Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
KLEENGUARD* Protective clothing
3
Protective clothing legislationProduct selector
A comprehensive range of apparel products providing the most appropriate personal protection to meet your needs.
Selecting the right apparel To increase productivity and cost-effectiveness, workers must be able to work comfortably and safely, being protected against a broad spectrum of possible hazards. Use the apparel selector in order to determine the right garment for the right task.
The selector is a guide only. It is the responsibility of the employer to make sure the apparel is suitable for its intended use. We suggest that you always check the latest version of KIMBERLY-CLARK PROFESSIONAL* product literature to get more information about the products.
A40 A70/A71 A71 A20/A30/A40 A70/A71
YES
YES
NO
LIQUIDS PARTICLES
SPLASH
WATER-BASED SOLVENT-BASED
1 or40% or 40%
A70/A71 A70/A71 A40 A10
YES NO
Anti-static or low-lint requirement?
Anti-static or low lint requirement?
For more information, please visit www.kcprofessional.com
4
European guidelines within the CE Complex category help users identify the correct garment for the task. This information enables you to decide which product is suitable for your use.
To display the relevant Type Classification, as KIMBERLY-CLARK PROFESSIONAL* does, the manufacturer must test the garment to accepted European norms and have these results validated by an external certification body.
CE 0120 Assured KIMBERLY-CLARK PROFESSIONAL* has been accredited the CE mark of Complex design (Category 3) for its A20+, A40 & A71 KLEENGUARD* Protective apparel clothing by SGS Weston-Super-Mare United Kingdom Certification Services Ltd (EC Notified Body Number 0120). This was achieved by satisfying the examiner that products and quality systems meet the levels required by EU legislation.
KLEENGUARD* Protective clothing Protection Level SymbolsKIMBERLY-CLARK PROFESSIONAL* product identity system includes:
• StandardsymbolstoindicateproductsmeetingorexceedingtherequirementsofspecificEuropeanstandards• Multi-lingualuserinformation• Packagingtoprotectgarmentsuntiluse
Type 1 Gas tight clothingType 2 Non gas tight clothingType 3 Liquid tight clothingType 4 Spray tight clothing
Type 5 Particle protectionType 6 Limited splash protectionPB[6] Partial body protection
Body measurements (cm)
Size Height Chest
S 164-170 96-104
M 170-176 104-112
L 176-182 112-120
Size Height Chest
XL 182-188 120-128
XXL 188-194 128-136
XXXL 194-200 136-144
KLEENGUARD* Protective Garments such as A20+, A40 & A71 conform to EN 340 recommendations for sizing. Use the chart to help you select the right size garment.
EN 1073-2:2002Radioactive dust
contamination protection
EN 1149-1:1995Antistatic
CE0120 EN 14126:2003Infective agents
protection
EN ISO 13982-1:2004 Type 5
Particle protection
EN 14605:2005Type 3
Liquid tight clothing
EN 14605:2005 Type 4
Spray tight clothing
EN 13034:2005 Type 6
Limited splash protection
2
1
A20
2
1
A70
2
1
A80
2
1
A45
2
1
A40
2
1
A50
2
1
A10
2
1
Protective clothing legislationThe legal responsibilities
For more information, please visit www.kcprofessional.com
(1)
5
A comprehensive range of protective clothing products providing the most appropriate personal protection to meet your needs.
Selecting the correct Safety Protective clothing product for your particular circumstances can be difficult.The following information may be helpful:• A71andA80areourchemicalprotectivecoverallsmeetingEN14605:2005Type3.Toassistyoufurther,wehavelisted
our Chemical permeation results on pages 43 - 48. For up to date information please visit our website www.kcprofessional.com/uk/chemicalprotection
• A50,A45,A40&A20+areourEN13034:2005Type6&ENISO13982-1:2004Type5offering.• A50isaunique,treatedSMS(2)productofferinggoodlevelsofProtectionandComfortinasinglebase-sheet.• A40isafilmlaminateproductthatoffersmarketleadinglevelsofprotectionbutisnotasbreathableasA50.• A45isacombinationofA40&A50.A40provideshighlevelsofprotectiontothefrontwherethemajorityof
contamination will occur with A50 at the back providing breathability.• A20+isanSMSproductthatprovideshighlevelsofcomfortduetothebreathabilityoftheprotectivebase-sheet.
