Embed Size (px)
Citation preview
LAUNCHASSEMBLY INSTRUCTIONS
Launch by OFS | 2
Checked by ______________________________ Checked by ______________________________ Checked by ______________________________
LA-24358CT TABLE COMPONENTS LA-21658CT TABLE COMPONENTS LA-18956CT TABLE COMPONENTS
Top 3 Sections Top 3 Sections Top 3 Sections
Bases (ordered separately) 2 Bases (ordered separately) 2 Bases (ordered separately) 2
Beams 2 Sets of 2 Beams 2 Sets of 2 Beams 2 Sets of 2
J-channel 2 J-channel 2 J-channel 2
Beam Brace 3 Beam Brace 2 Beam Brace 2
HK-106 (3" Lag Bolt with washer) 1 HK-106 (3” Lag Bolt with washer) 1 HK-106 (3” Lag Bolt with washer) 1
HK-6 (4"x4" Clamp Plate & Screws) 4 HK-6 (4"x4" Clamp Plate & Screws) 4 HK-6 (4"x4" Clamp Plate & Screws) 4
HK-7 (3"x3/4" Clamp Plate & Screws) 4 HK-7 (3"x3/4" Clamp Plate & Screws) 4 HK-7 (3"x3/4" Clamp Plate & Screws) 4
HK-10 (2 1/2" L-Bracket & Screws) 8 HK-10 (2 1/2" L-Bracket & Screws) 6 HK-10 (2 1/2" L-Bracket & Screws) 6
HK-68 (#8x1" Flat Head Screws) 3 HK-68 (#8x1" Flat Head Screws) 2 HK-68 (#8x1" Flat Head Screws) 2
HK-58 (#10x7/8" Pan Head Screws) 3 HK-58 (#10x7/8" Pan Head Screws) 3 HK-58 (#10x7/8" Pan Head Screws) 3
LA-24358CT POWER/DATA COMPONENTS LA-21658CT POWER/DATA COMPONENTS LA-18956CT POWER/DATA COMPONENTS
First Box Power/Data (CT4) 1 First Box Power/Data (CT4) 1 First Box Power/Data (CT4) 1
Power/Data Box (CT4) 7 Power/Data Box (CT4) 6 Power/Data Box (CT4) 5
(non CT4) (8) (non CT4) (7) (non CT4) (6)
Handy Box with plug-in cord 1 Handy Box with plug-in cord 1 Handy Box with plug-in cord 1
T-connector power cables 8 T-connector power cables 7 T-connector power cables 6
Velcro Cord Managers 10 Velcro Cord Managers 10 Velcro Cord Managers 10
Wiring harness for lights (CT4) 2 Wiring harness for lights (CT4) 2 Wiring harness for lights (CT4) 2
Transformer (CT4) 2 Transformer (CT4) 2 Transformer (CT4) 2
Transformer Power Service (CT4) 1 Transformer Power Service (CT4) 1 Transformer Power Service (CT4) 1
Light Cover Lenses (CT4) 14 Light Cover Lenses (CT4) 12 Light Cover Lenses (CT4) 10
HK-37 (#10-x 3/4” Quad Pan DT) 8 HK-37 (#10-x 3/4” Quad Pan DT) 7 HK-37 (#10-x 3/4” Quad Pan DT) 6
Checked by ______________________________ Checked by ______________________________ Checked by ______________________________
LA-16254CT TABLE COMPONENTS LA-13552CT TABLE COMPONENTS LA-10850CT TABLE COMPONENTS
Top 3 Sections Top 3 Sections Top 3 Sections
Bases (ordered separately) 2 Bases (ordered separately) 2 Bases (ordered separately) 2
Beams 2 Sets of 2 Beams 2 Beams 2
J-channel 2 Beam Brace 1 HK-106 (3” Lag Bolt with washer) 1
Beam Brace 2 HK-106 (3” Lag Bolt with washer) 1 HK-10 (2 1/2” L-Bracket & Screws) 2
HK-106 (3” Lag Bolt with washer) 1 HK-6 (4"x4" Clamp Plate & Screws) 4
HK-6 (4"x4" Clamp Plate & Screws) 4 HK-7 (3"x3/4" Clamp Plate & Screws) 4
HK-7 (3"x3/4" Clamp Plate & Screws) 4 HK-10 (2 1/2" L-Bracket & Screws) 4
HK-10 (2 1/2" L-Bracket & Screws) 4 HK-68 (#8x1" Flat Head Screws) 1
HK-68 (#8x1" Flat Head Screws) 2
HK-58 (#10x7/8" Pan Head Screws) 3
LA-16254CT POWER/DATA COMPONENTS LA-13552CT POWER/DATA COMPONENTS LA-10850CT POWER/DATA COMPONENTS
First Box Power/Data (CT4) 1 First Box Power/Data (CT4) 1 First Box Power/Data (CT4) 1
Power/Data Box (CT4) 4 Power/Data Box (CT4) 3 Power/Data Box (CT4) 2
(non CT4) (5) (non CT4) (4) (non CT4) (3)
Handy Box with plug-in cord 1 Handy Box with plug-in cord 1 Handy Box with plug-in cord 1
T-connector power cables 5 T-connector power cables 4 T-connector power cables 3
Velcro Cord Managers 10 Velcro Cord Managers 10 Velcro Cord Managers 10
Wiring harness for lights (CT4) 2 Wiring harness for lights (CT4) 1 Wiring harness for lights (CT4) 1
Transformer (CT4) 2 Transformer (CT4) 1 Transformer (CT4) 1
Transformer Power Service (CT4) 1 Transformer Power Service (CT4) 1 Transformer Power Service (CT4) 1
Light Cover Lenses (CT4) 8 Light Cover Lenses (CT4) 6 Light Cover Lenses (CT4) 4
HK-37 (#10-x 3/4” Quad Pan DT) 5 HK-37 (#10-x 3/4” Quad Pan DT) 4 HK-37 (#10-x 3/4” Quad Pan DT) 3
Launch by OFS | 3
LAUNCH
Note: Illustrations display model LA-24358CT. Any variations in assembly for smaller models will be noted in the text.
