J.C.BOSE UNIVERSITY OF SCIENCE &

TECHNOLOGY,YMCA, FARIDABAD Delhi-Mathura Road, Sector-6, Faridabad

(Established by the State Legislative Act 21/2009)

NAAC Accredited ‘A’ Grade State Govt. University

Department of Mechanical Engineering

Name: Dr. MOHAN LAL AGGARWAL FACULTY (ME)

Designation: Professor Qualifications: 1. B.Sc. (Mechanical Engineering) from REC Kurukshetra ( Presently NIT Kurukshetra),1988. 2. M.Tech. Design of Mechanical Equipments, 2003, IIT New Delhi 3. Ph.D. in Design from Jamia Millia Islamia, May 2007,New Dehli D.O.B.: August 24, 1965 Experience: 32 years teaching in J C Bose University of Sc & Technology ( Formerly, YMCA University of Sc &Technology Faridabad), 0.5 Year Industrial experience. Contact: aggarwalmlal@gmail.com

Publications:

INTERNATIONAL JOURNAL

1. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,Investigation into the effects of shot peening on the fretting fatigue behaviour of 65Si7 spring steel leaf springs, Journal of Materials : Design and Applications, I.Mech.Engrs., U.K., Vol 219(3), 2005,pp139-147 ,Impact Factor =0.56 (www.pepublishing.com), SCI

2. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,A stress approach model for predicting fatigue life of shot peened EN45A spring steel, International Journal of Fatigue, Elsevier Publication,28(12),Dec.2006,pp1845-853,Impact Factor=1.020 (www.sciencedirect.com). SCI

3. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,Effect of surface roughness on fretting fatigue

behaviour of EN-45A spring steel leaf springs, Journal of Engineering Manufacture, Institution of Mechanical Engineers UK, Vol.220(8), 2006, pp1325-1333. Impact Factor=0.77 ( www.pepublishing.com). SCI

4. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,A Novel approach for improving fatigue strength of

shot peened surfaces by damping measurements,International Journal of Manufacturing Technology and Research,Vol.2, No.1&2,June 2006,pp 30-34.

5. M.L.ggarwal,R.A.Khan and R.K.Garg, When shot-peening does not enhance fatigue life of leaf springs, International Journal of Surface Science and Engg.,Vol.2(nos.3/4),2008,pp281-293,Impact Factor= 0.48 (www.inderscience.com). SCI

6. Lakhwinder Singh, R.A. Khan, M.L. Aggarwal, “Effect of shot peening on hardening and

surface roughness of nitrogen austenitic stainless steel”, International journal of Engineering Science and Technology, vol 2(4), 2010, pp 818-826.

7. Vinkel Arora,Gian Bhushan and M.L.Aggarwal “Eye design analysis of single leaf spring in automotive vehicles using CAE tools,International Journal of Applied Engg.&Technoloy,Vol.1(1), 2011,pp.88-97, Impact Factor =0.302.

8. Vinkel Arora, M.L.Aggarwal and Gian Bhushan “A comparative study of CAE and experimental results of leaf springs in automotive vehicles,International Journal of Engineering Science &Technology,2011,Vol.3(9),pp.6856-66.

9. Kumar Krishan and M.L.Aggarwal “A finite element approach for analysis of a multileaf spring using CAE tools,Research Journal of Recent Sciences,Vol.1(2),2012,pp92-96,Impact Factor =0.372

10. Lakhwinder Singh, R.A. Khan, M.L. Aggarwal, “Effect of relaxed residual stress on fatigue design reliability of AISI 304 stainless steel”, The journal of Engineering Research, Vol. 8, No. 1, 2011, pp 44-52.

11. Lakhwinder Singh, R.A. Khan, M.L. Aggarwal, Relationship between damping factor and compressive residual stress for shot peened austenitic stainless steel, ISRN Mechanical Engineering: An Open access Journal , Vol. 2011, 7 pages,doi:10.5402/2011/867484.

12. Kumar Krishan and M.L.Aggarwal “Computer aided FEA comparison of mono steel and mono

GRP leaf spring, International Journal of Advanced Research &Studies,Vol.1(2),2012,pp 155-58.

13. Lakhwinder Singh,R.A.Khan,M.L.Aggarwal,’ Emperical modeling of shot peening parameters

for welded austenitic stainless steel using grey relational analysis,Journal of Mechanical Science &Technology,Vol.26(6), 2012, pp 1731-39, Impact Factor =0.616. SCI

14. Devdutt and M.L.Aggarwal, Fuzzy control of seat vibrations for semi-active quarter vehicle system utilizing magneto- rheological damper, International Journal of Engineering Inventions, Vol.1,Issue 12,2012,ISSN 2278-7461,pp 51-56, Impact Factor =1.212.

15. M.L.Aggarwal and S.K.Bhardwaj , Effect of tooth deformation on contact ratio and tooth sresses in plastic spur gears, International Journal of Engineering Sciences ,ISSN Online:2277-9698, 2013 ,pp 69-71 (www.ijmrs.com).

16. Krishan Kumar and M.L.Aggarwal, Computer aided FEA simulation of EN45A parabolic leaf springs”, International Journal of Industrial Engineering Computations, Growing Science publishers, ISSN: 1923-2934, Vol.4, Issue 2, Pp: 297-304, 2013, Impact Factor =0.131

SCOPUS.

17. Pawan Kumar Taneja,M.L.Aggarwal and Vakaar Ali, A study on various gear and their prevention,International Journal of Engineering Research &Technology,ISSN 0974-3154,Vol.6,No.6,August 2013,pp83-87 Impact Factor =1.76,(www.irphouse.com).

18. M.L.Aggarwal, Finite element modeling for replacement of C.I. pulley with suitable material,Int. Journal of Modern Engg. Research,Vol.2,Issue-5,Sept-Oct 2012

19. Arora Vinkel, Bhushan Gian, Aggarwal M L, Fatigue life prediction of leaf springs in automotive vehicles using CAE tools” , Int. J. of Computer Aided Engineering & Technology,Inder Science Publications, Vol.6, pp 271-76, 2014

20. Devdutt,M.L.Aggarwal, “Fuzzy logic control of a semi-active quarter car system” International Journal of Mechanical,Industrial Sc&Engineering,Vol.8,No.1,2014 ,pp163-67.

21. Jitisha Aggarwal, M.L.Aggarwal, Harnessing solar energy for every home: Energy saving applications,Open access Journal: Conference paper in Sc,Vol.2014,Article ID 628294,3pages,d.o.i.10.1155/2014/628294,2014(Hindawi Publishing Corporation).

22. Vinkel Kumar Arora, Gian Bhushan and M.L Aggarwal, Effect of assembly stresses on

fatigue life of symmetrical 65Si7 leaf springs, , International Scholarly Research Journal ,

Hindawi Publishing Corporation, Article ID 762561, 10 pages, 2014.

doi:10.1155/2014/7625612014.

23. Vinkel Arora,Gian Bhushan & M.L .Aggarwal, Fatigue Life Assessment of 65Si7 Leaf

Springs: A Comparative Study, International Scholarly Research Notices,vol. 2014, Article ID

607272, 11 pages, 2014. doi:10.1155/2014/607272.

24. Sonu Yadav and M L Aggarwal , Effect of Lifting Load on Solar Powered Screw Jack Design

in Automotive Vehicles, Journal for Scientific Research and Development, volume 2, issue

10,pp 137-148, Dec. 2014.

25. Devdutt ,M.L.Aggarwal , Fuzzy Control of Passenger Ride Performance using MR Shock

Absorber Suspension in Quarter Car Model, International Journal of Dynamics and Control,

Springerlink DOI 10.1007/s40435-014-0128-z, 2015, Volume 3, Issue 4, pp 463–469.

SCOPUS.

26. Devdutt, M.L. Aggarwal, Passenger seat vibration control of semi-active quarter car system

with fuzzy controller, YMCAUST International Journal of Research, Volume 2, Issue 1, 2014,

pp. 6-14.

27. Atul Sharma, M.L.Aggarwal, Lakhwinder Singh, Shot Peening for Improving Surfacce

Properties of MMC Spur Gear, Journal: Indian Institute of Metals, NIT Srinagar, Vol. 02, issue-

4, May 2014.

28. Atul Sharma, M.L.Aggarwal, Lakhwinder Singh, Effect of Fillet Radius on Aluminium Silicon

Carbide Metal Matrix Composite Spur Gear, Journal of Recent Advances in Mechanical

Engineering, Volume 4, No. 2.,pp137-47, 2015.

29. Devdutt ,M.L.Aggarwal, Passenger Seat Vibration Control of Quarter Car System with MR

Shock Absorber, Journal of Computer, Information, Mechatronics, Systems Science and

Engineering, Volume 8,No. 5, 2015,pp 707-714.

30. Devdutt ,M.L.Aggarwal, Comparative Analysis of Passenger Ride Comfort Using Various

Semi-Active Suspension Alternatives, Journal of Recent advances in Mechanical Engineering

(IJMECH), Wireilla Scientific Publications Volume 3, No. 3, 2015,pp 79-89.

31. Devdutt ,M.L.Aggarwal, Simultaneous Optimization of Semi-active Quarter Car Suspension

Parameters Using Taguchi Method and Grey Relational Analysis, Journal of Recent advances

in Mechanical Engineering (IJMECH), Wireilla Scientific Publications Vol.4, No.1, 2015, pp.

61-75.

