Embed Size (px)
Citation preview
PRODUCT MANUAL
LED TROLLEY SYSTEM
THE EDGE BELLPARKHORTICULTURE
INDEX2. Product Overview
3. Assembly Instructions
4. Wiring Diagram
5. Light Specifications
7. Trolley Specifications
8. Safety & Care
1
PRODUCT OVERVIEW
1.5
1.0
1.3
1.4
2.0
2.1
2.2
1.1
1. LIGHTS1.0 Daisy chain connectors1.1 Control box sits on the top shelf1.2 Lights mounted with quick clips1.3 LED bars are discreet & low profile1.4 Full spectrum lights are standard1.5 IP67 lights have high water resistance
2. TROLLEY2.0 FDA-approved powder coat finish2.1 Sturdy electro-zinc plated steel shelving, easy to clean and sanitize2.2 German-engineered casters
1.2
2
ASSEMBLY1. Place poles into the base with the holes facing inward. En-
sure that they are right side up, see fig.1 for reference.
2. Install the shelves on the trolley into the pre-cut holes in
the post. The bottom shelf should be installed in the 5th
hole from the base of the post. Each subsequent shelf
should then be installed 8 holes above the previous shelf.
3. Place the smallest shelf on the top of the trolley and place
power/control box on the top, see fig.1 for reference.
4. Begin to mount the light bars onto the shelves using the
quick clip hooks. We recommend that you start with the
top shelf, checking that the wiring matches as you work
your way down. Wires should be on the front of the trol-
leys. See fig.1 for wiring.
5. Daisy chain the wires, feeding them through the poles as
you do so.
6. (Optional) Place white handle and writing board on the
back of the trolley at the desired heights.
3
WIRING DIAGRAMfig.1
By spacing each shelf roughly 14” apart
you will achieve the uniform light levels
required for maximum performance. This
spacing can be achieved by placing the
first shelf in the 5th hole from the bottom
and every shelf after in the 8th hole up.
*Warning: Any modification to the rel-ative shelf heights may change the light diffusion and create hot or cold spots. This may cause plant growth below expectations. If you must modify the spacing of the shelves, contact Bellpark Horticulture so that we can design a solution that works for you.*
4
Light Source LED
Trolley Dimentions (L x W x H) 53.2” x 22.1” x 74.6”
LED Bar Length 51.2”
Trolley Construction Zinc Plated Steel
Trolley Paint FDA Approved Powder Coat
TROLLEY SPECIFICATIONS & DRAWINGS
Optional
5
LED LIGHT SPECTRUM & DRAWINGS
The PFL-s LED lights by Parus, used on the EDGE Trolley, have been carefully designed for a longer period of operation with ideal levels of luminosity for horticultural applications.
6
Product Model Name PFL-s-RBW-1200
Number of Modules 4 Modules Per Array
Power Consumption Max. 240 Watt
Dimentions (LxWxH) 1340mm x 383mm x 45mm Per Module
Weight 16 kg (Array Total)
Power AC Input Power Range 60 Watt Per Module / 240 Watt Total
AC Input Voltage Range Free Volatage 90 ~ 305 VAC, 47~63Hz
SMPS Mode (PSU) DC Current Design (C.V, C.C Mode)
Protection Short Circuit, Overload, Over Voltage
Power Factor Efficiency ≥95%, PFC ≥0.98
Total Harmonic Distortion THD<20%(@load≥50%/115VAC,230VAC; @load≥75%/277VAC)
LEDs Spectrum Ratio (R:W) RBW (W2:R1)
Heat Sink Heat Sink Type Cooling by free air convention
Frame Material
Body Aluminum
PCB Metal PCB (Aluminum)
Heat Conduction 2.0 x/m.k
Thermal Resistance 0.20 0c/w
Efficiency PPF (μmol/s)RBW Spectrum
186 μmol/s per Module / 744 μmol/s Total
PPF/W (μmol/j) 3.1 μmol/j
PPF (μmol m-2 s-1)RBS Spectrum Standard
304 μmol m-2s-1(measure the distance 100mm)225 μmol m-2s-1(measure the distance 150mm)194 μmol m-2s-1(measure the distance 200mm) 178 μmol m-2s-1(measure the distance 300mm)
Control Dimming Control Group Dimming, Wi-Fi Control
Pulse / Duty Rate 400μs / 0~100%
IP Class IP67 Complete protection agaist contact, water projected in po-werful jets agaist the enclosure from any direction shall have
no harmful effects.
Ambient Tempe-rature
Storage Temp, -30°C ~ 85°C
Operation Temp. ~35°C
Angle Lamp Angle 140°
Life Time Life Span Over 50,000hr
Safety Standard CE, EMC, UL, cUL
Warranty 5 years 5 years
Lighting by
LED LIGHT TECHNICAL SPECIFICATIONS
7
i. Please read the manual thoroughly before attempting to assemble or power on the trolley and lights.ii. Ensure that the trolley is connected to a power source of the correct voltage (120V, 60Hz, 1phase).iii. Protect power cables from damage or wear. Only connect the lights to an electrical outlet or extension cord of appropriate type and rating.iv. Please seek service for your trolley in the case of damage or heavy wear including the following: a. Damage to the power supply cord or plug. b. Significant change or drop in performance of the lights.v. Please contact Bellpark Horticulture if you need service: a. [email protected] b. Ph. (604)-385-1155vi. To achieve an optimal lifespan and performance, routinely check for and remove excess dust and debris from around the lights and trolley.vii. Cleaning should always be done with the fixture unplugged from its power source. Do not use high-pressure water to clean the lights.viii. Do not tether more than 4 trolleys together at a time.
SAFETY & CARE
Warning:
Risk of electrical shock.
To reduce the possibility of injury, always unplug the lights before moving or cleaning.
Light bars and power supply are water resistant, not water proof. If these become sub-
merged unplug the lights before removing from the water.
Caution:
To avoid eye damage do not look directly at the lights.
To reduce the risk of overheating, fire or general damage to the LEDs, never place the LED bars face
down on any flush surface. Always allow for adequate ventilation of LED bars and power supply.
8
ContaCt Us
Ph. 604.385.4411
www.bellparkhorticulture.com
[email protected]. 604.385.4411
120-19288 22nd Ave, Surrey BC, Canada. V3Z 3S6
With over 20 years in the horticulture business, Bellpark Horticulture is a trusted name in Horticultural Automation Solutions. Serving growers in Canada and the United States, the Bellpark team strives to provide customers with the highest quality solutions.
Our sales and project consultants realize that each grower is different and that each project requires a personal level of attention to detail to ensure its success.
Our service team is committed to offering our customers the highest level of service with the quickest response time. With a dedicated parts and service department, our factory-trained technicians are available when you need them.
9
