LED - tridonic.com · • Luminous flux up to 18,550 lm at tp = 65 °C • High efficacy up to 142 lm/W for the LED module at tp = 25 °C ... 01 02 0403 05 0706 08 09 01 00 Tc [°C]

www.tridonic.com 1Subject to change without notice.

Data sheet 06/16-LED152-6

LED light engine / OLEDLED compact

Product description

• Luminous flux up to 18,550 lm at tp = 65 °C

• High efficacy up to 142 lm/W for the LED module at tp = 25 °C

• High system efficacy up to 115 lm/W at tp = 65 °C

• High colour consistency (MacAdams 3)

• Excellent thermal management by COB technology

• KTY 82/210 for temperature control, compatible with ECO and TOP

(up to 35 W) LED Driver

• Uniform radiation with Dam&Fill technology

• Fixing holes for M3 screws

• Built-in LED module

• Cooling required

• Flexible operating modes

• 5-year guarantee

ÈStandards, page 4

Colour temperatures and tolerances, page 7

Umodule STARK FLE GEN1umodule FLE

PHASED OUT




Technical dataBeam characteristic 115°

Ambient temperature range -25 ... +50 °C

tp rated 65 °C

tc1 up to 90 °C

Max. DC forward current for LES302 1,750 mA

Max. DC forward current for LES402 3,500 mA

Max. permissible LF current ripple for LES30 2,400 mA

Max. permissible LF current ripple for LES40 5,000 mA

Max. permissible peak current for LES30 4,800 mA / max. 10 µs

Max. permissible peak current for LES40 10,000 mA / max. 10 µs

Max. permissible output voltage of LED Driver for LES303 250 V

Max. permissible output voltage of LED Driver for LES403 250 V

Insulation test voltage for LES30 1.5 kV

Insulation test voltage for LES40 1.5 kV

ESD classification severity level 4

Risk group (EN 62471:2008) 1

Type of protection IP00

Umodule STARK FLE GEN1umodule FLE

tc/tp

0,010,75

32,00

44,5053,2564,00

tc/tp

0,010,75

32,00

44,5053,2564,00

0 3 4 24 44 48 0 3 4 24 44 48

LES 30

ø30 ø40

ø3,3 ø3,3

1,65

±0,

15

1–26,1

1,65

±0,

15

1–26,1

LES 40

KTY 82/210 KTY 82/210

Ordering dataType Article number Colour temperature Packaging Weight per pc.

STARK-FLE-G1-LES30-830-CLA 89601873 3,000 K 20 pc(s). 0.014 kg


STARK-FLE-G1-LES30-765-IND 89601875 6,500 K 20 pc(s). 0.014 kg



STARK-FLE-G1-LES40-765-IND 89601878 6,500 K 20 pc(s). 0.014 kg

PHASED OUT




Specific technical dataType7 Photo-

metric code

Forward current

Luminous flux at

tp = 25 °C4

Luminous flux at

tp = 65 °C4

Power consumption module4 6

Min. forward voltage at tp = 65 °C

Max. forward voltage at tp = 25 °C

Luminous efficacy module at tp = 25 °C

Luminous efficacy module at tp = 65 °C

Luminous efficacy system at tp = 65 °C5

Colour rendering index CRI

STARK-FLE-LES30 – Operating mode at 900 mASTARK-FLE-G1-LES30-830-CLA 830/349 900 mA 5,100 lm 4,500 lm 44.3 W 47.5 V 54.0 V 113 lm/W 102 lm/W 92 lm/W 80

STARK-FLE-G1-LES30-840-CLA 840/349 900 mA 5,850 lm 5,150 lm 44.3 W 47.5 V 54.0 V 129 lm/W 116 lm/W 104 lm/W 80

STARK-FLE-G1-LES30-765-IND 765/349 900 mA 6,400 lm 5,650 lm 44.3 W 47.5 V 54.0 V 141 lm/W 128 lm/W 115 lm/W 70

STARK-FLE-LES30 – Operating mode at 1,400 mASTARK-FLE-G1-LES30-830-CLA 830/349 1,400 mA 7,500 lm 6,600 lm 72.4 W 50.0 V 56.2 V 101 lm/W 91 lm/W 82 lm/W 80

STARK-FLE-G1-LES30-840-CLA 840/349 1,400 mA 8,500 lm 7,500 lm 72.4 W 50.0 V 56.2 V 115 lm/W 104 lm/W 94 lm/W 80

STARK-FLE-G1-LES30-765-IND 765/349 1,400 mA 9,350 lm 8,200 lm 72.4 W 50.0 V 56.2 V 127 lm/W 113 lm/W 102 lm/W 70












STARK-FLE-G1-LES40-765-IND 765/349 3,500 mA 21,100 lm 18,550 lm 174.7 W 48.3 V 54.2 V 118 lm/W 106 lm/W 95 lm/W 701 See Derating curves in data sheet section 2.3.