The selector is a guide only. It is the responsibility of the employer to make sure the protective clothing is suitable for its intended use. We suggest that you always check the latest version of KIMBERLY-CLARK PROFESSIONAL* product literature to get more information about the products or contact INFOFAX Service by emailing [email protected].
Product Test Method A20+ A25 A40 A45 A50 A71 A80
High Levels of Comfort
High comfort with superior freedom of movement
High Levels of Protection
Combination of A40 front for protection with A50 back for comfort
Combines reasonably high levels of Protection and Comfort
Chemical Protection
High level Chemical Protection
Type 3 EN 14605:2005 Pass Pass
Type 4 EN 14605:205 Pass
Type 5 EN ISO 13982-1:2004 Pass Pass Pass Pass Pass Pass Pass
Type 6 EN 13034:2005 Pass Pass Pass Pass Pass
Infective agents EN 14126:2003 Pass Pass
Surface Resistivity EN 1149-1:1995 Pass Pass Pass Pass Pass
Radioactive dust EN 1073-2:2002 Pass Pass Pass Pass Pass Pass
Fabric Tests
Abrasion resistance EN 530 Method 2 2 1 6 2 3 6 6
Flex cracking resistance ISO 7854 Method B 5 1 4 4 4 2 5
Trapezoidal tear resistance ISO-9073-4 2 1 2 2 2 2 3
Tensile strength EN ISO 13935-2 1 1 2 1 1 1 2
Seam strength EN ISO 13935-2 3 2 3 3 3 3 4
Puncture resistance EN 863 2 1 2 2 2 2 2
Resistance to ignition EN 13274.4 Method 3 Pass Pass Pass Pass Pass Pass Pass
EN 368
Repellency to liquids EN 368 (30% H2SO4) 3 3 3 3 3
EN 368 (10% NaOH) 3 3 3 3 3
Resistance to penetration by liquids EN 368 (30% H2SO4) 3 3 3 3 3
EN 368 (10% NaOH) 3 3 3 3 3
EN 374:3
Resistance to permeation EN 374:3 (30% H2SO4) 6 6
EN 374:3 (10% NaOH) 6 6
Whole Garment Tests (Tests performed with taping at wrists, ankles & hood)
Resistance to penetration by liquids in the form of a light spray (mist test)
EN 468 (modified) Pass Pass Pass Pass Pass Pass
Determination of resistance of suits to penetration by aerosols and fine particles
Pr ISO 13982-2 (Average total inward leakage)
4.41% 4.26% 5.09% 3.4% 4.34% 4.13% 3.6%
Chemical Guide
Pages 41-46
KLEENGUARD* Protective ClothingProduct selector
(1) For the latest information on Chemical protection, please visit our website: www.kcprofessional.com(2) Spunbond Meltblown Spunbond
For more information, please visit www.kcprofessional.com
6
KLEENGUARD* Protective ClothingOur Quality Shows In Every Format...
A BOUND SEAM is a serged seam that’s reinforced with binding for strength and tear resistance.
A TAPED SEAM is serged, then reinforced with a film tape that’s resistant to water and many liquid chemicals.
If your application requires a chemical resistant taped seam, you should ensure that the tape
offers appropriate resistance to the chemical involved.
A SERGED SEAM is a basic stitched seam that’s appropriate for exposure to non-hazardous substances. Overlap stitching provides strength and durability.
Zipper front, no elastic
Zipper front, elastic back, wrists & ankles
Zipper front, elastic back, wrists, ankles & hood
Zipper front, elastic back, wrists, ankles, hood & boots
And In Every Seam.
For more information, please visit www.kcprofessional.com
A20
A70
A80
A45
A40
A50
A10
A 71A 71
(4)
7
(3) As specified in European Standards documents EN 13034:2005 and EN ISO 13982-1:2004(2) Provides no protection against radioactive radiation
Suitable for handling of aqueous chemicals, low pressure industrial cleaning and maintenance.
Protection against aqueous chemical jet & spray(1)
• Durablefilmlaminatewithsewnandtapedseamsprovidesastrongbarriertochemicalspray(1)
• Sewnandtapedseamswithtearresistantfabricoffersastrongliquid-tightbarrier• Storm-flapheightandhooddesignedforeasiertapingtoarespirator• Elasticatedhood,cuffsandwaistdesignedforbettercomfortandsafety• Highlyvisibleforimprovedworkersafety• Siliconefreeandanti-staticfabricEN1149-1forcriticalareas• EN14126approvedforinfectiveagentsprotection• EN1073-2approvedforradioactivedustprotection(2)
• Keepawayfromflames
High performance protective clothing fabricOuter layer – film coating resists splash and spray from many liquids and dry particulates.
