Upload
others
View
9
Download
0
Embed Size (px)
Citation preview
Leica DISTOTM X3The original laser distance meter
Overview 2Technical data 4Instrument Set-up 6Settings 10Operations 27Message Codes 50Care 51Warranty 52Safety instructions 53
Leica DISTO™X3 1
OverviewOv e rv ie w
ComponentsThe Leica DISTO™ is a laser distancemeter oper-ating with a class2 laser. See chapter Technicaldata for scope of use.
1 Display
2 ON/Measure
3 Clear/ OFF
4 Memory/ Navigate upwards
5 Add/ Navigate left
6 Enter/ Equal
7 Selection keys linked to symbolsabove
8 Functions
9 Subtract/ Navigate right
10 Measuring reference/ Navigatedownwards
Basic measuring screen
1 Statusbar
2 Main line
3 Active function
4 Favorites
Leica DISTO™X3 2
Overview
Selection screen
1 Function/ Settings
2 Settings
3 Help function
4 Page indicator
Icons on status barScroll down for further results
Battery power
Bluetooth® is switched on
Bluetooth® connection established
Measuring reference
Device ismeasuringOffset is activated and adds/substractsthe defined value frommeasuring dis-tanceDevice is levelled
Device is not levelled
Leica DISTO™X3 3
Technical dataTe c h n ic a ld a ta
Leica DISTO™X3 4
GeneralAccuracywith favourable conditions * 1mm / 0.04" ***Accuracywith unfavourable conditions ** 2mm / 0.08" ***Range with favourable conditions * 0.05 - 150m / 0.16 - 500ft ***Range with unfavourable conditions ** 0.05 - 80m / 0.16 - 260ft ***Smallest unit displayed 0.1mm / 1/32 inX-Range Power Technology yesLaser class 2Laser type 635 nm, <1mWø laser point | at distances 6 /30 /60mm | 10/ 50/ 100mTilt measuring tolerance to laser beam **** ± 0.2°Tilt measuring tolerance to housing **** ± 0.2°Tilt measuring range **** 360°Protection class IP65 (dust- and splash water protected)Auto. laser switch off after 90 sAuto. power switch off after 180 s
Bluetooth® Smart Bluetooth® v4.0
Power of Bluetooth® Smart 0.71mW
Frequencyof Bluetooth® Smart 2400 - 2483.5MHz
Range of Bluetooth® Smart <10m
Battery durability (2 xAA) up to 4000measurements
Dimension (H xD xW) 132 x56 x29mm | 5.2 x2.2 x1.1 in
Weight (with batteries) 184 g/ 6.49 oz
Temperature range Storage | Operation -25 to 70°C/ -13 to 158°F | -10 to 50°C/ 14 to 122°F
* favourable conditions are: white and diffuse reflecting target (white painted wall), low background illu-mination andmoderate temperatures.** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination ortemperatures at the upper or lower end of the specified temperature range.*** Tolerances apply from 0.05m to 10m with a confidence level of 95%.With favourable conditions the tolerancemay deteriorate by 0.10mm/m for distances above 10m.
With unfavourable conditions the tolerancemay deteriorate by 0.15mm/m for distances above 10m.**** after user calibration. Additional angle related deviation of +/-0.01° per degree up to +/-45° in each quad-rant.Applies at room temperature. For the whole operating temperature range themaximum deviationincreases by +/-0.1°.
Technical data
Leica DISTO™X3 5
FunctionsDistancemeasuring yesMin/Maxmeasuring yesPermanent measuring yesStake out yesAddition/Subtraction yesArea yesRoom angle yesVolume yesPainter function (area with partialmeasurem.) yesPythagoras 3-pointSmart HorizontalMode / Indirect height yesLevel yesMemory yesBeep yesIlluminated colour display yes
Bluetooth® Smart yes
Personalized Favorites yes
Timer yes
Point to point function/ distance yes *****
Smart Area yes *****
***** In combination with Leica DST 360 adapter
Instrument Set-upIn s tru me n tSe t-u p
Introduction
The safety instructions (see SafetyInstructions) and the user manualshould be read through carefullybefore the product is used for the firsttime.
The person responsible for theproduct must ensure that all usersunderstand these directionsandadhere to them.
The symbols used have the followingmeanings:
WARNING
Indicatesa potentially hazardous situ-ation or an unintended use which, ifnot avoided, will result in death or ser-ious injury.
CAUTION
Indicatesa potentially hazardous situ-ation or an unintended use which, ifnot avoided, may result in minor injuryand/or appreciablematerial, financialand environmental damage.