2 Max. DC forward current varies over the temperature of the LED module. See derating curves in data sheet section 2.3.

3 The detailed explanation, see data sheet section 3.1.

4 Tolerance range for optical and electrical data: ±10 %.

5 Assumed efficiency for the LED Driver is 0.9.

6 All values at tp = 65 °C.

7 HE ... high efficiency, NM ... nominal mode, HO ... high output.

PHASED OUT




1. Standards

EN 62031EN 62471EN 61547EN 55015IEC 62717

1.1 Photometric code

Key for photometric code, e. g. 830 / 349

1.2 Energy classification

Type Forward current Energy classification

FLE-G1-LES30-830-CLA900 mA A+

1,400 mA A+1,750 mA A

FLE-G1-LES30-840-CLA900 mA A+

1,400 mA A+1,750 mA A+

FLE-G1-LES30-765-IND900 mA A+

1,400 mA A+1,750 mA A+

FLE-G1-LES40-830-CLA1,750 mA A+2,600 mA A+3,500 mA A+

FLE-G1-LES40-840-CLA1,750 mA A+2,600 mA A+3,500 mA A+

FLE-G1-LES40-765-IND1,750 mA A+2,600 mA A+3,500 mA A+

2. Thermical details

2.1 tp point, ambient temperature and life-time

The temperature at tp reference point is crucial for the light output and life-time of a u product.

For umodule STARK FLE a tp temperature of 65 °C has to be complied in order to achieve an optimum between heat sink requirements, light output and life-time.

Compliance with the maximum permissible reference temperature at the tp point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application.

2.2 Storage and humidity

storage temperature -30 ... +80 °C

Operation only in non condensing environment.Humidity during processing of the module should be between 30 to 70 %.

2.3 Derating curves

0

200

400

600

800

1000

1200

1400

1600

1800

0 10 20 30 40 50 60 70 80 90 100Tc [°C]

If [m

A]

2000

Umodule STARK FLE-G1-LES30

Umodule STARK FLE G1-LES40

0

500

1000

1500

2000

2500

3000

3500

0 10 20 30 40 50 60 70 80 90 100Tc [°C]

If [m

A]

4000

1st digit 2nd + 3rd digit 4th digit 5th digit 6th digit

Code CRIColour temperature in

Kelvin x 100McAdam

initial

McAdam after 25% of the

life-time (max.6000h)

Luminous flux after 25% of the life-time (max.6000h)

Code Luminous flux7 70 – 79 7 ≥ 70 %8 80 – 89 8 ≥ 80 %9 ≥90 9 ≥ 90 %

PHASED OUT




2.4 Thermal design and heat sink

The rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule STARK FLE will be greatly reduced or the umodule STARK FLE may be destroyed.

NotesThe actual cooling can differ because of the material, the structural shape, outside influences and the installation situation. A thermal connection between umodule STARK FLE and heat sink with heat-conducting paste or heat con-ducting adhesive film is absolutely necessary.Additionally the umodule STARK FLE has to be fixed on the heat sink with M3 screws to optimise the thermal connection.Use of thermal interface material with thermal conductivity of l > 1 W/mK and layer thickness of interface material with max. 50 µm or a similar interface material where the quotient of layer thickness and thermal conductivity b < 50 µmmK/W.

Umodule STARK-FLE-G1-LES30 ta tp Operating current Rth, hs-a

25 °C 65 °C 900 mA 1.20 K/W30 °C 65 °C 900 mA 1.04 K/W40 °C 65 °C 900 mA 0.73 K/W50 °C 65 °C 900 mA 0.42 K/W25 °C 65 °C 1,400 mA 0.69 K/W30 °C 65 °C 1,400 mA 0.59 K/W40 °C 65 °C 1,400 mA 0.41 K/W50 °C 65 °C 1,400 mA 0.22 K/W25 °C 65 °C 1,750 mA 0.51 K/W30 °C 65 °C 1,750 mA 0.44 K/W40 °C 65 °C 1,750 mA 0.30 K/W50 °C 65 °C 1,750 mA 0.16 K/W