32. Vinkel Arora,Gian Bhushan & M.L .Aggarwal , Static Structural CAE analysis of Symmetrical

65Si7 Leaf Springs in Automotive Vehicles , Engineering Solid Mechanics, Vol. 3(1), pp. 59-

74, 2015 , SCOPUS.

33. Vinkel Arora,Gian Bhushan & M.L .Aggarwal , A Comparative Study of Standard, Casted and

Riveted Eye Design of a Mono Leaf Spring Using CAE Tools, International Journal of

Mechanical, Aerospace, Industrial and Mechatronics Engineering Vol:9, No:1, 2015

34. Krishan Kumar and M.L.Aggarwal, Finite element analysis and optimization of a mono parabolic leaf

spring using CAE software, Journal : Engineering Solid Mechanics, Vol.3,2015, pp85-92. SCOPUS.

35. Krishan Kumar and M.L.Aggarwal, Simulation for optimized modeling of EN45A leaf spring,

International Journal of recent advances in Mechanical Engineering,Vol.4,No.3,2015,pp129-

141.

36. Krishan Kumar and M.L.Aggarwal, Fatigue life prediction: A comparative study for a three

layer EN45A parabolic leaf spring, Journal : Engineering Solid Mechanics, Vol.3,2015, pp17-

166. SCOPUS.

37. Suresh Kumar, M.L.Aggarwal and Lakhwinder Singh, Finite element analysis of open coil

helical springs,Inverties Journal of Sc. & Technology,Vol.8,No.3,2015,pp 129-131.

38. Atul Sharma, M.L.Aggarwal, Lakhwinder Singh, Effect of fillet radius on Aluminium Silicon

Carbide metal matrix composite spur gear, International Journal of recent advances in

Mechanical Engineering,Vol.4,No.2, May 2015 ,pp137-147.

39. Sonu Yadav and M.L.Aggarwal, Feasibility study of utilizing solar energy in automobile air

conditioning, International recognized double-blind peer reviewed multidisciplinary research

Journal, ISSN 2231-5063, Vol.4,Issue-11,May 2015,pp1-8.

40. Devdutt, M. L. Aggarwal, Active Vibration Control of Passenger Seat with HFPIDCR

Controlled Suspension Alternatives, International Journal of Mechanical, Aerospace,

Industrial, Mechatronic and Manufacturing Engineering Vol:10, No:5, 2016,pp 916-23.

41. Vinkel Arora,Gian Bhushan & M.L .Aggarwal , Effect of Surface Decarburisation, Scragging

Stress and Individual Leaf Camber on Fatigue Life of 65Si7 Leaf Springs, International

Journal of Design Engineering,Vol.6 ,No.1 ,2015,pp22-44. (Inderscience).

42. Arora, V. K., Bhushan, G., & Aggarwal, M. L. (2016). Effect of geometry, material and strength

reduction factor on the fatigue life of the symmetrical leaf spring. International Journal of

Advance Materials Manufacturing & Characterization, 6(1), 51–57.

43. Arora, V., Bhushan, G., & Aggarwal, M. L. (2016) Mathematical modelling for fatigue life

prediction of a symmetrical 65Si7 leaf spring. International Journal of Computer Aided

Engineering and Technology, Vol.10, pp 287-319.

44. Arora, V. K., Bhushan, G., & Aggarwal, M. L. (2016). Precise estimation of individual leaf

camber and stepping in symmetrical 65Si7 leaf springs. Journal of the Brazilian Society of

Mechanical Sciences and Engineering, 1–13, doi: 10.1007/s40430-015-0396-3. Vol.38,issue 6,

pp1717- 29,SCI, SCOPUS.

45. Pawan Kumar and M L Aggarwal ,Shot Peening of Induction coil Hardened Spur Gear Tooth

to Avoid Failure, Vol. 2, Issue 11, November 2017 of International Journal of Modern

Science and Technology. ,Vol.7,Nov.2017 ,Vol. 2, No. 11, 2017. Page 373-376.

46. Devdutt ,M.L.Aggarwal ,Devdutt, Passenger Seat Vibration Control of a Semi-active Quarter

Car System with Hybrid Fuzzy – PID Approach, International Journal of Dynamics and

Control, Springerlink DOI 10.1007/s40435-015-0175-0, 2017, Volume 5, Issue 2, pp 287–

296,SCOPUS.

47. Krishan Kumar and M.L.Aggarwal, Optimization of various design parameters for EN45A flat

leaf springs, Elsevier Journal: Materials today proceedings, Vol.4,issue2, 2017, 1829-1836.

SCOPUS index

48. Atul Sharma, M.L.Aggarwal, Lakhwinder Singh, Experimental investigation into the effect of

noise and damping using composite spur gear, Elsevier Journal: Materials today proceedings,

Vol.4,issue2, 2017 , pp 2777-2782. SCOPUS index.

49. Arora, V., Bhushan, G., & Aggarwal, M. L. (April 2017) Enhancement of fatigue life of multi

leaf spring by parameter optimization using RSM. Journal of the Brazilian Society of

Mechanical Sciences and Engineering ,Vol. 39 issue 4, 1333-1349 SCOPUS, SCI Index

50. Pawan Kumar & M.L.Aggarwal, Comparative Analysis of Spin Induction Coil and Gas

Carburizing in Case Hardening of Spur Gear, International Journal of Advanced Technology

in Engineering and Science, Vol.5 issue 7, July 2017,pp544-552

51. Lokesh Upadhyay, M. L. Aggrawal & Pulak M. Pandey ,Performance analysis of

magnetorheological fluid-assisted electrical discharge machining, Materials and Manufacturing

Processes, Vol.33, Issue 11, 2018, pp 1205-1213, Impact factor:2.669, SCI E ,Taylor & Francis

Group.

52. Lokesh Upadhyay, M. L. Aggrawal & Pulak M. Pandey, A Review on Hybrid Electrical

Discharge Machining Processes, International Journal of Advanced and Innovative Research,

Vol. 06, Issue 12, Dec 2018,pp14-22.

53. Lokesh Upadhyay, M. L. Aggrawal & Pulak M. Pandey, Comparative Analysis of Magneto

Rheological Fluid Assisted Electrical Discharge Machining at Stationary and Rotating

Conditions of Tool, Journal of Advanced Manufacturing Systems, 2018, ISSN1793-6896 ,Vol

17,pp277-90,ESCI.

54. Pawan Kumar and M L Aggarwal, Effect of preheating on fatigue resistance of gears in spin

induction coil hardening process, IOP Conference Series: Materials Science and

Engineering, Volume 310, conference 1, 310 (2018) 012142 doi:10.1088/1757-

899X/310/1/012142,pp1-5.

55. Prince Deshwal and M.L.Aggarwal, Design and Manufacuring of shape memory alloy helical helical

spring actuator: A Riview, International Journal of Current Advanced Research,ISSN: Online: 2319-

6475, Volume 7; Issue 1(D); January 2018,pp 9208-9211 , UGC .

56. Lokesh Upadhyay, M. L. Aggrawal & Pulak M. Pandey ,Experimental Investigations

intoRotary Magnetic Field and Tool assisted Electric Discharge Machining using Magneto

Rheological Fluid as Dielectric, International Journal of Mechatronics and Manufacturing

Systems, Volume 12 ,Issue1, 2019, ISSN 1753-1047, pp1-19, Scopus .

57 Atul Sharma , M.L. Aggarwal and Lakhwinder Singh , Investigation of GFRP gear

accuracy and Surface roughness using Taguchi and Grey Relational Analysis , ISSN 1793-

6896, Journal of Advanced Manufacturing Systems, Vol. 19, No. 1 (2020) 147–165,Word

Scientific Publishers, Singapore indexed in ESCI

58 Atul Sharma , M.L. Aggarwal and Lakhwinder Singh “Optimization of cutting parameters

for surface roughness of polyamide 66/33 glass fiber composite gear using response

surface methodology”, International Journal of Research in Advent

TechnologyVolume 6, Issue 8, August 2018. E-ISSN: 2321 – 9637, pp 2074 – 2080,

(UGC Approved).

59. Suresh Kumar, M.L. Aggarwal and Lakhwinder Singh “Design and correlations of shape

memory alloy intelligent helical spring by differing the constant temperature and diameter

for a mechanical actuator”,Universal reviews, Volume VIII, Issue III, MARCH-

2019,pp461-66(UGC). 60. Kashika Aggarwal, M.L. Aggarwal and Shekhar Gupta , Oxy-Acetylene Brazing Of Al-

Cu Metal Tubesfor Minimizing Refrigeration Equipment Cost, International Journal of

Engineering Sciences Paradigms and Researches ,Vol. 48, Special Issue, (TAME-2019,

April 4-5, 2019,(An Indexed, Referred and Impact Factor Journal approved by UGC-

Journal No. 42581),ISSN (Online): 2319-6564,pp1-4.

61. Akanksha Mishra, M.L. Aggarwal , Startup Low Cost Mechatronics Product Design of a

Spring Load Tester, International Journal of Engineering Sciences Paradigms and

Researches ,Vol. 48, Special Issue, (TAME-2019, April 4-5, 2019,(An Indexed, Referred

and Impact Factor Journal approved by UGC- Journal No. 42581),ISSN (Online): 2319-

6564,pp127-129.

