Lanztech Farming Solutions

Postal Address:Phone: +55 53 3311-0031

Mobile: +55 53 9971-2718

Mobile: +55 53 9976-8974

Email: [email protected]

Website: www.lanztech.com.br

Av. Tupy Silveira, 1720Bagé/RS - Brazil 96400-110

2

PERMANENT FENCING

Typical Fence Examples:

Tools:Pg 7 & 8

INTRODUCTION

Gates:Pg 10

Kiwitech Gates are just as strong as the fence itself and can be driven over. Gates can be as wide as 15m.

Fence costings include everything except labour & wooden posts.

1250mm Arrow posts (12m spacing)

1250mm Plain and Footed posts (80%:20%) (17m spacing)

1250mm Plain and Footed posts (80%:20%) (12m spacing)

1400mm Arrow posts (10m spacing)

6

8

8

8

8

10

9

Creek / Cliff Fence:

Cattle Fence:

Sheep Fence:

Race / Pressure Fence:

3

TEMPORARY FENCING

Construction Tools:

TriplePac (Carried) PowerPac Triple9 min 4 min4 min

10 min 3 min5 minConstruction:Deconstruction:

DoublePac (Carried) PowerPac Double7 min 3 min3 min8 min 2.5 min4 min

Construction:Deconstruction:

DuplexPac (Carried) DuplexPac (Vehicle mounted)8 min 4 min9 min 5 min


200m max when duplexing(half polywire length on spool)

Note variety of anchoring options.

Fence Items:

SinglePac (Carried) PowerPac DoubleSinglePac (Vehicle mounted)5 min 2 min2.5 min

Orbital Fence Kit Winder with Handle8min 8 min5 min 6 min 6 min 2 min3.5 min


Kiwitech's temporary fencing system is designed for shifting speed, toughness and versatility.

The same fence items can be used across a dozen modes of construction.

INTRODUCTION

Plus approximate times for constructing and deconstructing a 300m polywire fence.(Times are adjusted for systems where max distance < 300m)

DoublePac (Vehicle mounted)

TriplePac (Vehicle mounted)

Stay Tread-inAnch

or T

read

-in

Release Hookon Anchor Tread-in

Release Hookon steel wireor

Polywire: Pg 9

6 x 0.2mm stainless for great resistance to burnout.Tight uniform twist for longevity.

Spools: Pg 9

Release Hook: Pg 9

Pedals and Clips: Pg 8 & 9

End Assemblies: Pg 11-14

Polycarbonate amazing toughness.

Make the polywire let go from 400m away.Clip on to steel wire or Anchor Tread-in.

Hold up to 450m polywire.

Pedal and clip height easily adjustable.Single Wedge Clip for strong locking.Double Wedge Clip for adjustability.Fibregalss is U.V. paint coated for long life.

End Assemblies use Pedals with very long pins.Anchor Tread-ins are great for pinning down 'springy' permanent electric fences.

Tough and wear resistant as made fromglass reinforced nylon.

1, 2 or 3 Polywires:

1 or 2 Polywires:

1 or 2 Polywires:

1 Polywire: Pg 11 & 12

Pg 11

Pg 13

Pg 14

End Assemblies Tread-ins

Spools

4

WATER TROUGHS AND FITTINGS

Tee:

Round 100L Portable Trough:

The ballcock is built into the body of the trough and is all but indestructible. This trough is the natural companion of the Hydrant Tee and like the Micro is commonly located under a fenceto be shared from both sides.

INTRODUCTION

The Round Portable Trough was designed specifically to cope with the rigours of intensive bull farming (and it does).

MicroTrough Fixed or Portable: The MicroTrough is designed with intensive grazing in mind and despite its very small size and cost it can water at least 50 adult cattle. MicroTroughs are not recommended for sheep.

The MicroTrough is very quick to install and very indestructible. The Micro is based on Tee components so you can easily upgrade from Hydrant Tees to Micros. Fixed Micros are normally installed under an electric fence and can be shared by mobs from each side.

