MANUAL

John Deere 7600 - 7810

142585

Tractors

®

272 Industrial Drive, Box 830Regina, Sask. Canada S4P 3B1306 543-4447 543-2140 fx

degelman@degelman.com

www.degelman.com

SAFETY

142585

John Deere 7600 - 7810Tractors

The safety instructions that follow pertain only to this specific equipment. You should be aware of agricultural & industrial safety especially related to heavy equipment. If you are not familiar with safety procedures then you should get training.Improper use will result in maiming or death.

Blade, pivot frame 1

Cylinders & Hydraulics 3

Main Frame, Brackets, Mounting 5

Safety, Operation, Maintenance 9

Attachments 11

Warranty 12

®

p1

142585

®

John Deere 76-7810

Blade Components

24

12

25

10

23

22

11

15

14

14

13

13

2

2626

1

7

4

5

15

9 6

8

17

16

181920

3

p2

142585

Pivot Frame

21 781220 Pivot frame 1 22 781336 Angle cyl pin 4 23 118011 Bolt 1/2 x 1 1/2 4 24 118504 Lock washer 1/2 4 25 118587 Flat washer 1/2 4 26 117145 Wear bushing 1 1/2 6

1 781302 14ft 59 Dlock 1 781301 12ft 1 781300 10ft 1 2 781328 Bell 1 3 781326 Tilt ring 2 4 118051 Bolt 3/4 x 3 Gr. 8 6 5 117414 Locknut 3/4, Gr.C unitorq. 6 6 781370 Relief valve bracket 1 7 781340 Pivot pin, blade-pivot 1 8 118795 Bolt 5/8 x 2 1/4 2 9 118447 Locknut 5/8, Gr.C unitorq. 2 10 806014 Depth shoe 2 11 115402 Pin 4 1/8 2 12 118901 Lynch pin 2

13 116207 7ft Cutting edge 2 116206 6ft 2 116210 10ft 1 14 118204 Plow bolt 5/8 x 2 1/4 a/r 15 118447 Locknut 5/8, Gr.C unitorq. a/r

16 141524 Relief valve 1 17 118105 Bolt 5/16 x 2 1/2 2 18 118538 Flat washer 5/16 2 19 118530 Lock washer 5/16 2 20 118427 Nut 5/16 2

Qty

212425

22

2623

142585

®

John Deere 76-7810

Cylinders

p3

Tilt Cylinders

1 122552 Barrrel 1 2 122563 Piston 1 3 122558 Lock ring 1 4 122556 Open Cap 1 5 122560 Rod & Clevis 1 6 118441 Lock nut 7/8 UNF unitorq. 1 7 122670 Pin 1-1/2 x 2-3/4 2 8 118796 Shoulder Bolt 1/2 gr8 UNC 2 9 118924 Flat washer .59 ID x .9 OD 2 10 122523 Seal kit 1

122550, 3 x 8 x 1-1/2 Tilt cylinder Qty per cyl

Lift Cylinders

1 122652 Barrrel 1 2 122663 Piston 1 3 122658 Lock ring 1 4 122656 Open Cap 1 5 122660 Rod & Clevis 1 6 118441 Lock nut 7/8 UNF unitorq. 1 7 122670 Pin 1-1/2 x 2-3/4 2 8 118796 Shoulder Bolt 1/2 gr8 UNC 2 9 118924 Flat washer .59 ID x .9 OD 2 10 122522 Seal kit 1

122650, 3-1/2 x 8 x 1-1/2 Lift cylinder

781380 Lift Hydraulic Kit

Qty per cyl

781400 Tilt Hydraulic Kit

Angle Cylinders Qty per cyl

1 122602 Barrrel 1 2 122210 Piston 1 3 122558 Lock ring 1 4 122209 Open Cap 1 5 122206 Rod & Ball Joint 1 6 118441 Lock nut 7/8 UNF unitorq. 1 7 122212 Seal kit 1

122200, 3 x 20 x 2 Angle cylinder

781390 Angle Hydraulic Kit

Angle Cylinders (alternate)Qty per cyl

1 122602 Barrrel 1 2 122563 Piston 1 3 122558 Lock ring 1 4 122556 Open Cap 1 5 122606 Rod & Ball Joint 1 6 118441 Lock nut 7/8 UNF unitorq. 1 7 122523 Seal kit 1

