JS5016 Data Convergence Gateway Operation Guide V1.0

7/26/2019 JS5016 Data Convergence Gateway Operation Guide V1.0

1/15

JS5016 Data Convergence Gateway

Operation Guide

JIASIN INDUSTRY CO., LTD, ZHUHAI


2/15

Product nameJS5016 Data Convergence Gateway Operation Guide (V1.0)

Al l r ights reserved

JIASIN INDUSTRY CO., LTD, ZHUHAI


3/15

JS5016 Data Convergence Gateway Operation Guide

1 12

In a following part of th is document, we take the following scheme

diagram, for example:

1. Firstly get the device IP address---(If you has known the IP address please

directed skip to the JSNetView operation section)

JS5016 data aggregation gate supports NMS based on Console serial port. Youcan query the device IP address by connect the Console port on device with a

computers serial port.

1.1 Setting up a Console connectionConnect the DB9F end of serial NMScable to the computers serial port and the other RJ45 end connects to theCONSOLE port on the equipments rear panel.

1.2You can use a variety of terminal software; here we use HyperTerminalin Windows accessories for an example. Click the computer's Start menu,select Programs Accessories communication HyperTerminaloptions


4/15


2 12

1.3 Make sure the equipment and the computer has connected properly,and then selects the correct COM number, as shown in the followingfigure

1.4 Setting the Hyper Terminals parameters, the baud rate set to 115200(baud rate can be modified, the factory default value is 115200bps),and the data bit set to 8, the parity set to None, the stop bit set to1, the data flow control set to None. as shown in the following figure.


5/15


3 12

1.5 After the serial port parameters have been set, click OK button toenter the terminal control interface.

1.6 Press ENTER key, it will appear root login, input user name admin

and press ENTER key again, it will appear password, the factorydefault password is blank, hit the press key to login the equipmentsCLI operation interface directly. Enter shownet to get the device IPaddress.

The default IP address is 192.168.1.11.

2.JSNetView NMS operation and parameters configuration

2.1To create a device icon, right click on any blank place at the topology interface

and select New > JS5016.


6/15


4 12

2.2Right click on the device icon and select Properties to modify the device

attribution, modify the IP Address and click OK button.


7/15


5 12

2.3 Double click the device icon to enter the device managementinterface.


8/15


6 12

2.4 Only need to configure the working clock and leave other

parameters to default setting. See the parameters configuration of

System Parameter in the following figure.

2.5 All the E1 Parameters use the default configuration.

.


9/15


7 12

2.6 Configuring the parameter of HDLC to assign the bandwidth for the two

JS10Bs.

2.7 To create a device icon, right click on any blank place at the topology

interface and select New > JS10B.

2.8 Connect JS5016 with JS10B.


10/15


8 12

2.9 Connect the first JS10Bs icon with the second JS10Bs icon.

2.10 Set ID for the two JS10B devices.


11/15


9 12

2.11 Select network side E1 clock for the first JS10B device.


12/15


10 12

2.12 See the configuration of E1 information in the following figure.

2.13 Assign the bandwidth for the Ethernet port of the first JS10B.


13/15


11 12

2.14 The Loop Test dont need to configure.

2.15 Assign the bandwidth for the Ethernet port of the second JS10B.


14/15


12 12

Refer to above steps to realize JSnetview login, JS5016 login, JS10B login , and

service parameters configuration.


15/15

If you have any query in the course of use, please contact with our

technical service center.

Company consultation & service center after sale

Address 3F Bldg B1,Southern Software Park,No.1 Software

Road,Zhuhai,Guangdong,P.R.China

Postcode519080

Tel0086-756-8529777, 8529037

Fax0086-756-8529555

[email protected]

Documents

JS5016 Data Convergence Gateway Operation Guide V1.0