Tee Body

25mm O.D. Polypipe

Valve

11/4”- 25mm Adaptor(Cone, Collet & O-ring) Transition Fitting Example

What makes the Tee truly special is a valve that fits inside the Tee that can be activated by pushing 25mm O.D. polypipeinto the fitting. This makes for a very fast, inexpensive and very high flow hydrant. The pressure tolerance, overall toughness and frost-resistance of the fitting are outstanding.

The Kiwitech Tee is a uniquely versatile speed-coupling for polypipe. The core of the fitting is a threaded Tee Body with 11/4" BSP threads and a 30mm bore. A very wide variety of third party female adaptors can be threaded on to the legs of the Tee Body to create a transition fitting and the wide bore copes with flows typical of 40mm O.D. poly. The native Kiwitech Adaptor is designed for 25mm O.D. poly and ithas a push-lock, bayonet-release design (no tools, no threading).

Pg 17

Pg 16

Pg 16

11/4”- 40mm Plasson

Female Adaptor11/4”- 32mm

Plassim Female Adaptor

Fixed, buried Micro

Portable Micro(staked into ground)

5

Techno Basics:The imperatives for livestock farming are clear: higher productivity; lower energy and chemical inputs; better environmental and animal welfare practices, and lower labour input. Nothing matches TechnoGrazing as a tool to meet those challenges.

Better pasture utilisationBetter composition and feed qualityBetter fertility redistributionLower animal stressLess pugging and tramplingImproved parasite managementReduction in pasture pestsImproved ability to smooth seasonal pasture production differencesImproved ability to manage high-producing tall species (herbs, Lucerne)Improved ability to target nutrition for specific stock classesEasier, more precise, more flexible and simpler grazing managementAutomatic leveraging of the benefits of all conventional improvements (irrigation, drainage, new pasture, fertiliser, animal genetics) via the aboveImproved ability to run paddock trials to pinpoint specific productivity drivers.

TechnoGrazing achieves its logistical efficiency by running long, narrow, precisely laid out paddocks that are designed to be managed as a set. The trick is to construct a layout of a number (preferably an even number) of long narrow permanent paddocks that can be divided up with straight temporary cross fences running across the whole set of lanes thereby generating identically-sized grazing blocks. The temporary polywire fences lay on top of the permanent lane fences saving on Tread-ins and because there is only one fence covering several lanes the time spent on its construction and dismantling is minimal. A complete shift from one break to a new one works out at 1 to 4 minutes per mob depending on terrain and the tools used.

What's so different about Techno?TechnoGrazing rests on some very simple ideas: dramatically scale down the size of subdivisions and mob size (paddocks are measured in square metres rather than hectares); provide really efficient infrastructure; techniques and tools; add a dash of advanced grazing management, and benefit from a long list of productivity spin-offs:

INTRODUCTIONTECHNOGRAZINGTM

What makes Techno tick?

Kiwitech and its associates provide a comprehensive suite of services to help farmers get the most out of this uniquelyeffective concept. Hundreds of farmers from many different countries have used these training, design and consultancyservices alongside Kiwitech's hardware to achieve outstanding profitability. A lot of people are a bit distracted by someof Kiwitech's hardware and think that's all they need, but Kiwitech is focused on the Techno concept as its number one product because it is convinced that it adds far more to the customer's bottom line than any hardware could ever do. There are many misconceptions about TechnoGrazing, e.g. that it is only for bulls, that it is only suitable for small farms.In fact, there are several Techno sites of over 1000ha and the biggest one runs steers, not bulls.

Techno Services

1250 1500 1750 20001250 1500 1750 2000White

10mm x 1500mm

10mm x 1250mm

10mm x 1750mm

10mm x 2000mm

10mm x 1250mm

10mm x 1500mm

Green

1000White

10mm x 1500mm

10mm x 1750mm

10mm x 2000mm

10mm x 1250mm

10mm x 1250mm

10mm x 1500mm

Green

9mm x 1250mm

9mm x 1000mm

Bend

Plant

Pull

NB: 9mm posts are generally recommendedfor temporary (Tread-in) use only.