INSTALLATION TIPS
1. Table will be too heavy to move after assembly. Be sure table base and beam assembly is in desired location and is level. See page 4, Step 2.
2. Table section with end opening labeled “A” must be over power source when powered through end of table. See page 5, Step 4.
3. First Box must always be installed at end of table. Match Box labeled “A” to opening labeled “A”. See page 12, Step 1.
4. When placing Power/Data boxes into table male end of T-connector must point towards First Box. See page 12, Step 1.
5. Power/Data boxes must be secured with brackets or warranty will be voided. See page 12, Step 2.
6. Center powered tables requires additonal splitter. See page 14.
Launch by OFS | 4
LAUNCH
STEP 1 - BEAM ASSEMBLY
Note: Skip this step if assembling models LA-10850CT or LA-13552CT.
1. Place beams veneer side down on soft surface (to prevent scratching).
2. Beams should be end to end, bored ends to the outside, with no gap between the beems.
3. Align grooves on the beams and slide the J-channel until it is centered on the two beams.
4. Screw J-channel to beams using twenty-four (24) pan head #10x7/8" screws (HK-58) on each J-channel.
STEP 2 - BASE PLACEMENT
1. Place bases in desired location. If assembling a table with Power/Data option, base should be placed over Power/Data outlets.
2. Place beams inside of opening so there is no gap between the beam and the mending plate on the base. The J-channel edge of the beam should be towards the floor.
3. Using a 3/16" drill bit, pre-drill holes for the lag bolts (HK-106) through the beam into the base.
4. Drive lag bolts through the beams into the base and tighten securely.
5. Level the base beam assembly at this time. Level should only be placed on mending plates while leveling since a “crown” is built into the beams.
Launch by OFS | 5
Note: Illustrations display model LA-24358CT. Any variations in assembly for smaller models will be noted in the text.
LAUNCH
STEP 3 - BRACE PLACEMENT
Note: Model LA-10850CT will not have any beam braces.
1. Place beam braces between beams so that they are spaced out evenly. DO NOT screw into place. Braces will be adjusted and fastened later.
STEP 4 - TOP PLACEMENT
Note: Model LA-10850CT is a one piece top.
1. Place top sections on base/beam assembly as shown.
2. If using Power/Data boxes, the table section with end opening labeled “A” must be over power source (Does not apply to Center Powered tables).
Launch by OFS | 6
LAUNCH
STEP 5 - BRACE ADJUSTMENT
1. Adjust location of all beam braces to rest inside of recessed pockets on underside of top.
STEP 6 - SECURE TOP SECTIONS
Note: Model LA-10850CT is a one piece top and does not use 4" x 4" clamp plates.
1. Pull top sections together leaving no gap between top sections.
2. Secure top sections together using four (4) 4" x 4" clamp plates (HK-6).
3. Use eight (8) #8 x 3/4" flat head screws (HK-6) on each clamp plate.
Launch by OFS | 7
Note: Illustrations display model LA-24358CT. Any variations in assembly for smaller models will be noted in the text.
LAUNCH
STEP 7 - TOP ADJUSTMENT
1. Adjust top location so there is an equal distance from each base to the edge of the top.
STEP 8 - TOP PLACEMENT
1. Attach top to base by using eight (8) #8 x 1 1/2" pan head screws (HK-15) on each base.
2. Attach top to braces by using eight (8) #8 x 1" flat head screws (HK-68) on each brace.
Equal Distances
#8 x 1” Flat Head
#8 x 1 1/2” Pan Head
Launch by OFS | 8
LAUNCH
STEP 9 - BRACE TO BEAM ATTACHMENT
Note: Model LA-10850CT and LA-13552CT do not have J-channels and do not require pre-drilling.
