JOB SCHEDULE FOR CIVIL STRUCTURE - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/1457/Tender... · JOB SCHEDULE FOR CIVIL STRUCTURE FOR THE ZONAL OFFICE BLDG.(G+6 & ONE BASSEMENT)

JOB SCHEDULE FOR CIVIL STRUCTURE FOR THE ZONAL OFFICE BLDG.(G+6 & ONE BASSEMENT)

Item Description Quantity Unit

RATE AMOUNT

CIVIL WORK

EARTHWORK

1 Earth work in excavation by manually of foundation trenches , pits or drains ,basement in grey to greyish brown silty clay or dark grey peaty muck soil. Depth of excavation for upto 1500 mm but excluding cost of shoring as necessary. The item includes necessary trimming the sides of trenches , levelling , dressing and ramming the bottom, bailing out water as required complete. 71 Cum

2 Earth work in excavation by manually of foundation trenches , pits or drains ,basement in grey to greyish brown silty clay or dark grey peaty muck soil. Depth of excavation for additional depth beyond 1500 mm and upto 3000 mm but excluding cost of shoring as necessary. The item includes necessary trimming the sides of trenches , levelling , dressing and ramming the bottom, bailing out water as required complete. 539 Cum

3 Earth work in excavation by manually of

foundation trenches , pits or drains ,basement in grey to greyish brown silty clay or dark grey peaty muck soil. Depth of excavation for additional depth beyond 3000 mm and upto 4000 mm but excluding cost of shoring as necessary. The item includes necessary trimming the sides of trenches , levelling , dressing and ramming the bottom, bailing out water as required complete. 131 Cum

4 Earth work in excavation by mechanical

means of foundation trenches , pits or drains , basement in grey to greyish brown silty clay or dark grey peaty muck soil .Depth of excavation not exceeding 1500mm. The item includes necessary trimming the sides of trenches , levelling , dressing and ramming the bottom bailing out water as required complete. 1607 Cum

5 Earth work in excavation by mechanical means of foundation trenches , pits or drains , basement in grey to greyish brown silty clay or dark grey peaty muck soil .Depth of excavation for additional depth beyond 1500 mm and upto 3000 mm excluding cost of shoring as necessary. The item includes necessary trimming the sides of trenches , levelling , dressing and ramming the bottom bailing out water as required complete.

701 Cum 6 Earth work in excavation by mechanical

means of foundation trenches , pits or drains , basement in grey to greyish brown silty clay or dark grey peaty muck soil .Depth of excavation for additional depth beyond 3000 mm and upto 4000 mm excluding cost of shoring as necessary. The item includes necessary trimming the sides of trenches , levelling , dressing and ramming the bottom bailing out water as required complete. 55 Cum

7 Filling in foundation or plinth by silver sand in

layers not exceeding 300 mm as directed and consolidating same by thorough saturation with water ramming complete. Including the cost of supply of sand. [Payment to be made on measurement of compacted quantity.]

813 Cum 8 Removal of rubbish , earth etc. from the

working site and disposal of the same beyond the compound , in conformity with the Municipal/Corporation rules for such disposal , loading into truck and cleaning the site in all respect as per direction of engineer in charge. 1958 Cum

9 Dismantling R.C.C Pile head 500 dia and

removing all rubbish from the premises 118 Cum

10 Cutting of Reinforcement steel(16 mm Dia )from pile including seegregating stirrups , straightening all the bars and stacking in proper place as directed by Engineer-in-charge. 8826 kg

11 Eucalyptus walling for shoring work including

driven into soil and extraction ( necessary framing, tie, anchorage, eucalyptus bullah piling , struting etc. at close spacing)complete for foundation excavation. Dia of Encalyptus bullah at top shall be 150 mm & bottom shall be 100 mm & length 6 m ) 1110 No

12 Shoring work with ISMB 450 spaced at 1200 mm c/c with horizontal bracing and diagonal bracing at four corners of ISMB 300 driven into the soil length 7M with in fill 12 mm M.S plate wall plate between the two ISMBs complete in all respect including extraction. 63 MT

CONCRETE WORK

13 Providing and laying 1:2:4 ( 1 cement : 2

coarse sand : 4 graded stone aggregate 40mm nominal size) cement concrete in foundations , footings bases for columns and under floors excluding the cost of centring and shuttering- all work upto plinth level 2 Cum

14 Providing and laying 1:3:6 ( 1 cement : 3

coarse sand : 6 graded stone aggregate 40mm nominal size)cement concrete in foundations , footings bases for columns and under floors excluding the cost of centring and shuttering- all work upto plinth level 135 Cum

15 Making plinth protection 50 mm thick of

cement concrete 1:3:6 (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and outward slope not flatter than 1 in 50 along transverse direction. 95 Sqm.