6

10mm x 1400mm

10mm x 1250mm

White1250 1400

Other lengths are available for large orders.

Footed posts must be driven deep then pulled back up to the correct height to trigger the barbs.

200 300 400

10mm x 300mm

10mm x 400mm

10mm x 200mm

White

*New Product:

Techno posts are stiffer, harder to break, will not sink and give terrific hold in the ground.Like the standard foot they must be planted deep, then pulled back. Because of their ferocious grip a Techno Rammer is usually needed for retraction.

The reinforced trunk and tapered sleevedramatically improve resistance to breakage.

FENCING: FIBREGLASS POSTS

Plain Posts 9mm & 10mm: Footed Posts 10mm:

Outriggers 10mm: Techno 'Arrow' Posts 10mm:

Anchoring fins should be in line with the fence.(as illustrated).

Techno Arrow: Stiffer, Tougher, More Gripping

FI P9-1000

FI P9-1250

FI P10-1250

FI P10-1500

FI P10-1750

FI P10-2000

FI PG10-1250

FI PG10-1500

FI FT10-1250

FI FT10-1500

FI FT10-1750

FI FT10-2000

FI FTG10-1250

FI FTG10-1500

FI OUT10-200

FI OUT10-300

FI OUT10-400

FI TA10-1250

FI TA10-1400

Hammer Cap (Nylon)

Hammer Pilot

Rammer Short

7

Techno Post Rammer(Standard)

Techno Post Rammer Pilot

Creating Pilot Holes

to pre-form a pilot hole. Extract the Pilot by

When the ground is very hard and/or rockyuse the Techno Rammer to drive the arrow Pilot

Arrow posts do a superb job in any situation but their specialfeatures shine through in: Heavy impact areas, e.g. races, holding yards Compression points, e.g. sharp crests Hollows, especially swampy or sandy soils Gentle corners, e.g. bluffs, water way fencing Centre Pivots, e.g. wheel crossing points, circular fences

A Hammer Cap can be used for:normal planting (if only a few posts are involved), for driving Outriggers andfor taking a Footed Post below Rammer depth to allow pull-back triggering of the barbs.

Techno Arrow Post Features

The Techno Post Rammer is good for virtually any type of fibreglass post (Plain, Footed or Arrow) up to 1500mm in length - variable sized spacers in the head adjust for different post lengths.

A Hammer Pilot is driven with a sledge hammer to pre-form a hole in very hard or rocky ground.

Triggering Techno Arrow Posts

the Arrow Post deep and retract it using the

Arrow Posts need to be triggered at plantingto get the best grip at the right height. Plant

built-in "extractor" to the correct height(secondary wings just below the surface).

hooking the chain to the Rammer so it can beused as a slide hammer.

FENCING: TOOLS

Post Planting Tools:

Rammer Long

(for post length 1500mm +)FT RAMLG

FT RAMSH

FT HAMPI

FT HAMCAPNY

FT TRAM

FT TRAMPI

This Rammer can be hired at a cost of $2.00 per day.

Wind Wire 'T' Clip x50 FA WINDCLPL

Applicators:

Wedge Body x50FA WBODL

Applicator: U-Clip

Applicator: Galvanised Wire Clip

Applicator: Wedge Clip Single

Applicator: Wedge Clip Double

Permanent fencing: 10mm

Body: 9mm or 10mm use

Temporary fencing: 9mm

(use with 9mm or 10mm Wedge)

8

a Single Wedge.

The machined step in a Single Wedge Applicatoris for the successful removal of a clip Body from

Place the step over the lugs ofthe clip Body and hit theapplicator with another object.

FENCING: TOOLS FENCING: ACCESSORIES

Clips:

Applicator: Single Wedge Step Function

Includes Body and Wedge




FT APU

FT APGAL

FT APWS

Stainless U-Clip x50FA UCLP10L

Galvanised Wire Clip x50FA GALCLP10L

Wedge Single 10mm x50FA WS10L

Wedge Double 10mm x50FA WD10L

FT APWD

Wedge Clip Single 9mm x50FA WCLPS9L

Wedge Single 9mm x50FA WS9L

Wedge Double 9mm x50FA WD9L

Wedge Clip Double 10mm x50FA WCLPD10L

Wedge Clip Single 10mm x50FA WCLPS10L

Wedge Clip Double 9mm x50FA WCLPD9L

The Hyperspring Inner allows the spring to extend to its naturallimit, and no further.Install after fence is constructed. Take care with knots.Use crimps on 2.5mm wire.

