Upload
jeff-mirondo-kibalya
View
226
Download
0
Embed Size (px)
Citation preview
8/11/2019 Lecture Set Three-Microwave Antennas
1/14
kyu microwave antennas ET422/2014
Microwave antennas
An antenna is a component that radiates and receives the RF or microwave power. It is a
reciprocal device, and the same antenna can serve as a receiving or transmitting device. Antennas
are structures that provide transitions between guided and free-space waves. Guided waves are
confined to the boundaries of a transmission line to transport signals from one point to another ,
while free-space waves radiate unbounded. A transmission line is designed to have very little
radiation loss, while the antenna is designed to have maximum radiation.
The antenna is a key component in any wireless system, as shown in below
The RF/microwave signal is transmitted to free space through the antenna. The signal propagates
in space, and a small portion is picked up by a receiving antenna. The signal will then be
amplified, down converted, and processed to recover the information.
Different categories of antennas
Wire antennas: These include dipoles, monopoles, loops, yagi yuda arrays etc. wire antennas
are characterized by low gains and used at lower frequencies .They have advantage of light
weight, low cost and simple design
Aperture antennas:
Include open ended waveguides, rectangular or circular horns, reflectors etc. Aperture antennas
are most commonly used at microwave frequencies and have moderate to high gains
Antenna arrays:
They consist of a regular arrangement of antenna elements with feed network. They aremotivated by two reason: Beam steering and beam nulling. Pattern characteristics such as beam
pointing angle and sidelobe levels can be controlled by adjusting the amplitude and phase
distribution of the array elements.
8/11/2019 Lecture Set Three-Microwave Antennas
2/14
kyu microwave antennas ET422/2014
Antenna characteristics and parameters
These parameters provide information about the properties and characteristics of an antenna
1. Radiation pattern
An antenna radiation pattern or antenna pattern is defined as a mathematical function or agraphical representation of the radiation properties of the antenna as a function of space
coordinates. In most cases, the radiation pattern is determined in the far field region and is
represented as a function of the directional coordinates. Radiation properties include power flux
density, radiation intensity, field strength, directivity etc.
For an antenna, the
a. Fieldpattern ( in linear scale) typically represents a plot of the magnitude of the electric or
magnetic field as a function of the angular space.
b. Powerpattern ( in linear scale) typically represents a plot of the square of the magnitude of
the electric or magnetic field as a function of the angular space.
c.
Power pattern ( in dB) represents the magnitude of the electric or magnetic field, in
decibels, as a function of the angular space.
8/11/2019 Lecture Set Three-Microwave Antennas
3/14
kyu microwave antennas ET422/2014
A major lobe (also called main beam) is defined as the radiation lobe containingthe direction of
maximum radiation
A minor lobe is any lobe except a major lobe
Aside lobe is a radiationlobe in any direction other than the intended lobe. (Usually
a side lobe is adjacent to the main lobe and occupies the hemisphere in the direction
of the main beam.)
8/11/2019 Lecture Set Three-Microwave Antennas
4/14
kyu microwave antennas ET422/2014
A back lobe is a radiationlobe whose axis makes an angle of approximately 180with respect
to the beam of an antenna. Usually it refers to a minor lobe that occupies the hemisphere in a
direction opposite to that of the major (main) lobe.
Minor lobes usually represent radiation in undesired directions, and they should be minimized.
Side lobes are normally the largest of the minor lobes.
The level of minor lobes is usually expressed as a ratio of the power density in the lobe in
question to that of the major lobe. This ratio is often termed the side lobe ratio or side lobe level
Isotropic,Directional And Omnidirectional Patterns
An isotropic radiator is defined as a hypothetical lossless antenna having equal radiation in all
directions. Although it is ideal and not physically realizable, it is often taken as a reference for
expressing the directive properties of actual antennas. A directional antenna is one having the
property of radiating or receiving electromagnetic waves more effectively in some directions
than in others
This type of a pattern is designated as omnidirectional, and it is defined as one having an
essentially nondirectional pattern in a given plane (in this case in azimuth) and a directional
pattern in any orthogonal plane (in this case in
elevation). An omnidirectionalpattern is then a special type of a directionalpattern
Field Regions
The space surrounding an antenna is usually subdivided into three regions: (a) reactive near-
field, (b) radiating near-field (Fresnel) and (c) far-field (Fraunhofer) regions as shown in Figure
below. Although no abrupt changes in the field configurations are noted as the boundaries are
crossed, there are distinct differences among them. The boundaries separating these regions are
not unique, although various criteria have been established and are commonly used to identifythe regions.
Reactive near-field region is defined as that portion of the near-field region immediately
surrounding the antenna wherein the reactive field predominates. For most antennas, the outer
boundary of this region is commonly taken to exist at a distance R < 3
0.62 /D from the
antenna surface, where is the wavelength andD is the largest dimension of the antenna. For a
very short dipole, or equivalent radiator, the outer boundary is commonly taken to exist at a
distance/2 from the antenna surface.
