Owner's Manual

ThisOwner's Guide providesspecific operating instructionsfor your model. Usethe airconditioneronly as instructed in this guide. Theseinstructions are not meant to coverevery possiblecondition and situation that may occur, Common senseand cautionmust be practiced when installing, operating, and maintaining any appliance,

Record Your Model and Serial NumbersRecord in the space provided below the model and serial numbers. The sedal plate islocated on the outside of the cabinet, or behind fitter at the bottom of unit. Readingthe numbers may be easier by using a flashlight or by removing the cabinet front asinstructed under "Care and Cleaning."

Model Number.

Serial Number.

Purchase Dat.e:

P/N 309000845 (1/02)

i

///g/n0I

J Important SafetyInstructions

Avoid fire hazard orelectric shock. Do not use an extensioncord or an adaptor plug. Do not removeany prong from the power cord.

Grounding type

wall receptade

under

Power supply

cord with 3-proncgrounding plug

Read all instructions before using this air conditioner,

For Your SafetyDo not store or use gasoline or other flammable vapors and liquids in the vicinity ofthis or any other appliance. Readproduct labels for flammability and other warnings.

Prevent AccidentsTo reduce the risk of fire, electricalshock, or injury to persons when using your airconditioner, follow basic precautions, including the following:• Besure the electrical service is adequate for the model you have chosen.• If the air conditioner is to be installed in a window, you will probably want to

clean both sides of the glass first. If the window is a triple-track type with ascreen panel included, you may want to remove the screen completely beforeinstallation.

• Be sure the air conditioner has been securely and correctly installed according tothe separate installation instructions provided with this manual. Save thismanual. Save this manual and installation instructions for possible future use inremoVing or reinstalling this unit.

• When handling the air conditioner, be careful to avoid cuts from sharp metal finson front and rear coils.

Electrical InformationThe complete electrical rating of your new room air conditioner is stated on theserial pl:_te. Refer to the rating when checking the electrical requirements,

• Be sure the air conditioner is propedy grounded. To minimize shock and firehazards, proper grounding is important, The power cord is equipped with athree-prong grounding plug for protection against shock hazards.Your air conditioner must be used in a properly grounded wall receptacle. Ifthe wall receptacle you intend to use is not adequately grounded orprotected by a time delay fuse or circuit breaker, have a qualified electricianinstall the proper receptacle.

• Do not run air conditioner with outside protective cover in place. This couldresult in mechanical damage within the air conditioner.

_r Do not use an extension cord or an a_apter plug.

I I

Energy Saving Ideas • The capacity of the room air conditioner must fit the room size for efficient andsatisfactory operation.

• Install the room air conditioner on the shady side of your home. A window thatfaces north is bestbecause it is shaded most of the day.

• Do not block air flow inside with blinds, curtains or furniture; or outside withshrubs, enclosures, or other buildings_

• Close the fireplace damper, floor and wall registers so cool air does not escapeup the chimney and into the duct work.

• Keep blinds and drapes in other windows closed during the sunniest part of theday.

• Clean the air filter as recommended in the section "Care and Cleaning."• Proper insulation and water stripping in your home will help keep warm air out

and cool air in.• External house shading with trees, plants or awnings will help reduce the air

conditioner's work load.• Operate heat producing appliances such as ranges, washers, dryers and

dishwashers during the coolest part of the day.

How and WhyYour room air conditioner provides the following functions to make hot weatherliving more comfortable:

6_o Cools and circulates room air.Lowers humidity by removing excess moisture. High moisture levels maycause the air conditioner to drip excessmoisture outside.

• Filters out summertime dust, dirt, and some airborne impurities. mThe air conditioner performs these functions by drawing room air through a filterwhich traps dust and dirt particles. The air then passes over a cooling coil which 8refrigerates the air and removes excessmoisture. The same air is then returned tothe room -- cooler, drier and cleaner. Moisture removed from the room air is carriedto the outside and evaporated. This moisture may form ice on the inside coi! if theoutside temperature is below 65 degrees. Setting the air conditioner on HI, FANONLYwill defrost the coil.