Pedal with Short Pin

Pedal with Long Pin

Pedal Bare

Pulley

Release Hook

Spool with 150m Polywire

Spool Bare



Polywire 400m


Polywire 600m

Handle Snap-in

1.25mm Hi-Tensile Wire 1000m

1.6mm Hi-Tensile Wire 1580m

9

Hyperspring Inner

Length: 575mm

Hyperspring Complete 2.5

Hyperspring Outer 2.5

Length: 495mm


Hyperspring Complete 1.6

Length: 430mm


Hyperspring Complete 1.25For 1.25mmHi-Tensile Wire

For 1.6mmHi-Tensile Wire

For 2.5mmHi-Tensile Wire

Length: 1290mm

FENCING: WIREFENCING: ACCESSORIES

Hi-Tensile Wire:

Spools, Polywire & Handle:

Hypersprings:

Tread-in / End Assembly Parts:

(used with all Hypersprings)Hyperspring Assembly

FA RELHK

FA PUL

FA PDBARE

FA PDSH

FA PDLG

FW SPLBARE

FW SPL150

FW SPL200

FW SPL300

FW SPL400

FW PWR400

FW PWR600

FP HDSNAP

FA SPRIN

FA SPROUT1.25

FA SPR1.25

FA SPROUT1.6

FA SPR1.6 FW HT1.25

FW HT1.6 FA SPROUT2.5

FA SPR2.5

Gate Heavy Duty Isolator

Gate Link

Race Hook

Open Gate Tension Keepers

Catchers / Isolators

Scabbard:Pole: FG IGPOL

StrainGate 1 Wire Set

StrainGate 2 Wire Set

Handle Strainer (Heavy Duty)

FENCING: GATES

StrainGate:

Gate Additions:

Integate:

(suitable for 'No 3' 145-175mm SEDwooden strainer posts)

Thong 180

(suitable for 'No 2 or 1' 175-200mm SEDwooden strainer posts)

Thong 240

Integate Application

insulating tube and a crimping sleeve).

Can tie on as many as 6 wires and hook onto eithera Thong or homemade thong (made from 2.5 fence wire,

Tension Device for permanent wire fences (storage drum holds approx 1-2m of spare wire)

Gate Handle Strainer Application:

Insulator (for light wire < 2.5mm)

Tape or Wire Gate

By taking at least 6 turns around the pole and using alazy twist knot a full-strength connection is made.The pole's shank acts as a drum for spare wire.

Conductor (max 2.5mm)

Thong 120

(suitable for 'No 4' 130mm SED wooden strainer posts)

10

SED (Small End Diameter)

FG HDSTRN

FG HDSTRN1

FG HDSTRN2

FG IGSCAB

Pole & Scabbard: FG IGEND

Integate 2 Wire Set: FG IG2Integate 3 Wire Set: FG IG3Integate 4 Wire Set: FG IG4

FG LNK

FG ISO

FG TH120

FG TH180

FG TH240

FG RCEHK

11

Pulley End Assembly

DuplexPac (Carried)FP PACCDX

Winder Duplex

DuplexPac (Vehicle Mounted)

+

x12

150m

(Chassis and Rack normally fitted for use)

(normally mounted on quad carrier)

DuplexPac Advantage:

Orbital Winding:

With a little co-ordination 150mof Polywire can be wound onto a Spool using the orbitalwinding technique (Spoolwith Snap-in Handle).

FENCING: 1 (400m) - 2 WIRE SHORT DISTANCE (200m) TEMPORARY

FENCING: 1 WIRE SHORT DISTANCE (150m) TEMPORARY

Orbital Fencing Kit:

Pulley End Assembly: Winder Options:

Single Wire: Orbital Fence Kit

The ability to put up one wire or two wire fences with a lighter Pac load (only one Spool required)Great for all-round use (sheep & cattle).

