Embed Size (px)
Citation preview
1
INSTALLATION INSTRUCTIONS
JD 1023E, 1025R & 2025R Wiring Harness Kit (TK95059)
GREYPMS 427CMYK C19 M15 Y16 K0RGB R204 G204 B204Hex #CCCCCCThrea Light Ash
BLUEPMS 647CMYK C91 M60 Y4 K0RGB R20 G103 B172Hex #1268ACThread Farm Blue
ORANGEPMS 715CMYK C0 M69 Y98 K0RGB R243 G113 B33Hex #F37121Thread Tennessee Orange
GREYPMS 428CMYK C27 M17 Y17 K0RGB R195 G197 B200Hex #c3c5c8Thread Light Gray
BLUEPMS 287CMYK C100 M87 Y20 K10RGB R32 G61 B124Hex #203d7cThread Dark Royal
BLACKPMS TBDCMYK C0 M0 Y0 K100RGB R0 G0 B0Hex #000000Thread Black
GOLDPMS 3965CMYK C1 M14 Y99 K0RGB R254 G212 B2Hex #�d402Thread NFL Yellow
DARK BLUE
CMYK C98 M74 Y24 K08RGB R14 G78 B129 HEX# 0E4E81
PANTONE 301
THREAD Empire
LIGHT BLUE
CMYK C56 M24 Y06 K00RGB R113 G164 B205 HEX# 71A4CD
PANTONE 645
THREAD Light Blue
MEDIUM BLUE
CMYK C90 M59 Y04 K00RGB R18 G104 B172 HEX# 1268AC
PANTONE 3015
THREAD Farm Blue
Kit IncludesDescription Part No. Qty.
A Relay Harness ST50580 1
B Extension Harness ST48298 1
C Switch Harness DPDT ST48299 1
D 30A Mini Blade Fuse ST50755 1
E Hardware Kit N/A 1
F Zip Ties N/A 10
This harness connects a TKV 20 to John Deere 1023E, 1025R or 2025R Compact Tractors.
AB
C
Wiring Instructions1. Park the tractor and remove the mower deck.
2. Wait for tractor to cool before working around the engine.
3. Open the hood.
4. Remove the bolt (A) that secures the side panels using a 10mm wrench, 10mm socket and ratchet. Slide the panel (B) towards the rear of the tractor and remove the panel. Repeat on the opposite side.
5. On the left side of the tractor, following the other loomed wires, insert battery ring terminals behind the exhaust bracket and into same hole as the existing wire harnesses (C).
A
B
C
Installation InstructionsNOTE: BE SURE THAT YOUR TRACTOR IS IN PARK AND THAT YOU’VE GIVEN THE ENGINE SUFFICIENT TIME TO COOL, IF PREVIOUSLY IN USE. DISCONNECT THE BATTERY.
2
6. Attach ring terminals to the battery terminals. Use a 13mm wrench to remove the battery terminal nut, slide the ring terminal over the bolt, and reinstall the nut (D). Make sure that the positive (+) battery terminal is attached to the red wire and the negative (-) battery terminal is attached to the black wire.
7. Place the relay in the corner (E) and secure the harness with zip ties at the recommended locations (F).
8. Locate and disconnect the fuel pump connector (G).
9. Plug the wire harness pigtail (H) in-line with the fuel pump connector. Secure with a zip tie to the tractor harness.
10. Moving to the other side of the tractor, continue routing the wire harness between the plastics (J) above the fuel filter.
11. Looking at the side of the tractor, continue pulling the wire and thread it down through the hole next to the existing loomed harness (K). It is recommended to loop around the main tractor harness to prevent the wire harness from contacting the linkages.
D
F
E
G
Fuel pump
H
J
K
3
12. Moving to the under side of the tractor, pull all the slack through and secure harness with zip tie to the tractor harness (L). Continue routing the wire harness parallel with the tractor harness towards the right rear of the tractor.
13. Continue at the rear right side of the vehicle, secure the harness with a zip tie to the loom (M) along the right rear main frame of the tractor.
14. Working from the rear of the tractor, continue routing the wire harness up the ROPS and secure to the existing harness (N).
L
M
N
P
15. Secure the plug to the loom (P) and bundle up any excess wire.
16. Hang the control switch assembly in the storage compartment as shown.
4
TerraKing by Superior Tech, Inc. [email protected] # TKMI-010B-10/18
WarrantyTerraKing products are guaranteed to be free from defects in material and/or workmanship and to perform as advertised when properly assembled, installed, used, and maintained in accordance with written instructions. Failure to adhere to this will void the warranty. TerraKing will not be responsible for labor, loss, or consequential damage of any kind or character caused by defective parts, or for charges incurred in the replacement or repair of defective parts. TerraKing reserves the right to request photos or return of damaged/defective parts. To submit a claim, please have your original purchase date and a copy of your receipt (if available).
Warranty PeriodThe TerraKing Wiring Harness Kit is warranted for a period of 1 (one) year after the purchase date for residential use, and 6 (six) months after the purchase date for commercial use. This product is warranted by TerraKing to the original purchaser/customer against defects in material and workmanship under normal operating conditions.
17. Secure the control switch with the supplied screws in the two locations (Q) using a Phillips head screw driver. The seat will fold forward to allow for more room for installation.
18. Connect the longer wire from the switch to the power plug and the short wire to the MCS.
Q
GREYPMS 427CMYK C19 M15 Y16 K0RGB R204 G204 B204Hex #CCCCCCThrea Light Ash
BLUEPMS 647CMYK C91 M60 Y4 K0RGB R20 G103 B172Hex #1268ACThread Farm Blue
ORANGEPMS 715CMYK C0 M69 Y98 K0RGB R243 G113 B33Hex #F37121Thread Tennessee Orange
GREYPMS 428CMYK C27 M17 Y17 K0RGB R195 G197 B200Hex #c3c5c8Thread Light Gray
BLUEPMS 287CMYK C100 M87 Y20 K10RGB R32 G61 B124Hex #203d7cThread Dark Royal
BLACKPMS TBDCMYK C0 M0 Y0 K100RGB R0 G0 B0Hex #000000Thread Black
GOLDPMS 3965CMYK C1 M14 Y99 K0RGB R254 G212 B2Hex #�d402Thread NFL Yellow
DARK BLUE
CMYK C98 M74 Y24 K08RGB R14 G78 B129 HEX# 0E4E81
PANTONE 301
THREAD Empire
LIGHT BLUE
CMYK C56 M24 Y06 K00RGB R113 G164 B205 HEX# 71A4CD
PANTONE 645
THREAD Light Blue
MEDIUM BLUE
CMYK C90 M59 Y04 K00RGB R18 G104 B172 HEX# 1268AC
PANTONE 3015
THREAD Farm Blue
