LEAD ACID BATTERY CHARGER anson LEAD ACID BATTERY CHARGER ... · PDF fileLEAD ACID BATTERY CHARGER SBC ... This is a simple to use intelligent battery charger with the latest PWM

LEAD ACID BATTERY CHARGERSBC - 2110 / 2115 / 212012V 3-Stage IUoU Battery Charger with Power Supply Mode Selection

ansonMLEAD ACID BATTERY CHARGERSBC - 826824V 2.2A Smart Battery Chargerusing Micro Processor control unit with pulse width modulation charge technology

ansonM

◘ All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa.◘ SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE

Description Features

This series of 3 Stage chargers have 3 specific settings for Wet, Cal-Cal, AGM & GEL type battery to ensure fast, complete and safe charging of your battery as required by the manufacturers.

Soft Start Bulk Charge an pre-bulk charge for drained out battery.

The charger gives 50% of full constant current charge when it detects the battery is over depleted at less than 9V terminal voltage. When battery voltage rises to 11V the charger will resume the normal constant full current Bulk, constant voltage Absorption and Float charge stages.

In the Power Supply mode, the charger provides a constant voltage dc power to the external load connected to the battery and at the same time without over charging the battery. This is ideal for caravan and other battery backup applications. The Power Supply Mode output voltage is the selected Float Voltage.

The optional temperature sensor adjusts the charging voltages with the changes in ambient temperatures of the battery. This effectively prevents over and under charging the battery in hot summer days to cold wintry nights.

Only the 10Amp SBC-2110 model has convection cooling and one charging bank, others have thermal control fan cooling (zero to full speed) and dual charging banks.

The Over Voltage protection, in the case of component failure causing uncontrolled high voltage at the output, the charger will limit the voltage less than 17.5V to prevent damage to the battery and connected load.

• 3 Stage (IUoU) switching mode lead acid battery charger

• 3 Battery Type (Wet/ Cal-Cal/ AGM & GEL) selections

• 3 Float Voltage Settings (13.2/13.5/13.8V) selections

• Battery can be connected to charger permanently

• Power Supply/Charger Mode selectionThe power supply mode is ideal to charge battery with load and keeps battery fully charged

• Automatic Soft Start Bulk Charge to ensure a safe and gentle initial charging for deeply drained battery

• Temperature compensation with optional remote sensor to prevent over and under charging battery at high and low ambient battery ambient temperature.

• Dual LED indicators for Bulk, Absorption, Float charge stage ; Fault, Power/Charger Mode and Power On.

• Power On-Off Switch

• Silent fan cool operation -- The thermal control cooling fan with variable speed moves when ambient temperature of charger exceeds 40°C.

• Protections to the charger Short circuit, Over Load, Over temperature

• Reversed Polarity (thermal fused)

• Protection to the battery and load OVPThe charger will keep output voltage less than 17.5V to prevent damage to the battery and load.


Safety

Operation

Introduction

Specifications

Features

Weight

Dimension (WxHxD)

Bulk Charge Max. Current Level (Current Limit) for All Mode

Vbulk@ for Sealed Lead Acid Mode

Vbulk@ for Wet Mode

Vbulk@ for Calcium-Calcium Mode

Ripple & Noise (peak-peak)

Protection

Construction

Cooling System

Approvals

Optimal Efficiency

Max. Power

Full Load AC Current

AC Frequency Range

No Load AC Current

AC Input Voltage

Model

Approx. 400g

150x60x30 mm

2.2A

28.4V

28.8V

29.6V

200mV

Overload, Short Circuit, Over Temperature,Reverse Polarity, No Spark for battery connected,Short Output ans 40HR Max. Charging Time

Poly-Carbonate Casing, Water Resistant

Natural Convection

CE EN55014, 60335, 61000, 62233,IP55 for body only

≥80%

65W

1.3A@100VAC / 1A@230VAC

50 - 60Hz~

100mA@100VAC / 80mA@230VAC

100-240VAC

SBC - 8268

This is a simple to use intelligent battery charger with the latest PWM charging technology controlled by a powerful Micro-Processor Control Unit.It is suitable for all types of lead acid batteries from 8AH to 60AH.

