. In the early 1970’s James Engineering developed a range of commercial/industrial transportable buildings which were seen as a commercially and technically superior solution to traditional construction methods, particularly in the isolated and harsh Australian conditions. Since 1995 the company has concentrated predominantly on the supply of prefabricated electrical switchrooms. James Engineering has evolved into the leading supplier of Custom Designed Transportable Buildings to the Mining, Power Generation and Process industries. James Engineering operates from company owned premises at Heathwood on the Southside of Brisbane for assembly and James Steel in Toowoomba for steel fabrications.

2. Capabilities

2.1 James Engineering James Engineering (including James Steel & James Electrical) is an engineering, design and project management company which specialized in switchroom works and have completed over 2000 rooms for the mining & resources, power generation, utilities and renewable energy. James Engineering Heathwood premises would include the following; • 15,000m² with 6,000m²of undercover manufacturing and fit-out space

• Dedicated level concrete hardstand for equipment installation and FAT testing • Undercover equipment storage area • A dedicated air conditioned equipment storage area A typical scope of work for James Engineering would include the following:

• Design, engineering and certification for; • Building structure for equipment weights and lifting loads • Wind and earthquake load requirements • Footings and support structures • Access platforms and stairways • Fire rating installation • HVAC and ventilation systems • Fire and gas systems • Equipment installation/integration, testing and commissioning • Cable ladder and cable supply and installation

James Engineering owns a significant amount of equipment for material handling and a prime mover. This allows James Engineering to have an edge over its competitors and would eliminate delivery risks and have better control over scheduled works. Whether it is a skid, process plant or solar farm switchroom James Engineering can draw on internal experienced resources to ensure a successful completion and deliver on time anywhere in Australia.

2

2.2 James Steel James Steel is a professional steel fabrication business operates from Toowoomba, including in house drafting. James Steel takes pride in its team, and only uses in house trained personnel for specialty work such as steel fabrication and painting. Works for James Steel would include the following: • Mobile skids • Electrical kiosks • Switchrooms and building support structures • General structural steel fabrications • Farm equipment modifications • Fencing • Plate and sheet folding and rolling • Blasting and painting

2.3 James Electrical James Electrical Installations worked exclusively to James Engineering Pty. Ltd. since July 2012. Our roll with James Engineering has been to work closely with James Electrical Installations and the principal contractors to complete the electrical fit-out of their transportable switchrooms at the James Engineering facility, Heathwood. Works typically include: -

• Receiving, unloading and unpacking free issued Electrical Equipment panels and loose items, including indoor secure storage of equipment until required for installation.

• Installation into switchroom, positioning and fixing of free issued panels and switchboards as shown per project drawings.

• Supply, installation of switchroom light & power including Light and Power Distribution board.

• Assembly of HV & LV switchboard sections including assembly of main bus bars between switchgear shipping sections including torqueing of bolts, fitting of any additional insulation or covers, joint resistance testing and insulation resistance testing of main bus.

• Installation and connection of interpanel wiring looms between switchboard shipping sections, plus point to point testing of interconnections.

• When required, installation and assembly of HV switchgear arc duct on switchgear & arc vents through external wall penetrations. When not supplied, we can assist with supply of specialised arc vent to clients’ approval.

• Supply, installation and earthing of cable ladder suspended from ceiling inside the switchroom and under floor cable ladder within the switchroom baseframe, for cabling between equipment panels and switchboards.

• Supply, installation and termination of Switchroom earth bar(s) and earthing cabling as per clients’ requirements, for the earthing of switchroom baseframe, switchboards, cable ladder and electrical panels.

• Supply, installation termination and testing of cabling within the Switchroom between equipment panels as per client documentation.

• When required supply and installation of floor mounted gland plates, or fabricated steel box’s fixed and sealed to the floor under switchgear panels, fitted with gland plates below floor level for termination of field cables.

• Wall mounted cable ladder and cable mechanical protection as required for wall mounted equipment panels.

• Supervision and management of our works and coordination with James Engineering and client.

• Temporary floor protection as required.

• Shoring and packing for road transport including loading and securing loose items within the switchroom.

• Disposal of all equipment packaging and rubbish, and clean-up of Switchroom prior to despatch.

• We can assist with client FAT by arranging temporary test supplies, barricading areas under test, supply labour and test equipment to assist.

• Provide ITP’s and test documentation of all tests completed by James Electrical Installations, or complete clients test documentation.

• Work with client to rectify free issued equipment issues, changes or modifications.

• On Site work if required by client to complete any further installation works, equipment changes or rectification.

3

3. Projects include • Gorgon Project (Barrow Island LNG Plant, Western Australia)

32 substations, largest 28m x 7m

• Comalco Alumina Refinery (Gladstone Queensland) 24 substations, largest 26m x 7.20m

• Goro Nickel Mine (New Caledonia) 32 substations, largest 43m x 7.40m

• Sepon Copper Mine (Thailand) 14 substations, largest 26m x 6m

• Lihir Gold Mine (Papua New Guinea)

24 substations, largest 28.0m x 6.40m, including multi storey

• Powerlink (Queensland) Over 50 Control Room, Amenities rooms and combined Control & Amenities Rooms

• Queensland Rail Over 30 Traction and Feeder substation for various QR location such as Roma Street, Milton, Darra, Mitchelton, Petrie, Moreton Bay.

• RTA Amrun Project (Bauxite Mine, Weipa North Queensland)

13 substations, largest being 77.3m long x 8.9m wide (5 sections)

• Clare Solar (Ayr, North Queensland) 1 x 33kV Switchroom & Control room, 23m long x 5.5m wide

• RTA Kestrel Mine (Central Queensland) 1 x Vents Switchroom 24m long x 4.9m wide

• Ross River Solar Farm (Townsville, Queensland) 1 x 33kV Switchroom & Control room 26.5m long x 5.5m wide

4. Major Clients • Bechtel Australia • Fluor • Siemens • Aurecon Hatch • Ausenco • Nilsen • ABB • Schneider Electrics • Xstrata • Siemens • Downer • UGL

“Why would you go anywhere else than James for a building”.

4

5. James Engineering Facility

Main Office

Switchroom Bays

5

Switchroom Bays

Storage & Smaller Switchroom Bay

6

Outdoor Bay & Office for Client’s FAT

6. Project Photos

2006 - KENYA TO CHINCHILLA PIPELINE

7

2040 - NCIG STAGE 2F PROJECT - HV Room

8

2050 - MAULES CREEK PROJECT

9

Boddington Gold Photos

10

Zinifex-CENTURY MINE

Mt Isa Mines

11

Sepon Copper

RTA Amrun Project Weipa

12

13

Downer Clare Solar Project

Queensland Rail Brunswick Street

14