Your air conditioner is designed to be easy to operate and to provide plenty of

cooling power. Your air conditioner is also more efficient than (most) older modelsand may run longer to cool the room, but will use tess energy due to igher energyefficiency ratings.

Capacity andRunning Time

Proper unit size is important in deciding the desired comfort for the area you wantto cool. The proper size is determined by the number of square feet in the area tobe cooled.

Whenever the heat or humidity load is above normal the air conditioner must runlonger and more often to keep the desired temperature you have selected. Underheavy heat load conditions the air conditioner may need to run constantly to keepthe temperature you want. Allow some time to cool the room if the air conditionerwas recently turned on. Using the "AUTO START" feature will allow you to startcooling the room prior to returning home.

At times using the HI Fan setting to circulate the room air may make it comfortableeven though you do not have the air conditioner set to cool the air. This willdecrease your cost to use.

Normal Sounds

Sound of Ru,sbin# AirAt the front of the unit,you may hear the soundof rushing air being movedby the fan.

SoundAs cooling systems cycle onand off, you may hear a"clicking" sound.

I_ Troubleshooting Tips t

High Pitched ChatterToday's high efficientcompressors may have ahigh pitched chatter duringthe cooling cycle.

Unit may vibrate and makenoise because of poor wallor window construction orincorrect installation.

f_n£im, or Swisbin_Droplets of water hittingcondenser during normaloperation may cause"pinging or swishing"sounds.

"Gurglingor hissing"noise may be heard due to refrigerantpassing through evaporationduring normaloperation.

3

I

Front InstallationSome models are shipped in a removable sleeve, please follow the suppliedInstallation Instruction before installing the Decorative front and accessories.

Installing the Vent Control (on some models)The vent control handle is included in the decorative front kit. The handle must beinstalled before the decorative front is attached.

I. Insert the handle with the "etchings (VentlAir)" facing to the left.2. Slip the black door extension into the split at the end of the handle.3. For ease of assembly, push the handle in while pressing the door extension

against the foam until the two pieces lock together.4. Move handle in and out to be sure vent is operating properly.

Installing the Front FrameSome models requireinstallation of the front panel of the air conditioner includedin a decorativekit. Toassemble,follow these steps. Before installation, remove thetilt panel from the frame. Grasping the panel from both sides, gently pull to release,then lift panel from pivot points at bottom of frame (Fig, I).

STEP 1: INSTALL DECORATIVEFRONT TO CABINET:

FIG. 1

• Position the top of the decorative frontover the top flange of the case, and align the tabs with the slots in the case(Fig. 2).

• As you install the front frame tothe unit be sure the vent handle ispositioned through the front in theproper location (Fig. 3).

• Carefully pull down on the front toengage the top tabs, while pushingthe front over the caseto ensureproper alignment.

• The side tabs will "click" whenfront is seated.

• Install front retaining screw(s)behind the filter and panel (Fig. 3).

• Then add filter and front panel.VENT

LE

SCREWS

FIG. 2

FIG. 3

Using Air Conditioner

NOTE: If the air conditioner is turned offor the temperature is changed to a lowersetting then back to a higher setting thecompressor will shut off. Wait 3 minutesbefore the compressor will restart, thisallows for the pressure inside thecompressor to equalize.. Failureto wait 3minutes may cause inefficient operation.When adjusting the temperature the fanwill continue to run.

To reduce the risk of fire, electric shock, or injury to persons, readthe IMPORTANTSAFETYINSTRUCTIONSbefore operating this appliance.

