A

PROJECT REPORT

ON

“Project Name”

In partial fulfillment of

B Tech VII Semester (Computer Science & Engg.)

Session 20xx-20xx

Submitted To: Submitted by: Name of faculty Name of Student

Designation VII Semester, B Tech

Department of Computer Science & EngineeringJodhpur Institute of Engineering & Technology, Jodhpur

Certificate

This is to certify that the Project entitled “PROJECT TITLE” has been

carried out by the student/team of college Jodhpur Institute of Engineering

and Technology, Jodhpur under my guidance and supervision in partial

fulfillment of the degree of Bachelor of Technology in Computer Engineering

of Rajasthan Technical University, Kota during the academic year 20xx-20xx.

Team:

1. Name of the student 1(RTU Roll-No)2. Name of the student 2(RTU Roll-No)

Date:

Place: JIET, Jodhpur

Signature of Guide Signature of H.O.D----------------------------------- -------------------------------------- Name of Guide Name of H.O.D Designation Head Of Department, Department of CSE Department of CSE, JIET JIET

Acknowledgment

Name of StudentDate

Abstract

Table of Contents

Certificate..................................................................................................1

Acknowledgment......................................................................................2

Abstract.....................................................................................................3

Table of Contents.....................................................................................4

1. Introduction..........................................................................................5

2. Literature Survey.................................................................................6

3. Requirement Specification..................................................................7

4. Architectural Design............................................................................8

5. Test Planning........................................................................................9

6. Work Distribution..............................................................................10

7. Results..................................................................................................11

8. Conclusion & Future Work...............................................................12

Glossary...................................................................................................13

References...............................................................................................14

1. Introduction

This section should describe the basic introduction of the project scenario which is going to be implemented during this lab.

This section should also cover the following points

Technology/Programming Languages/Databases Involved:-

[Mention the technology, programming languages and Database which you are going to use during the implementation of the project.]

2. Literature Survey

This section should cover the complete literature details which has been referred during the execution of the project scenario.

The literature survey should cover the following points

1. Any website which has been referred.2. The content of the section/chapters of the book which has been referred should be

mentioned here in this section.3. The content of the section of the papers which has been referred should be mentioned

here in this section.

3. Requirement Specification

Remove the first, second, third page (title page, version tracking, table of content) of document, also remove references, acronyms, definition section of SRS, except all these content. Put Complete SRS here.

The following section of SRS document will be mentioned over here.

a. Section 2.0 “General Requirements”

4. Architectural Design

Remove the first, second, third page (title page, version tracking, table of content) of document, also remove references, acronyms, definition section of SDD, except all these content. Place those section of SDD document which are applicable to your project.

5. Test Planning

Place those section of TPD document which are applicable to your project.

6. Work Distribution

The work distribution during the implementation of the project scenario has to be mentioned in this section. If more than one student are involved in the project, than each of the student has to submit the individual implementation plan. Each plan should be in the following below format.

Name of function/ module Start Date End Date Responsible Person

1.

Write down the name of the function/module which is going to be implemented in the given timeline.

Mention the date when the implementation of function/ module is going to be started.

Mention the completion date for the implementation of function/ module.

Mention the name of the student/team member who is going to implement the function/ module.

7. Results

This section should contained the following points mentioned below.

Working Snapshots

<Snapshot Title>Write 1-2 line description of snapshot the paste snapshot here.

<Snapshot Title>Write 1-2 line description of snapshot the paste snapshot here.

<Snapshot Title>Write 1-2 line description of snapshot the paste snapshot here.

Test Status Report

S.No. Module Name

Status (Pass/Fail)

Error Status (Fixed/Open) Remarks

Write down the S.No.

Write the module name here.

Mention the status of test case after the testing

Mention the status of the bug, whether it is fixed or open.

Mention the process in brief how it has been closed. Or if remained open then why?

8. Conclusion & Future Work

This section should brief about the project work which has been done. Mention the limitation or any performance achievement occurred during the execution of the project.

Mention the work/enhancement which can be done on the project in the future.

Glossary

Write here the list of Abbreviations and Acronyms in tabular form and definitions of the terms which need to be described.

References

Mention the reference used in the project

a. Any books which have been referred.b. Any websites which have been referred.c. Any source code which have been referred.d. Any previous year project report which have been referred.

Literature References (IEEE Syntax), Examples are given as under:

a.“To refer a research paper” - Dinesh Birla, R. P. Maheshwari, and H. O. Gupta, “A New Non-linear Directional Overcurrent Relay Coordination Technique, and Banes and Boons of Near-end Faults Based Approach”, IEEE Transactions on Power Delivery, vol.-21,no.-3, pp. 1176-1182, July 2006

b.“To refer a book” - David E, Goldberg, “Genetic Algorithms in Search, Optimization, and Machine Learning”, ISBN 81-7808-130-X, Pearson Education Asia Pty Ltd., 2000. (621.381952,G47G)