Maximum one wire fence length is 400m.Maximum two wire fence length is 200m.If a four wire fence is desired use an End Assembly with fourPulleys and wind Polywire ends round the cleats of a DoublePac.

Max length 150m.

(Single Wire: Tread-in 12 Kit (Double Wedge), Spool 150m, Snap-in Handle & Release Hook)

FKS DORFEKIT

FKD PULEND

FP WINDDX

FP PACVDX

12

FENCING: 1 WIRE TEMPORARY

QUANTITY PRICESINGLE DOUBLEWEDGE TYPE

FKS STRD12 FKS DTRD12

FKS STRDL FKS DTRDL

Single Wire: End Assembly

FKS STRD FKS DTRD100

12

50

FKS SCSTRTFKS DCSTRT

Single Wire: (Carried) Starter Kit

FKS SVSTRTFKS DVSTRT

Single Wire: (Vehicle Mounted) Starter Kit

x1 x1x6

x1 x1x18

+ x1

Spool 300m x1

Single Wire: End Assembly Kit

(Tread-ins with Single Wedge Clip)(Tread-ins with Double Wedge Clip)

Single Wire: Fence Kit

FKS SENDKITFKS DENDKIT

(SinglePac Carried + Single Wire Fence Kit)

(SinglePac Vehicle Mounted + Single Wire Fence Kit)

Winder: Single with HandleFP WINDSHD

SinglePac (Carried)FP PACCS

SinglePac (Vehicle Mounted)FP PACVS

Winder: SingleFP WINDS

PowerPac DoubleVP POWD

(information supplied on request)

FKS SFEKIT (Tread-ins with Single Wedge Clip)FKS DFEKIT (Tread-ins with Double Wedge Clip)





FENCING: 1 WIRE 'PRE-PACKED' KITS

Temporary Fencing Posts: Winder / Pac Options:

Fencing Kits: Starter Kits:

Single Wire: Tread-in

(use with Single Wedge Tread-ins only)

(End Kit, Tread-in 12 Kit, Spool 300m & Release Hook)

NOT BOXED

BOXED

(only sold in lots of 100)

FKS END

13

Temporary Fencing Posts:

Double Wire: End Assembly Kit


Double Wire: Fence Kit

FKD SFEKITFKD DFEKIT

FKD SENDKITFKD DENDKIT

Winder: DoubleFP WINDD

DoublePac (Carried)FP PACCD

DoublePac (Vehicle Mounted) FP PACVD

PowerPac DoubleVP POWD



x1 x1x4

Double Wire: Tread-in

x1 x1x24

+ x2

Spool 300m x2

Double Wire: End Assembly

FKD SVSTRTFKD DVSTRT

Double Wire: (Vehicle Mounted) Starter Kit

(DoublePac Vehicle Mounted + Double Wire Fence Kit)


FKD DCSTRTFKD SCSTRT

Double Wire: (Carried) Starter Kit

(DoublePac Carried + Double Wire Fence Kit)




FENCING: 1-2 WIRE TEMPORARY

FENCING: 1-2 WIRE 'PRE-PACKED' KITS

Winder / Pac Options:


The DoublePac can be used in Duplex mode (Pg 11) to make four wire fences. Use the cleats (on the Guide Outer) to secure free ends of Polywire.


(End Kit, 2x Tread-in10 Kit, 2x Spool 300m & 2x Release Hook)

Duplexing using the DoublePac


FKD STRD10 FKD DTRD10

FKD STRDL FKD DTRDL

FKD STRD FKD DTRD100

10

50

NOT BOXED

BOXED


FKD END


Temporary Fencing Posts: Winder / Pac Options:

Triple Wire: End Assembly

Triple Wire: End Assembly Kit

(Tread-ins with Single Wedge Clip)

