Upload
wenigma
View
246
Download
0
Embed Size (px)
Citation preview
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 1/39
SCC is the brittle cracking of a metal due to the result of combinedeffects from localized corrosion and a tensile stress.
Stress Corrosion Cracking
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 2/39
Stress Corrosion Cracking
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 3/39
Stress Corrosion Cracking
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 4/39
• Can be Intergranular (Al-Cu, Cu base alloys) transgranular (Mg alloy or18/8SS) or mixed mode of cracking.
• Residual stresses due to cold working, welding etc.,
• Compressive stress does not cause
• Threshold stress is required
• Most of areas unaffected
• Specific to certain environmentsBrass - SCC in solutions with ammonia.Steel - SCC in caustic (high pH), amine solutions.Stainless steels and aluminium alloys - SCC in solutions containing chlorides.Ti-alloys - SCC in nitric acid or methanol.
Characteristic
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 5/39
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 6/39
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 7/39
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 8/39
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 9/39
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 10/39
Control(Material + Environment+ Tensile Stress)
1. Lower stress level below the threshold value (annealing,thickening the section)2. Eliminate critical species3. Apply cathodic protection4. Add inhibitor (Phosphate in boilers)
Mechanism
Electrochemical theory
Fissures at weak points of oxide film favour anodicdissolution & initiation of SCCStress sorption theory
Adsorption of ions on metal weakens metal atom bond
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 11/39
Failure of wall of a hydrofluoricalkylisation plant due tohydrogen blistering
Formation of cavities in thesteel due to hydrogen blistering
Brittle mechanical failure caused by penetration and diffusion of atomic hydrogen
into the crystal structure of an alloy.
(e.g) boiler tubes, plating, crude oil pipe lines picklingSteels in oil and gas industry
Hydrogen Embrittlement
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 12/39
The corrosion reactions in presence of hydrogen sulphides –
Anodic reaction: Fe → Fe2+ + 2e –
Dissociation reaction:H2S→ H+ + HS-
HS-→ H+ + S-
Cathodic reaction :
2H+ + 2e – → 2H → 2H2 (gas)
Corrosion process
H+ + e – → H H2O + e –
→ H+ + OH –
• H-bearing environment (heat treatment, wielding or other manufacturingprocess)
• Decomposition of water vapour or steam on hot surfaces.
Source of Hydrogen
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 13/39
Hydrogen Induced Cracking (HIC) – The corrosion damage is in theform of blisters and / or internal cracks in absence of STRESS
Sulfide stress Cracking (SSC) – Presence of STRESS
Posions - Presence of S2- and As3+ delay the recombination of H atoms.
P, Sb, Se, Te and Cyanide are other poisons.
Fe (Surface) + H2S (gas)→ FeS (Surface) + 2H (solution)
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 14/39
• Weakening of the metallic bond strength by the dissolve H.
• Diffusion of atomic H into metal and forms molecular H2 in voids/defectsforms blisters. This build up high pressure causes rupture.
• Diffusion of atomic H into metal and reacts with alloying elements to
form brittle hydrides
Prevention of HE
• Modification of environments
• Use of materials resistant to HE (High strength materials with low inclusion/voids)
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 15/39
• Large smooth area and a small corroded area
• Specific to high strength materials
• Transgranular failure
• Endurance limit is decreased by corrosive agent
Brittle failure of an alloy caused by fluctuating stress in a corrosive environment.
(Different from SCC)
(e.g) Sucker rods & drilling rods in oil wells rail vehicle springs, motor shaft working incorrosive environment
Characteristics
Fatigue occurs when a material is subjected to repeated loading and unloading.
Corrosion Fatigue
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 16/39
• Deep pits are initially formed
• Cracks initiates & propagates across the metal
• The frquency of cyclic stress is important. Lower frequency leads togreater crack propagation per cycle.
• Lowering the general corrosion rate will delay or prevent CF.
• Addition of inhibitors
• Barrier coating (Coating Zn, Cr, Ni, Cu & nitride)
• Reduce cyclic stresses by shot peening
Prevention
Mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 17/39
Also known as Selective Leaching or Selective dissolution or Parting
Removal of one element from an alloy leaving an altered residual structure.
Dezincification:
Selective removal of Zn from Brass with its yellow colour and its colourchanges to red (copper colour)
Dealloying
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 18/39
Selective dissolution of iron from Grey cast iron (E.g. Water pipes buried in soil)
Graphitization
Graphite flakes are cathodic to iron, and corrosion is localized to iron which startsleaching (becomes a porous mass) and leaves a rich residue of graphite flakes.
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 19/39
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 20/39
Characteristics
• Loss of mechanical strength without change in shape
• It leaves a porous structure• White cast iron does not undergo since C is present as Fe3C but leavesbehind a network of graphite flakes
Mechanism
C is present as graphite formPotential difference exists between graphite and ironLocal cell promotes corrosion of iron.
Prevention
Coal – tar epoxy coating on metal to prevent graphitizationTackling at desgin stageCupro-nickel or addition of 1% Sn to 70-30 brass reduces.Addition of 2% Al to Brass also prevents
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 21/39
Loaded metal surfaces under relative motions in the presence of corrosiveenvironment. e.g) Ball bearing, electrical switch gear
• Discolour & deep pit formation
• Relative motion small as 10-8 cm
Mechanism
• Wear – Oxidation – Rupture causes metal removal and oxidation• Oxidation wear – oxide layer ruptured and oxide debris formed• Exposed metal is further oxidized
PreventionLubricate with low viscosityIncrease hardnessUse gaskets to absorb vibrationRoughen the surface
Fretting Corrosion
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 22/39
MechanismRepeated formation of bubbles act as hammer and remove metal.