To begin operating the air conditioner, follow these steps:

1. Plug in the air conditioner. (Toprevent electricaIhazards, do not use an extensioncord or an adapter plug.)

2. Set the exhaust vent to the CLOSEDposition.3. Press"On/Off" button to turn unit on.

4. PressFan Speed "Ht"5. PressMode "COOL"

6. Press"TEMP/TIME" down v to the lowest setting "60 degrees"

7. Adjust the louversfor comfortable air flow.

8. Once the room has cooled, adjust the "TEMP/I"IME" and Fan Speed to desiredtemperature.

Review the "Air Conditioner Features" section for other settings.

Air Conditioner Features ELECTRONIC CONTROL OPERATING INSTRUCTIONSBefore you begin, thoroughly familiarize yourself with the control panel and remoteas shown below and all its functions, then follow the symbol for the functions you

ON/OF_ desire. The unit can be controlled by the touch pad alone or with the remote.

LOWERS DISPLAYS

TEMPERATURE _ TEMPERATURE/TIMEoR'rIME

RAISES

TURNS UNITON OR OFF

SETSJ

SPEEDS

OR "NMES

REMOTE CONTROL

Slip battery cover off and pull the piece of plastic from betweenthe battery end and the connector.

PIECE

Air Conditioner Features(continued)

STEP 1 -- TO TURN UNIT ON: YOU WILL SEE:

DO THIS:

PRESSON/OFFPAD

STEP 2 -- TO CHANGETEMPERATURE SETTING: YOU WILL SEE:

DO THIS:

TO RAISE

TO LOWER

Note: Tap or hold either up(A) or down(v) button until the desired temperature is seen in screen. This temperature will beautomatically maintained anywhere between 60F (16C) and 90F (32C). If you want the display to read the actual roomtemperature, see step 5.

STEP 3 -- TO CHANGEFAN SPEEDS:

YOU WILL SEE (WHICHEVERYOU HAVE CHOSEN):

PRESSTO SELECT

STEP 4 _ TO USEAUTO COOL FEATURE: YOU WILL SEE:

DO THIS:

Note: The fan speed will begin in HI. then adjust to MED and LO as the room temperature conditions dictate. For example, ifthe room doesn't get too warm it will stay at LO. ff the room temperature rises quickly, such as a door being opened, it willautomatically go to HI speed. The fan speeds will readjust back to LO as the room returns to the original set temperature.

6

Air Conditioner Features(continued)

STEP 5 -- TO OPERATEON FAN ONLY:

DO THIS:

PRESSON(if not running)

PRESSFAN ONLY

YOU WILL SEE:

Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air.(remember toopen the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fanspeed you prefer.

During this function, the display will show the actual current temperature, not the set temperature as in the cooling mode.

STEP 6 -- TO USE THE POWERSAVER FEATURE: YOU WILL SEE:

DO THIS:

PRESSPOWERSAVER

Note: In this mode, when the compressor shuts off, the fan will continue to run for another 3 minutes, then shut off untilcooling is needed, as sensedby the room temperature control. During this time, it may come on for 3 minutes to sensewhethercooling is needed, then it will go off for 10 minutes. It will continue doing this to sample the room air for as long as necessary.

STEP 7 -- TIMER-DELAYSTOP FEATURE YOU WILL SEE:

DO THIS:

PRESS

PRESS

Note: The unit must be running to make this setting.

Proceed as in step 9 to change the desired number of hours, before the control will time out and turn off.

Air Conditioner Features(continued)

STEP 8 w TIMER-DELAYSTART FEATURE: YOU WILL SEE:

DO THIS:

PRESSOFF(If unit is running)

PRESSTIMER/OFF

Note: To do this, the unit must be in the off position.

When first set, the display will show .5. (one half hour),to increasethe time up to 24 hours, go to step 9,

STEP 9 -- TO INCREASEDELAYED START TIME: YOU WILL SEE TIME CHOSEN:

DO THIS:

PRESS

Note: Tap or hold the UP arrow(A) to increase delayed star,_time by .5 hours (up to 10 hours), then in 1 hour increments upto 24 hours. The control will count clownthe time remaining until start (8, 7.5, 7, etc.).