122600, 3 x 20 x 1-1/2 Angle cylinder

781390 Angle Hydraulic Kit

1

23 4

5

6

7

89

7

89

10

10

1

2 34

5

6

7

89

7

89

1

1

2

2

3

3

4

4

5

5

6

6

7

7

142585

Hydraulics

p4

Qty

126578 Hose 3/8 x 9 2126605 Hose 3/8 x 18 2126579 Hose 3/8 x 204 2126548 Hose 3/8 x 50 4126553 Hose 3/8 x 216 4126585 Hose 3/8 x 25 2126542 Hose 3/8 x 27 6

Hose lengths ( ) in inches

1 141504 EL 3/4 m JIC x ORB 162 141501 TEE 3/4 m JIC 23 141515 Nipple 3/4 m JIC x ORB 24 141527 TEE 3/4 m JIC x JIC x ORB 45 141517 Connector 3/4 JIC m 66 141581 Quick coupler 6

QtyHydraulic Fittings

Use different coloured tape to mark sets of hydraulic hoses.Use one or two tapes to indicate lifting or retracting hoses.

133091 Coloured hose markers, 1 pack

1

4 5 6

2 3

TiltTilt

(25)(25)

(216)

(216)

(204) (204)

(216) (216)

(216)continued

(216) continued

Relief

AngleAngle

(50) (50)

(50)

(50)

(9)

(18)

(9)

(18)

Lift

Lift

Hose take-up

(204)continued

(204) continued

(27)(27)

TILT CYLINDERS

LIFT CYLINDERS

ANGLE CYLINDERS

1 14

4

4

4

1 1

11 3

3

1 1

2

2

1 1

55

5 55

5

16 6

66

66

11 1

11

p5

142585

®

John Deere 76-7810

1

2

3

4

5

67

7

10

8

9

11

1213

13

1415

16

17

18 19

Inside bolt bar-Upper row of holes

Hook hose take upto tractor frame

Front bracket& hanger

7th 9th 11th 13th

Main & rear framebolt hole alignment

2nd 3rd 4th 5th

Tractor's hyd ports at rear

p6142585

142585

Brackets & Components

1 780355 Main frame 1 2 780220 Front hanger 1 3 118048 Bolt 3/4 x 2 1/2 8 4 118422 Lock nut 3/4 8

5 780589 Front bracket 1 6 118747 Bolt M20 x 80 8 7 118551 Lock washer M20 8

8 780596 RH side bracket 1 780595 LH 1 9 118198 Bolt M20 x 70 16 7 Lock washer M20 16 24 10 118461 Nut M20 p8.8 16 11 780587 Block heater brkt 1 12 780210 Rear frame 1 13 118743 Bolt 3/4 x 2 1/4 16 14 118509 Lock washer 3/4 16 15 118410 Nut 3/4 16

16 780356 Pivot pin, main-pivot 1 17 118645 Bolt 5/8 x 1 1/4 1 18 118508 Lock nut 5/8 1 19 118514 Flat washer 5/8 1

20 780270 Hose take up 1 21 780274 Spring 1

Qty

Qty for that application & grand total for this assembly

21

20

Use these two holes & supplied side hanger brkt bolts to attach block heater brkt

Remove existing block heater brkt, discard & attached supplied block heater brkt inside tractor frame

LH side hanger

brkt

Tractor frame

Front

p7

142585

®

John Deere 76-7810

1 780145 Dlock linkage 2 2 118030 Bolt 5/8 x 3 2 3 780788 DL bushing 2 4 118448 Lock nut 5/8 2 5 780789 UHMW plastic block 2 6 243500 Lock pin 2 DL linkage includes.. 7 780143 Wedge 1 8 143116 Compression spring 1 9 118913 Roll pin 1 10 780146 DL linkage plate/bush 1

11 780150 DL handle 1 6 Lock pin 1 3

12 780273 Hose clamp 4 part 3 includes... 13 118144 Bolt 5/16 x 1 1/2 1 14 780279 Top plate 1 15 780278 Clamp two halves 1 16 780277 Bottom plate weld on 1

7

98

101

2

34

12

13

14

15

16

11

6

6

5

Qty

Qty for that application & grand

total for this assembly

Leave small gap

Line tractor up over the rear/main frames. Make sure DLOCK is open, clip pin is off and handle is stored.