REINFORCED CEMENT CONCRETE

16 Controlled Cement concrete grade M25 mix

with well graded stone chips (20 mm grade) excluding shuttering and reinforcement including plasticizer with complete design of concrete as per ISI-456 and relevant special publications, submission of job mix formula alter preliminary mix design after testing of concrete cubes as per direction of Engineer-in-charge. Consumption of cement will not be less than 6 bags/300 kg of cement per cube meter of controlled concrete but actual consumption will be determined on the basis of preliminary test & job-mix formula. In substructure with Pakur / Chandil Variety 136 Cum

17 Controlled Cement concrete grade M25 mix

with well graded stone chips (20 mm grade) excluding shuttering and reinforcement including plasticizer with complete design of concrete as per ISI-456 and relevant special publications, submission of job mix formula alter preliminary mix design after testing of concrete cubes as per direction of Engineer-in-charge. Consumption of cement will not be less than 6 bags/300 kg of cement per cube meter of controlled concrete but actual consumption will be determined on the basis of preliminary test & job-mix formula. In superstructure with Pakur / Chandil Variety 349 Cum

18 Ready mix concrete grade M25 mix with well

graded stone chips (20 mm grade) excluding shuttering and reinforcement with complete design of concrete as per ISI-456 and relevant special publications, submission of job mix formula alter preliminary mix design after testing of concrete cubes as per direction of Engineer-in-charge. Consumption of cement will not be less than 6 bags/300 kg of cement per cube meter of controlled concrete but actual consumption will be determined on the basis of preliminary test & job-mix formula. Manually in substructure 94 Cum


graded stone chips (20 mm grade) excluding shuttering and reinforcement with complete design of concrete as per ISI-456 and relevant special publications, submission of job mix formula alter preliminary mix design after testing of concrete cubes as per direction of Engineer-in-charge. Consumption of cement will not be less than 6 bags/300 kg of cement per cube meter of controlled concrete but actual consumption will be determined on the basis of preliminary test & job-mix formula. Manually in superstructure 313 Cum

20 Ready mix concrete grade M25 mix with well graded stone chips (20 mm grade) excluding shuttering and reinforcement with complete design of concrete as per ISI-456 and relevant special publications, submission of job mix formula alter preliminary mix design after testing of concrete cubes as per direction of Engineer-in-charge. Consumption of cement will not be less than 6 bags/300 kg of cement per cube meter of controlled concrete but actual consumption will be determined on the basis of preliminary test & job-mix formula. By pumping in substructure

719 Cum


graded stone chips (20 mm grade) excluding shuttering and reinforcement with complete design of concrete as per ISI-456 and relevant special publications, submission of job mix formula alter preliminary mix design after testing of concrete cubes as per direction of Engineer-in-charge. Consumption of cement will not be less than 6 bags/300 kg of cement per cube meter of controlled concrete but actual consumption will be determined on the basis of preliminary test & job-mix formula. By pumping in superstructure

962 Cum

22 Centring and shuttering with 12 mm thick

water proof ply board including strutting, propping , bracing of props etc. For :Foundations , Pile cap , footings bases of columns etc. and mass concrete and removal of form for and hacking of deshuttered concrete members. 10 Sqm.


water proof ply board including strutting, propping , bracing of props etc. For :Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc and removal of form for and hacking of deshuttered concrete members. 4083 Sqm.


water proof ply board including strutting, propping , bracing of props etc. For :Suspended floors, slabs, roofs, landings, balconies and access platform and removal of form for and hacking of deshuttered concrete members. 4635 Sqm.

25 Centring and shuttering with 12 mm thick water proof ply board including strutting, propping , bracing of props etc. For :Lintels, beams, plinth beams, girders, bressummers and cantilevers and removal of form for and hacking of deshuttered concrete members.

3338 Sqm.

26 Centring and shuttering with 12 mm thick water proof ply board including strutting, propping , bracing of props etc. For :Columns, pillars, piers , abutments , posts and struts and removal of form for and hacking of deshuttered concrete members. 1297 Sqm.


water proof ply board including strutting, propping , bracing of props etc. For :Stairs (excluding landings) except spiral staircases and removal of form for and hacking of deshuttered concrete members. 932 Sqm.


water proof ply board including strutting, propping , bracing of props etc. For :Weather shade , Chajjas , Corbels etc. including edges and removal of form for and hacking of deshuttered concrete members. 42 Sqm.

29 Centring and shuttering with suitable thick water proof ply board for Walls (any thickness) including attached pilasters, including strutting, propping , bracing of props etc. and removal of form and hacking after deshuttered for Circular shuttering to ensure smooth finished surface 56 Sqm.

30 Centring and shuttering with suitable thick

water proof ply board for Columns, pillars, piers and removal of form and hacking after deshuttered for Circular shuttering to ensure smooth finished surface. 108 Sqm.

31 Reinforcement with Thermo mechanically

treated bars for R.C.C work including straightening , cutting, bending, placing in position and binding all complete. 385627 Kg.

BRICK WORK

32 Brick work with nominal thickness of 250 mm or more bricks of crushing strength not less than 75kg/sqcm in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse 31 Cum.

sand)

33 Brick work with bricks nominal thickness of

250 mm or more of crushing strength not less than 75kg/sqcm superstructure above plinth level up to floor V level in all shapes and sizes including single scaffolding in: Cement mortar 1:4 (1 cement : 4 coarse sand) 341 Cum.

34 Extra for brick work in superstructure nominal

thickness of 250 mm or more of crushing strength not less than 75kg/sqcm above floor V level for every four floors or part thereof by mechanical means by lifting material using building hoist. 141 Cum.

35 Single brick flat soling (Nominal Thickness 75

mm ) with picked jhama bricks including preparation of bed as necessary with brick joints properly filled and packed with powdered earth and including necessary cushion of similar materials below the soling complete as per direction. 681 Sqm

36 Half brick masonry with bricks of crushing

strength not less than 75kg/sqcm in substructure (foundation & Plinth ) as shuttering work for Pile cap & Grade beam with Cement mortar 1:4 (1 cement : 4 coarse sand) 664 Sqm

37 Half brick masonry with bricks of crushing

strength not less than 75kg/sqcm in superstructure above plinth level upto floor V level including single scaffolding with Cement mortar 1:4 (1 cement : 4 coarse sand) 1953 Sqm

38 Extra for half brick masonry with bricks of

crushing strength not less than 75kg/sqcm in superstructure above floor V level for every four floors or part thereof by mechanical means by lifting material using building hoist. . 650 Sqm

39 Extra for providing and placing in position 2

nos. 8mm. Dia. T.M.T bars at every third course of half brick masonry

1953 Sqm

STEEL WORK

40 Supplying and fixing rolling shutters of

approved make,made of required size M.S laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs grade No 2 and M.S top cover of required thickness for rolling shutters. The rate shall be included steel primer as one coat of shop painting. 26 Sqm.