62. Suresh Kumar, M.L.Aggarwal and Lakhwinder Singh, Reduced weight and cost in

Smart Fork-Lift using NiTi one way helical spring, International Journal of Mechanical and Production Engineering Research and Development ISSN(P): 2249–6890; ISSN(E): 2249–8001 Vol. 10, Issue 1, Feb 2020, 483–498. Scopus

63. Suresh Kumar, M.L.Aggarwal and Lakhwinder Singh, Stability of physically-

loaded helical springs used in smart fork lift, International Journal of Engineering and

Advanced Technology Vol. 9, Issue 2, Dec. 2019,pp 3839-45

64. Suresh Kumar, M.L.Aggarwal and Lakhwinder Singh, A simple solenoid valve

SMA-based, Journal of Emerging Technologies and Innovative Research, Volume

6, Issue 6, June 2019,pp 481-85.UGC. 65. Akanksha Mishra and M.L.Aggarwal Comparative Deflection Analysis of Conical

Compression Spring With Standard Constant Rate Helical Spring, IOP Conf. Series:

Materials Science and Engineering 804 (2020) 012010,IOP Publishing, doi:10.1088/1757-

899X/804/1/012010,Indexed:Scopus,Web of Science.

66. Satyam Kumar, Vishal Puri and M.L.Aggarwal, Review of Sustainable Building

Materials for Construction Industry, International Journal of Technical Research &

Science (Special Issue), ISSN No.:2454-2024 DOI

Number: https://doi.org/10.30780/specialissue-ICACCG2020/023,Sept.2020,pp 1-8.

Indexing : Publons,Orchid, Google Scholar.

67. MOHAN LAL AGGARWAL, Dr Vishal Puri, Sh. Satyam Kumar,REVIEW OF SUSTAINABLE

BUILDING MATERIALS FOR CONSTRUCTION INDUSTRY, International Journal of

Technical Research and Science, ISSN- 2454-2024,July 2020.

68. Ravi ,M.L.AGGARWAL, “IoT Enabled Flow Measurement in Treadle Pump, Solid State Technology, Vol. 63,Issue 6, 2020,pp 22576-22583 (Scopus).

NATIONAL JOURNAL 1. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,Influence of shot peening intensity of fatigue design

reliability of 65Si7 spring steel. Indian Journal of Engg. & Materials Science, 12(6), Dec.2005, pp 515-520. Impact Factor =0.362 ,SCIE ,SCOPUS

2. M.L.Aggarwal,R.A.Khan and V.P.Agrawal , Optimization of micro welds tendency in leaf springs, Indian Journal of Engg. & Materials Science, Vol.13 (6), 2006, pp 217-220. (www.niscair.res.in) , SCIE ,SCOPUS

3. M.L.Aggarwal and P.S.Chawla, Issues in fretting fatigue design of shot peened leaf springs, Indian Journal of Engineering and Material Science,2007,pp414-418. (www.niscair.res.in) , SCIE ,SCOPUS

4. Gaurav Aggarwal,M.L.Aggarwal,’ Determine and controlling the quenching oil temperature in parabolic leaf springs industry, ISST Journal of Mechanical Engineering,Vol.1,No1,June2010,pp23-26.

5. Lakhwinder Singh,R.A.Khan,M.L.Aggarwal,’ A study of shot peening parameters of welded AISI 304 stainless steel, ISST Journal of Mechanical Engineering, Vol.1, No1, June 2010, pp27- 32.

6. M.L.Aggarwal,R.A.Khan,Lakhwinder Singh, “Replacement of solid carburizing by shot peening for 10C4 steel”.Journal of Tribology Research,Vol.1,No.1,2010,pp39-44.

.

INTERNATIONAL CONFERENCE

a. M.L.Aggarwal, shot peened high nitrogen austenitic stainless steel: an alternate to Ni rich austenitic steel for medical applications, International Conf. on Materials for Advanced Technologies, Materials Research Society Singapore,1- 6 July,2007 (Presented).

b. M.L.Aggarwal and C.K.Nagpal, Smart paint sensor: a smarter alternative to piezoelectric sensor, International Conf. on Materials for Advanced Technologies, Materials Research Society Singapore,1- 6 July,2007(Presented).

c. M.L.Aggarwal,R.A.Khan and V.P.Agrawal,Optimization of smart paint thickness in structures, ISSS International Conf. on Smart Materials and Structures, II Sc Bangalore, July 2005, pp64-71(Presented).

d. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,Smart system for measurement of compressive residual stress field in shot peened structures. ISSS International Conf. on Smart Materials and Structures, II Sc Bangalore, July 2005,pp91-97(Presented).

e. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,An evaluation of shot peening on fatigue design of discontinuously reinforced composites, International Conf. on Recent Advances in Composites Material, IT BHU, Dec. 17-19, 2004 pp 82-85(Presented) .

f. M.L.Aggarwal,R.A.Khan and V.P.Agrawal ,Effect of surface roughness on fretting

fatigue behaviour of EN-45A spring steel leaf springs,Abstract published in Int. Conf.on Theoretical Applied,Computational and Experimental Mechanics,IIT Kharagpur,Dec.28-30,2004 (Presented).

g. M.L.Aggarwal,R.A.Khan,V.K.Bansal&S.Raina,Impact of water jet peening on fatigue life of Duralcan Composite Material, Int. Conf.on Recent Advances of Composite Materials,ITBHU Varanshi,Dec.2004, pp464-67(Presented).

h. M.L.Aggarwal,R.A.Khan and V.P.Agrawal, Influence of shot peening intensity on

fatigue design reliability of discontinuously reinforced composites, Second International Conf. on Recent Advances in Composites Material, New Delhi, Feb.20-23, 2007,pp344-47(Presented).

i. Lakhwinder Singh, M.L.Aggarwal and R.A.Khan, Influence of process parameters on axial force during drilling of austenistic stainless steel – A Taguchi approach, International Conf. on Recent Development in Mechanical Engineering,SUSCET,Mohali,Punjab,Jan 2008,pp 521-25.

j. M.L. Aggarwal ,R.K.Garg,C.K.Nagpal and Gaurav Aggarwal, Design of leaf springs in automotive vehicles for weight reduction,Internatioal Conf for Prod.&Industrial Engg., CPIE 2010,pp.47-49(Presented).

k. M.L. Aggarwal and Gaurav Aggarwal, Modeling of Leaf Springs for Automation in,Internatioal Conf for Automation in Design and Manufacturing,IIT Gauhati(Presented),Dec15-16,2011.

l. Vinkel Arora, Krishan Kumar,M.L.Aggarwal and Gian Bhushan “A coparative study of standard and casted eye design of a mono leaf spring, International Conf.on recent advances in Mechanical Engineering ,Dr MGR University Chennai,April 19- 20,2011,pp.59-68.

m. M.L.Aggarwal, Modeling of Shot Peening Paramters for Weight reduction of EN45A spring Steel Leaf Springs, 2012 AASRI Confrence on Modeling,Identification and Control,Hong Kong ,3(2012),Dec.19-20,2012, pp 642-45.(Available online www.sciencedirect.com).Scopus

n. Arora Vinkel, Bhushan Gian, Aggarwal M L ,Presented a paper titled, “CAE Simulation

Approach for Static and Dynamic Analysis of Leaf Springs” in “International conference on Production and Industrial Engineering” (CPIE-2013) March 2013, pp. 143-153, organized by NIT, Jalandhar.

o. Arora Vinkel, Bhushan Gian, Aggarwal M L ,A comparative study of standard and casted eye Design of a mono leaf spring” in International Conference on Recent Advances in Mechanical Engg, June 2012, pp. 153-164 , Dr. MGR University, Chennai.

p. Krishan Kumar and M.L.Aggarwal, Optimization of various design parameters for EN45A flat leaf springs, 5th International Conf. on Materials Processing and characterization, GRIET Hyderabad, March 2016(presented).

q. Atul Sharma, M.L.Aggarwal, Lakhwinder Singh, Experimental investigation into the effect of noise and damping using composite spur gear, 5th International Conf. on Materials Processing and characterization, GRIET Hyderabad, March 2016(presented).

r. Vinkel Kumar Arora, Gian Bhushan , M.L. Aggarwal, Optimization of design, material and strength reduction factor for enhancing fatigue life of asymmetric multi-leaf

spring, 4th International Conference on Production and Industrial Engineering, Paper CPIE- 2016,161 ,pp1-14.

s. Lokesh Upadhyay, M L. Aggrawal, P M Pandey, Experimental Investigation and

Analysis of EDM with Silicon Oil as Dielectric Fluid, in Proceedings of International

Conference on ARIMPIE, Proc. Conf. at I.T.S Greater Noida, India 183-185, 2016

t. Pawan Kumar and M L Aggarwal, Influence Of Induction Hardening On Noise

Reduction And Hardness Of Sintered Alloy Steel Gear, 3rd International conference on

"Innovative Design, Analysis and Development Practices in Aeronautical and

Automobile Engineering" (IDAD 2018) to be held during 22nd-24th February

2018, Scopus indexed springer conf.

u. . Akanksha Mishra and M.L.Aggarwal Comparative Deflection Analysis of Conical Compression Spring With Standard Constant Rate Helical Spring - 8th International

Symposium on Fusion of Science and Technology, JCBUST YMCA Faridabad, Jan. 6-10,2020.

v. Sandeep and M.L.Aggarwal , Finite Element Analysis of Plain Concrete subjected

to Uniaxial and Biaxial monotonic Load, 8th International Symposium on Fusion

of Science and Technology, JCBUST YMCA, Jan. 6-10,2020.

w. Ravi Verma and Mohan Lal Aggarwal “International Conference on Research and

Innovation in Science,Engineering and Technology” IoT enabled Flow

Measurement Pump, Sept.4-5,2020. Birla Vishvakarma Mahavidyala Engineering

College,Gujarat.

x. M.L.Aggarwal, Best Paper Award Certificate: Review of Sustainable Building

Materials for Construction Industry,International Online Conference on Advances

in Computing,Communication and Green Technology,2020, Ansal University

Gurgaon,July 30-31,2020.

y Ravi ,M.L.AGGARWAL, Paper presented “IoT Enabled Flow Measurement in

Treadle Pump, International Conf. ,ICRISET ,VIDYANAR GUJARAT,Sept. 4-

5,2020.

