Embed Size (px)
Citation preview
*
*
*
*
*
*
Stud Finder Tape Measure Pencil Drill
1/2 in. (12.7 mm)
7/32 in. (5.5 mm)Wood Drill
Screw Driver Hammer
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.If you do not understand the instructions or have any concerns or questions, please contact a qualified installer. Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you require replacement parts, contact customer service at [email protected] product has been designed for use on a vertical wall constructed of wood studs. Wood studs being defined as a wall consisting of a minimum of 2” x 4”studs with a maximum of 16” stud spacing with a maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations please contact a qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of the total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure/surface will safely support the total load. This product may contain moving parts. Use with caution.DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
CAUTION! MAXIMUM WEIGHT CAPACITY
! 132 lbs(60kgs)
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN
INSTABILITY CAUSING POSSIBLE INJURY. USER MUST REMOVE TELEVISION OR OBJECT
OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT SURPASSES THE
TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV
SIZE!
WARNING!
Tools Needed (Not Included)
Socket Wrench
Weight Capacity
TV Bracket (Left and Right）
Arm Extensions 03 x2
04 x2
Front Support 02 x1
5/16 x 2½ inLag Bolts
x4A
WashersØ8mm
x4
B
x1
C
Philips ScrewsM8 x 15mmM8 x 45mm
Philips ScrewsM6 x 15mmM6 x 30mm
WashersØ6mm
M4-5-6
SpacersL10mm
x4x4 x4x4 x8 x4
M-A M-B M-C M-D M-E M-F
SpacersL5mm
x8
M-G
Arm andWall Plate 01 x1
Supplied Hardware
Socket Spanner
Step 1 Before TV Bracket Installation
75 mm ≈ 2 7/8 in 100 mm ≈ 4 in200 mm ≈ 7 7/8 in 300 mm ≈ 11 3/4 in400 mm ≈ 15 3/4 in 600 mm ≈ 23 5/8 in40
0mm
(15
3/4
in)
Max 600mm（23 5/8 in）
Max
Measure the distance between the holes located at the back of your TV (these measures may form the shape of a square, or a rectangle) and check that these taken measures are within the VESA(*) range for this wall mount.(*) VESA: International standard established by the TV manufacturers used to determine if LCD / LED TVs are compatible with wall mounts.
Check TV Screws
Please select the proper screw length for your TV by hand tightening to check your plat panel thread depth.
TV
M-F
M-A
04
M-C
04
M-D
M-EM-G
04
M-B
M-F
M-EM-G
04
04
04
For Flat Screen TV
For Curved TV
Step 2 Install TV Bracket
or
or
Use a stud finder (not included) to locate wood studs. Mark the edge and center locations.
16in(406mm)
Step 3A
3-1
3-2
Use wall plate 01 to mark mounting location x4 locations.
Ensure marking at the center of the stud.
01
01
Drill 4 pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. Make sure the depth is not less than 2 3/4” (70mm).
7/32
in.
Ø5.
5 m
m
in. (70 mm)
Mount the wall plate using 4 sets of 5/16 lag bolts (a) and washers B with a 1/2 in. socket wrench (not included).
AB
3-4
3-3
1/2 in. (12.7 mm)socket wrench
01
2
BA
UP
01
Use socket spanner C to remove the pre-assembed nuts and screws S4 from the extensions 02 and save them to use.
Insert the extensions into the .03 02
4-2
4-1
4-3
Fasten the nuts and screws S4 x8.
4-4
S1 S2Hang 02 and 03 into 01 , and using Screw Driver secure with pre-assembled screws and washers .
02S4
Step 4 Install Arm Extensions then Fasten It
S2S1
S1S2
02
S4
02
03
S4
0202
03
01
S4
02
C
C
S4
02 03 01
Secure TV with brackets against the arm extensions and with the pre-assembled screws [S3] .
04
S3
03 02
Hang TV with brackets 04 onto the arm extensions 02
and 03 .
Step 5 Hang TV
Step 6 Secure TV
04
03
04
02
04
[S3]
Screw Lock driver
Remove the preassembled screws [S3] and save to use, then raise the safety locks.
[S3]
If needed, the TV can be leveled +/-3 degrees.
Loosen 2 screws [S1]S1 Level the TV
To adjust the tilt in both sides, loosen both tilt levers and move panel to desired position. Tighten both tilt levers to hold desired tilt.
Step 7 Tilt Adjustment
Step 8 Level Adjustment
Tighten 2 screws S1
TIGHTEN
TIGHTEN
C
！
！LOOSEN
C
4PCS
± 3°
Thank you for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? Should you have any issues, please don't hesitate to contact us. Telephone：800-5566-806 Mon-Fri 10am - 6pm (PST) (USA) Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