41 Providing and fixing ball bearing for rolling

shutters. 6 Each

42 Providing and fixing Circular/hexagonal M.S sheet ceiling fan box with clamp of internal dia 140 mm, 73 mm height , 3 mm thick rim , top and bottom lid of 1.5mm thick M.S sheet.Lids shall be screwed into M.S box by means of 3 mm dia. round headed screws, clamps shall be made of 12 mm dia M.S bar bent to shape as per standard drawing with overall length as 80 cm..

2 each

43 Providing and fixing 8 mm thick insert plate of different sizes of M.S plate including lug etc. as per direction of the Engineer-in-charge. 57 Kg

FLOORING

44 20 m.m.thick,(Minimum) Kota stone slab cut in desired sizes set in cement mortar (1:4) in matching line joint over 20 m.m. thick base (minimum) including levelling course with same mortar as required in floor (risers , treads , landing of staircase )considering slab size not more than 600 x 600 mm in landing areas including pointing in cement mortar (1:2) (1 cement : 2 stone dust) with admixture of pigment matching the stone shade including grinding and polishing, as per direction of Engineer-in-charge to match with the existing work. 373 Sqm

45 Supplying, fitting and fixing 20

m.m.thick(Minimum) Kota stone slab cut in desired sizes in wall, dado in cement mortar (1:3) matching line joint over 12 m.m. base (minimum) including making suitable arrangement to hold the stone properly including pointing in cement mortar (1:2) (1 cement : 2 stone dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-charge including cost of Materials, Labour, curing complete. 123 Sqm

46 Providing and fixing 1 st quality Ceramic

glazed tiles 300x300 mm of approved make conforming to IS :15622( of 7 mm thickness) in all colours , shades except burgundy , bottle green , black of any size as approved by Engineer -in -charge in Dados over 12 mm thick bed of Cement Mortar 1:4 [ 1 Cement : 4 Coarse Sand ] and jointing with grey cement slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 580 Sqm

47 Providing and fixing 1 st quality Ceramic

border glazed tiles 300x100 mm of approved make conforming to IS :15622( of 7 mm thickness ) in all colours , shades except burgundy , bottle green , black of any size as approved by Engineer -in -charge in Dados over 12 mm thick bed of Cement Mortar 1:4 [ 1 Cement : 4 Coarse Sand ] and jointing with grey cement slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 33 Sqm

48 Providing and laying Ceramic glazed floor tiles 300 x 300 mm [of 7 mm thickness] of approved make of 1 st quality conforming to IS :15622 in all colours , shades except white , ivory , grey , fume red brown , laid on 20 mm thick Cement Mortar 1:4 [ 1 cement :4 coarse sand] including pointing the joints with white cement and matching pigment etc. complete. 166 Sqm

49 Providing and laying 40 mm th IPS flooring

(1:2:4)(1 cement : 2 coarse sand : 4 stone aggregate of 20 mm and down nominal size )with floor hardener 855 Sqm

50 Providing and laying 25 mm th IPS flooring

(1:2:4)(1 cement : 2 coarse sand : 4 stone aggregate of 12.5 mm and down nominal size ) finishing with a floating coat of cement including cement slurry etc. complete. 63 Sqm

51 Providing and fixing 25 x 4 mm thk glass

strips in joints of Cement concrete floors 2556 Rm

52 Extra for prefinished nosing to treads of steps of kota stone. 584 Rm

ROOFING

53 Grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size ) 81 Cum

FINISHING

54 12mm internal cement plaster (in RCC work)

including double scaffolding of mix 1:4(1 cement :4 Fine sand ) 2813 Sqm

55 15mm internal cement plaster (Brick

work/RCC Work)on the rough side of single or half brick wall including double scaffolding of mix 1:4(1 cement :4 Fine sand ) 7908 Sqm

56 18mm cement plaster (External)in two coats under layer 12 mm thick cement plaster 1:4 (1 cement : 4 Coarse sand) finished with a top layer 6 mm thick cement plaster 1:4(1 cement : 4 fine sand ) including mixed with admixture of waterproofing compound in both layers as per manufacturer's specification and complete double scaffolding 3864 Sqm

57 6mm plaster to ceiling including double scaffolding of mix 1:4 (1 cement : 4 fine sand) 2051 Sqm.

58 Neat cement punning 548 Sqm.

59 Supply and fixing "SHON" make mosaic tiles

( ceramic unglazed )in size of 25x25x4 mm thick (+/-)1% in white colour matt finish fixed over smooth cement plaster surface with white tile adhesive and joint filling with white cement and acid cleaning the surface including double scaffolding etc. complete in all respects as per the instruction of Engineer-in-charge.