Important paragraphswhichmust be adhered to in practiceas theyenable the product to beused in a technically correct andefficient manner.
6Leica DISTO™X3
Instrument Set-up
Insert batteries
To ensure a reliable use, werecommend using high qualityAlkaline batteries. Change bat-terieswhen battery symbol isflashing.
Switching ON/OFF
Leica DISTO™X3 7
Device is turnedOFF.
Instrument Set-up
Clear
Undo last action. Leave actual function, go to defaultoperationmode.
Message Codes
Leica DISTO™X3 8
If themessage "i" appearswitha number, observe the instruc-tions inMessage Codes section.Example:
Instrument Set-up
Multifunctional endpiece
The orientation of the endpieceis automatically detected andthe zero point is adjusted accord-ingly.
Whenmeasuring with 90°flipped-out endpiece pleasemeake sure that it lies planeagainst the edge youmeasurefrom.
Adjusting measuring reference
Leica DISTO™X3 9
a) Distance ismeasured from therear of the device (standard setting).b) Distance ismeasured from thefront of the device.c) Distance ismeasured from the tri-pod thread.
d) Distance ismeasured from a LeicaDISTOAdapter FTA 360.
Confirm setting.
If device is switched off, ref-erence goesback to standardsetting (rear of the device).
SettingsSe ttin g s
Overview
Tilt units
Distance units
Turning screen**
Beep
Bluetooth®
Bluetooth® settings
Illumination
Favorites
Keypad lock
Tilt calibration
Information / Serial number
Offset
Calibration of DST 360*
Reset
* Activated when connected to Leica DST 360adapter
** Firmware updatemight be required through theLeica DISTO™Plan App to get this feature
10Leica DISTO™X3
Settings
Tilt unitsSwitch between the following units:
360.0°
0.00%
Leica DISTO™X3 11
Confirm setting. Exit settings.
Settings
Distance unitsSwitch between the following units:
0.00m
0.00 ft
0.000m
0.000 in
0.0000m
0'00" 1/32
0.0mm
0 in 1/32
Leica DISTO™X3 12
Confirm setting. Exit settings.
Settings
Turning screen ON/OFF** Firmware updatemight be required through theLeica DISTO™Plan App to get this feature
To switch ON, repeat procedure. Exit settings.
Leica DISTO™X3 13
Settings
Beep ON/OFF
To switch ON, repeat procedure. Exit settings.
Leica DISTO™X3 14
Settings
Bluetooth® ON/OFF
To switch ON, repeat procedure. Exit settings.
Bluetooth® is switched on andblackBluetooth® icon is dis-played in statusbar. If con-nection is established the colorof the icon changes to blue.
Leica DISTO™X3 15
Settings
Bluetooth® Settings
Select ON or OFF.
If device is connected, the favor-ites disappear and two softkeysappear:
If activated inmeasuringmode, itallows the arrow keys tomove thecursor on your computer.
Short press: send the value of themain line to your computer.Long press: send allmeasurementsand results to your computer.
Leica DISTO™X3 16
Confirm setting. Select kind of decimal point for trans-mitted value.
Confirm setting. Select if unit is transmitted or not.
Settings
Confirm setting. Select termination of transmission. Confirm setting. Select if value is transmitted auto-matically or manually.
Leica DISTO™X3 17
Confirm setting. Exit settings.
Settings
Illumination
Select brightness. Confirm setting.
Leica DISTO™X3 18
Exit settings.
To save power reduce bright-ness if not necessary.
Settings
Personalized favorites
Select favorite function. Press selection key left or right. Func-tion is set as favorite above the cor-responding selection key.
Leica DISTO™X3 19
Exit settings.
Select your favorite functions forquick access.Short cut:Press2 secon a selection-key inthemeasuringmode. Selectyour favorite function and pressagain short on the cor-responding selection key.
Settings
De-/Activate keylock
To deactivate, repeat procedure. Thekeylock is active if device is switchedoff.
Exit settings.
Leica DISTO™X3 20
Settings
Calibration of tilt sensor (Tilt Calibration)
Place device on absolutely flat sur-face.
Leica DISTO™X3 21
Turn the device horizontally by180°and place it again on absolutely flatsurface.
Place device on absolutely flat sur-face.
Settings
Turn the device horizontally by180°and place it again on absolutely flatsurface.
After 2 sec the device goesbackto the basicmode.
Leica DISTO™X3 22
Settings
Information
Exit information screen. Exit settings.