Radiating near-field (Fresnel) region is defined as that region of the field of an antenna
between the reactive near-field region and the far-field region wherein radiation fields
predominate and wherein the angular field distribution is dependent upon the distance from the
antenna. If the antenna has a maximum dimension that is not large compared to the wavelength,
this region may not exist.
Far-field (Fraunhofer) region is defined as that region of the field of an antenna where the
angular field distribution is essentially independent of the distance from the antenna. If the
8/11/2019 Lecture Set Three-Microwave Antennas
5/14
kyu microwave antennas ET422/2014
antenna has a maximum overall dimensionD, the far-field region is commonly taken to exist at
distances greater than 2D2/ from the antenna,being
the wavelength.
Far f ield propert ies
The EM field in far field satisfies the following properties:
1. The Electric and magnetic fields are orthogonal
2. The ratio of the E and H fields is a constant and equal to the intrinsic impedance of the
medium
Thus EH
3. The fields in far field region are plannar.
Radian and Steradian
The measure of a plane angle is a radian. One radian is defined as the plane angle with its vertex
at the center of a circle of radius r that is subtended by an arc whose length is r. Since the
circumference of a circle of radius r is C = 2r, there are 2 rad (2r/r) in a full circle.
The measure of a solid angle is asteradian. Onesteradian is defined as the solid angle with its
vertex at the center of a sphere of radius r that is subtended by a spherical surface area equal tothat of a square with each side of length r. Since the area of a sphere of radius r isA = 4r2,
there are 4 sr (4r2/r2) in a closed sphere.
Radiation power density
Electromagnetic waves are used to transport information through a wireless medium or a guiding
structure, from one point to the other. It is then natural to assume that power and energy are
8/11/2019 Lecture Set Three-Microwave Antennas
6/14
kyu microwave antennas ET422/2014
associated with electromagnetic fields. The quantity used to describe the power associated with
an electromagnetic wave is the instantaneous Poynting vector defined as
W=EXH
Where
W = instantaneous Poynting vector (W/m2)E= instantaneous electric-field intensity (V/m)
H= instantaneous magnetic-field intensity (A/m)
Since the Poynting vector is a power density, the total power crossing a closed surface can be
obtained by integrating the normal component of the Poynting vector over the entire surface. In
equation form,
The time average Poynting vector (average power density) can be written as
Based upon the definition of (2-8), the average power radiated by an antenna (radiated
power) can be written as
8/11/2019 Lecture Set Three-Microwave Antennas
7/14
kyu microwave antennas ET422/2014
Radiation Intensity
Radiation intensity in a given direction is defined as the power radiated from anantenna per
unit solid angle. The radiation intensity is a far-field parameter, and it can be obtained by
simply multiplying the radiation density by the square of thedistance.
In mathematical form it is expressed as
The total power is obtained by integrating the radiation intensity over the entire solid angle of 4.
Thus
Beam Width
The beam width of a pattern is defined as the angular separation between two identical points on
opposite side of the pattern maximum.
One of the most widely used beamwidths is theHalf-Power Beamwidth (HPBW )HPBW definition: In a plane containing the direction of the maximum of a beam, the angle
between the two directions in which the radiationIntensity is one-half value of the beam..
Another important beamwidth is the angular separation between the first nulls of the pattern, and
it is referred to as theFirst-Null Beamwidth (FNBW).
8/11/2019 Lecture Set Three-Microwave Antennas
8/14
8/11/2019 Lecture Set Three-Microwave Antennas
9/14
kyu microwave antennas ET422/2014
Antenna Efficiency
Resistive losses due to non perfect and dielectric materials exist in all antennas. Such losses
result into a difference between the power delivered to the input of the antenna and the power
radiated by that antenna
We define radiation efficiency of an antenna as the ratio of the desired output power to thesupplied input power
1rad in loss loss
rad
in in in
p p p p
p p P
The total antenna efficiency e0 is used to take into account losses at the input terminals and
within the structure of the transmission line antenna system. Such losses may be due,
1. Reflections because of the mismatch between the transmission line and the antenna
2.I2R losses (conduction and dielectric losses)
8/11/2019 Lecture Set Three-Microwave Antennas
10/14
kyu microwave antennas ET422/2014
Gain
Another useful measure describing the performance of an antenna is thegain. Although
the gain of the antenna is closely related to the directivity, it is a measure that takes into the
antenna efficiency as well as its directional capabilities
Gain of an antenna (in a given direction) is defined as the ratio of the intensity, in a given
direction, to the radiation intensity that would be obtained if the power accepted by the antenna
were radiated isotropically. The radiation intensity corresponding to the isotropically radiated
power is equal to the power accepted (input) by the antenna divided by 4. In equation form
this can be expressed as
Note that the total radiated power (Prad) is related to the total input power (Pin)by Prad=ecd Pin
where ecdis the antenna radiation efficiency.
Effective area/Aperture:
Effective area (aperture), in a given direction is defined as the ratio of the available power at
the terminals of a receiving antenna to the power flux density of a plane wave incident on theantenna from that direction, the wave being polarization matched to the antenna. If the direction
is not specified, the direction of maximum radiation intensity is implied.