990 Sqm

60 Providing and fixing of approved brand's &

manufacturer's open groove , three barrier semi-unitized structural glazing system ensuring max U-value at all levels through designing and selection of Aluminium alloy and tempered vertical Mullion and horizontal Transom extruded profiles anodized to 15 microns minimum according to approved color along with necessary corrosion resistance accessories/hardwares/fittings and specially designed/extruded imported non aging siliconised gaskets as per approved specification. For their fixing to the backup support structures depending on the structural conditions , functional and statistical load requirements with reference to IS:875-1987 (part III) with adequate anchoring point within the floors and system should support and transfer their own self weight OR dead loads to the main building structure. The system shall provide proper rebate areas for air pressure compensation and water drainage and smoke seals.

24 mm thick coloured reflective toughened insulated Glass shall be fixed glued with structural sub frame. Special supporting elements shall be provided for taking care of the respective infill load and reliving in case of the glass bonding failure. Glass thickness shall be adequate to withstand the aggressive wind load relevant for the location as per IS:875-1987 (part III). All components should be sealed for water proofing with silicon weather sealant from DOW CORNING-DC 789 shall take care of joint movements. The backup support structure shall be loaded on to the civil structure with the help of the hot dipped galvanised MS brackets and SS 304 grade bolts/nuts & Hilti/Fischer or equivalent anchor fasteners. All components should be sealed for water proofing with silicon weather sealant Continuous structural glazing

1051 Sqm

. 61 Same as above but Extra for openable

windows 15 Sqm

62 Providing and fixing of approved brand's & manufacturer's open groove , three barrier semi-unitized structural glazing system ensuring max U-value at all levels through designing and selection of Aluminium alloy and tempered vertical Mullion and horizontal Transom extruded profiles anodized to 15 microns minimum according to approved color along with necessary corrosion resistance accessories/hardwares/fittings and specially designed/extruded imported non aging siliconised gaskets as per approved specification. For their fixing to the backup support structures depending on the structural conditions , functional and statistical load requirements with reference to IS:875-1987 (part III) with adequate anchoring point within the floors and system should support and transfer their own self weight OR dead loads to the main building structure. The system shall provide proper rebate areas for air pressure compensation and water drainage and smoke seals.

6 mm thick tinted, toughened Glass and colours as specified and finalised between HPCL/GEL for spandrel area shall be fixed glued with structural sub frame. Special supporting elements shall be provided for taking care of the respective infill load and reliving in case of the glass bonding failure. Glass thickness shall be adequate to withstand the aggressive wind load relevant for the location as per IS:875-1987 (part III). All components should be sealed for water proofing with silicon weather sealant from DOW CORNING-DC 789 shall take care of joint movements. The backup support structure shall be loaded on to the civil structure with the help of the hot dipped galvanised MS brackets and SS 304 grade bolts/nuts & Hilti/Fischer or equivalent anchor fasteners.

269 Sqm

63 Providing and fixing of approved brand

openable windows within the curtain wall system at all levels through designing and selection of Aluminium alloy and tempered frame and shutter extruded profiles with reference to the desired strength anodized according to approved colour along with the corrosion resistance accessories and hardwares /fittings like handles and specially designed /extruded imported non aging siliconised micro wave treated gaskets as per the specification for their fixing to the backup support structures depending on the structural conditions , functional and statistical load requirements. The system shall provide proper rebate areas for air pressure compensation and water drainage. Glass of 6 mm thickness shall be fixed with infill frame with specified extruded glazing clip on the specially treated glazing component attached to the infill frame.Special supporting elements shall be provided for taking care of the respective infill / shutter dead load. All components should be sealed for water proofing with silicon weather sealant. 264 Sqm

64 Supplying and fixing Coloured anodised Al

fixed louver ventilators including all necessary fittings & fixtures complete in all respect.

8 Sqm

65 Supplying and fixing 32 mm thk. Wooden flush door with 1 mm th glossy/matt lamination of approved make on both sides & providing 3 nos of satin stainless steel finish Dorma make butt hinges , 1 no Mortice sash lock , 1 no floor stop ,1 no flush bolt, 1 pair Ogro make lever handle , 1 no Satin nickle plated finish Dorma make 5 pin Euro profile cylinder , 1 no Dorma make silver finish door closure complete in all respect. 97 Sqm

66 Extra for providing lipping with 2 nd class

teak wood battens 25 mm minimum depth on all edges of shutters [ over all area of door shutter to be measured] on flush door 97 Sqm

67 Wood work in door frame with Siliguri sal

fitted and fixed complete including a protective coat of solignum painting at the contact surface of the frame. 3 Cum

68 Supply & erection of 19 mm thick granite

cladding of approved shade of size not exceeding 900 mm square on the external surface as per drawing on 150 mm long stainless steel clamps set in the masonry work with stainless steel dowels of size 50 mm x 8 mm thick aligned properly @ 600 c/c maximum on both ways jutting out of the 20 mm thick Cement sand external plaster and clamped with the granite slabs properly as per direction of Engineer-in-charge.(Basic Rate of Granite=Rs 200/Sqft)

188 Sqm

ACP cladding system 69 Supplying and fixing PVDF-Exterior grade 4

mm thick aluminium composite panel of approved make as per approved manufacturer's specification fixed on aluminium frame work with necessary bolts , nuts , washers & foil coating of 0.5 mm thick fixed to the wall as certified by Engineer-in-charge complete in all respect.

214 Sqm

Aluminium Louver system 70 Providing and fixing in position Luxalon 84 R

plain panel aluminium sun-louver system as specified in the Technical specification of Hunter Douglus India Pvt. Limited. The panels shall be coil coated with colour as specified by architect fixed in a module of 69 mm c/c at a distance of 1 m with necessary aluminum accessories , nut, bolts , washers complete as per design.