Inner layer – cloth-like, yet tough and abrasion-resistant spunbond polypropylene.
Description Size/Code M L XL XXL XXXL Colour Case Contents PPE Classification Type
A71 Coverall
96760 96770 96780 96790 9680010 ×
CAT III 3, 4 & 5
(1) Chemical test data can be found on our website, www.kcprofessional.co.uk/chemicalprotection
(Tests performed with taping at wrists, ankles and hood)
Product Performance Data
EN 14605:2005Type 4-B
Spray tight clothing
CE0120 EN 1149-1:1995Antistatic
EN 14605:2005Type 3-B
Liquid tight clothing
EN ISO 13982-1:2004Type 5-B
Particle protection
EN 1073-2:2002Radioactive dust
contamination protection
EN 14126:2003Infective agents
protection
Property
Fabric Tests
Whole Garment Tests
Test Method Class(3) or Result
Abrasion resistanceFlex cracking resistanceTrapezoidal tear resistancePuncture resistance Tensile strengthResistance to permeation
Seam strengthSurface resistivity– inside surfaceInfective agents
EN 530 Mth 2ISO 7854 Mth BISO 9073-4EN 863EN ISO 13934-1EN 374:3 (10% NaOH) EN 374:3 (30% H
2SO
4)
EN ISO 13935-2
EN 1149-1:1995EN 14126:2003 (A)
62221663
< 5 x 1010 ohmPASS
Resistance to penetration by liquids (Jet test)
Determination of resistance of suits to penetration by aerosols and fine particles
Radioactive dust
EN ISO 17491-4
pr ISO 13982-2
EN 1073-2:2002
PASS
Average Total Inward Leakage 4.13% avg
1
Chemical Guide
Pages 41-46
KLEENGUARD* Protective ClothingA71 Chemical Permeation and Liquid Jet Protection Clothing
(4) For the latest information on Chemical protection, please visit our website: www.kcprofessional.com
For more information, please visit www.kcprofessional.com
8
KLEENGUARD* Protective Clothing Jacket and TrousersA70 Chemical Spray Protection Apparel
For more information, please visit www.kcprofessional.com
Features•1.5milpolyethylenefilmcoatedspunbond
polypropylene fabric•Softandquietfabric•Awick-awayliningforenhancedcomfort•PatentedREFLEX*Designis7-1/2times
less likely to rip out than ANSI minimums – provides 12% more chest room and 6% longer body length
•Tapedstormflap•Boundseams•Liquid-resistant,extra-longzipper•NFPA99CompliantAntistaticMaterial
KLEENGUARD* A70 Apparel Fabric Properties
Physical Properties Test Method Results
Tensile Strength (MD) ASTM D5034 33.8 lbs
(CD) 24.1 lbs
Trapezoidal Tear (MD) INDA IST 100.2 12.3 lbs
(CD) 6.7 lbs
Mullen Burst ISO 13938-1 27.9 psi
Flammability CPSC 1610 Class 1
Static Decay (< 0.5 secs) NFPA 99 Pass
Barrier Properties Test Method Results
Blood Penetration ASTM F1670 Pass
Bloodborne Pathogens ASTM F1671‡ Pass
‡ Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Bloodborne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System.
WARNING: Fabric passes penetration testing; however, the chemical is a known or suspected carcinogen or skin absorbed toxin.