The unit will then come on in Cool and HI fan mode. The temperature maintained will-be the same as you previsouly set. If youwant to change it, Press'Cool" or "PowerSaver Mode" pad, whichever you desire, then Up or Down arrows until the desiredtemperature is indicated on the display. Pressingtimer "On/Off" or after 5 seconds, the control will automatically change thedisplay back to the hours remaining until the unit will start.

Switching unit on at any time will nullify this setting.

STEP 10 w SLEEP FEATURE: YOU WILL SEE:

DO THIS:

PRESSON/OFFPAD

Note: In this "MODE" the selected temperature will increase by 2 degrees F 30 minutes after the mode is selected. Thetemperature will then increase by another 2 degrees Fafter an additional 30 minutes. This new temperature will be maintainedfor 7 hours before it returns tO the originally selected temperature. This ends the "Sleep" MODE and the unit will continue tooperate as originaUy programmed. The "Sleep" MODE program can be cancelled at any time during operation by pressing_Sleep" MODE, "On/Off", "Fan Only" or the "V //X" buttons, on either the Control or the Remote. "Time Delay Stop"limit reached will also end "sleep" MODE.

8

L

Air Conditioner Features(continued)

STEP 11 -- CHECK FILTERFEATURE:

DO THIS:

PRESSTO RESET

YOU WILL SEE:

Note: This feature is a reminder to clean the Air Filter (SeeCare and Cleaning) for more efficient operation and cooling. TheLED(light) will illuminate after 25Q hours of operation, whether in cooling or fan only. To reset after deaning the filter, pressthe "Check Filter" button and the light will go off, This will restart the 250 hours, this timing cannot be reset unless the LED(light) is on. This feature cannot be reset with the remote.

STEP 12 -- TO TURN UNIT OFF: YOU WILL SEE:

DO THIS:

PRESSON/OFFPAD

Air Conditioner Features(continued)

ADDITIONAL THINGS YOU SHOULD KNOW

Now that you have mastered the operating procedure, here are more features in your control that you should become familiarwith.

• Remote control works exactlylike the control panel, follow the same instructions.

• The "Cool " circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This preventsoverheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.

• The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and gOFdegrees.

• Any sudden power failure will causethe letters "PF" to flash in the display. Touching any pad twice will restore the unit tothe previous function chosen.

Figure 1 (OFF)

Figure 2 (FRESHAIR)

Figure3 (VENT)

Fresh Air Vent Control

The Fresh Air Vent allows the air conditioner to recirculate inside air (OFF), drawair into the room (FRESHAIR) or exhauststale air to the outside (VENT). SeeFigures1, 2 & 3 for this operation.• The "OFF" position is used when MAXIMUM cooling is desired. It may also be

for room air re*circulation without cooling when the selector switch isset to theFANposition, this will also filter the room air.

• The FRESHAIR position allows outside air to be drawn into the room to refreshthe inside room air.

• The VENTposition removes stale air from the room and exhausts it to theoutside.

• Any vent position can be used with any fan selection.

10

Air Conditioner Features Air Directional LouversAir directional louverscontrol air flow direction. Your air conditionerhas the louver

(continued) type described beiow.

(4 WAY)

&.Way LouversThe 4-Way air directional louvers allow you to direct air flow up or down, left orright throughout the room as needed. To adjust the air directional louversside-to-side, use the center handle as you move it side-to-side.

Care and Cleaning Clean your air conditioner occasionally to keep it looking new. Be sure to unplugthe unit before cleaning to prevent shock or fire hazards.

Air Filter CleaningThe air filter should be checked at least oncea month to see if deaning is necessary.Trapped particles in the filter can build up and cause an accumulationof frost onthe cooling coils.• Grasp panel from either side just below the air directional louvers and gently pull

to release the top edge of panel.• Gently pivot the panel on its hinge.• Grasp filter and remove. Snap panel back into place.• Wash filter with warm soapy water. Rinsethoroughly. Gently shake excesswater

from filter. Be sure filter is thoroughly dry before replacing.Or,Instead of washing you may vacuum the filter clean.