Triple Wire: Fence Kit

FKT SENDKIT

Winder: Triple Wire FP WINDT

TriplePac (Carried)FP PACCT

TriplePac (Vehicle Mounted)FP PACVT

PowerPac TripleVP POWT



x1 x1x4 Triple Wire: (Carried) Starter Kit

FKT SVSTRT

Triple Wire: (Vehicle Mounted) Starter Kit

(TriplePac Carried + Triple Wire Fence Kit)

(TriplePac Vehicle Mounted + Triple Wire Fence Kit)



Triple Wire: Tread-in

x1 x1x24

+ x3

Spool 300m x3



(Single Wedge Clips recommended for 3 wires)

FENCING: 1-3 WIRE TEMPORARY

FENCING: 1-3 WIRE 'PRE-PACKED' KITS

14


(End Kit, 2x Tread-in10 Kit, 3x Spool 300m & 3x Release Hook)


FKT STRD10 N/A

FKT STRDL N/A

FKT STRD N/A100

10

50

NOT BOXED

BOXED


FKT END

FKT SCSTRT

FKT SFEKIT

Collet 9mm

Handle Green Bare

Strap (for Rack)

Rack Latch

Clamp, Upstand & Cradle

Clamp

Clamp & Upstand

Rack Bare

RackFP RK

Rack Mount Spare: Clamp

Chassis: Winder with Handle

Rack Mount Spare: Weld On

Chassis: Carried PacFP CHASC

Chassis: Vehicle PacFP CHASV

UpstandFP UP

Support CradleFP SUP

Rack

Chassis

Upstand & Clamp

Spare Rack Mounts

Gearbox Spanner

Gearbox Disc

Gearbox Bare

Gearbox Collet

Crank Handle

Chuck Triple

Chuck Double

Chuck Single

Guide Double (Inner)

Guide Elbow

Guide Double (Outer)

Guide DoubleFP GUD

Guide DuplexFP GUDX

Guide Single:FP GUS

Gearbox

Guides

Chucks

Guide Triple (Inner)

Guide Triple (Outer)

Guide TripleFP GUT

Guide Elbow

FENCING: PAC

Rack & Mounting Parts:Winder Parts:

(Gearbox, Spanner & Disk)

Gearbox Set

15

(used to support spools in transit)

FP GXSET

FP GXDSK

FP GXBARE

FP GXCOL9

FP CRNK

FP RKLCH

FP RKBARE

FP HDBARE

FP GXCOL9X

FP STRP

FP CHASHD

FP GUDIN

FP GUAELB

FP GUDOUT

FP GXDSKFP GXDSK

FP CLMPUP

FP CLMPUPSUP

FP GUTIN

FP GUAELB

FP GUTOUT

FP CLMP

FP RKMTSP

FP RKMTSPW

FP CHKS

FP CHKD

FP CHKT

(on errosion prone slopes the stake assists in keeping the troughhorizontal reducing the chance of spillage on the down slope)

16

Micro Portable Brick


R100 TubWT R100TUB

R100 L.D. PE Lead 8mWT R100LEAD


Tee Required: Trough (End of Line) 25mm (WF TTREND25)Valve Required: Valve 25mm (WV VAL25)

WATER: TROUGHS

(fitted with Standard Float & Trough Tee (End of Line) 25mmmaximum capacity 120L)

MicroTrough Portable:

Micro Portable TopWT MICGOTOP

Tee Required: Trough (End of Line) 25mm (WF TTREND25)Valve Required: Valve 25mm (WV VAL25)

Micro Portable Plate

Micro Portable Tub

Micro Pin

Micro Portable S.S Screw

Micro Portable Straight Stake

(Always use Low Density 25mm O.D.,20mm I.D. pipe for trough leads - less

chance of kinking)

R100 Standard Float

(for water pressure > 80 psi)

R100 Long Float

MicroTrough Buried:

MicroTrough (End of Line):

Micro Plate

Micro Tub

Micro Top (Tub, Plate & Pin)WT MICTOP

Micro Pin

MicroTrough:WT MIC

Trough (End of Line) 25mm (WF TTREND25)Valve Required: Valve 25mm (WV VAL25)

Tee Required: Trough 25mm (WF TTR25) or

Isolator Trough Tube 900mmWT ISO900

(Isolates wire above troughs, 'fix' with 4" nails)

H.P. Lead Release SleeveWT HPRELSLV

Trough Accessories:

High Pressure (H.P.) Lead Release SleeveDecoupling from a Hydrant can only be achieved by droppingwater presssure at the hydrant - usually achieved by emptyingthe round trough with its full-flow ballcock.