Leica DISTO™X3 23
Settings
Offset
Select digit. Adjust digit.
Leica DISTO™X3 24
Approve value. Exit settings.
An offset addsor subtracts aspecified value automatically toor from allmeasurements. Thisfunction allows tolerances to betaken into account. The offseticon is displayed.
Settings
Calibration of Leica DST 360 adapter** Function is activated when connected to the LeicaDST 360 adapter.
Define a point to bemeasured in a dis-tancemore than 8m. Aim at definedpoint and pressDIST button to startthe 5 seconds countdown tomeas-ure.
Leica DISTO™X3 25
Turn the device vertically by180°. Turn the device by180°. Aim again atdefined point and pressDIST buttonto start the 5 seconds countdown tomeasure.
Get more accurate results of thedevice in combination with theLeica DST 360 adapter.
Settings
Reset
Second confirmation with selectionkeys:a) Refuseb) Confirm
Reset returns the instrument tothe factory settings. All cus-tomized settingsandmemoriesare lost.
Leica DISTO™X3 26
OperationsOp e ra tio n s
Overview
Single distancemeasurement
Area
Volume
Room angle
Smart HorizontalMode
Level
Pythagoras (3-point)
Stake out
Timer
Point to point measurement*Point to point measurement lev-elled*Smart areameasurement*/**
* Activated when connected to Leica DST 360adapter
** Firmware updatemight be required through theLeica DISTO™Plan App to get this feature
27Leica DISTO™X3
Operations
Measuring single distance
Aim active laser at target.
Leica DISTO™X3 28
Target surfaces: Measuringerrors can occur whenmeas-uring to colourless liquids, glass,styrofoam or permeable sur-facesor when aiming at highgloss surfaces. Against dark sur-faces themeasuring timeincreases.
Operations
Permanent / Minimum-Maximum measuring
Used tomeasure room diagonals(maximum values) or horizontal dis-tance (minimum values).
Theminimum andmaximum distancemeasured is displayed (min, max.).The last valuemeasured is displayedin themain line.
Use Down navigation key totake over values in themain linefor sending via Bluetooth®Smart.
Stopspermanent / minimum-max-imummeasuring.
Leica DISTO™X3 29
Operations
Add / Subtract
The next measurement is added tothe previousone, respectively sub-tracted from the previousone.
This process can be repeatedas required. The same processcan be used for adding or sub-tracting areasor volumes.
Leica DISTO™X3 30
Operations
Area
The area is calculated based on themathematic termmultiplying 2 dis-tances.
Aim laser at first target point.
Leica DISTO™X3 31
Aim laser at second target point. a) First distanceb) Second distancec) Circumferenced) Area
The result is shown in themainline and themeasured valueabove. Painter function: Press+or - after starting the first meas-urement. Measure and add orsubtract wall lengths. Measurefinally height for second lengthto get the wall area.Use Down navigation key totake over values in themain linefor sending via Bluetooth®Smart.
Operations
Volume
The volume is calculated based onthemathematic termmultiplying 3 dis-tances.
Aim laser at first target point.
Leica DISTO™X3 32
Aim laser at second target point. Aim laser at third target point.
Operations
a) First distanceb) Second distancec) Third distanced) Volume
a) Ceiling/floor areab) Wall areasc) Circumference
Use Down navigation key toshowmore results or to takeover values in themain line forsending via Bluetooth® Smart.
Leica DISTO™X3 33
Operations
Room angle
The angle is calculated based on thecosine rule with 3 known side lengthsof a triangle.
Aim laser at first target point.
Leica DISTO™X3 34
Aim laser at second target point. Aim laser at third target point.
Operations
a) First distanceb) Second distancec) Third distanced) Angle between first and secondmeasurement
a) Circumferenceb) Triangular area
Use Down navigation key toshowmore results or to takeover values in themain line forsending via Bluetooth® Smart.
Leica DISTO™X3 35
Operations
Smart Horizontal Mode
The horizontal distance is calculatedbased on the trigonimetric functioncosine with 1 known length and 1known angle.
Aim laser at target (up to 360° and atransverse tilt of ±10°).
Leica DISTO™X3 36
UseDown navigation key totake over values in themain linefor sending via Bluetooth®Smart.
Operations
Level
Displays inclinationsof 360°.Instrument beepsat 0° and 90°.Ideal for horizontal or verticaladjustments.
Leica DISTO™X3 37
Operations
Pythagoras (3-point)
The distance is calculated based onthe Pythagorean theoremwith 3known lengthsof 2 right-angled tri-angles.