In general, the maximum effective aperture (Ae) of receiving antenna is related to the gain of the
antenna as,
8/11/2019 Lecture Set Three-Microwave Antennas
11/14
kyu microwave antennas ET422/2014
2
4e rA G
Input Impedance
Input impedance is defined as the impedance presented by an antenna at its terminals or the
ratio of the voltage to current at a pair of terminals or the ratio of the appropriate components of
the electric to magnetic fields at a point.
The ratio of the voltage to current at these terminals, with no load attached, defines the
impedance of the antenna as A A AZ R jX
whereA
Z =Antenna impedance at input terminals
AR =Antenna resistance at input terminals
AX =Antenna reactance at input terminals
Microwave AntennasHorn Antenna
The horn antenna is a transition between a waveguide and free space. A rectangular waveguide
feed is used to connect to a rectangular waveguide horn, and a circular waveguide feed is for the
circular waveguide horn. The horn antenna is commonly used as a feed to a parabolic dish
antenna, a gain standard for antenna gain measurements, and as compact medium-gain antennas
for various systems. Its gain can be calculated to within 0.1 dB accuracy from its known
dimensions and is therefore used as a gain standard in antenna measurements.
For a rectangular pyramidal horn, shown in Fig. below, the dimensions of the horn for optimum
gain can be designed by setting
where A and B are dimensions of the horn and leand lhare the slant lengths of the horn
8/11/2019 Lecture Set Three-Microwave Antennas
12/14
kyu microwave antennas ET422/2014
Parabolic Dish Antenna
A parabolic dish is a high-gain antenna. It is the most commonly used reflector antenna for
point-to-point satellites and wireless links. A parabolic dish is basically a metal dish illuminated
by a source at its focal point. The spherical wave front illuminated by the source is converted
into a planar wavefront by the dishFor an illumination efficiency of 100%, the effective area equals the physical area
where D is the diameter of the dish.
Radiation from parabolic dish antenna
Microwave propagation
In free space, electromagnetic waves propagate in straight lines without attenuation or other
adverse effects. Free space however is just an idealization that is only approximated when
8/11/2019 Lecture Set Three-Microwave Antennas
13/14
kyu microwave antennas ET422/2014
microwave energy propagates through the atmosphere or in the presence of the earth. In practice,
the performance of the communication system may be adversely be affected by effects such as
reflection, refraction, attenuation or diffraction and scattering
Attenuation: caused by absorption of microwave energy by water vapor and molecular oxygen
Ground effects: the most obvious effect of the presence of the ground on microwave
propagation is reflection from the earths surface. A receiver may be illuminated by both a direct
wave from the transmitter and a wave reflected from the ground. The reflected wave is smaller in
amplitude than the direct wave because of the larger distance it travels, the fact that it usually
originates from the side lobe region of the transmit antenna.
Plasma Effects: Plasma is a gas consisting of ionized particles. The ionosphere consists of
ionized particles due to solar radiation. Depending on the density of ions and frequency, wave
may be reflected, aborbed or transmitted by the plasma medium.
Microwave Biological effects and safety
The proven dangers of exposure to microwave radiation are due to thermal effects .The body
absorbs RF and microwave energy and converts it to heat; as in the case of the microwave oven,
this heating occurs within the body and may not be felt at low levels. such heating is more
dangerous in the brain, the eye and stomach organs.
Excessive radiation can lead to cataracts, sterility and cancer.
This makes it important to determine the safe radiation levels so that users of microwave
equipment will not be exposed to harmful power levels.
The most recent standards for human exposure as given by IEEE:In the RF microwave frequency range of 100 MHz to 300 GHz, exposure limits are set on the
power density (w/cm2) as a function of frequency. The recommended safe power density limit is
as low as 0.2 mw/cm2
at the lower end of the frequency range since the fields penetrate the body
more deeply at lower frequencies. At frequencies above 15 GHz the power density limit rises to
10 mW/cm2, since most of the power absorption at such frequencies occurs near the skin surface.
Other countries have different exposure limits some of which are a function of exposure time.
A separate standard applies to microwave ovens in the United States; Law requires that all
microwave ovens be tested to ensure that the power level at 5cm from any point of the oven does
not exceed 1 mW/cm2.
Exercise
1. A parabolic reflector antenna used for reception with DBS system is 0.45m in diameter
and operates at 12.4 GHz. Find the operating wavelength and the far field distance for
this antenna.
2. Distinguish between reflection, refraction, scattering and diffraction
8/11/2019 Lecture Set Three-Microwave Antennas
14/14
kyu microwave antennas ET422/2014
3. A 6 GHz common carrier microwave communication link uses a tower mounted antenna
with a gain of 40dB and a transmitter of power 5W.Evaluate the radiation hazard of this
system at a distance of 20m from the antenna.
4. A microwave antenna is characterised by Electric field intensity
sinoE A
r
field.Calculate power radiated at apoint located in far field