KLEENGUARD* A70 Apparel Fabric Liquid Chemical Resistance Test
Chemicals Liquid Penetration Vapor Permeation ASTM F1001 ASTM F903 ASTM F739 Test Duration: 60 mins. Normalized Saturation Exposure Breakthrough (min.) Rate (µg/cm2/min)
Acetone Pass Immediate 7.9
Acetonitrile Pass Immediate 8.97
Carbon Disulfide Pass Immediate 76.3
Dichloromethane Pass Immediate 85.1
Diethylamine Pass Immediate High
n,n-Dimethylformamide Pass Immediate 2.54
Ethyl Acetate Pass Immediate 40.3
n-Hexane Pass Immediate High
Methanol Pass Immediate 1.71
Nitrobenzene Pass Immediate 97.4
Sodium Hydroxide (50%) Pass >480 Not detected
Sulfuric Acid (98%) Pass >480 Not detected
Tetrachloroethylene Pass Immediate High
Tetrahydrofuran Pass Immediate 32.8
Toluene Pass Immediate High
KLEENGUARD* A70 - Level B/C Coveralls - Bound Seams - Yellow
Zipper Front, Storm Flap, Elastic Wrists, Size Case Count Typical Uses Ankles & Hood
09812 M 12 09813 L 12
09814 XL 12
09815 XXL 12
09816 XXXL 12
09817 XXXXL 12
09818 XXXXXL 12
• Hazardous waste remediation
• Environmental cleanup
• Petrochemical/oil refining
• Acid/caustic handling
• Biohazard cleanup
• Tank cleaning
• Pharmaceutical manufacturing
A20
A70
A80
A45
A40
A50
A10
A 71
(3) (4)
9
Suitable for critical production environments such as pharmaceutical industries, manufacturing, utilities, electronics, agriculture and paint spraying.
Protection against chemical splash and particles• Filmlaminatetechnologyprovidesanoutstandingbarrieragainstawiderangeofchemicals• Particleprotection,holdsout>99%offibresgreaterthan1micron• Strongtriplestitchedseamshelpprotectagainsttearing• Hooddesignedforrespiratoruseandfreedomofmovement• Fulllengthzip,easesabilitytogetin/outofgarment• Ultralow-lintperformance,filmlaminateandinternalseamssignificantlyreducelevelsoflint• Anti-staticfabricEN1149-1forcriticalareas• Siliconefree,idealforpaint-spraying• EN1073-2approvedforradioactivedustprotection(1)
• Compressedpackagingprovidesauto-dispensingsystemandreducesstoragespace• Sealedpolybagsforlowcontaminationrisk
High performance clothing fabricOuter layer – film coating resists splash and spray from many liquids and dry particulates.
Inner layer – cloth-like, yet tough and abrasion-resistant spunbond polypropylene.(2) As specified in European Standards documents EN 13034:2005 and EN ISO 13982-1:2004
(1) Provides no protection against radioactive radiation
(Tests performed with taping at wrists, ankles and hood)
Product Performance Data
Description Size/Code S M L XL XXL XXXL Colour Case Contents PPE Classification Type
A40 Coverall
99790 99791 99792 99793 99794 9979525 ×
CAT III 5 & 6
EN 1073-2:2002Radioactive dust
contamination protection
EN 13034:2005Type 6
Limited splash protection
CE0120 EN 1149-1:1995Antistatic
EN ISO 13982-1:2004Type 5
Particle protection
Property
Fabric Tests Test Method Class(2) or Result
Abrasion resistanceFlex cracking resistanceTrapezoidal tear resistancePuncture resistance Tensile strengthRepellence to liquids Resistance to penetrationResistance to ignition Seam strengthSurface resistivity
EN 530 Mth 2ISO 7854 Mth BISO 9073-4EN 863EN ISO 13934-1EN 368 (10% NaOH)/(30% H2SO4)EN 368 (10% NaOH)/(30% H2SO4)EN 13274-4 Mth 3EN ISO 13935-2EN 1149-1
642223 / 33 / 3PASS3< 5 x 1010 ohm
Whole Garment Tests
Resistance to penetration by liquids in the form of a light spray (mist test)
Determination of resistance of suits to penetration by aerosols and fine particles
Radioactive dust
EN 468 (modified)
pr ISO 13982-2
EN 1073-2:2002
PASS
Average TotalInward Leakage 5.09% avg
1
(3) For the latest information on Chemical protection, please visit our website: www.kcprofessional.com(4) Accessories available, please see page 14.