•

•

•

••

•

•••

Microprocessor Control (MCU) 4 Stage Charging (Repair, Bulk, Absorption, Float) in Pulse Width Modulation PWM method.MCU monitors the battery condition from initial qualifying checks, repair, to absorption to float charges.No worries of over or under charging battery, charger can be connected permanently to battery.Auto pulse repair charge for deeply depleted battery.Suitable for all types of Wet, Gel, AGM lead acid battery from 8 to 60 AH.Thermal control regulates charging current in hot or enclosed conditions.Two swappable leads with clamps and eyelet terminal.Simple 3 selection key with intuitive iconic LED indicators.Universal AC input 100V to 240V

The charger only starts charging when it is connected to a battery. So there is no spark in contact with battery terminals.Reverse Polarity and Short Circuit protections are by electronics with flashing LED and charger will return to normal when the fault is cleared.A total time for Bulk and Absorption charge is limited to 40 hours to avoid over charging and waste of energy. Therefore it is not suitable for application of charging battery connected to external load connected. The charger is splash proof as its casing is sealed by ultra sonic.It is convection cooled and has thermal regulation to lower the charging current until the unit's temperature drops to an acceptable level. In the event of persistent rising temperature the charger will shut down its output at a preset maximum temperature.

The Smart Charger runs its own self-tests when connected to an AC source of (100 to 240V). There are 3 Charge Modes to be selected: Sealed Lead Acid / Wet / Calcium-Calcium charge.

The Smart Charger will scan the battery by injecting short DC pulses. If the battery is found faulty, the LED flashes until the faulty battery is disconnected.

When the battery is found to be chargeable, the battery will go through constant current Bulk Charge, then a Pulse Width Absorption Charge, and finally a Pulse Float Charge. The charger can be connected to battery permanently without over charge.

If the battery is found to be sulphated, the Smart Charger will use special repair charge pulses to de-sulphate the battery until battery becomes ready for normal bulk charge.If after 8 hours of repair charge, the battery still cannot be improved, it is then considered to be non- repairable and the LED will flash until battery is removed.

Checks faulty battery

3 Stage charging with Repair Charging

Repair charging

Accessories:A battery Charger with lead terminalsDetachable leads with crocodile clipsConnecting leads with ring teminals

LEAD ACID BATTERY CHARGERSBC - 816812V 5A Smart Battery Chargerusing Micro Processor control unit with pulse width modulation charge technology

ansonM LEAD ACID BATTERY CHARGERSBC - 2110 / 2115 / 212012V 3-Stage IUoU Battery Charger with Power Supply Mode Selection

ansonM


Safety

Operation

Introduction

Specifications

Weight

Dimension (WxHxD)

Bulk Charge Current Level (Current Limit) for Car / Low Temperature Mode

Bulk Charge Current Level (Current Limit) for Motor Mode

Vbulk@ for Car / Motor Mode

Vbulk@ for Low Temperature Mode

Vfloat High Level

Vfloat Low Level


Protection

Construction

Cooling System

Approvals

Efficiency

Max. Power

Full Load AC Current

AC Frequency Range

No Load AC Current

AC Input Voltage

Model

Approx. 400g

150x60x30 mm

1.5A

14.4V

14.7V

13.5V

12.5V

<200mV

Overload, Short Circuit, Over Temperature,Reverse Polarity, No Spark for battery connected

Poly-Carbonate Casing, Water Resistant

Natural Convection

CE EN55014, 60335, 61000, 62233,IP55 for body only

5A

≥78%

70W

1.5A@100VAC / 1A@230VAC

50 - 60Hz~

100mA@100VAC / 80mA@230VAC

100-240VAC

SBC - 8168

This is a simple to use intelligent battery charger with the latest PWM charging technology controlled by a powerful Micro-Processor Control Unit.It is suitable for all types of lead acid batteries from 5AH to 120AH.

•

•

•

••

••••

Microprocessor Control (MCU) 4 Stage Charging (Repair, Bulk, Absorption, Float) in Pulse Width Modulation PWM method.MCU monitors the battery condition from initial qualifying checks, repair, or bulk to absorption to float charges.No worries of over or under charging battery, charger can be connected permanently to battery.Auto pulse repair charge for deeply depleted battery.Suitable for all types of Wet, Gel, AGM lead acid battery from 5 to 120 AH.Thermal control regulates charging current in hot or enclosed conditionsTwo swappable leads with clamps and eyelet terminal.Simple 3 selection key with intuitive iconic LED indicators.Universal AC input 100V to 240V

The charger only starts charging when it is connected to a battery. So there is no spark in contact with battery terminals.Reverse Polarity and Short Circuit protections are by electronics with flashing LED and charger will return to normal when the fault is cleared.A total time for Bulk and Absorption charge is limited to 40 hours to avoid over charging and waste of energy. Therefore it is not suitable for application of charging battery connected to external load connected. The charger is splash proof as its casing is sealed by ultra sonic.It is convection cooled and has thermal regulation to lower the charging current until the unit's temperature drops to an acceptable level. In the event of persistent rising temperature the charger will shut down its output at a preset maximum temperature.