1034 Sqm

Spigot fixed midrail system (Staircase

Balustrade ) 71 Supply and installation of satin finish

stainless steelSS handrail and balustrade system of approved make having 38 mm dia tube handrail ( 1.5 mm gauge ) weight 2.82 kg of 2000 mm dia 38 mm tube handrail , connected with unified stem keys in bead blasted finish to 12 x 54 mm stain finish flat vertical member weight 7 kg per piece , erected with chemical grout to be fixed on the top of staircase ( spigot fixed ) at max c/c distance of 1800 mm with infill of two horizontal midrail of 22 mm dia & weight 1.64 kg of 2000 mm midrail complete with all necessary bends and terminations and set of accessories weight of 5 kg Ht at the staircase would be 900 mm and the ht. at the landing area would be 1100 mm.

115 rmt

72 Upright

118 Nos

73 Supply and installation of satin finish stainless steel AISI 304 ss wall mounted system having 38 mm dia tube rail with 1.5 mm gauge of 2000 mm dia 38 mm tube handrail connected with unified stem key in bead blast finish complete with all necessary bends and termination.

53 rmt

Fire Closing Door 74 Supply & installation of fire closing door of

"SHAKTI MET-DOR" of Two hour fire rating as per manufacturer's specification.

51 Sqm

75 Applying one coat of cement primer of

approved brand and manufacture on wall surface including double scaffolding: 3767 Sqm

76 Finishing walls with water proofing cement

based acrylic latex paint on external unexposed surfaces of required shade:New work ( Two or more coats applied @ 3.84 kg/10 sqm ) 3767 Sqm.

77 Providing & fixing M/F suspended ceiling includes G.I perimeter channels of size 0.55 mm thick having one flange of 20 mm and another flange of 30 mm and a web of 27 mm along with perimeter of ceiling. It is screw fixed to brick wall/partition with the help of nylon sleeves and screws , at 610 mm centres. Then G.I intermediate channels of size 45 mm (0.9 mm thick with two flanges of 15 mm each made of G.I steel Gypsteel embossed with hologram) are suspended from the soffit at 1220 mm centres with ceiling angle of width 25 x 10 x 0.55 mm thick made of G.I steel gypsteel embossed with hologram. This is then fixed to the soffit with G.I cleat and steel expansion fasteners. Ceiling section of 0.55 mm thickness having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm made of G.I steel Gypsteel embossed with hologram are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457 mm centres. 12.5 mm tapered edge Gypboard [Conforming to IS: 2095-1996: Part- I ]is then screw fixed to ceiling section with

25 mm drywall screws at 230 mm centres. Screws fixing is done mechanically either with screwdriver or drilling machine with suitable attachment. Finally , the boards are to be joined and finished so as to have a flush look , which includes filling and finishing the tapered and square edges of the boards with jointing compound , joint paper tape and two coats of Drywall top coat suitable for Gypboard [ as per recommended practices of BPB India Gypsum] and creating necessary recesses for recessed light fittings as and where applicable.

166 Sqm

78 M.S clamp for fixing door frame made of flat

bent bar , end bifurcated , fixed in cement concrete with stone chips (1:2:4) fitted and fixed complete inclusive of cutting of necessary pockets in masonry & concrete as per direction.(Cost of cement concrete will be paid separately)

40 mm x6 mm x 300 mm length 330 Each

79 Providing and fixing40 mm dia & 50 mm long rubber buffer block fixing in screw with back side of doors as per direction of the engineer-in-charge. 54 Each

80 Providing and fixing aluminium hanging floor door stopper ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour and shade with necessary screws etc complete . Single rubber stopper . 24 Each

81 Providing & fixing battened of 2 nd class teak

wood of sizes 20 mm x 6 mm in all sides of vision panel sizes 300 mm x 150 mm and 6 mm thick ordinary glass panes including polising of battens as per direction of the engineer-in-charge. 12 Each

MISCELLANEOUS ITEMS

82 Preparing the roof surface free from dust , oil , grease , any loose particles with compressed air & repairing surface irregularities , damaged concrete in base slab , if any with a styrene butadiene polymer including a coat of bonding agent of the same with cement slurry. Prepared substrate shall be treated with a two component acrylic polymer modified , cementitious , ready to use , flexible waterproofing slurry at right angles to each other and taking the coatings over the vertical parapet upto at least 300 mm on the exterior surface of the parapet. Mixing ratio is 1:4 by weight and the density 2.1 kg/l approx. After that a cementitious membrane is dried , an acrylic bond coat of cement slurry shall be applied. Specific gravity 1.03 approx. When the bond coat is tacky, the area shall be laid with a minimum 50mm avg. thick concrete screed admixed with the waterproofing compound, ensuring that the screed gently slopes towards the drain pipes. The concrete screed should be cast in panels of 2mx2m maintaining 10mmx10mm groove

using solvent free polyurethane pavement sealant. The density is 1.3kg/l. All corners and joints such as those between the parapet wall and the roof slab, chimney and roof slab, etc shall be chamfered with 150mm X 150 mm fillet of mortar (Cement: sand – 1:4) admixed with waterproofing compound. Before chamfering a prime coat shall be given with the slurry of a water proofing compound. Specific gravity 1.03 approx.& complete in all respect.(Screed concreting will be paid separately.) 802 Sqm

83 Preparing the basement floor surface from dust and loose adhereing particles apply 12 mm th plaster(1:4) on P.C.C Supply and application of an 4 mm thick APP modified bituminous membrane, plain finished on the cured surface.(including primer) Providing a 12mm thick plaster on the waterproof membrane before fixing of the reinforcements. The screed should be prepared by mixing an integral waterproofing compound, @ 100gms per bag of cement Supply and application of an expanding grout admixture for pressure grouting using min. 15mm dia, 100mm long GI nozzles 1.5 m C/C in the concrete with the help of 200mm long dummy rod. Dummy rod should be removed after the initial set of concrete. Extra nozzles are to be provided along the construction joint & complete in all respect.