• Open the panel as before and reinstall the filter.

iCabinet Cleaning• Besureto unplug the air conditioner to prevent shock orfire hazard.Thecabinetand

front may be dustedwith an oil-freecloth or washedwith a cloth dampenedin asolutionof warm water and mild liquid dishwashingdetergent.Rinsethoroughly andwipe dry.

• Never use harsh cleaners,wax or polish on the cabinet front.• Be sure to wring excesswater from the cloth before wiping aroundthe controls.

Excesswater in or aroundthe controlsmaycausedamageto the airconditioner.• The cabinet front can be removed for more thorough cleaning.Referto "Front

Installation" in this manual• Clean the front in a sink using liquid dishwashing detergent and warm water. Rinse

thoroughly and dry.• Replacecabinet front. Replacethe screws.• Replacefront panel (if applicable) and filter. Plug in air conditioner.

11

Routine Maintenance Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully fromthe window according to the installation instructions. Cover it with plastic or returnit to the original carton. NOTE:To prevent rust or electrical connections frombeing damaged, store air conditioner in an upright position and a dry place,A winter cover can be purchased from your dealer.The cover will protect the airconditioner when it is left in place through the winter,

Before performing any service, unplug the power cord fromthe electrical outlet

After servicing, reversethe following procedures to reinstall the air conditioner.

Cleaning the Cabinet Front

Remove the front panel. Wash with warm, sudsy water. Rinse and dry witha softcloth. Never use solvents, cleaning fluids, abrasive cleaners or strong detergents. Ifthe packaging leavesa gum residue, remove with a cloth dipped in rubbing alcohol.

Repairing Paint Damage

Inspect weather-exposed parts (cabinet shell, mounting hardware, if used, etc.)once or twice a year, especially in areas near oceans or where rust is a problem. Ifneeded, touch up with a good grade of exterior paint.

Cleaning Inside the Air Conditioner

No liquid should get into the motor, electrical control box, orcompressor electrical terminals.

1. Remove front panel.

2_ With help and using the proper lifting methods to avoid personal injury, removethe chassisfrom cabinet shell.* When removing the air conditioner from cabinetshell or window, there may be water insidethe base that may spill on the floor.Be careful to avoid cuts from sharp metal fins on the front and rear coils.

3. Liquids should not get into electrical parts. Warp the fan motor, electrical controlbox, and electdcal terminals in plastic. This will keep water or other liquid fromgetting insidewhere it could damage the insulation and cause serious trouble.

4. Clean and hose out base, coils, and water pans. Clean at least once a year ormore often if the coils and pans collect dirt, sand, leaves, algae, or insects.

5. After cleaning, remove plastic protection. Wait 24 hours before starting the unitagain. This allows time for all areas to dry out.

NOTE: Water from rainfall or from normal use does not harm these componentssince the water is not asforcefully driven into parts as a stream of water from agarden hose.

*HANDLE NOTE: If the air conditioner has a chassis handle, it is NOT intended for liftingthe unit. it is for sliding the chassis WITHIN the cabinet shell only (to aid in cleaning,maintenance, etc.).

12

,9Room Air ConditionerTroubleshooting Guide

_ THEAIR CONDITIONERWILL NOT OPERATE

O

Check If ...Powersupplycord_ disc0nnectod.NO_efusehasblown or circuitbreakertril_Pov_rLsGFE

Terrlperetu_setting• warmerthan morntemperatureUnitwasturned OFFandON too quickly.

TimershutunitOFF.