Aim laser at first target.
Leica DISTO™X3 38
Aim laser at second target. Aim laser at third target.
Operations
The result is shown in themainline and themeasured distanceabove. Pressing themeasuringkey for 2 sec in the function activ-atesautomaticallyMinimum orMaximummeasurement.We recommend to use thepythagorasonly for indirect hori-zontalmeasuring. For heightmeasuring (vertical) it ismoreprecise to use a function withinclinationmeasurement.Use Down navigation key totake over values in themain linefor sending via Bluetooth®
Smart.
Leica DISTO™X3 39
Operations
Stake outTwo different distances (a andb) can be entered tomarkoffdefinedmeasured lengths.
Leica DISTO™X3 40
Select digit. Adjust digit. Approve value "a". Adjust value "b".
Operations
Approve value "b" and start meas-urement.
Move device slowly along the stakeout line. The distance to the nextstake out point is displayed.
a) Distance to first stake out pointb) Actual position tomeasured targetc) Distance to second stake out point
Leica DISTO™X3 41
When approaching a stake outpoint to less than 18mm thevalue of the stake out point isfrozen and the arrowson theside change their colour to redfor marking purposes.
The function can be stopped bypressing the CLEAR/OFF but-ton.
Operations
Timer
Select release time. Confirm setting.
The self release starts ifON/Measure key is pressed.
Leica DISTO™X3 42
Operations
Point to point measurement** Function is activated when connected to the LeicaDST 360 adapter.
The tie distance is calculated basedon 2 known coordinateswith x,y and zvalue.
Aim laser at first target point.
Leica DISTO™X3 43
Aim laser at second target point. Use Down navigation key totake over values in themain linefor sending via Bluetooth®Smart.
Operations
If chosen permanent meas-urement for second target point,the actual tie distance is dis-played.
Leica DISTO™X3 44
Operations
Point to point measurement levelled** Function is activated when connected to the LeicaDST 360 adapter.
Use thisPoint to Point measurementfunction to get moremeasuring data.Do not move device after levelling.The tie distance is calculated based
on 2 known coordinateswith x,y and zvalue.
For levelling, device needs to be in aninclination range of +/- 5°.
Rotate the device clockwise 90°. Fol-low the instructionson the display.
Leica DISTO™X3 45
Rotate the device clockwise 90°. Fol-low the instructionson the display.Levelling is finished whenOK iconappears on the display.
Check status line:a) Indicatesproper levellingb) Indicates insufficient levelling
Aim laser at first target point.
Operations
Aim laser at second target point. Use Down navigation key totake over values in themain linefor sending via Bluetooth®Smart.
Leica DISTO™X3 46
If chosen permanent measurementfor second target point, the actual tiedistance is displayed.
Operations
Smart area measurement** Function is activated when connected to the LeicaDST 360 adapter. Firmware updatemight berequired through the Leica DISTO™Plan App to getthis feature.
The area is calculated based on sev-eral known coordinateswith x,y and zvalue.
Aim laser at first target point.
Leica DISTO™X3 47
Aim at andmeasure additional points(max. 30).
a) Circumference of measured area
Use Down navigation key totake over values in themain linefor sending via Bluetooth®Smart.
Operations
Memory (last 20 results)
a) Deletememoryb) Take over value for further actions
Use Down navigation key to showmore detailed results of the specificmeasurement.
Use Left/Right navigation keys toswitch betweenmeasurements.
Leica DISTO™X3 48
Operations
Bluetooth® SmartDISTO™Plan. Use App forBluetooth® data transfer. Yourdevice can be also be updatedthrough thisApp.
Bluetooth® Smart is alwaysact-ive when the device is switchedon. Connect the device withyour smart-phone, tablet,laptop... Measurement valueswill be transferred automaticallyright after ameasurement if"Autosend" is activated. Totransfer a result press the fol-lowing softkey:
Bluetooth® switchesoff as soon asthe laser distancemeter is switchedoff.The efficient and innovativeBluetooth® Smart module (with thenew Bluetooth® standard V4.0)works together with all Bluetooth®Smart Readydevices. All otherBluetooth® devicesdo not supportthe energy saving Bluetooth® SmartModule, which is integrated in thedevice.
We provide no warranty for freeDISTO™software and offer nosupport for it. We accept no liab-ilitywhatsoever arising from theuse of the free software and weare not obliged to provide cor-rectionsnor to developupgrades. Awide range of com-mercial software can be foundon our homepage. Apps forAndroid® or iOS can be found inspecial internet shops. For moredetails, see our homepage.