Drive forward so that the front bracket pin is just behind the front hanger's hook. It should be lined up so you can drive into the front hanger when it is raised up. Hook up the hydraulics.

Raise the front hanger by extending the lift cylinders so the pin and hook are level.

Now close the lift cylinders. This will take the weight off the rear frame. Pry and jack up if necessary. Close the DLOCK.

Drive forward until the pin is in the front hanger.

Take clip pin off

Make sure Dlock is closed properly

To disengage: 1- RAISE THE BLADE 2- Open the Dlock 3- Extend lift cylinder to lower rear frame 4- Lower main frame to graund 5- Back out to clear front hanger 6- Unhook hydraulics

WARNINGIt is vital to raise the blade before opening Dlock.If you don't the rear frame will fall.

Dlock closing

Use the handle to close the latch

Note the second position for the final movement of closing

Secure with clip pinPut

handle away

142585

Mounting

YOU ARE RESPONSIBLE . . . for your own safety and that of others. If you are not familiar with basic agriculture & industrial safety, you must get training. Owners of equipment must by law give operating instructions to other operators such as family members or a hired hand.

Making any design changes to equipment could cause a hazard and damage your machine.

Wear proper safety equipment.

Have handy:

• First aid kit • Fire extinguisher

Before working on machine:

• Turn tractor off • Set controls in neutral • Remove ignition key

Keep all parts clean. Replace worn or damaged parts.Don’t try any makeshift repairs. Before operating check that everything is tight and not broken.

Wear gloves and eye protection when searchingfor leaks. Use a piece of wood or cardboard butnot your hand. High pressure oil will penetrate your skin. If that happens you risk serious injury.

Lower blade to the ground when not in use. Keep clear of blade when tractor is running. Keep hands & feet away from under blade. Turn engine off when hooking up hydraulics and engaging DLOCK during mounting or dismounting.

Lift blade up then hold with safety chain.Make sure SMV sign & reflectors are clean.Use your hazard lights.

• Lube all points• Torque all hardware to correct setting• Check hardware torque & hydraulics after

the first 2 hrs & again after 10 hrs.

Before using for the first time

Check:

• If all points lubricated• All components attached securely• Condition of cutting edge• Depth shoe wear• Tractor’s Hydraulic oil reservoir• Condition of hoses, lines & fittings

Before using each time Cycle the cylinders several times to warm up system.Cold weather

Check torque on all hardware periodically. Check after first 2, 10, 40, then every 200 hours.

IMPORTANT

Bleed hydraulics of air. Cycle the hydraulics several times and hold the cylinders at full extent for several seconds.

Bleeding hydIf needed, balance out your tractor by ballasting the rear end. You may need to raise the tire pressure in the front wheels. Consult your tractor's manual.

Rear end weights & Tire inflation

Here are some the things you can do with your hyd system in float position;

• Skim the top of pavement• Run on the skid shoes• Back drag

Floatation mode

all hardware

TORQUE

Why is SAFETY important to YOU?

•Accidents Can Disable and Kill•Accidents Are Costly•Accidents Can Be Avoided

142585

®

John Deere 76-7810

Operation & Maintenance

3 BIG Reasons:

p9

HYDRAULIC

BLADE

TRANSPORTING

Tilt cyl

Tilt cyl

Front brkt

Bell, 4 places

Angle cylAngle cyl

Lift cyl

Lift cyl

Tilt ring

Pivot pin, pivot/main frm Dlock

Pivot pin, blade/pivot

Front brkt

p10

Torque Settings

Lube both sides

Lube with: Grease

Spray lubricant

Lube all points and mechanisms after every 8 hr of use.

142585

1/4 9 12 5/16 18 25 3/8 30 45 7/16 50 70 1/2 75 110 9/16 10 155 5/8 155 215 3/4 270 385 7/8 435 620 1 660 930

Imperial Gr. 5

(ft lb)

Gr. 8

3/4 75 7/8 90

(ft lb)

Hyd. Fittings

3 0.4 1.3 4 2.2 3.3 5 4 7 6 7 11 8 18 26 10 37 52 12 66 92 15 66 228 20 321 450 24 553 774

Metric 8.8

(ft lb)

- SAE10.9

Operation & Maintenance

Depth shoesSoft uneven ground • Depth shoe low • Blade high

Hard even ground • Depth shoe high • Blade low

?NOTE: All hardware is Hex head, Plated, Gr.5 UNC (imperial) or P10.9 2.5 (metric) and all Hoses are 3/8, ends c/w 3/4 JIC female swivel, unless stated otherwise.