A High Pressure Release Sleeve pulls back,exposing holes drilled in the lead end. Water flows freely creating the required pressure drop.

When trough leads are very long and/or Hydrants are used in big diameter water lines (e.g. 32mm O.D.) and/orHydrants are in close proximity to the pump quick release will be difficult.

(pedestal used for smacking in stake)

MicroTrough for Hill Slope :

Micro Portable Ring Stake

(pedestal for smacking in stake)

MicroTrough Portable with Spike (for Softer Soils):

MicroTrough Portable:

NOT recommended for sheep

NOT recommended for sheep

(the spiked option is difficult to stake in very hard ground8m trough leads can be supplied on request)

WT R100

WT R100FL

WT R100LGFL

WT MICGO

WT MICGOSPIKE

WT MICGOPLT

WT MICGOTUB

WT MICPIN

WT MICGOSCW

WT MICGORNG

WT MICGOSTK

WT MICGOBRCK

WT MICEND

WT MICHILL

WT MICPLT

WT MICTUB

WT MICPIN

17

Tees: Tee Parts:

(Valve not included)

Trough 25mmWF TTR25

(Valve not included)

Body 25mmWF BOD25

Hydrant 25mm WF THY25

Hydrant (End of Line) 25mmWF THYEND25

Hydrant 25mm Less EndsWF THYMOD25

O-Ring 25mmWF ORNG25

Collet 25mmWF COL25

Cone 25mmWF CONE25

Cone Blank 25mmWF CONEBL25

Trough Tees (25mm O.D. pipe)

Hydrant Tees (25mm O.D. pipe)

Valve

WATER: FITTINGS

Trough (End of Line) 25mmWF TTREND25

(Cone, Collet & O-Ring)

Adaptor 11/4” - 25mmWF ADAPT25

BSP 11/4" thread compatible with a largerange of 3rd party fittings.Quotes for “Plassim” fittings given on request.

Cone PlugWF CONEPLG25If bad frosts are common, Cone Plugs shouldbe used with Cone Blanks in End of LineTrough and Hydrant Tees.

Stainless StentWF STENT25Low pressre spec polypipe, e.g. 8 bar rating or less, will require stents. Under high pressure,low spec pipe will collapse inside fittings resulting in water leakage. Stents, pushed inside polypipe ends, prevent pipe collapse.Stents are machined to order.

Fitting

Miscellaneous

Valve:

Keeper 25mmWV KEPR25

Plunger 25mmWV PLNG25

Body 25mmWV BOD25

Spring 25mm

If using with a Valve and screwing onto a 3rd party fitting, ensure the Valve’s plunger hasenough room inside the fitting to open fully.

From December 2007 the Body of Kiwitech’s valve wasstrengthened and the keeper design changed for easyremoval. If any part of the valve gets damaged it can now bereplaced.

Valve: Improvements

As per the illustration above, hold the valve in the palm of one hand and use the hand’s fingertips to pull back some of the spring from the Keeper. With the other hand push the keeper toward the spring simultaneously rotating it into the “thread” of the spring until the fins on the plunger align with the slots of the keeper - allowing the keeper to pop off.

Valve: Dismantling

. Valve: Assembly

Notches

Slots

Fin

Replace the plunger and fit the spring. One end of the spring is larger than the other end - the larger end MUST feed on first.Hold the valve as before (fingertips ready to pull back on thespring). With the other hand push the keeper onto the spring, past the plunger slots then ease the keeper back while turning into the thread of the spring. Ensure that the notches in the keeper snap onto the fins of the plunger.