Chemical Guide Accessories
Pages 41-46 Page 14
KLEENGUARD* Protective ClothingA40 Liquid and Particle Protection Clothing
For more information, please visit www.kcprofessional.com
10
KLEENGUARD* Protective ClothingA30 Breathable Splash and Particle Protection stretch Apparel
KLEENGUARD* A30 Apparel Fabric Properties
Physical Properties Test Method Results
Tensile Strength (MD) ASTM D5034 29.7 lbs
(CD) 20.8 lbs
Trapezoidal Tear (MD) INDA IST 100.2 9.9 lbs
(CD) 6.9 lbs
Elongation (MD) ASTM D5034 41%
(CD) 53%
Mullen Burst ISO 13938-1 42.5 psi
Static Decay (5.0
10090
80
70
60
50
40
30
20
10
0
Per
cen
t (%
)
Particle Size (µm)
KLEENGUARD* A30
Leading market apparel
KLEENGUARD* A30 Apparel Fabric
• Pharmaceutical research
• Fine dry particle contamination
• Aerospace
• Maintenance/General manufacturing
Middle Layers – Intricate web of microfibers that filter out many
water-based liquids and dry particulates
KLEENGUARD* Apparel MICROFORCE* Barrier SMS Fabric
Outer Layers – Cloth-like, yet tough and abrasion-resistant spunbond
polypropylene
Zipper Front With 1” Flap, Size Case Count Typical Uses Elastic Back & Front, Wrists, Ankles & Hood
96141 M 25 96142 L 25
96143 XL 25
96144 XXL 25
96145 XXXL 21
96146 XXXXL 21
KLEENGUARD* A30 Coveralls
For more information, please visit www.kcprofessional.com
11
KLEENGUARD* Protective ClothingA20+ Breathable Particle Protection Clothing
KLEENGUARD* A20+ Product DescriptionIntended UseKLEENGUARD* A20+ Protective garments
• Limited life protective clothing designed to protect the user against liquid aerosols, spray and light splashing where the risk of chemical exposure is defined as low risk.
• Approved as Complex Design (category 3) equipment offering protection to the levels specified for Type 6 (performance requirements for chemical protective suits offering limited protective performance against liquid chemicals)J and Type 5 (particulates) by CEN.
Product DescriptionKimberly-Clark has invested in garment design and in the development of materials specifically for protective clothing to be able to offer the user the ideal combination of protection with comfort. Wearing garments of high breathability can reduce the effects of heat stress and therefore maintaining the efficiency and effectiveness of the wearer.
The fabricKLEENGUARD* A20+ Garments are made from an engineered structure called SMS which was invented by Kimberly-Ciark and initially used to offer medical staff protection with comfort in critical conditions.The fabric has been developed to suit it for the challenges of industrial applications. The 3 layers of the fabric are made up of polyolefin fibres, which are carefully engineered to deliver a combination of strength, durability and protection. The outer layers use large strong fibres to resist wear and tear and protect the central core layer. The centre of the structure is made up of closely packed fine fibres, which act as a highly efficient filter to particles, and as a barrier to many liquids.
The seamsTo provide high strength seams with barrier properties serged seams are used with triple overlock stitching.
The ZipTop quality full-length zips are used with stoppers to prevent strain.
Silicone FreeAll components are carefully selected and specified as silicone free — an important reassurance for anyone working with paint or sensitive surfaces.
Symbols and Marking on the garment — what they tel! you
ENl149-1 Antistatic Clothing (Electrostatic dissipative protective clothing to avoid incendiary discharges)
This symbol demonstrates that the garment is suitable for protection against chemicals. The CE mark followed by 0120 indicates that this is equipment of Complex Design (cat 3}, and that the product is manufactured under a quality system, which has been approved by, notified body 0120 (SGS Weston-Super - Mare).
Type 5 — Limited use clothing offering particle protection.
Type 6 - Limited splash clothing.
The open book pictogram ~ indicates that the user should read and understand the USER INSTRUCTIONS before using the garment.
Inflammable. Keep away from open flames, sparks or intense heat sources. The fabric will begin to melt atapprox. 120°C
CE0120
For more information, please visit www.kcprofessional.com
12
KLEENGUARD* Protective ClothingA20+ Breathable Particle Protection Clothing
For more information, please visit www.kcprofessional.com
Symbols and Marking on the garment - what they tell you
Do not wash
Do not tumble dry
Do not use chlorine — based bleach
Do not iron
Do not dry clean
Product Performance DataTo be certified as a Type 5 and Type 6 chemical protective garment, KLEENGUARD* A20+ must meet certain performancerequirements laid down by CEN, the European committee for normalisation. The standards apply throughout all member states of the EU.
For each property test data is classified into bands indicted bya CLASS number on a scale where 1 is lowest. There are a different number of classes for different tests. For some tests a simple pass /fail result is given.
The product performance data for KLEENGUARD* A20+ Coveralls is shown below.