142585

®

John Deere 76-7810

Attachments

p11

1 118043 Bolt 3/4 x 2 a/r2 118516 Flat washer 3/4 a/r3 118509 Lock washer 3/4 a/r4 118410 Nut 3/4 a/r5 118539 Flat washer 3/4 a/r

Replacement Decals/Reflectors

Attachment Hardware

142386 Warning decal, Falling Blade 2142008 Degelman logo 25 3/4 lg 2142280 Red reflector 6 3/8 2142279 Amber reflector 3 1/4 lg 1142780 5900 blade decal 1

Silage extension 781570 14ft781560 12ft781550 10ft

1ft Extension781586 - Tworeq'd

Side plate 781540 - Two Req'd

Top extension 78160200 14ft781601 12ft 781600 10ft

11

5

1

3 4

12 3

1

34

4

13

4

1

3

4

5

5

Write down the following information about your dozer blade to better help you obtain assistance or service if you ever need it. You will need to know your model number and serial number. You can find this information on the model and serial number plate located on your dozer blade.

Degelman Industries Ltd. ("Degelman") warrants to the original purchaser of any new Degelman equipment, purchased from an authorized Degelman dealer, that the equipment will be free from defects in material and workmanship for a period of two (2) years from the date of delivery, for non-commercial use (including farm, institutional, government, and municipality) and (1) year from the date of delivery for commercial use. The obligation of Degelman to the purchaser under this warranty is limited to the repair or replacement of defective parts in the first year and to the provision, but not the installation of replacement parts in the second year. Degelman reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.

This warranty limits its replacement or repair coverage to what is consistent with the warranty of Degelman's suppliers of purchased components.

Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of delivery of such part or the expiration of the applicable new equipment warranty period, which ever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Degelman dealer during regular working hours. Warranted replacement parts will either be replaced or rebuilt at Degelman's discretion.

Disclaimer of implied warranties & consequential damages

This warranty shall not be interpreted to render Degelman Industries Ltd. liable for injury, death, property damage or damages of any kind, whether direct, consequential, or contingent to property. Without limiting the generality of the foregoing, Degelman shall not be liable for damages resulting from any cause beyond its reasonable control, including, without limitation, loss of crops, any expense or loss of labour, supplies, rental machinery or loss of use.

No other warranty of any kind whatsoever, express or implied is made with respect to this sale; and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale. This exclusion shall not apply in any jurisdiction where it is not permitted by law.

This limited warranty shall not apply:

1. If, in the sole opinion of Degelman, the unit has been subjected to misapplication, abuse, misuse, negligence accident or incorrect installation.2. To any goods that have sustained damage or deterioration attributable to a lack of routine maintenance (eg. Re-torque of mounting hardware.)3. If parts not made or supplied by Degelman have been used in the connection with the unit, if, in the sole judgement of Degelman such use affects its performance, safety, stability or reliability.4. If the unit has been altered or repaired outside of an authorized Degelman dealership in a manner which, in the sole judgement of Degelman, affects its performance, safety, stability or reliability.5. To expendable or wear items such as cutting edges, skid shoes, and any other items that in the company's sole judgement is a wear item.

No employee or representative of Degelman Industries Ltd. is authorized to change this limited warranty in any way or grant any other warranty unless such change is made in writing and signed by the Degelman Service Manager.

This limited warranty is subject to any future availability of supply, which may directly affect Degelman's ability to obtain materials or manufacture replacement parts.

Degelman reserves the right to make improvements in design or changes in specifications at any time, without incurring obligations to owners of equipment previously delivered.

This limited warranty is subject to compliance by the customer to the enclosed Retail Customer's Responsibility Under Degelman Warranty.

Dealer Name

Address

Phone Number

Model Number

Serial Number

Purchase Date

142585WARRANTY2 Year

Limited Warranty

0905Printed in Canada p12