NATIONAL CONFERENCE 1 M.L.Aggarwal,Issues in fatigue design of fretting fatigue free parabolic leaf springs in automotive

vehicles,NCAMT-2009,SMVD University,Katra,pp 190-93(Presented). 2 Lakhwinder Singh,R.A.Khan,M.L.Aggarwal,Enchancement of surface characteristics and

mechanical properties of welded AISI 304 stainless steel,,NCAMT-2009,SMVD University,Katra,pp 62-68(Presented).

3 Gulshan Sachdeva,Gaurav Aggarwal and M.L.Aggarwal, Experimental prediction of stiffness of parabolic leaf springs in automotive vehicles,NCAMT-2009,SMVD University,Katra,pp 190-93(Presented).

4 M.L.Aggarwal,V.P.Agrawal&S.Maheshwari,Effect of Shot Peening on Surface Characteristics of EN45A Spring Steel,Conf. on Development and Challenges in Manufacturing Engg. 2004,MIT Manipal,India,pp203-207(Presented).

5 Devdutt and M.L.Aggarwal, “Trends and advances in austenitic stainless steel”, National Conf.

on Trends and Advances in Mech. Engg., YMCAIE Faridabad, India, Dec.2006, pp 470-73. 6. M.L.Aggarwal,V.P.Agrawal & R.A.Khan ,Fatigue design of shot peened leaf springs, National

Conf. on Advances in Mechanical Engineering, Jamia Millia Islamia, New Delhi, Jan. 2006, pp85-89(Presented).

7. Lakhwinder Singh, M.L.Aggarwal and R.A.Khan, Softening due to case carburizing of austenitic stainless steel, National Conf. on Futuristic Trends in Mech. Engineering, SUSCET,Mohali,Punjab,Sept.2007,pp147-50,pp147-50.

8. Lakhwinder Singh, M.L.Aggarwal and R.A.Khan, Effect of shot peening and nitriding on hardness

and corrosion of AISI 304 austenitic stainless steel , National Conf. on Latest Trends in Mech. and Production Engineering RIMT-IET Mandi Gobindgarh,Punjab, June 2008,pp158-161.

9. P.N.Sandhya & M.L.Aggarwal , Particulate composite nanomaterials: manufacturing and applications ,National Conf. on Futuristic Trends in Mech. Engineering, SUSCE,Mohali,Punjab,Sept.2007.

10 Lakhwinder Singh,R.A.Khan,M.L.Aggarwal,K.Gaurav and Gaurav Aggarwal, Effect of double shot peening on surface characteristics of welded AISI 304 stainless steel, National Workshop on

Materials Processes,IT BHU,Varanshi,May,2009 pp 31-37. 11. M.L. Aggarwal and Gaurav Aggarwal, Modeling of Leaf Springs for Automation in,Internatioal

Conf for Automation in Design and Manufacturing,IIT Gauhati,Dec15-16,2011

12 Lakhwinder Singh, M.L.Aggarwal and R.A.Khan, Damping factor modulation by shot peened AISI 304austenitic stainless steel”,National Conf on Tribology of Automotive Systems,11-12 Dec.2009,IIT New Delhi,pp121-24.

13. Vinkel Arora, M.L.Aggarwal and Gian Bhushan “A comparative study of standard eye and riveted eye design of a mono leaf spring ,National Conf. on Emerging Trends in Mechanical Engg.,2012,pp49-55.

14. Lakhwinder Singh, R.A. Khan, M.L. Aggarwal, Manmohan Kakkar, “Optimization of surface hardness and Impact strength of welded AISI 304 stainless steel”, FTME-2010, National Conference GNE Ludhiana, Oct. 2010, pp 48-54.

15. Devdutt &M.L.Aggarwal, Fuzzy Control Of Semi Active Quarter Car Suspension System With MR Damper, TAME 2012 at YMCAUST, FARIDABAD, Oct.19-20,2012.

16. Atul Sharma & M.L.Aggarwal ,Deflection And Stress Analysis Of Brake Disc Using Finite Element Method, TAME 2012 at YMCAUST, FARIDABAD, Oct.19-20,2012.

17. M.L.Aggarwal, Shot peening for modifying surface properties of leaf springs, National Conference on Advances in Material Sc for Energy Applications, UPES Dehradun, Jan 9-10, 2014(Presented).

18. Sachin Dhull M.L.Aggarwal, Automation in material handlimg system using solar energy for light load applications,4th National Conf. on “Recent Advances in Manufacturing” June 2014, pp 202-206.

19 Devdutt, M.L. Aggarwal, “Hybrid Fuzzy-PID Control of a Semi-Active Quarter Car System”,

Proceedings of the National Conference on Paradigms in Mechanical Engineering, Manav Rachna

International University, Faridabad, Haryana, 5 pages, Dec. 20, 2014. 20 Sonu Yadav,M.L.Aggarwal, Sustainable Design of Automated Toggle Screw Jack for Lifting

Automotive Vehicles ,National Conf. on Sustainable Manufacturing ,Jan 2-3,2015 ,MNIT Jaipur, pp 145-48.

21 Atul Sharma,M.L.Aggarwal and Lakhwinder Singh, Study of feed on gear performance manufactured with shaper, National Conf. NCAME-March 2016,BSAITM,Faridabad

22 Atul Sharma,M.L.Aggarwal and Lakhwinder Singh,An investigation for cutting parameters for shaper to reduce noise of composite gears, National Conf. RSTTMI-March 2016,YMCAUST Faridabad.

23 Vinkel Kumar Arora, Gian Bhushan , M.L. Aggarwal, “Desirability approach in RSM applied to

symmetrical multi leaf spring” , 3rd National conference on Trends and Advances in Mechanical

Engg. ISBN 978-93-5268-269-0 , March 16-17,2017 ,pp151-157. 24 Vimlesh Kumar Ojha, M.L.Aggarwal “ Hydrogen: Future Fuel For Engines” 3rd National

conference on Trends and Advances in Mechanical Engg. ISBN 978-93-5268-269-0 , March 16-

17,2017 , pp 1-4.

25 Krishan Kumar, M.L. Aggarwal, Sustainable Design Of Composite Parabolic Leaf

Springs. 3rd National conference on Trends and Advances in Mechanical Engg. ISBN 978-93-

5268-269-0 , March 16-17,2017 ,pp116-119.

26. Atul Sharma, M.L. Aggarwal, Lakhwinder Singh, Noise Reduction Using Glass Fiber

Reinforced Polymer Gear, 3rd National conference on Trends and Advances in Mechanical

Engg. ISBN 978-93-5268-269-0 , March 16-17,2017 ,pp200-202

27. Lokesh Upadhyay, M L. Aggrawal, P M Pandey, Magneto Rheological Fluid Assisted

Electrical Discharge Machining, 3rd National conference on Trends and Advances in

Mechanical Engg. ISBN 978-93-5268-269-0 , March 16-17,2017 ,pp 243-49.

28. Sarika Gupta, M.L.Aggarwal, Solar Operated Sand Molding Compaction Process, 3rd

National conference on Trends and Advances in Mechanical Engg. ISBN 978-93-5268-269-0 ,

March 16-17,2017 pp 263-67.

29 Kashika Aggarwal, M.L. Aggarwal, Shekhar Gupta,oxy-acetylene brazing of al-cu metal

tubes with flux cored filler wire for cost reduction in refrigeration industry,TAME-7, 4th

National conference on Trends and Advances in Mechanical Engg.,April 4-5,2019,JCBUST

YMCA,Faridabad.

30. Akanksha Mishra, M. L. Aggarwal , Startup Low Cost Mechatronics Product Design Of

a Spring Load Tester, 4th National conference on Trends and Advances in Mechanical

Engg.,TAME 55, April 4-5,2019,JCBUST YMCA,Faridabad.

31. Startup Low-Cost Mechatronics Product Design of A Spring Load Tester – National

Conference On Trends and Advances in Mechanical Engineering (TAME 2019)

Patent:

Patent application No.

Filing /Publication Date

Title Applicant

201911015672 Filing:18-4-2019,

Publication-The

Patent Office

Journal No.

43/2020 Dated

23/10/2020 ,pp

54483

Stiffness

measurement of

walnuts, method

and its use

Prof. M.L.Aggarwal

Ms. Akanksha Mishra(M.Tech.student)

202011014493 Filing:1-4-2020,

Publication: The

Patent Office

Journal No.