The Smart Charger runs its own self-tests when connected to an AC source of (100 to 240V). There are 3 Charge Modes to be selected: Motor Cycle / Car / Cold charge.The cold charge has higher voltage and can be used for either low temperature or calcium content battery.

The Smart Charger will scan the battery by injecting short DC pulses. If the battery is found faulty, the LED flashes until the faulty battery is disconnected.

When the battery is found to be chargeable, the battery will go through constant current Bulk Charge, then a Pulse Width Absorption Charge, and finally a Pulse Float Charge. The charger can be connected to battery permanently without over charge.

If the battery is found to be sulphated, the Smart Charger will use special repair charge pulses to de-sulphate the battery until battery becomes ready for normal bulk charge.If after 8 hours of repair charge, the battery still cannot be improved, it is then considered to be non- repairable and the LED will flash until battery is removed.

Checks faulty battery

3 Stage charging with Repair Charging

Repair charging

Features

Accessories:A battery Charger with lead terminalsDetachable leads with crocodile clipsConnecting leads with ring teminals


Specifications

Remarks

Recommended Battery Capacity Range

Included Accessories (cable, spare fuse)

Optional Accessories (Remote Temperature Sensor)

Weight

Dimension (WxHxD)

Anodized Aluminum Casing with Mounting Flange

Charge Cycle, Protection Indication

Approvals

Separate LED for Bulk, Absorption, Float and Fault Mode

Power ON / OFF LED Indicator

Power ON / OFF Switch

Temperature Sensor Socket

Thermostatically Controlled Variable Speed Fan (0 - full speed)

OVP (Output Over Voltage Protection)

Over Temperature Protection

Reverse Polarity Protection

Overload Protection

Short Circuit Protection

Efficiency at Maximum Power


Maximum Output Charging Current (continuous)

Selectable Charger / Power Supply Mode (13.2 / 13.5 / 13.8V)

Dual Bank (Outputs) Simultaneously Charging two Batteries(The two batteries must be of same chemistry, construction & type)

Battery Voltage to Trigger (cut-in) Soft Start Bulk Charge Mode

Soft Start Bulk Charge Current Level (current limit)

Soft Start Bulk Charge

Absorption Voltage for AGM/GEL Battery (14.0V to 14.2V)

Absorption Voltage for WET Battery (14.3V to 14.5V)

Absorption Voltage for Calcium-Calcium Battery (15.5V to 15.7V)

Float Voltage 1 (13.2V)



AC Input Current at Full Load at 230VAC

AC Input Voltage 180 - 260VAC, 50Hz~

Model

Output (Charge) Voltage Selections (2 battery type)

Protections

110VAC 60Hz~ (Input on request)

40AH to 100AH

Yes

Not Included Not Included Not Included

1.3 kg

160x61x173 mm

Yes

CE EN 60335 EN 55014

Yes Yes Yes

Yes Yes Yes

Yes Yes Yes

Yes Yes Yes

Convection Cool

Yes

Yes

Yes

Yes

Yes

≥90%

<100mV

10A

Yes

No

<9V

5A

Yes

Yes

Yes

Yes

Yes

Yes

1.2A

Yes

SBC - 2110

60AH to 150AH

Yes

1.4 kg

160x61x173 mm

Yes

Yes

Yes

Yes

Yes

Yes

Yes

≥87%

<100mV

15A

Yes

Yes

<9V

7.5A

Yes

Yes

Yes

Yes

Yes

Yes

1.8A

Yes

SBC - 2115

80AH to 200AH

Yes

1.6 kg

160x61x207 mm

Yes

Yes

Yes

Yes

Yes

Yes

Yes

≥82%

<150mV

20A

Yes

Yes

<9V

10A

Yes

Yes

Yes

Yes

Yes

Yes

3A

Yes

SBC - 2120

BATTERYSTATE OF

CHARGE

CHARGINGVOLTAGE

CHARGINGCURRENT

TIMEBULK CHARGE ABSORPTION CHARGE FLOATING CHARGE

3 - STAGE CHARGING DIAGRAM

S.O.C.

CONSTANT CURRENT CONSTANT VOLTAGE CONSTANT VOLTAGE

Documents

LEAD ACID BATTERY CHARGER anson LEAD ACID BATTERY CHARGER ... · PDF fileLEAD ACID BATTERY CHARGER SBC ... This is a simple to use intelligent battery charger with the latest PWM