Joining manual

8/11/2019 Joining manual

http://slidepdf.com/reader/full/joining-manual 1/6

Manual No. 32110Edition/da te : 9709.2/MGReplace s: 9709.1Autho rs : G ul/K/Ac

J oining sys tem

Flexproof

Joining manual

Spindle tape W-8

Please observe the following points when realizing

the joint:

Heed the type and width of the guide rail!

Tape width = guide rail width: Do not force the tape ends into theguide rail!

Install tape in such a way that the black side lies on the pulley orthe cylinder and the green one on the whirl.

After joining always check opt ical quality of the joint!

In ca se of q uestions and for supplementary literature a sk nearest Haba sit representation.




J oining s ystem

Flexproof P a ge 2/6

W-8

1Preparing

78 01

6 m m30 mm /1.18 in.

Ca refully rea d through the

opera ting instructions a nd

manuals.

Standard dimension of fingers

for W-8: 6/30 mm (0.24/1.18 in.)

02 03 04

Die-cutting device AF-30 Hea ting press PQ-54, P Q-57 Cooling tongs CD-54, CD-60

Used devices

0 . 2

4

i n .1 2

3a 3b 3c





J oining s ystem


4Hot-pressing

03

P lug in ca ble a nd hea t up

hea ting p ress until the ta rget

temperature has b een reached(at least 5 min).

Clamp hea ting press on guide

rail with inse rted ta pe.

Make sure that

guide rail lies

perfectly centeredin the press.

Tape width 6-13 mm / 1 / 4 - 1 / 2 in . (narrow guide rail)

Set pressing time to 120 sec.

and w a it till time has expired.

After expiry o f the pres sing time in

the heating press, remove heating

press from the g uide rail.

Set cooling time to 120 sec. and

wait till time has expired.

Immediately clampcooling tongs onguide rail!

W-8

12 13

14

HR MIN SEC

START

STOP RESET

Set

Timer

HR MIN SEC

START

STOP RESET

Set

Timer

15

HR MIN SEC

START

STOP RESET

Set

Timer

HR MIN SEC

START

STOP RESET

Set

Timer


Tape width 15-35 mm /5 / 8 - 1 3 / 8 in . (wide guide rail)

Set pressing time to 180 sec.a nd w a it till time ha s expired.

After expiry o f the pres sing time inthe heating press, remove heating

press from the guide rail.

Immediately clampcooling tongs onguide rail!

Set cooling time to 180 sec. andwait till time has expired.

11

15

14

12 13



J oining s ystem


4Hot-pressing (continued)

17

After cooling is completed

remove ta pe from guide rail

by steadily pulling.

Let the tape cool off to room

tempera ture outs ide of hea ting

press.

5Quality check of the joint

J oint is o k.After the tape has cooled

do wn, chec k the joint q uality.

Ca refully cut o ff tape ma terial

that has o ozed o ut with

scissors.

1. Penetration too strong

→ reduce p ressing time.

Careful!Do not damage tapeand tape edges!

Holes a nd ga ps

→ ma ke sure that finger tips

indent closely.

Finger tips sticking off

→ die-cut more precisely.

18 19 23

W-8

16


2. Penetration too little→ increas e press ing time.

222120

16 17

201918

21 22 23

1

2



Documents

Joining manual