736 Sqm

84 Preparing the basement wall surface from dust and loose adhereing particles Supply and application of an 4 mm thick APP modified bituminous membrane, plain finished on the cured surface.Providing a polystyrene board, at least 25mm thick on the surface with a bituminous adhesive.Providing a polystyrene board, at least 25mm thick on the surface with a bituminous adhesive. & complete in all respect.

285 Sqm

85 Supplying & applying two coats of cementitious , flexible waterproofing coat on the properly clean , dust free sunken floor & vertical surface , and 15 mm th plaster (1:4)mixed with an integral waterproofing compound will be applied over the waterproof coating. 1:3 cement sand mortar mixed with the polymer modified high quality emulsion to be used as a coving at the corners of floor and the vertical surface & a moisture insensitive epoxy putty in a continuous , 10 mm thick gasket around the pipes to a width of approximately 15 mm & complete in all respect. 242 Sqm

86 Supply & installation of 50 mm dia 18 SWG 2

Way MS circular Junction Box(IS:226) 111 No

87 Providing & Inserting 19 mm Rigid PVC Pipe in roof slab for cable 500 M

88 Providing fixing C.I manhole cover with frame

(heavy duty) 560 mm diameter, total weight of cover with frame to be not less than 125 kg (weight of cover 108 kg ) 4 Nos

89 Providing and fixing (50 mm dia ) C.I Vent

Pipe with one bent & one vent Cowl complete in all respect. 1 No

90 Providing and fixing 16 mm dia Tor steel U

shaped 150mm wide Steps fixed in R.C.C. or masonry wall with cement concrete (1:2:4) 13 Kg

91 Supplying & applying two coats of

cementitious , flexible waterproofing coat on the properly clean , dust free sunken floor & vertical surface , and 15 mm th plaster (1:4)mixed with an integral waterproofing compound will be applied over the waterproof coating. 1:3 cement sand mortar mixed with the polymer modified high quality emulsion to be used as a coving at the corners of floor and the vertical surface & a moisture insensitive epoxy putty in a continuous , 10 mm thick gasket around the pipes to a width of approximately 15 mm & complete in all respect. 101 Sqm

92 Preparing the U.G Tank floor surface from

dust and loose adhereing particles apply 12 mm th plaster(1:4) on P.C.C Supply and application of an acrylic coating on the prepared substrate after making the surface in SSD condition. Mix ratio is 1:4 by weight and the density 2.1 kg/l approx. Providing a 12mm thick plaster on the waterproof coating before fixing of the reinforcements. The screed should be prepared by mixing an integral waterproofing compound, @ 100gms per bag of cement Supply and application of an expanding grout admixture for pressure grouting using min. 15mm dia, 100mm long GI nozzles 1.5 m C/C in the concrete with the help of 200mm long dummy rod. Dummy rod should be removed after the initial set of concrete. Extra nozzles are to be provided along the construction joint. & complete in all respect. 49 Sqm

93 Preparing the U.G Tank wall surface from dust and loose adhereing particles Supply and application of an acrylic coating on the prepared substrate. Providing a 12mm thick protective plaster on the waterproof coating. The screed should be prepared by mixing an integral waterproofing compound, @ 100gms per bag of cement Supply and application of an expanding grout admixture for pressure grouting using G.I nozzles and by fixing the nozzles 1.5m c/c. Dosage. 1% by weight of cement After necessary surface preparation, apply two coats of water based, food grade epoxy coating on the RCC surface from inside. This is two component system, comp.A:comp.B:: 1:1 by weight and density is 1.2 kg/l. & complete in all respect. 329 Sqm

94 Providing and fixing 200 mm dia , 600 mm

length puddle piece with a plate and length of pipe IS 1239(Part1)(varies as per requirement ) during casting of concrete and a shop coat of zinc primer. 2 No.





97 Providing and fixing 100 mm dia, 300 mm



length puddle piece with a plate and length of pipe IS 1239(Part1)(varies as per requirement ) during casting of concrete and a shop coat of zinc prime 1 No.


length puddle piece with a plate and length of pipe IS 1239(Part1)(varies as per requirement ) during casting of concrete and a shop coat of zinc prime 2 No.