10/2021 Dated

05/03/2021 11063

Urban rain water

harvesting and its

monitoring

Prof. M.L.Aggarwal

Mr. Ravi Verma(M.Tech.student)

202011015782 11-4-2020 System for Mobile

Decontamination

Chamber

Prof. M.L.Aggarwal

Dr Krishan Kumar

i10,h index

Google Scholar: i10=18, h=12,citation 560

Scopus: i10=9, h=8, citation=168

WoS- h=5, number of paper=16, citation=85, i10=1

Training/STC/ Workshop 1. MAY 22-26, 2006, MECHATRONICS, NITTTR CHANDIGARH 2 JUNE 14-23, 2006, PRO-E, ROLTA INDIA LTD., YMCAIE FARIDABAD 3 JUNE 26-28, 2006, PROJECT MANAGEMENT, NITIE BOMBAY 4 JULY 12-13, 2006 MECHATRONICS, CYBERTECH (P) LTD., YMCAIE FARIDABAD 5 JAN.20-21, 2006, MECHANICAL ENGG, JAMIA MILLIA ISLAMIA NEW DELHI 6 JULY 28-30, 2005, SMART MATERIALS, II Sc BANGALORE 7 DEC.28-30, 2004, EXPERIMENTAL MECHANICS, IIT KHARAGPUR 8 DEC.18-20, 2004, COMPOSITE MATERIALS, IT BHU, VARANSHI 9 MARCH 18-20, 2006, MANUFACTURING ENGG.-2004, MIT MANIPAL 10 3 DAYS APRIL, 2004, FINANCIAL STATEMENTS, NIFM FARIDABAD 11 Attended 16 weeks Short Term Courses at IIT New Delhi, IIT Kanpur, IIT Roorkee, NITTTR

Chandigarh, REC Jaipur, and CEDT Mohali. 12. Attended ICT based STC of NITTTR Chd. Dec.15-19,2014 and June 8-12,2015. 13. Attended ICT based STC on “Communication Skill” of NITTTR Chd. 11.1.2016- 15-1-2016 and

7/7 to 11/7/2014. 14. Attended ICT based STC on “Research Methodology” of NITTTR Chd. 6.6.2016- 17.6.2016 .

15. Attended workshop on ‘MIG/MAC Welding and its variants’ , IIT Delhi, Jan. 19-20,2018.

16. STC ‘ Curriculum Implementation’ Oct. 8-12,2018, at YMCAUST Faridabad through NITTTR

Chandigarh

17. International Workshop ‘Nano/Micro 2D-3D Fabrication ,Manufacuring of Electronic –Biomedical

Devices and Applications, 31-10-2018 to 2-11-2018,IIT Mandi

18. FDP, Crystallography in Material Sc, IIT Delhi, June 24-28,2019

19. STTP, Convener, Recent Trends in Civil Engg.,Nov.13-17,2019, REC Ambedkar Nagar(UP)

20. Participated Workshop “ Author’s Workshop” , Indian Socity of Mechanical Engineers, IIT Delhi,

Dec.23,2019.

21. Participated Workshop” An Insight into Revised Accreditation Framework of NAAC” NAAC

Sponsored,JCBUST YMCA Faridabad,Feb.12,2020.

22. Participated one week TEQIP Workshop/ STC “ Hands - on Training on IOT Modules,JCBUST YMCA

Faridabad, Feb.24-29,2020.

23. Applied MOOC Course hosting , Feb.2020.

24. 2 Week STC TEQIP3 Online course , Digital Transformation in Teaching and Learning Process, Feb.14,2020

– March 6,2020,NPTEL.

25. Two Week STC TEQIP3 Online course ,Green Energy Techologies for Sustainable Development,June11-

20,2020,NIT Kurukshetra.

26. One Week STC TEQIP3 Online course, Technological Industrial Practices,June1-6,2020, JCBUST

YMCA Faridabad.

27 One Week STC TEQIP3 Online course, Additive Manufacturing with Interdisciplinary Applications, June

29- July 3,2020, NIT Jalandhar. 28. One Week STC TEQIP3 Online course, One Week STC TEQIP3 Online course, “Green

Technologies and Environmental Sustainability (GTES-2020)”, Sept. 7-12,2020, JCBUST

YMCA Faridabad

29. One Week STC TEQIP3 Online course, “Control Guidance and Estimation of Flight Vehicles,

Sept. 11-16,2020, NIT Kurukshetra.

30 Webnair attended: Vocal for Local,State Technical Instituition,Nelokheri,Oct.2,2020,

31. “Internet of Things: Industry, Academia & Start-ups” TEQIP online Workshop organized

at IIT Hyderabad between December 21 - 23, 2020.

32. Robotics and Automation, 2 week FDP AICTE Sponsored, JMI Delhi, June 16-30,2021

Chairman Conf. 1. Session Chair , Science Conclave-2014,April 16-17,2014, YMCAUST Faridabad

2. Session Chair, STC Prog. ,Effective Teaching and Research,7/7/14 to 11/7/14,YMCAUST

3. Session Chair, Industry-Instuition Interaction ,National Conf. on Role of Sc &

Technology,towards”Make in India” ,March 5-7,2016.

4. Session Chair, Design, National Conf., TAME, YMCAUST, 2012.

5. Session Chair: Symposium on Nanotechnology: Interdisplinary aspects, Dec.1,2012

,YMCAUST Fbd.

6. Session Chair , National Conf. RSTTMI , March 5-7, 2016,YMCAUST Faridabad.

7. Session Chair , 4th International Conference on Production and Industrial Engineering, Paper

CPIE- 2016 ,Material and Processing, , NIT Jalandhar, Dec. 19-21, 2016,

8. Session Chair , National Conf. NHTSEE, March 9-10, 2017,YMCAUST Faridabad.

9. Conference Chairman : 3rd National conference on Trends and Advances in Mechanical Engg.

ISBN 978-93-5268-269-0 , March 16-17,2017

10. Co-Chairman-National Conference on :En Energy & Sustainability: Sources, Expectations &

Uncertainties, Aggarwal College Ballabhgarh, Haryana, March 9-10,2018

11. Special Training Program for Civil Engg. students arranged with NCB , Jan 7-11,2019.

12. Program Chair: Workshop for Civil Engg Students in association with Aimil Limited on Feb.

11-12 ,2019 and March 13-14,2019 at JCBUSTYMCA Faridabad.

13. Sesson Chair, 4th National conference on Trends and Advances in Mechanical Engg., April 4-

5,2019,JCBUST YMCA,Faridabad.

14) Sesson Co-Chair, 8th International Symposium on Fusion of Science and Technology, JCBUST

YMCA Faridabad, Jan. 6-10,2020.

15. Conducted and Speaker in one Days TEQIP-III Workshop on BIS Guidelines for

Construction February 13,2020

16. Program Chair, Five- Day Workshop on Trends and Advances in GIS and

Surveying in Civil Engineering,JCBUST YMCA,January 13-17,2020

17. Convener, one Week STC TEQIP3 Online course, Technological Industrial Practices,

June1-6,2020, JCBUST YMCA Faridabad.

18. Member Advisory committee, Research in Modern Era,June1- 5,2020, ME Department,

JCBUST YMCA Faridabad.

19. Convener, One Week STC TEQIP3 Online course, One Week STC TEQIP3 Online course,

“Green Technologies and Environmental Sustainability (GTES-2020)”, Sept. 7-12,2020,

JCBUST YMCA Faridabad

20. Program Chair, Five Days TEQIP-III Twinning FDP ,Safety Engineering, Oct. 12-

16,2020, Civil Dept., JCBUST YMCA Farodabad.

21. Convener , TEQIPIII Twinning Webinar, ICT for Students and Teachers,2.11.2020,organized

by Faculty of Engg.& Technology,Faridabad

22. Convener , TEQIPIII Twinning Webinar, Patents and Innovation,2.11.2020,organized by Civil

Engg. Department, Faridabad

Company/ Instt. Purpose

1 Visit of Talbros Automotive Components Ltd.

Faridabad on 6.12.2019 alongwith DSIR Officials

Sh. N.K.Gupta, Sh.Pratap Singh, Scientist

E.Lecture to Sr Executive regarding R&D

R&D Centre

2. Bony Polymer Ltd. Faridabad, 5.2.2020 R&D Centre for reaserch work

3 Super Auto India Ltd. ,Lecture Jr

Enr.,11.10.18,Sector-6, Faridabad

Visit alongwith students

Consultancy

1. Prof. M.L.Aggarwal completed consultancy work 2019-20 on “Compresion

Testing of Materials”. Amount of Rs. 1,44,000/- (1.44 lakh) was received from

Executive Engineer Panchayat Raj , Gurgaon.

2. Rs. 24000/- consultancy work completed in 2020-21 from Executive Engineer

Panchayat Raj , Gurgaon for testing materials of Teekli Community Centre.

3. Feasibility of Welding Cu-Al , Ador Welding Ltd, Sept.2018 - March 14, 2019,

Rs. 50000/- consultancy.

4. Filling of Badkhal Lake from CITM1 to CITM2, Jan.-March 2017, Rs. 5000/-

consultancy was received from PWD Irrigation and water resource Dept.Faridabad

5. Team Leader in 17 Miscellaneous construction project consultancy value Rs. 45.0

lakh during Dec.20 to August 21.