Leica DISTO™X3 49
Message CodesMe s s a g e Co d e s
Leica DISTO™X3 50
No. Cause Correction
156 Transverse tilt greater than 10° Hold the instrument without any transverse tilt.
162 Calibration error Make sure the device is placed on an absolutely horizontal and flat
204 Calculation error Performmeasurement again.
240 Data transfer error Connect device and repeat procedure
252 Temperature too high Let device cool down.
253 Temperature too low Warm device up.
255 Received signal too weak, measuring time too long Change target surface (e.g. white paper).
256 Received signal too high Change target surface (e.g. white paper) .
257 Toomuch background light Shadow target area.
260 Laser beam interrupted Repeat measurement.
301 Device wasmoved, levelling not valid anymore Perform levelling again. Measuring with invalid levelling is partially
303 Error with Leica DST 360 adapter Repeat measurement.
* If other message codes are displayed frequently even the instrument has been switched off and on, please contact your dealer.
CareCa re
l Clean the device with a damp, soft cloth.
l Never immerse the device in water.
l Never use aggressive cleaning agents orsolvents.
Leica DISTO™X3 51
WarrantyWa rra n ty
International Limited Warranty
The Leica DISTO™comeswith a two year war-ranty from Leica GeosystemsAG. To receive anadditional year warranty, the product must beregistered on our website at http://myworld.leica-geosystems.comwithin eight weeksof the pur-chase date.
If the product is not registered, our two year war-ranty applies.
More detailed information about the InternationalLimitedWarranty can be found on the internet at:www.leica-geo-systems.com/internationalwarranty.
Leica DISTO™X3 52
Safety instructionsSa fe ty in s tru c tio n s
The person responsible for the instrumentmust ensure that all users understand thesedirectionsand adhere to them. The productis permitted to use for skilled personsonly.
Symbols usedThe symbols used have the followingmeanings:
WARNING
Indicatesa potentially hazardous situation or anunintended use which, if not avoided, will result indeath or serious injury.
CAUTION
Indicatesa potentially hazardous situation or anunintended use which, if not avoided, may result inminor injury and/or appreciablematerial, financialand environmental damage.
Important paragraphswhichmust beadhered to in practice as theyenable theproduct to be used in a technically correctand efficient manner.
Leica DISTO™X3 53
Safety instructions
Permitted usel Measuring distances
l Tilt measurement
l Data transfer with Bluetooth®
Prohibited usel Using the product without instruction
l Using outside the stated limits
l Deactivation of safety systemsandremoval of explanatory and hazard labels
l Opening of the equipment byusing tools(screwdrivers, etc.)
l Use of accessories from other man-ufacturerswithout expressapproval
l Carrying out modification or conversionof the product
l Deliberate dazzling of third parties; also inthe dark
l Inadequate safeguardsat the surveyingsite (e.g. whenmeasuring on roads, con-struction sites, etc.)
l Deliberate or irresponsible behaviour onscaffolding, when using ladders, whenmeasuring near machineswhich are run-ning or near parts of machinesor install-ationswhich are unprotected
l Aiming directly in the sun
Hazards in use
WARNING
Watch out for erroneousmeasurements if theinstrument is defective or if it hasbeen dropped orhasbeenmisused or modified. Carry out periodictest measurements. Particularly after the instru-ment hasbeen subject to abnormal use, andbefore, during and after important meas-urements.
CAUTION
Never attempt to repair the product yourself. Incase of damage, contact a local dealer.
WARNING
Changesor modificationsnot expressly approvedcould void the user´s authority to operate theequipment.
CAUTION
Only use chargers recommended by theman-ufacturer to charge the batteries.
Leica DISTO™X3 54
Safety instructions
Limits of use
Refer to section Technical data. The deviceis designed for use in areaspermanently hab-itable byhumans. Do not use the product inexplosion hazardousareasor in aggressiveenvironments.
Areas of responsibility
Responsibilities of the manufacturer of the ori-ginal equipment:
Leica GeosystemsAGHeinrich-Wild-StrasseCH-9435 HeerbruggInternet: www.leica-geosystems.com
The companyabove is responsible for supplyingthe product, including the User Manual in a com-pletely safe condition.
The companyabove is not responsible for thirdparty accessories.
Responsibilities of the person in charge of theinstrument:
l To understand the safety instructionsonthe product and the instructions in theUser Manual.
l To be familiar with local safety regulationsrelating to accident prevention.
l Alwaysprevent access to the product byunauthorised personnel.