DRAINAGE-INTERNAL, (INCLUDING RAIN WATER DOWNTAKE PIPES UPTO THE CATCH-PITS / SURFACE DRAIN, & ALSO INCLUDING THROUGH SUNKEN PORTION OF "SOIL" QUALITY C.I. SEWER

& WASTE PIPES / FITTINGS; UP TO THE STACKS & INCLUSIVE OF ALL STACKS, COWL , FITTINGS ETC, UPTO THE FIRST INSPECTION PITS, OR UPTO STORM WATER SURFACE DRAIN)

SL.NO. ITEM DESCRIPTION QTY UNIT RATE AMOUNT

SUPPLY, INSTALLATION, TESTING & COMMISSIONING

SANITARY INSTALLATIONS & FITTINGS

100 Providing and fixing white vitreous china

"Wall- hung" type water closet (European type W.C. pan) with seat and lid, conforming to IS : 2556; and including C.I. bracket Chair remaining concealed in Wall, also with Jaquar, "Allied", cat. no.-1015 CP Flush valve with 32mm Control cock & Elbow Set complete with adjustable sleeve and wall Flange, with all fittings and fixtures, i,e., 100mm dia CI / PVC WC outlet of Plain Bend or straight 'Short piece' of required length with "Push fit" rubber seal (IS-5382), complete including cutting and making good the wals and floors wherever required.(Wall mounted with "P" type) -colour-"Star White". W.C. pan with Standard Seat Cover and lid.(Make :- "Hindware"- Constellation, cat no.-20040 / "Parryware", cat no.-0220)

26 each

101 Providing and fixing white vitreous china "Floor mounted" Pedestal type water closet (European type W.C. pan) with seat and lid, conforming to IS : 2556; including with Jaquar, "Allied", cat. no.-1015 CP Flush valve with 32mm control cock & Elbow set complete with adjustable Sleeve and Wall Flange; with all fittings and fixtures complete including cutting and making good the wals and floors wherever required. (for Driver's Toilet at the Gr. floor) (colour- Star White) - "S" Trap type W.C. Pan with ISI marked Black solid plastic seat and lid. (Make :- "Hindware"- Slick, cat no.-20011, without Cistern / "Parryware", cat. No.-0287)

1 each

102 Providing and fixing white vitreous china Flat back "Large" lipped front Urinal Basins of 590x390x375mm sizes respectively, with standard flush pipe and C.P. brass spreaders (of 'Crabtree' make, cat. no.-11021 or "Paryyware, cat.no.-C 8095) in each Urinal Basins, with brass unions, fixing screws on wall etc, and C.I. / G.I. clamps or brackets, complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

(Urinals with Integral Flushing Rim). (Make :- "Hindware"-Flat back 'Large', cat.

No.-60002 / "Parryware", cat. No.- 0508)

(As per IS-2556) Range of three Urinal basins of Hindware/

Parryware 5 each "Flat Back Large"-(590 x 390 x 375mm)

[Jaquar make SENSOR for flushing are

taken in other item].

103 Range of two Urinal basins of Hindware/ Parryware 1 each

"Flat Back Large"-(590 x 390 x 375mm) [Jaquar make SENSOR for flushing are

taken in other item].

104 Range of four Urinal basins of Hindware/ Parryware 2 each

"Flat Back Large"-(590 x 390 x 375mm)

[Jaquar make SENSOR for flushing are taken in other item].

105 Providing and fixing Urinal "Sensors" with

Installation box with Control cock for Sensor Flushing valve (Battery operated).

(Make :- Jaquar -"SENSOR", cat no.- 51077 & 51079 / "Crabtree" )

25 each

106 Providing and fixing "Oval" pattern, "Under Counter" type Wash Basin of size 560 x 410mm, with C.I./ M.S.brackets, 32mm. C.P brass Half thread Waste Coupling (of 'Jaquar' make, cat. no.-709, Allied) of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

"Star White"- Vitreous China-ware, as per IS-2556

(Make :- "Hindware", "OVAL", code- 10017, size- 560 x 410mm / or "Parryware", cat. No.- 0418, size- 550 x 450mm)

"Oval" Wash basin size 560 x 410mm.of "Hindware" / or 550 x 450mm of "Parryware' 37 each

107 Providing and fixing Mirror thickness of

required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Rectangular shape 453x357 mm 37 each (Make :- "Modi Guard" / "Indo-Ashai")

108 Supplying and fixing of 32mm C.P. brass Bottle Trap with waste Pipe and C.P. wall flange of standard pattern, including cutting and making good the walls wherever required.

(Bottle trap with 32 mm dia, 190 mm long wall connection pipe - Make - 'JAQUAR', - Allied - Code - 773 56 each

109 Supplying and fixing of 32mm C.P. brass Bottle Trap with waste Pipe and C.P. wall flange of standard pattern, including cutting and making good the walls wherever required.

(Bottle trap with 32 mm dia, 190 mm long wall connection pipe - Make - 'ESSCO', - Allied - Code - 546

(In Driver's Toil. Wash Basin only) 6 each

110 Providing and fixing of CP Robe Hooks with double forks, supported on anodised chromium plated Base, fixed with 40mm long screws, rawl plugs etc., all complete.

(Make :- "Jaquar"- Stealth, cat. no.- 21761)

With Chromium plated flange 30 each

111 Providing and fixing of CP Robe Hooks with single / double forks, supported on anodised chromium plated Base, fixed with 40mm long screws, rawl plugs etc., all complete.

(Make :-"Jaquar"-continental, cat. no.- 1191) 1 each

(In Driver's Toil. only)

112 Supplying, fitting and fixing C.P. liquid Soap Holder, including C.P. screws complete as directed and specified (Make - Any Approved make )

(In all Toils. above each Wash Basins only)

With Chromium plated flange 37 each

113 S.S. / CP Circular Grating (with or without hole); with cockroach arrestor device.

(Make - "Chilly") (In all Floor Trap / "P" trap mouths)

150 mm 28 each

114 S.S. / CP Circular Grating (with or without hole); with cockroach arrestor device.

(Make - "Chilly") (In all Floor Trap / "P" trap mouths)

ii) 125 mm 26 each

115 Providing and fixing CP Toilet paper Holder with all fixing accessories.

C.P. Brass (Make :- "Jaquar"- Stealth, cat. no.- 21751) 26 each

116 Providing and fixing CP Toilet paper Holder with all fixing accessories.

C.P. Brass (Make :- "Jaquar"- Continental, cat. no.- 1151)