1. Where braces are located between J-channels, pre-drill with 1/8" drill bit through J-channel.
2. Attach brace to beam by using four (4) #8 x 1" flat head screws (HK-68) on each brace.
STEP 10 - L-BRACKET ATTACHMENT
1. Space out 2 1/2" L-brackets evenly between bases and beam braces.
2. Attach L-brackets by using four (4) #10 x 5/8" pan head screws (HK-10) on each L-bracket.
Pre-Drill Here
Launch by OFS | 9
Note: Illustrations display model LA-24358CT. Any variations in assembly for smaller models will be noted in the text.
LAUNCH
STEP 11 - TOP ADJUSTMENT
Note: Some model LA-10850CT’s are one piece tops and do not use 3" x 3/4" clamp plates.
1. To ensure top sections are flush to each other, use 3" x 3/4" clamp plate (HK-7) on each joint just outside of 4" x 4" clamp plates.
2. Attach clamp plates to top by using four (4) #8 x 5/8" pan head screws (HK-7) on each clamp plate.
Launch by OFS | 10
LAUNCH POWER PARTS
HANDY BOX
Plugs into floor outlet. Connected to first box by T-connector cable. Qualified electrician can remove plugs and directly hard wire unit.
FIRST BOX
For Center Powered table, see page 14. When the power source for the table is under the base, power from the Handy Box enters this box first. On the CT4 models, the First Box contains the light switch. On the CT4 models, the wiring harness for the lights always plugs into the First Box.
CT4 Model Shown T-Connector
Launch by OFS | 11
LAUNCH POWER PARTS
STANDARD POWER/DATA BOX
T-Connector cable plugs in one side, another cable plugs in the other side and goes to the next box.
T-CONNECTOR POWER CABLE (A)
Snaps between Power/Data boxes.
TABLE LIGHT POWER SOURCE (B)
Supplies power from First Box to Transformer(s).
TRANSFORMER (CT4 MODELS ONLY) (C)
Plugs into table light power source and supplies power to wiring harness(es).
WIRING HARNESS (CT4 MODELS ONLY) (D)
Plugs into Transformer and supplies power to all lights in table top.
-- For tables 108" to 189" --One transformer and one harness are required for setup.
-- For tables 216" to 243" --Two transformers and two harnesses are required for setup, one on each side of the table top.
A
C
B
D
Launch by OFS | 12Launch by OFS | 12
LAUNCH POWER ASSEMBLY
STEP 1 - POWER/DATA BOX PLACEMENT
1. Locate First Box labeled “A” and insert in top at end of table (opening “A”) over power source. If power source is in the center of the table, then the First Box must still be placed at the end of the table. T-connector MUST be positioned as shown in the illustration.
2. When placing additional boxes into table, male end of T-connectors MUST point towards First Box.
3. Place additional boxes into remaining openings, matching labels on boxes to labels on openings.
STEP 2 - SECURE POWER/DATA BOXES IMPORTANT: Brackets must be correctly installed or warranty will be voided due to possible damage to top or Power/Data Boxes.
1. Hold Power/Data Box bracket against side of Power/Data Box and insert machine screws (shipped with Power/Data box) through slot and into machined hole in sides of boxes. DO NOT tighten machine screws.
2. Slide bracket tight against underside of top and screw into place using 2 (or 4) #10 x 3/4" quad pan head screws (HK-37) per bracket.
3. Position box flush to worksurface and tighten machine screws.
STEP 3 - CONNECT HANDY BOX
For Center Powered table, see page 14.
1. Place Handy Box with plug-in cords inside of base.
2. Plug male end of T-connector power cable into Handy Box.
3. Plug female end of T-connector power cable into First Box.
Table Base Other Boxes
Launch by OFS | 13
LAUNCH POWER ASSEMBLY
STEP 4 - INSTALL WIRING HARNESS (CT4 MODEL ONLY)
1. Snake wiring harness between beams and through beam braces so single wire male connector end of harness is in proximity of the First Box.
2. Each pair of lights plugs into a pair of matching plugs on wiring harness(es). Connect lights to harness pushing plugs together to lock.
STEP 5 - (CT4 MODEL ONLY)
1. Plug table light power source into switch house of First Box.
2. Plug transformer(s) into table light power source.
3. Plug wiring harness(s) into transformer(s).
STEP 6 - CONNECT POWER/DATA BOXES
1. Plug male end of T-connector power cable into First Box.
2. Plug female end of T-connector power cable into adjacent box.
3. Continue for all Power/Data Boxes.
STEP 7
1. Plug Handy Box into floor outlet.
Launch by OFS | 14
LAUNCH POWER ASSEMBLY
FOR CENTER POWERED TABLES ONLY
1. Find the Splitter that is shipped with the Center Wire Management Column and attach to Power/Data Box closest to floor outlet.
2. Place Handy Box with plug-in cords inside of Center Wire Management Column.
3. Plug male end of T-connector power cable into Handy Box.
4. Plug female end of T-connector power cable into Splitter.
5. Plug in T-connector Power Cables from center of table out to ends of table.
01.17an OFS Brands™ company | 1204 East Sixth Street | Huntingburg, IN 47542 | 800-521-5381 | ofs.com