Limited Use Chemical Protective Clothing (Type 5&6)
Property Test Method Class/Result
Abrasion Resistance EN 530 M2 Class 2 of 6
Stability to Heat ISO 5978 Class 2 No Blocking
Flex Cracking Resistance ISO 7854 M B Class 5 of 6 Visual
Trapezoidal Tear Resistance ISO 9073-4 Class 1 / 2* of 6
Puncture Resistance EN 863 Class 2 of 6
Repellence to Liquids
EN ISO 6530 10%NaOH Class 3
30%N2SO4 Class 3
Repellence to Penetration by Liquid EN ISO 6530
10%NaOH Class 3Chemicals 30%N2SO4 Class 3
Eesistance to Ignition EN 1146 PASS
Seam Strength ENISO 13935 - 2 Class 3
Repellence to Penetration by Liquid EN ISO 17941 - 4 PASS(spray test) (modified)
Determination of resistance of suitsto penetration by aerosols and fine EN ISO 13982-2 Average 10.9%particles
Surface Resistivity EN1149-5 : 2008 PASS
Type 6 EN 13034: 2005TYPE 5 to EN ISO 13982-1: 2004
13
KLEENGUARD* Protective ClothingA20+ Breathable Particle Protection Clothing
For more information, please visit www.kcprofessional.com
A20
A70
A80
A45
A40
A50
A10
A 71
(3)
PASS
Average TotalInward Leakage 4.41% avg
1
EN 468 (modified)
pr ISO 13982-2
EN 1073-2:2002
Resistance to penetration by liquids in the form of a light spray (mist test)
Determination of resistance of suits to penetration by aerosols and fine particles
Radioactive dust
Whole Garment Tests
132113 / 33 / 3PASS2
EN 530 Mth 2ISO 7854 Mth BISO 9073-4EN 863EN ISO 13934-1EN 368 (10% NaOH)/(30% H2SO4)EN 368 (10% NaOH)/(30% H2SO4)EN 13274-4 Mth 3EN ISO 13935-2
Abrasion resistanceFlex cracking resistanceTrapezoidal tear resistancePuncture resistance Tensile strengthRepellence to liquids Resistance to penetration by liquids Resistance to ignition Seam strength
Class(2) or ResultTest MethodFabric Tests
Property
Product Performance Data
(Tests performed with taping at wrists, ankles and hood)
(1) Provides no protection against radioactive radiation(2) As specified in European Standards documents EN 13034:2005 and EN ISO 13982-1:2004
Suitable for handling powders, general maintenance, construction and contract cleaning.
Protection against particles, fibres and chemical splash• DurableSMSfabrickeepsout99%ofparticleslargerthan1micron(I.O.MAloxitetest)• Triplestitchedinternalseamsprotectagainsttearing• Breathablefabricreducestheriskofheatstress• Speciallydesignedbody,hoodandwaistforcomfortandsafety• Siliconefreeforcriticalareas• Availableinwhite• EN1073-2approvedforradioactivedustprotection(1)
High performance SMS fabricOuter layers – cloth-like, yet strong and abrasion-resistant spunbond polypropylene.
Middle layer – intricate web of microfibres that filters out many water-based liquids and dry particulates.
Description Size/Code S M L XL XXL Colour Case Contents PPE Classification Type
A20+ Coverall
95150 95160 95170 95180 9519025 ×
CAT III 5 & 6
EN 1073-2:2002Radioactive dust
contamination protection
EN 13034:2005Type 6
Limited splash protection
CE0120 EN ISO 13982-1:2004Type 5
Particle protection
Accessories
Page 14
14
Overshoe with Sole• Asabovewithdurablesole
Mob Cap• Designedtokeephairinplaceandreducetheriskofcontamination
Apron / Sleeve / Overboot• ConstructedusingthesamematerialasourA40Anti-staticProtectiveclothing.• CATIproducts
Description Size/Code Colour Case Contents PPE Classification
A40 Accessory – Short Apron 44481 100 × CAT I
A40 Accessory – Sleeve 98730 200 × CAT I
A40 Accessory – Overshoe 98700 200 × CAT I
A40 Accessory – Overboot 98800 100 × CAT I
Description Size/Code Colour Case Contents PPE Classification
A10 Accessory – Mob Cap 82600 1000 × CAT I
Description M/L XL/XXL Colour Case Contents PPE Classification
A40 Accessory – Overshoe with Sole 98710 98720 200 × CAT I
A40 Accessory – Overboot with Sole 98810 98820 100 × CAT I
KLEENGUARD* Protective clothingA40 Accessories
A10 Accessories
For more information, please visit www.kcprofessional.com