Disposal
CAUTION
Flat batteriesmust not be disposed of with house-hold waste. Care for the environment and takethem to the collection points provided in accord-ance with national or local regulations.
The product must not be disposed withhousehold waste. Dispose of the productappropriately in accordance with the nationalregulations in force in your country. Adhereto the national and country specific reg-ulations.
Product specific treatment and wasteman-agement can be downloaded from ourhomepage.
Leica DISTO™X3 55
Safety instructions
Electromagnetic Compatibility(EMC)
WARNING
The device conforms to themost stringent require-ments of the relevant standardsand regulations.However, the possibility of causing interference inother devices cannot be totally excluded.
FCC statement (applicable in U.S.)This equipment hasbeen tested and found to com-plywith the limits for a ClassB digital instrument,pursuant to part 15 of the FCC rules. These limitsare designed to provide reasonable protectionagainst harmful interference in a residential install-ation. This equipment generates, usesand canradiate radio frequencyenergyand, if not installedand used in accordance with the instructions, maycause harmful interference to radio com-munications.
However, there is no guarantee that interferencewill not occur in a particular installation. If this equip-ment does cause harmful interference to radio ortelevision reception, which can be determined byturning the equipment off and on, the user isencouraged to try to correct the interference byone or more of the followingmeasures:
l Reorient or relocate the receivingantenna
l Increase the separation between theequipment and the receiver
l Connect the equipment into an outlet ona circuit different from that to which thereceiver is connected
l Consult the dealer or an experienced radi-o/TV technician for help
This device complieswith part 15 of the FCCrules. Operation is subjected to the following twoconditions:
l This devicemaynot cause harmful inter-ference, and
l this devicemust accept any interferencereceived, including interference that maycause undesired operation.
FCC Radiation Exposure Statement
The radiated rf output power of the instrument isbelow the FCC radio frequencyexposure limits forportable devicesaccording to KDB447498.
Leica DISTO™X3 56
Safety instructions
ISED Statement (applicable inCanada)This device complieswith IndustryCanada'slicense-exempt RSSs. Operation is subject to thefollowing two conditions:
l This devicemaynot cause harmful inter-ference, and
l this devicemust accept any interference,including interference that maycauseundesired operation of the device.
Radio Frequency (RF) Exposure ComplianceStatement
The radiated rf output power of the instrument isbelow the Health Canada'sSafetyCode 6 exclu-sion limit for portable devices (radiated elementseparation distance between the radiating ele-ment and user and/or bystander is below 20 cm).
Japanese Radio Law ComplianceThis device is granted pursuant to the JapaneseRadio Law電波法 . This device should not bemodified otherwise the granted designation num-ber will become invalid.
Use of the product with Bluetooth®
WARNING
Electromagnetic radiation can cause disturbancesin other equipment, in installations (e.g. medicalones such aspacemakers or hearing aids) and inaircraft. It can also affect humansand animals.
Precautions:
Although this product conforms to themost strin-gent standardsand regulations, the possibility ofharm to people and animals cannot be totallyexcluded.
l Do not use the product near petrol sta-tions, chemical plants, in areaswith apotentially explosive atmosphere andwhere blasting takesplace.
l Do not use the product near medicalequipment.
l Do not use the product in airplanes.
l Do not use the product near your bodyfor extended periods.
Leica DISTO™X3 57
Safety instructions
Laser classificationThe device produces visible laser beams, whichare emitted from the instrument: It is a Class2laser product in accordance with:
l IEC60825-1 : 2014 „Radiation safety oflaser products“
Laser Class 2 products:
Do not stare into the laser beam or direct ittowardsother people unnecessarily. Eye pro-tection is normally afforded byaversion responsesincluding the blink reflex.
WARNING
Looking directly into the beamwith optical aids(e.g. binoculars, telescopes) can be hazardous.
CAUTION
Looking into the laser beammaybe hazardous tothe eyes. Don't dazzle other individuals. Paypar-ticular attention to the direction of the laser beamwhen remotely operating the product via an appor software. Ameasurement could be triggered atany time.
Wavelength
620 - 690 nm
Maximum radiant output power for classification
< 1mW
Pulse duration
> 400 ps
Pulse repetition frequency
320MHz
Beam divergence
0.16 x0.6mrad
Leica DISTO™X3 58
Safety instructions
Labelling
Subject to change (drawings, descriptionsandtechnical data) without prior notice.
Leica DISTO™X3 59