Umodule STARK-FLE-G1-LES40ta tp Operating current Rth, hs-a

25 °C 65 °C 1,750 mA 0.65 K/W30 °C 65 °C 1,750 mA 0.56 K/W40 °C 65 °C 1,750 mA 0.38 K/W50 °C 65 °C 1,750 mA 0.21 K/W25 °C 65 °C 2,600 mA 0.38 K/W30 °C 65 °C 2,600 mA 0.33 K/W40 °C 65 °C 2,600 mA 0.22 K/W50 °C 65 °C 2,600 mA 0.11 K/W25 °C 65 °C 3,500 mA 0.25 K/W30 °C 65 °C 3,500 mA 0.21 K/W40 °C 65 °C 3,500 mA 0.14 K/W50 °C 65 °C 3,500 mA 0.06 K/W

2.5 Heat sink values

3. Installation / wiring

3.1 Electrical supply/choice of LED Driver

umodule FLE from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a LED Driver which complies with the relevant standards. The use of u LED Drivers from Tridonic in combination with umodule FLE guarantees the necessary protection for safe and reliable operation.

If a LED Driver other than Tridonic uconverter is used, it must provide the fol-lowing protection:• Short-circuit protection• Overload protection• Overtemperature protection

umodule FLE must be supplied by a constant current LED Driver.Operation with a constant voltage LED Driver will lead to an irreversible damage of the module.Wrong polarity can damage the umodule FLE.

umodule FLE are basic isolated up to 250 V against ground and can be mounted directly on earthed metal parts of the luminaire. If the max. output voltage of the LED Driver (also against earth) is above 250 V, an additional isolation between LED module and heat sink is required (for example by isolated thermal pads) or by a suitable luminaire construction.At voltages > 60 V an additional protection against direct touch (test finger) to the light emitting side of the module has to be guaranteed. This is typically achieved by means of a non removable light distributor over the module.

3.2 Wiring

+ –

+ –KTY 82/210

The temperature monitoring is available with Tridonic LED Driver series TOP (up to 35 W) and ECO with the ITM feature in combination with the thermal sensor KTY 82/210.If the temperature monitoring function want to be used it has to be wired as shown below in the wiring diagram.

Udriver LC(A)I (TOP)ECO

SEC

PRI

220–240 V

LN

0/50/60 Hz

ITM 1ITM 2

I sel 1I sel 2

+ LED– LED

KTY82/210

DA/NDA/L

~~ +

–PHASED OUT




3.5 EOS/ESD safety guidelines

The device / module contains components that are sensitive to electro-static discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation prac-tice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: http://www.tridonic.com/esd-protection

Operating mode tp temperature L90 / F10 L90 / F50 L80 / F10 L80 / F50 L70 / F10 L70 / F50

HE65 °C 51,000 h 60,000 h 60,000 h 60,000 h 60,000 h 60,000 h75 °C 38,000 h 57,000 h 60,000 h 60,000 h 60,000 h 60,000 h85 °C 29,000 h 43,000 h 60,000 h 60,000 h 60,000 h 60,000 h

NM65 °C 40,000 h 60,000 h 60,000 h 60,000 h 60,000 h 60,000 h75 °C 30,000 h 44,000 h 60,000 h 60,000 h 60,000 h 60,000 h85 °C 22,000 h 33,000 h 47,000 h 60,000 h 60,000 h 60,000 h

HO65 °C 32,000 h 48,000 h 60,000 h 60,000 h 60,000 h 60,000 h75 °C 24,000 h 36,000 h 50,000 h 60,000 h 60,000 h 60,000 h85 °C 18,000 h 27,000 h 38,000 h 57,000 h 60,000 h 60,000 h

4.1 Life-time, lumen maintenance and failure rate

The light output of an LED Module decreases over the life-time, this is characterized with the L value. L70 means that the LED module will give 70 % of its initial luminous flux. This value is always related to the number of operation hours and therefore defines the life-time of an LED module.

As the L value is a statistical value and the lumen maintenace may vary over the delivered LED modules. The B value defines the amount of modules which are below the specific L value, e.g. L70B10 means 10 % of the LED modules are below 70 % of the inital luminous flux, respectivly 90 % will be above 70 % of the initial value. In addition the percentage of failed modules (fatal failure) is characterized by the C value.

The F value is the combination of the B and C value. That means for F degradation and complete failures are considered, e.g. L70F10 means 10 % of the LED modules may fail or be below 70 % of the initial luminous flux.