(In Driver's Toil. only) 1 each

117 Providing and fixing of CP Towel Rail with 600mm long x12mm dia CP Rod supported on anodised chromium plated frame, fixed with C.P brass backets, complete with 40mm long screws, rawl plugs etc., all complete. (for Manager's Toil & common Toil.- Gents) (Make :- "Jaquar" , Stealth, cat. No.-21711) 24 each

118 Providing and fixing of CP Towel Rail with 600mm long x12mm dia CP Rod supported on anodised chromium plated frame, fixed with C.P brass backets, complete with 40mm long screws, rawl plugs etc., all complete. (for Driver's Toil.) (Make :- "Jaquar", Continental, cat/ no. - 1111) 1 each

119 Supplying, fitting and fixing CP Soap Dish, including

C.P. screws complete as directed and specified

(Make - "Jaquar", -"Stealth", cat. No.- 21731)

With necessary fixings, rawl plugs etc. 26 each

120 Supplying, fitting and fixing of Salem Stainless Steel Kitchen Sink - (AISI-304, conforming to IS-13983), Single Bowl, built with superior steel, with Bowl size not less than- 560 x 410mm and with Bowl depth of 205mm to 215mm; and total overall size - 1145 x 510mm, with a provission of a Drain-board, also including with 40mm Salem Stainless Steel Unique Waste Coupler and Copler knob etc., including C.I. / MS fixing Brackets, C.P. screws/washers etc., and painting of Brackets, cutting and making good the walls wherever required etc., all complete.

(Make - 'Hindware' - "Ester Sumo", / Parryware / Hefele / Nirali ) With necessary fixings, rawl plugs etc. (In Kitchen & Dish Wash) 3 each

121 Supplying, fitting and fixing of Salem Stainless Steel

Kitchen Chimney, with 3-speed, single Motor design, Stainless Steel body, with Psh buttons, 900 - to- 1000 M3 / hr. - suction power, with Multi-layer anodised aluminium Mesh Filter, including with required length G.I. Ducting work of required size etc., including C.I. / MS fixing Brackets for Ducting, C.P. screws/washers etc., and painting of Brackets, cutting and making good the walls wherever required etc., all complete.

(Make - 'Hindware'- "MAGNA", cat. No.- C 100009 / 'Kutchina' - model- "Eleganza" ) 2

each

122 Providing and fixing C.P. Brass 2-way Bib cock with

wall flange of approved quality conforming to IS : 8931

(Make :- "Jaquar", - "Stealth", cat. No.- 21041)

15 mm nominal bore 26 each

123 Providing and fixing C.P. Brass Bib cock of approved quality conforming to IS : 8931

(Make :- Essco, -"Delux", cat no.- ES 511) 15 mm nominal bore 1 each (In Driver's Toil. Only)

124 Providing and fixing C.P. Brass Stop cock

(concealed) of standard design of 'Heavy' grade with CP Sheet Flange and of approved make conforming to IS : 8931

(For Urinals only) (Make :- Essco, cat no.-ES 514 F-(Delux)) 20 mm nominal bore 8 each

125 Providing and fixing C.P. brass Angular Stop Cock for Wash Basins, Sinks of approved quality conforming to IS : 8931

(Make :- Jaquar- "Stealth", cat. no.- 21053)


126 Providing and fixing C.P. brass Angular Stop Cock for Wash Basin, of approved quality conforming to IS : 8931

(In Driver's Toil. + for Kitchen Sink) 15 mm nominal bore (Make :- Essco, cat no.-ES 526-(Delux)) 4.0 each

127 Providing and fixing C.P. brass Pillar Cocks for Wash Basins of approved quality conforming to IS : 8931

(In Driver's Toil.) 15 mm nominal bore 1 each (Make :- Essco, cat no.-ES 508-(Delux))

128 Providing and fixing C.P. brass "Sensor Faucet" (Pillar Cock), for Wash Basins complete with Control Box (Battery operated).

(Make :- Jaquar -"SENSOR", cat no.-

51011)


129 Providing and fixing C.P. brass Sink Cock - "Jaquar", 'Clarion', cat. no.- 23321 B, Sink Mixer with extended Spout (Table mounted model) with 450mm long Braided Hoses, for Kitchens of approved quality conforming to IS : 8931

(Make:-Jaquar, "Clarion", cat. no.- 23321 B)

15 mm nominal bore 3 each (In Kitchen & Dish wash only)

130 Providing and fixing C.P. brass Stop Cocks with female threaded ends of approved quality conforming to IS : 8931

(Make :- Essco-"Delux", cat. no.- ES 513 B)


131 Providing and fixing C.P. brass 'Health Faucet' with 8mm dia -1.0 meter long Flexible Tube and wall Hook - "Jaquar", 'Allied' - cat. no.- 573; also with Wall Bracket Swivel Hook - "Jaquar" - 'Allied' - cat. no.- 545 of approved quality conforming to IS : 8931

(Make :- Jaquar - "Allied", cat. No.- 573 & 545)


�

Documents

JOB SCHEDULE FOR CIVIL STRUCTURE - HPCLtenders.hpcl.co.in/tenders/tender_prog/TenderFiles/1457/Tender... · JOB SCHEDULE FOR CIVIL STRUCTURE FOR THE ZONAL OFFICE BLDG.(G+6 & ONE BASSEMENT)