Thlll3 .,.Fi_ly pushTr,e cordinto a livewallout_ with propervoltage,(Pa,pe2)Replacethe fusewith a lime delay_ or resetthe circuit.(Page2)PushON/OFFBuffonto turn unit ON.(Page5)Settemperatureto a lowerset_n_ (Page6}POWERSAVEteatun doesnotcirculateair continuallySetmodeto COOLfor constantair circulation.(Page7)P_h ON/OFFButtonto turn unitON,(Paqe5)

THE AIR CONDITIONER BLOWS FUSES ORTRIPS CIRCUIT BREAKERCheck If ... Then ...Housefusehasblown orcircuitbreakertnpped. Replacethe ft_ewith a timedelaytypeor resetthe circuit (PageR)Toomanyelectricaldevicesarebein9 usedon the sameOrcuit. Unplugor relocateelectricalde_cesbeingsharedon samecircuit. (Page2)Unit isratedover 7.5 amps. Unitshouldbe pluggedinto a sln_lecircuitoutlet. (Page2)Und ispluggedinto an extensioncord. )o not usean extensioncordto run the unit (Pa_e2)Unitwas_rned OFFand ONtoo quick!,/ urn unitOFFandwart3 minutesbeforerestarting.(PageS)

rHEAIR CONDITIONERTURNS ONAND OFF BY ITSELFCh_-k If ... Then ...Outsidetemperatureisextreme_hot. Setfanspeedto HIto assistcoolingof unit (Page8)POWERSAVEfeature ison. POWERSAVEteatufedoesnotcEcutatoaircontinually.Setmodeto COOLforcorstant air circulabon.

{Pa_e7]TimerturnedunitONor shutunit OFF PushON/OFFButtonto turn unit ONorOFF!PapeS)

THE AIR CONDITIONER DOES NOT COOLTHE ROOM - ICE BEHIND FRONT PANELTh6r, ,.,

OutsideChq_ktemperaturelf.., isbelow 6OF Setmodeto FANONLYandfanspeedto HIto defrostcoil,.(Page3}

, _er isditty. Open frontpanel.Removefi,lter.Rinseor vacuumfilter.Replacefilter.ClosePanel.(Page1O)BTUslaeis too la_e. A lower capaotyunitmaybe requreddependng onthe sizeof the roombeir_ cooled (Pa_e3)

THE AIR CONDITIONER DOES NOT COOLTHE ROOM - NO ICE BEHIND FRONT PANELCheck if ...Fitterisdir_.Temperaturese_ng iswarmerthan morntemperature.Roomtemperatureisbelow 60EFrontof unit isb_ockedbyfurniture,drapes,blinds,etc.Rackof unit isblockedby leaves,dirt, branches,etc.Doors,w_ndow_,repLiers,etc.areoFen_Unitr_a_ntlyturned on.Temperaturesensoris touchingthecoil.

EJu:ess_heat inthe roomb_ng cooled

Openfront panel.Remo_ fleer.Rinseor vacuumfitter. Replacefilter,ClosePar_l(Page10)

Settemperatureto a lowersetting.(Page6)UnitIsnot designedto cool below_ (Page6)Clearaway'areain front of unit (Page2)Clearawa_backof unit.(Page2}Ctosedoors,window, re_'tors,etc. (Pa_e2)Allowtimetocoola lar_ericon. (Pag_3}Openfrontpanel.RemovefiEecTurnendof temperaturesensorawayfromcoil.ReplaceflRer.Closeanel. (Page10)

Useexhaust_r_ whilecookingor bathing. Limituseof heatproducingappllance_duedg_the_ttesl= partof theday+(Pa_ 2)o Ventcontrolis pulledopen. Pushinventcont_l for maximumcoo_inq.(i;ape9)

_ THEAIR CONDITIONER RUNSTOO MUCH

I_ If...

I_h pitd_ hornor pulset_r_no_ethe_cycleson andoff.o RushingairSound.1 J_ging or sw_hinq_ounds.

_ Gu_linq or hissingsounds.,. I_._.

I _ If ... Then ...