Project Applied

1.Modular Solar Operated Improved Design to Avoid Tiresome Operation of the Human-

operated Treadle Pump for Irrigation in Villages dstharyana@gov.in, S.N.- 397,

July 2020

2. Rs. 14,11,764 received for MODROB project titled” Modification of Welding Lab by removing Obsolete machine and adding latest welding machines,20.7.2020.Funding agency AICTE MODROB. Application Number:200708124127

Awards !) M.L.Aggarwal,Fatigue Design Engineer,Pub.in Who is Who in Science and Engineering,Sept.2006,9th,USA . !!)Appreciation award by Director YMCAIE Faridabad for publication in INTERNATIONAL JOURNAL, year 2007, 2008, 2009. !!!) Best paper presentation award in National Conf. at MIT MANIPAL, 2004. iv) Best paper presentation award , National Conf. TAME,YMCAUST Faridabad, 2012. v) Best paper presentation award , International Conf. on Advances in computing,Communication and Green Technology,Ansal University, July 30-31, 2020.

vi) Certificate of Best Upcoming Civil Engg. Department,by Vice-Chancellor J C BOSE

UNIVERSITY of SC.& TECHNOLOGY Faridabad, 2019-20, Sept.16,2020

Reviewer

1. Reviewer papers of Elsevier publications, IJ FATIGUE– 2006 onwards.

2. Reviewer paper I.Mech.E. UK, Journal of Engg. Manufacturer, 2007 onwards.

3. Reviewer paper Int. J.of computational methods, 2008 onwards.

4. Reviewer of Elsevier publications,Jof Materials Processing Technology, 2009 onwards.

5. Reviewer paper of Elsevier publications, J Material Processing, 2010 onwards.

6. Reviewed three papers for International Conf., CPIE 2010 held at NIT Jalandhar.,

7. Reviewed papers , International Journal of Vibration and Control, 2016-2017.

8. Reviewer papers ,Journal of engineering science and technology review,March 2017

onwards.

9. Ms. Ref. No.: APSUSC-D-17-05880. Applied Surface Science, 9-6-2017

10. Journal of Mechanical Engineering Sciences (JMES), May 30,2018. JMES1803099

11. International Journal of Automotive and Mechanical Engineering, Nov.2018.

12. The Walailak Journal of Science and Technology, Institute of Research and Innovation, Walailak University, Thasala,

Nakhon Si Thammarat 80161, Thailand,journal.wu@gmail.com,2020

13. International Journal of Industrial and Manufacturing Systems Engineering,2020,ISSN Online:

2575-3142 ISSN Print: 2575-3150

Membership MIE M-1526949 Institution of Engineers (I) 2015 LM 107592 ISTE New Delhi 2015 Member : Boiler Board Haryana Member: HSTES Panchkula, 2011 onwards NBA Committee Member for accreditation,2016 onwards Member: District committee headed by DC for Surajkund Kraft Mela (2015-17).

Expert Lecture

1. M.L.Aggarwal, Expert Lecture, Industry Institute Interaction for improvement of quality in ET Education,Dec.25, 2015, TEQUIP Sponsored FDP Prog.,DCRUST Murthal.

2. M.L.Aggarwal, Expert Lecture, Fatigue Design of Leaf Springs, March 21,2016,UG/PG Students, NIT Jalandhar.

3. M.L.Aggarwal, Expert Lecture, Innovation and Effective Teaching, July 9,2014,ISTE approved FDP Prog. Organized at YMCAUST Fbd.

4. M.L.Aggarwal, Expert Lecture, Entrepreneurship: An effective tool to improve Industry-Institute Interaction , Dec.13(AN) in Dec. 7-20, 2017, YMCAUST Faridabad.

5. Invited talk: Low Cost Solar Power Utility for Poor Person, Aggarwal College Ballabhgarh in National Conf.,9-3-2018

6. Expert Lecture-Advances in Materials, GEC Raipur, 23-05-2018.

7. Expert Lecture: Mechatronics with MATLAB, GPW Faridabad,29-08-2018. 8. M.L.Aggarwal, Expert Lecture, Entrepreneurship: An effective tool to improve Industry-

Institute Interaction , 28-01-2019, FDP : JCBUSTYMCA Faridabad.

9. M.L.Aggarwal,Roof Top Water Harvesting,Invited Talk in STTP,REC Ambedkar Nagar

(UP),Nov.17,2019

10. M.L.Aggarwal, Engineering Materials,Invited Talk in STTP,REC Ambedkar Nagar

(UP),Nov.16,2019

11. M.L.Aggarwal, Expert Lecture; How to improve Industry-Institute Interaction , 02-06-2020,

FDP : JCBUSTYMCA Faridabad.

12. M.L.Aggarwal,Expert Speaker ,Effective use of ICT for quality learning, ICT FOR PRE-

SERVICE TEACHERS,IN-SERVICE TEACHERS &TEACHER EDUCATORS,Webinar

jointly organized by NEHU Shillong and NIT Jalandhar,Oct..21,2020

13. Speaker: Importance of AutoCAD for Architectural Drawing: 2 days State Level

Workshop,CAD/AutoCAD and Pond Architectural Drawing, August26-27,2020.

14. Expert Speaker online:National Webinar for ‘ ICT for Pre-Service Teachers, In-Service

Teachers and Teacher Educators, Oct.21,2020, 4 to 5pm. North Eastern Hill University

Shillong & NIT Jalandhar.

Ph D Scholars Guided by Prof. M.L.Aggarwal

S.N. Name

(Regn. University)

Supervisor Title Regn /Completion

status

1 Dr Vinkel Arora

(NIT K)

Dr Gian Bhushan

(NIT K)

Dr M L Aggarwal

(YMCAUST)

Structural Analysis of Leaf

Springs using CAE tools

Nov.2010-March

2017.Completion

notification on

31.3.2017.

2 Krishan Kumar

(YMCAUST)

Dr M L Aggarwal

(YMCAUST)

Computer aided engineering

analysis and optimization of

conventional leaf springs

May 2011-

Nov.2016

Completion

notification on

29.11.2016.

3. Devdutt

(YMCAUST)

Dr M L Aggarwal

(YMCAUST)

An investigation of

effectiveness and damping

capabilities of hydraulic shock

absorbers.

May 2011 –April

2016. Completion

notification on

1.4.2016.

4. Lakhwinder Singh

(JMI N Delhi)

Dr R A Khan (NIT K)

Dr M L Aggarwal

(YMCAUST)

Effect of shot peeing on

mechanical properties of

austenitic stainless steel

Oct.2007 –

Dec.2012.

Completed.

5 Lokesh Upadhyay

(YMCAUST)

Dr M L Aggarwal

(YMCAUST)

Dr P M Pandey,IIT Delhi

Experimental investigations

and analysis of

magnetorheological fluids

based electric discharge

machining process.

Feb.14,2013-

Completion

notification on 15-

10-2018 .

6 Suresh Kumar

(YMCAUST)

Dr M L

Aggarwal(YMCAUST)

Dr Lakhwinder

Singh(YMCAUST)

Stress Evaluation Technique

Of Helical Spring With

Modified Design Parameters

Pre-Ph D submission

meeting held on

3.3.2020 and Thesis

submitted.

7. Atul Sharma

(YMCAUST)

Dr M L

Aggarwal(YMCAUST)

Dr Lakhwinder

Singh(YMCAUST)

Comparative analysis of metal

matrix composite and fibre

reinforced polymer for a gear

Feb.14,2013,

Completed Feb.27,

2020.

M.Tech Thesis/ B.Tech. Projects

S.N. Project Title Student Name Supervisor

x “ IoT Enabled Flow Measurement

in Treadle Pump”

Ravi

(19001517018),Dec.2020

M.L.AGGARWAL

y IOT based Treadle Pump

Ravi

(19001517018),May

2020

M.L.AGGARWAL

z Development of Lateral Bump Stop

for EMU (railways)

DEEPAK SHARMA

(18001517004),May

2020

M.L.AGGARWAL

A1 Testing And Analysis Of

Variable Spring Stiffness Under

Varying Test Conditions

Akanksha Mishra,Roll

No. 18001517002 (2018

Batch), Dissertation in

Dec. -2019

M.L.AGGARWAL

A LOW COST MECHATRONICS

PRODUCT DESIGN OF A SPRING

LOAD TESTER

Akanksha Mishra,Roll No.

18001517002 (2018

Batch),project in May -

2019

M.L.AGGARWAL

B REDUCTION OF CUTTING FLUID

CONSUMPTION IN A GRINDING

OPERATION

Bhupender Singh(2017

batch),M.Tech.Dissertation-

May 2019

M.L.AGGARWAL

C OXY-ACETYLENE BRAZING OF

AL-CU METAL TUBES WITH FLUX

CORED FILLER WIRE

Kashika Aggarwal,M067-

2017,Project

Dr M.L.Aggarwal

D

FABRICATION OF TREATMENT BY

INDUCTION HARDENING

ABHINANDAN GARG (M-

2243-2KI4) GAUTAM

GOYAL (M-2270-2K14)

SHIVAM (M-2338-2K14)

VINIT JINDAL (M-2354-

2K14) VIPIN (M-2355-2K14)

Dr M.L.Aggarwal

E MODELING AND EXPERIMENTAL

ANALYSIS OF SHAPE MEMORY

ALLOY HELICAL SPRING(2016-18)

PRINCE

MM-826-2KI6

Dr M.L.Aggarwal

1 M.Tech.

Ms Sarika Gupta

(MM673-2K15)

(Jan-May 2017)

Creating a common

standard matrix tool for

mapping of product

associated standards used in

refrigeration industries

Dr M.L.Aggarwal

MVSN Kiran Kumar

Sr Manager, Danfoss

Industries India P Ltd

2 Sachin Gupta(MM474-2K14)

(Jan-May 2016)

Interfacing of various

components in solat

operated robot

Dr M.L.Aggarwal

3 Sonu Yadav(MM275-2K13)

(Jan-May 2015)