PreventionMetal must be high Corr. Resistant.Coating with neopreneUse dense high strength tensile material.
• Corrosion caused by impact of air bubbles in a medium (e.g) Marinepropellers, boiler tubes
• Pitting type of appearance and surface roughening
Cavitation Damage
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 23/39
Erosion-Corrosion
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 24/39
Erosion-Corrosion
Corrosion
A
B
C
Laminar
flow
Cavitationerosion
Turbulentflow
Erosion
A = Erosion - corrosionB = Cavitation erosion – corrosion
C = Turbulent flow corrosion
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 25/39
0
y
xd
notional profile in the absence offriction at the pipe walls
laminar flow (parabolic profile)turbulent flow
Fully developed velocity profiles in a circular section pipe
Types of Flow
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 26/39
entry zone unstable flow turbulence
laminar flow
inlet
inlet
(a)
(b)
Types of Flow
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 27/39
v (∞)
laminar layer
intermediatelayer
turbulent layer
laminar sub - layer
y
x0x CRIT
Hydrodynamic (prandl) boundary layers near the surface of a flat plate formed by a uniform
fluid velocity such that turbulent flow can develop
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 28/39
entry length Fully developed laminar flow
boundary layers boundary layers merge andbecome fully developed
Development of a hydrodynamic boundary layer for solution flowing through a tube
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 29/39
0 1 2 3 4
C o r r o s i o n r a t e m m / y e a r
0.0
0.2
0.4
0.6
0.8
Tidal 7.6 m/s 30.5 m/s
0.05
0.5
0.75
5 m/s
Max. recommendedin-service velocity
Critical velocity is not well defined for NAB. In seawater service conditions a maximum
flow rate of 5 m/s is normally recommended
Influence of fluid velocity on NAB
corrosion performance
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 30/39
Corrosion rate vs Velocity
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 31/39
Protective oxide film on NAB
• prevents corrosion• approx. 800 nm• complex layers of CuO, Cu2O and
Al2O3
• Level of protective film damage isdependent on particle impact angle
• Mechanical removal and/or ruptureenables charge transfer at varyingrates
• ‘Recovery’ aspects then become
important (system dependent)
Protective film integrity
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 32/39
For a ductile material, the
erosion mechanisms are (1)+ (2) microcutting, (3) plasticdeformation depending onthe angle of impingement.
Ductile erosion mechanisms
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 33/39
Cracksystems
• Fracture toughness plays an important role.
• Can depend on direction (perpendicular/transverse to coating / substrateinterface).
e.g. oxides at splat boundaries
Brittle erosion mechanism
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 34/39
T = E + C + S
or
S = T - ( E + C )
whereT is material loss under erosion-corrosion
E is material loss by pure mechanical erosion processesC is solids free flow corrosionS is synergy, the difference between erosion-corrosion (T) and the summationof erosion (E) and corrosion (C).
Synergistic effects can be:
– Negative (equivalent to extra safety factor)
– Positive (additional safety factor required)
Synergy
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 35/39
Zero Resistance AmmeterMicrobial Induced CorrosionImmediately after immersion, a metal surface
undergoes a sequence of biological and
chemical changes that lead to the formation of abiofilm which is causative for corrosion .
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 36/39
• highly complex structures containingvoids, microbial clusters or layers.
• diffusion in biofilms is dependent onflow conditions and structure.
A biofilm isheterogeneous innature and thedistribution ofmicroorganisms is
not uniform:
Slime, extracellular polymeric substances(EPS) - enzymes, proteins, nutrients, trappedinorganic material – possible modification ofoxygen reduction mechanisms
Microbial Induced Corrosion
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 37/39
Sulphate Reducing Bacteria
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 38/39
Copper alloys are more resistant to biofouling than most metals due to the toxicity ofthe released copper-ions.
When coupled to other metals the release of copper-ions can be greatly reduced.
The ennoblement of passive metals, such as titanium and stainless steels is well-documented:
• This ennoblement has been related to the formation of aerobic biofilms, althoughthe mechanism governing the processes is still a subject of much debate.
• Biofilms on titanium have been reported to catalyse the cathodic reduction ofoxygen – thus increasing the overall cathodic efficiency.
Biofilms and galvanic corrosion
7/26/2019 korozyon çeşitleri hakkındaaa
http://slidepdf.com/reader/full/korozyon-cesitleri-hakkindaaa 39/39
References
• S.N.Banerjee, “An Introduction to Corrosion Science and Corrosion Inhibition”,
Oxonian Press P.Ltd., New Delhi, 1985.
• Zaki Ahmad, “Principles of Corrosion Engineering & Corrosion Control”, ButterworthHeinemann, 2006.
• M.G.Fontana & N.D. Greene, “Corrosion Engineering”, McGraw Hill, New York ,1978.
• L.L.Shrier “Corrosion”, Vol. I & II, Butterworth Heinemann, 1994.
• H.H.Uhlig and R.W.Revie, “Corrosion and Corrosion Control”, A Wiley – InterScience Publication John Wiley & Sons, New York, 3rd Edition, 1985
and etc.