_ CurrentUnitreplacedan OlderunJl. Newer,isle_ duehighertohigheref&:ienCYeffidency,AtrCondEmner(pageg) mayrun$onger.to cool the room,.Tota_energyconsurnpBon

_ Bru s_e istuol smaI_ A higberca_adt'/unitnay be tequimdde_endingon thesizeof the t_ombein_jcooled(page3)

WATER DRIPPING FROM AIR CONDITIONER - INSIDE ROON

I l_heck If,,. Then .,.UnE isnotproperlyinstalled. Unitshouldbe mountedon a 1/4" downwardslopeto the outside(1/2bubbleona carpenter%level)I

:_ to provideproperdrainage.ReposEionor shimcabinetasneces_ani,DONOTdrill drainpan.WATER DRIPPING FROM AIR CONDITIONER . OUTSIDE ROOMI Check If .., ]Then ,..[ Roomishot and humid. [Normaloperat_nduringhot andhumiddays.(Page3)

.,_ THE REMOTE WILL NOT OPERATE AIR CONDITIONERCh_-k If .,. Th_n ...Batterie_arenotinstalledprope_. Verifythe pla_cshippingstrip is removedfromthe batteriesand the batteriesare installedproperly.

(PageS)

RedLigh_doesnot flashon the nlmotewhen the remotebu_onsam pushed Verify_ plasticshippingstlip is remo_d from the batter_ and _e batte_ ale installedproperly.,. Installa newsetof belted_s.(Pa_e5),Themrrtoe isp_nted at the unit Theremotemaynot workpmpe_ when usedat extremeangestothe fronto the unit Pa_eS

TYPICALAIR CONDITIONER SOUNDSYOU MAY HEARThe,.Compressor- Normalnoisedueto modernhigheff*dencyconlpresso,rs.(Page3)

_FeaI Moto_- Normalnoiseof highereflic_ne/fanspushir_Jalr furt_ Into the room.(Page3)Con

denser-Normalnor_of water hittin_the condemerto increaseener_ eff_ienc_.(Page3)Evaporator- Norrna_no,aeof _fn_e_et passin(jthroughevaporation.(Page3)ElectronicContlol - Normalnoisewhenelectroniccontrol set_n0samchanged.(Pa_e3)UnitVibfalcon- Dueto poorwa I or windowco--on or ncorrectnstalletion.IPaqe3)

13

WarrantyWARRANTY

Full One-Year Warranty on Air Conditioner

For one year from date of purchase, when this air conditioner is operated andmaintained for normal room cooling according to instructions in this owner'smanual, Searswilt repair iL free of charge, if defective in material or workmanship.

Full Five-Year Warranty on Sealed Refrigeration System

For five years from the date of purchase, when this air conditioner is operated andmaintained for normal room cooling according to instructions in this owner'smanual, Searswill repair the sealed refrigeration system (consisting of refrigerant,connecting tubing, and compressor), free of charge, if defective in material orworkmanship.

Warranty Service

Warranty service is available by contacting the nearest service center in the UnitedStates,

Thiswarranty gives you specific legal rights, and you may have other rightswhich vary fromstate to state.

SEARS, ROEBUCKand CO. Dept., 817WA, Hoffman Estates, IL 60179

Sears Service Maintenance Agreement

"We ServiceWhat We Sell" is our assurance you can depend on Searsfor service.Your air conditioner has added value when you consider that Searshasservice unitsnationwide, staffed with professional technicians trained on all appliances Searssells.They have the knowledge and skills, tools, parts, and equipment to insure ourpledge to you that "We ServiceWhat We Sell."

Sears Maintenance Agreement

Maintain the value of your air conditioner with a Sears Maintenance Agreement.Sears air conditioners are designed, manufactured, and tested for years ofdependable operation. Yet, any modern appliance may require sercicefrom time totime. The SearsMaintenance Agreement offers you an outstanding serviceprogramfor your air conditioner.

iThe Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's price.

• Eliminates repair bills resulting from normal use.

• Allows for as many service calls as required.

• Providesan annual Preventive Maintenance Check at your request to keep yourAir Conditioner in proper running condition.

For more information, call 1-800-827-6655

14