Solar energy driven

automated screw jack

Dr M.L.Aggarwal

4 Sachin Dhull(MM75-2K12)

(Jan-May 2014)

Automated material

handling system using solar

energy for light weight

applications

Dr M.L.Aggarwal

5 Ashutosh

(Jan-May 2012)

Computer aided analysis of

involute gear for various

materils

Dr M.L.Aggarwal

6 Deepak Singatia

(Jan-May 2012)

Computer aided analysis of

flat pulley for various

materials

Dr M.L.Aggarwal

7 Nitin Aggarwal

(Jan-May 2011)

Computer aided

calculations of design

parameters of closed coil

helical springs

Dr M.L.Aggarwal

8 Lalit Kumar,MTM 2506-2K8

(Jan-May 2010)

Mechatronics system design

for controlling pumps

Dr M.L.Aggarwal

9 Ishwer Das,MTM 2505-2K8

(Jan-May 2010)

Pallet design and its

automation for processing

components in a CNC

machining centre

Dr M.L.Aggarwal

10 Vishal Kumar, MTM 1741-2K16

(August-Nov.2007)

Rollers for taper leaf springs Dr M.L.Aggarwal

11 Vishal Kumar, MTM 1741-2K16

(Jan-May 2008)

A stress approach model for

predicting fatigue life of

parabolic leaf springs

Dr M.L.Aggarwal

12 P N Sandhya

(August-Dec 2007)

Particulate composite nano-

materials-manufacturing

and applications

Dr M.L.Aggarwal

13 Anmol Kaul,M Tech.112-2k4

(Jan-May 2006)

Analysis of thread rolling

flat dies

Dr M.L.Aggarwal

14 Rajeshwar Sahai,M.Tech.1215-2k3

(Jan-May 2006)

Shot peening as a substitute

of liquid carburizing for

10C4 non machined steel

Dr M.L.Aggarwal

15 Manoj Kumar Nayak,M Tech 1209-2k3

August -Dec 2004

Just in time inventory model

for rotomoulding machines

Dr M.L.Aggarwal

16 Sandeep Gupta,M.Tech.1217-2k3

(Jan-June 2005)

Avoidance of bearing

failurethrough reliability

centred maintenance

Dr M.L.Aggarwal

17 Tajinder Singh,M.Tech.756-2k5

(August-Dec 2006)

Condion monitoring

through sensors

Dr M.L.Aggarwal

18

Peeyush chaudhary M1718-

2K13,Peeyush Yadav M1719-2K13

Rahul Dubey M1726-2K13,Deepak

M1675-2K13,Chirag Kataria M1671-

2K13

(Jan-May 2017)

Solar operated bicycle

Dr M.L.Aggarwal

19 Bijender Singh M1173-2K12,Manoj

Tanwar M1199-2K12,Chirag Yadav

M1176-2K12,Monu M1205-2K12

(Jan-May 2016)

Estimating for filling

Badkhal lake from CITM1

abd CITM2(by lifting)

Dr M.L.Aggarwal

20 Prateek Mangla M776-2K9,Sahil Goel

M790-2K9,Shubham Agrawal M798-

2K9,Lalit Taneja,M754-2K9

(Jan-May 2013)

Increasing the efficiency of

an air-conditioner

Dr M.L.Aggarwal

21 Kapil Sharma,M1089-2K3,Prabhav

Azad,M1095-2K3,Rahul

Yadav,M1098-2K3

To study design

considerations of heat

treatment process

M.L.Aggarwal

Dr Sanjeev Goyal

22 Deepak Singathia,M1087-2K3,Gaurav

Indora,M1088-2K3,Manjeet

Kumar,M1092-2K3,Prem

Pujari,M1096-2K3

Impact of EDM on various

properties of metals

Dr M.L.Aggarwal

Administrative duties 1.) Project Coordinator,UG/PG,2006-08.

2.) M.Tech.Coordinator, Mech.Engg.Deptt.,2006-06

3.) Class Test Coordinator, Mech. Engg.Deptt., University Exam Centre Supdt.(7 times),2006-2010

4.) Nodal officer finance, TEQIP Activities,2006-08

5.) State Public Information Officer,YMCAUST FBD, Jan.2, 2010 – August 2,2013

6.) Dean Academic Affairs,Feb. 21, 2011 - May 11, 2014

7.) Chairperson (ME), May 12, 2014 – May 11,2017.

8) Chairman Admission committee B.Tech. physical counseling 2016.

9) Chairman Vice-Chancellor Gold Medal committee for UG/PG 2016-17

10) TEQIP Coordinator, Jan – May 2017 YMCAUST Faridabad

11) Chairman Civil Engg., May 14,2018 onwards

12) Chairman CPC , April 7,2019 onwards.

13) BOS Chairman Civil & FAE, August 2017 onwards.

14) Dean Faculty (E&T), May 2020 onwards.

BOOKS/ THESIS PUBLISHED 1. Energy Saving Opportunities, Fuels and Lubricants, Engineering Drafting AICTE Sponsored for

continuing education,1994.

2 M.L.Aggarwal, Impact of shot peening parameters on fatigue life of leaf springs, M. Tech.Thesis, Mech.

Engg. Deptt., IIT New Delhi, 2003.

3 M.L.Aggarwal, Effect of shot peening parameters on fatigue life , Ph.D.Thesis, Mech. Engg. Deptt., JMI

New Delhi, 2006.

4. Design Data Book(For Mechanical Engg. Students &Working Professionals), Jain Brothers

Publications,16/873,East Park Road, Karol Bag,New Delhi-110005,ISBN: 978-81-8360-186-3,2013.

5. Engineering Graphics and Machine Drawing, ISBN: 978-81-7700-214-0, B.Tech. ,Dhanpat Rai &

Sons, New Delhi, 2017

6. Editor, 3rd National conference on Trends and Advances in Mechanical Engg. ISBN 978-93-

5268-269-0 , March 16-17,2017

7. Advances in Environmental Science & Engineering, 978-93-90847-18-1,Feb.2021, Kripa-

Drishti Publications,Pune,INDIA

Events Conducted as Chairman(ME) : 2014-15

S.N Seminar/STC

/FDP/

Workshop/

other

Conducted

Title Date/Duration

Organized by

Department.

1. ISTE

Approved

FDP

Effective Teaching &Research July 7-11,2014

2. Seminar in

collaboration

with JCB

Industry

Campus to Corporate Life 29-08-2014

3 Engineer’s

Day

Celebration

Quiz Context 15-09-2014

4 Seminar Saksham Bharat and Sikshit

Bharat

17-11-2014

5 ICT Based

STC

I.C.Engines Dec 15-19, 2015

6 Workshop Updating/Modification of UG/PG

Syllabi

Dec.23,2015

7. Seminar Philosophy of Make in India

20-01-2015

8. Workshop in

association

with YUVA

Motors

Overhauling of 4-Stroke Engines

(60 student participants)

Feb26-27,2015

9. Foreign

Delegation

Visit from

Malaysia

Interaction with students and

Faculty. Presentation of Award

&certificate to Sh. Naveen Kumar

of YMCAUST for AI rank 30 in

GATE 2015 at National Level.

10-04-2015

10 ICT Based

STC

Technical Teachers ,Role, Self

Esteem Motivation and

Professional Development

June 8-12,2015

Events Conducted as Chairman(ME) : 2015-16

S.

N.

Seminar/STC/FDP/

Workshop/other

Conducted

Title Date/Duration

1. Teacher Day Celebration by

M. Tech. Students

Teacher Day September 5,2015

2. Seminar in Robo Edubotix

Lab

Solid Works Applications in ME 11-9-2015 to 14-09-

2015

3 Danfoss-YMCAUST Centre

of excellence Inauguration

by Denmark Ambassador:

Mr. Peter Taksoe-Jensen.

Inauguration of Centre of Excellence on

“Climate and Energy” and Project Exhibition

Nov.2,2015

4 ICT Based STC Communication Skills Jan.11-15,2016 (34

participants certified

through NITTTR Chd )

5 Service to Community Mechanical Inspection of Suraj Kund Kraft

Mela-2016

January 30 to Feb.

15,2015(Chairman ME :

Member of DC Fbd

Committee for Mech.

Inspection)

6. Service to Community (Free

Computer Education)

Basic Course in Computer Education Feb 23 to March 6,2016

(23 participants)

7 Innovative Vehicle

Demonstration by SAE

Club/MechNext Team in

YMCAUST

All-terrain vehicle for ATV Championship-

2016 at IIT Bhuvneshwar

Feb.24,2016

8 Expert Lecture by Sh.

Ravichandran

Purushothaman, Danfoss

President India

Energy Efficiency in Refrigeration System Nov.2,2015

9 Expert Lecture by Sh.

G.D.Sharma,VP Stantest

India(P) Ltd

Quality Control and Lab Testing March 9,2016

10 Expert Lecture by Sh.

A.K.Nehra,MD , Belz

Instuments Ltd

Metrology and Measurements March 18,2016

11 Expert Lecture by Sh.

Chander Saksraran, DGM,

IOC

Metallurgy of Materials March 31,2016

12. Academic Excellence

Awards to topper of All India

Competitive Exam.

Presentation of Award &certificate by Vice-

Chancellor,YMCAUST to the following

students:

1.Vipin Aggarwal, M1260-2K12,

53- Rank GATE-2016

2. Laveena Saxena, M1196-2K12, CAT

percentile 98.94%.