WV VAL25

WV SPR25

VEHICLE: FENDER

Fender Kit: Fender Kit for PowerPac:

18

Antenna Blue Poly TubeVF ANTTUBE

Runner

Gripper WasherVF GRIPWSHZ

Gripper BoltVF GRIPBLTZ

Gripper UnitVF GRIPA

Crush BlockVF CRUSH

Front Facing FrameworkVF FRNTFCPT

Front Set

Front Backing PlateVF FRNTBACKPT

VEHICLE: POWERPAC FENDER

Make, Model and Year of quad required (custom fitted)

Make, Model and Year of quad required (custom fitted)

Support Bar

Support ClampVF SUPCLMP

Support Bar Plug

VF SUPBARPLG

Front Set for PowerPac

Antenna (with poly plug)

Rear PlateVF REARPT

Rear Set

Antenna Blue Poly Tube

Antenna (with poly plug)

Runner

Rear Set

Time Saving Fender KitKiwitech fences can be driven over! With a Fender Kit you can drive whereever you want - no more hopping on and off the quad to open gates. Fenders save a lot of time and they are very liberating.

Fender Kit OptionsIt is highly recommended that PowerPac users invest inthe Fender Kit with PowerPac support. The support bars take some of the PowerPac weight andload it onto the quad’s tough frame.

Front Facing Framework PPVF FRNTFCEPPPT

Requires PowerPac Carrier for attachment.

Fender Kit: VF KIT

VF ANT

VF FRNTSET

VF REARSET

VF RUN

Fender Kit for PowerPac: VF KITPP

VF ANTTUBE

VF ANT

VF REARSET

VF FRNTSETPP

VF SUPBAR

VF RUN

VEHICLE: OVER-FENDER

Fender Kit:

19

VEHICLE: EXOSKELETON

Over-Fender Kit:

Back Mount

Spider

Rudder

Feeler Blue Poly TubeVO FEELTUBE

Feeler

Antenna

MastVO MAST

Top

The Over-Fender lets you go over, under or through a fence.It is commonly used for K-line & sheep Techno.Make, Model and Year of quad required.

Accessory to Fenderopposite page

(Other options possible)

ExoSkeleton Kit:

Rail Right + Screws

Rail CoreVE CORE

Rail Casing Plastic

Rail Plug

Foot Plate + Bolts

Rail Left + Screws

Spring

Make, Model and Year of quad required.

Requires PowerPac Carrier for attachment.Can only manufacture for new quads as custom fitted.

(includes 12 stainless steel screws)

(includes 12 stainless steel screws)

(includes 2 x M8-25mm bolts + 4 x M6-25mm bolts)

Instep Plate

Rear Decking

(includes 16 tek screws)

$P.O.A(Some quads need an instep between theExo Rails and quad foot step running boards)

Over-Fender Kit: VO KIT

VO SP

VO RUD

VO FEEL

VO SPR

VO ANT

VO TOP

VO MT

ExoSkeleton Kit: VE KIT

VE CASE

VE PLG

VE FTPLT

VE RLRGPT

VE RLLFPT

VE REARDECK

StockRod Holster Top

Clamp Bottom

Projectile

StockRod Guide: Top

StockRod Guide: Middle

StockRod Guide: Bottom

Handle Bare Green

StockRod Reel Bare

Gearbox Disk

StockRod Reel+ 80m Polywire

StockRod Crank

StockRod Gearbox

StockRod Chassis

Collet 9mm

STOCK: HANDLING

StockRod: StockRod Holster:

20

StockRods are a very gentle and quiet way of handlinganimals in the paddock for: Drafting Forcing over fences Through gates or yards Handling dangerous or flighty animals

StockRod Practicality

Specially engineered for improved projectile casting.

SH RODPROJ

StockRod:SH ROD StockRod Holster:SH HOL

SH HOLTOP

FP CLMPBOT SH RODGUTOPM

SH RODGUMIDM

SH RODGUBOTM

FP GXCOL9X

FP HDBARE

SH RODCHAS

SH RODGX

SH RODCRNK

FP GXDSK

SH RODREELM

SH RODREEL80

Documents

Lanztech Farming Solutions