3.4 Mounting instruction

umodule STARK FLE from Tridonic which have to be installed on a heat sink have to be connected with heat-conducting paste or heat conducting adhesive film and fixed with M3 screws.

The fixing/cooling surface must be cleaned before installing the u modules to remove all dirt, dust and grease.

None of the components of the umodule STARK FLE (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses.

Max. torque for fixing: 0.5 Nm.

Chemical substance may harm the LED module. Chemical reactions could lead to colour shift, reduced luminous flux or a total failure of the module caused by corrosion of electrical connections.

Materials which are used in LED applications (e.g. sealings, adhesives) must not produce dissolver gas. They must not be condensation curing based, acetate curing based or contain sulfur, chlorine or phthalate.Avoid corrosive atmosphere during usage and storage.

4. Life-time

4.2 Lumen maintenance

Life-time declarations are informative and represent no warranty claim.

3.3 Wiring type and cross section

The wiring can be solid cable with a cross section of 0.2 to 0.75 mm². For the push-wire connection you have to strip the insulation (7–9 mm).

7 – 9 mm

wire preparation:0.2 – 0.75 mm²

Inserting stranded wires / removing wires by lightly pressing on the push button.

PHASED OUT




5. Photometric charcteristics

MacAdam ellipse: 3SDCM

0,3550

0,3600

0,3650

0,3700

0,3750

0,3800

0,3850

0,3900

0,3950

0,36

00

0,36

50

0,37

00

0,37

50

0,38

00

0,38

50

0,39

00

0,39

50

0,40

00

4,000 Kx0 y0

Centre 0.3804 0.3767

380 420 460 500 540 580 620 660 700 740 7800,00

0,05

0,10

0,20

0,25

0,15

wave length [nm]

norm

. int

ensi

ty [W

/nm

]


0,3850

0,3900

0,3950

0,4000

0,4050

0,4100

0,4150

0,4200

0,4250

0,42

00

0,42

50

0,43

00

0,43

50

0,44

00

0,44

50

0,45

00

0,45

50

0,46

00

3,000 Kx0 y0

Centre 0.4369 0.4041

380 420 460 500 540 580 620 660 700 740 7800

0,10

0,15

0,25

0,30

0,45

0,05

0,20

0,35

0,40

wave length [nm]

norm

. int

ensi

ty [W

/nm

]

5.1 Coordinates and tolerances according to CIE 1931

The specified colour coordinates are measured integral after a settling time of 200 ms. The current impuls depends on the module type.

The ambient temperature of the measurement is ta = 25 °C.The measurement tolerance of the colour coordinates are ± 0.01.

Module type Current impulseumodule STARK-FLE-G1-LES30 1,400 mAumodule STARK-FLE-G1-LES40 2,600 mA

PHASED OUT




0°

20

20

20 40

40

60

60

80

100

80 100 40 6080100

10°-10° 20°-20°-30°

-40°

-50°

-60°

30°40°

50°

60°

70°

80°

90°-90°0

rela

tive

inet

nsity

[%]

5.2 Light distribution

The optical design of the umodule SLE product line ensures optimumhomogenity for the light distribution.

For further information see Design-in Guide, 3D data and photometric data on www.tridonic.com or on request.


0,3000

0,3050

0,3100

0,3150

0,3200

0,3250

0,3300

0,3350

0,3400

0,29

50

0,30

00

0,30

50

0,31

00

0,31

50

0,32

00

0,32

50

0,33

00

0,33

50

6,500 Kx0 y0

Centre 0.3135 0.3236

380 420 460 500 540 580 620 660 700 740 7800,0

0,1

0,3

0,4

0,6

0,2

0,5

wave length [nm]

norm

. int

ensi

ty [W

/nm

]

PHASED OUT




5.3 Relative luminous flux vs. operating current

Umodule STARK FLE-G1-LES30 at tp=65°C

Umodule STARK FLE-G1-LES40 at tp=65°C

3500

4000

4500

5000

5500

6000

6500

7000

7500

8000

8500

9000

9500

10000

10500

800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800mA

lm

3000 K

4000 K

6500 K

7500

8500

9500

10500

11500

12500

13500

14500

15500

16500

17500

18500

19500

1500 1750 2000 2250 2500 2750 3000 3250 3500 3750mA

lm

3000 K

4000 K

6500 K

PHASED OUT

Documents

LED - tridonic.com · • Luminous flux up to 18,550 lm at tp = 65 °C • High efficacy up to 142 lm/W for the LED module at tp = 25 °C ... 01 02 0403 05 0706 08 09 01 00 Tc [°C]