3. Adhyyan Malik, M1144-2K12, IIFT

percentile 99.5

March 31,2016

13 National Conference on Role

of Sc & Tech towards” Make

in India”

Theme: Recent Projects and Innovations in

Mech. Engg.

March 7,2016 (41

papers)

14 Training Prog.in Centre of

Excellence

Training on Refrigeration Trainer Kit by

Danfoss official

29-04-2016

Events Conducted/Organized in ME Deptt. (2016-17) S.N

.

Seminar/STC/FDP/

Workshop/other

Conducted

Title Date/Duration

1 ISTE approved one week STC at Mechanical

Engineering Department YMCA UST Fbd

“MATLAB AND SIMULINK”

Certified by MATHWORKS.

18th – 22nd July, 2016

2 Visit of Sh. Jawa, MD Daikin Air-

conditioning I Pvt Ltd, Sh.Vikas

Gupta,Regional Manager-North, Sh. Anupam

Chauhan Director,Better Comfort Systems

Delhi and others in ME Deptt.

Inauguration of YMCAUST-DAIKIN

,Centre of Excellence in RAC

Workshop

3-8-2016

3 Visit of Sh. Anil Kumar Khera ,Director The

Leadership Watch, Sh.Sunil Bajaj ,Head

Technical Services L&T in ME Deptt.

Industry Institute Interaction 6-8-2016

4 Project exhibition organized by ME Deptt. in

Danfoss Centre of Excellence, YMCAUST

Fbd

Innovation to Entrepreneurship

22-8-2016 to 23-08-2016

5 Danfoss officials visited the ME Deptt. for

Industry Instt.Hareesha HRM,MNSV Kiran

Danfoss Innovator Award 23-08-2016

Kumar Senior Manager RD & E,Hareesha

Setty,Sr Engineer.

6. Teacher Day Celebration by M. Tech.

Students

Teacher Day September 5,2015

7 Refrigeration Workshop ,Danfoss

COE

Testing and Measurement in

Refrigeration

Oct. 20-21,2016

8 National Conference : TAME2017 3rd National Conference on

“Trends and Advances in

Mechanical Engineering”

March 16-17,2017

Expert Lecture in ME Deptt. (2016-17) S.N

.

Expert Lecture Conducted Title Date

1 Ankit Tripathi, Technical Head

ni logic P Ltd

3D Printing 10.8.2017

2 Mr Parag Kavethkar,STM (Notrhetn

Region),Bosch Ltd. Delhi

Recent Advances in Automobiles” 19-8-2016

3 MNSV Kiran Kumar,RD&E, Danfoss

Industries P Ltd,Tamil Nadu

Energy Efficiency in Refrigeration

Systems”

22-08-2016

4 Expert Lecture by Er Deepak Verma,

Manager Global Operations, Danfoss

Industries P Ltd

Refrigerants Oct.20,2016

5 Expert Lecture:

By Puneet Goswami,

FARO Business Tech P Ltd

Coordinate measuring machine 23/1/2017

6 Expert Lecture

Kabilesh kumar,Sr Manager

New Refrigerants 17/2/2017

7 Expert Lecture:

DDN Verma , GM NTPC(Retd),GM Dee

Piping Industries , Prithla

Advaces in Welding

7/3/2017

8 Dr Kannan C , DGM ,IOC Faridabad Scope of research on Petroleum

Products

16/3/2017

9 Sh. K K Mitre, Vice-President, Llyod

Industries Ltd Fbd

Insulation in buildings for Refrigeration

purposes

16/3/2017

10 Prof. P M Pandey, IIT Delhi Laser 3D Printing 16/3/2017

11 Sh. Deepak Verma, Manager , Danfoss

Industries P Ltd Delhi

Future Refrigerants 16/3/2017

12 Dr. S.P. Singh,Professor IIT Delhi Dynamic Mechanical Characterization of Iron and Steel using Multi-scale Modeling Simulation particularly on Nano-Materials

17/3/2017

13 Dr. Naveen Kumar Garg, Sr Scientist CSIR-NPL

Calibration and Measurement Capabilities

17/3/2017

S.N. Activity Date Remarks

1 Dr N.K.Tiwary Ph D IIT Delhi ,

GM National Council for Cement

and Building Materials delivering

expert talk on “ Building Materials”

4.9.2018 Civil Engg Students at

YMCAUST Fbd

2 Ms Divyashree M.Tech. Thapar

Patiala and faculty in affiliated

college delivering expert talk on

“Modern Marvels in the world ”

4.9.2018 Civil Engg Students at

YMCAUST Fbd

3 Sh. Shekhar Gupta , Regional Manager

from Ador Welding Ltd delivering

expert talk on “ Various Welding

Processes ” 21.08.2018 to I Year

students at YMCAUST

FARIDABAD

21.08.2018 Civil Engg Students at

YMCAUST Fbd

4 Lecture on “ Alumunium casting”by:

Satbir Singh GM, Super Auto India

Ltd.

24.9.2018 : 11 to 12 pm

Civil Engg Students

5 Special Training Program for Civil

Engg. students arranged with NCB ,

Jan 7-11,2019 STC to Civil Engg

Students

6 Prof. M.L.AGGARWAL & I Year

Civil Engg. students, visited, Super

Auto India Ltd. Faridabad

24.9.2018 INDUSTRIAL VISIT

7 Ist Twinning Workshop” Trends &

Advances in GIS and Surveying in

Civil Engineering

” in association REC Ambedkar at

JCBUSTYMCA Faridabad

Feb. 11-12 ,2019 Civil Engg Students

8 2nd Twinning Workshop “Structural Design and Project Management in Civil Engineering” for Civil Engg Students in association REC Ambedkar at JCBUSTYMCA Faridabad

March 13-14,2019 Civil Engg Students

2019-20

Workshops/Seminars Conducted during the year 2019-20

Title of Workshop/Seminar Role, Name of the Dept. Date(s)

One week TEQIP-III

Twinning Workshop on

“Trends & Advances in GIS

and Surveying” in Civil

Engineering

Program Chair, Civil Engineering Jan 13-17,2020

Skill Training in Surveying

Camp

Program Chair, Civil Engineering January 16,2020

One day TEQIP-III

Workshop on “ BIS

Guidelines for Construction

”

Program Chair, Civil Engineering

Feb.13,2020

Six Days Online TEQIP-III

Twinning online Faculty

Development Program on

“TECHNOLOGICAL

INDUSTRIAL PRACTICES”

Convener

June 1-6, 2020

TEQIP Workshop on “CAD

: Specialized Softwares ”

Program Chair, Civil Engineering July 22-26,2019

2020-21

Workshops/Seminars Conducted during the year 2020-21

Title of Workshop/Seminar Role, Name of the Dept. 2 days State Technical

Instituitions Training

CAD/AUTOCAD Pond

Drawing, August26-27,2020

Convener

Webnair attended: Vocal for

Local,State Technical

Instituition,Nelokheri,Oct.2,20

20, Mechanical Engineering

Webinar Partcipant

Noth –Eastern Hill University

Shillong & NIT Jalandhar ’ICT

FOR PRE-SERVICE

TEACHndhar ERS,IN-

SERVICE TEACHERS

&TEACHER

EDUCATORS,Oct.21,2020

Speaker Webinar Title”Effective use of ICT for quality learning”

One Week STC TEQIP3

Online course, One Week

STC TEQIP3 Online

course, “Green

Technologies and

Environmental

Sustainability (GTES-

Convener

2020)”, Sept. 7-12,2020,

JCBUST YMCA

Faridabad

Five Days TEQIP-III

Twinning FDP ,Safety

Engineering, Oct. 12-16,2020,

Civil Dept., JCBUST YMCA

Farodabad

Program Chair,

One Week STC TEQIP3

Online course, “Control

Guidance and Estimation

of Flight Vehicles, Sept.

11-16,2020, NIT

Kurukshetra.

Participated at NIT K

Shekhar Gupta, Safety in

Welding, Expert speaker

on Oct.16,2020,11.20am,

UG/PG ME Students

ZOOM ID: 84939977072

PW: 867841

Conducted expert lecture

Certificate of Best

Upcoming Civil Engg.

Department,by Vice-

Chancellor J C BOSE

UNIVERSITY of SC.&

TECHNOLOGY

Faridabad, 2019-20,

Sept.16,2020

Award received by Prof.M.L.AGGARWAL

Building Information

Modeling

Mr Rohith Harish, Senior

Beam Project,Manager,

TECHNO STRUCT

ACADEMY, GURGAON

ACADEMY

Webnair organized by civil dept.

Best Paper Award in

International Conference

to Dr Vishal Puri,

Sh.Satyam Kumar and Dr

M.L.AGGARWAL

International Conf. on Advances in computing,Communication and Green Technology,Ansal University, July 30-31, 2020.

Value Added Course / STTP

on

Green Technologies

Organized by Civil Engg. Dept. of J C Bose University of Science

and Technology Faridabad

Total participants applied=109

Total participants completed VAD (7.9.20 -

16.9.20) = 76

Total participants completed Student STTP, R E C Ambedkar

Nagar (UP)

(7.9.20 to 12.9.20) = 33

M.L.AGGARWAL,Convener

,TEQIPIII Twinning Activity,ICT

for Students and Teachers,2.11.2020

Webinar organized by Faculty of Engg.& Technology

M.L.AGGARWAL,Convener

,TEQIPIII Twinning Activity,

Patents and Innovations, 2.11.2020

Webinar organized by civil dept.