Embed Size (px)
Citation preview
LM35
+VS
R1
VOUT
tVS
LM35
+VS
(4 V to 20 V)
OUTPUT
0 mV + 10.0 mV/°C
Product
Folder
Sample &Buy
Technical
Documents
Tools &
Software
Support &Community
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015
LM35 Precision Centigrade Temperature Sensors1 Features 3 Description
The LM35 series are precision integrated-circuit1• Calibrated Directly in Celsius (Centigrade)
temperature devices with an output voltage linearly-• Linear + 10-mV/°C Scale Factor proportional to the Centigrade temperature. The• 0.5°C Ensured Accuracy (at 25°C) LM35 device has an advantage over linear
temperature sensors calibrated in Kelvin, as the user• Rated for Full −55°C to 150°C Rangeis not required to subtract a large constant voltage• Suitable for Remote Applications from the output to obtain convenient Centigrade
• Low-Cost Due to Wafer-Level Trimming scaling. The LM35 device does not require anyexternal calibration or trimming to provide typical• Operates from 4 V to 30 Vaccuracies of ±¼°C at room temperature and ±¾°C• Less than 60-μA Current Drainover a full −55°C to 150°C temperature range. Lower• Low Self-Heating, 0.08°C in Still Air cost is assured by trimming and calibration at the
• Non-Linearity Only ±¼°C Typical wafer level. The low-output impedance, linear output,and precise inherent calibration of the LM35 device• Low-Impedance Output, 0.1 Ω for 1-mA Loadmakes interfacing to readout or control circuitryespecially easy. The device is used with single power2 Applicationssupplies, or with plus and minus supplies. As the
• Power Supplies LM35 device draws only 60 μA from the supply, it hasvery low self-heating of less than 0.1°C in still air. The• Battery ManagementLM35 device is rated to operate over a −55°C to• HVAC 150°C temperature range, while the LM35C device is
• Appliances rated for a −40°C to 110°C range (−10° withimproved accuracy). The LM35-series devices areavailable packaged in hermetic TO transistorpackages, while the LM35C, LM35CA, and LM35Ddevices are available in the plastic TO-92 transistorpackage. The LM35D device is available in an 8-leadsurface-mount small-outline package and a plasticTO-220 package.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)TO-CAN (3) 4.699 mm × 4.699 mmTO-92 (3) 4.30 mm × 4.30 mm
LM35SOIC (8) 4.90 mm × 3.91 mmTO-220 (3) 14.986 mm × 10.16 mm
(1) For all available packages, see the orderable addendum atthe end of the datasheet.
Basic Centigrade Temperature SensorFull-Range Centigrade Temperature Sensor(2°C to 150°C)
Choose R1 = –VS / 50 µAVOUT = 1500 mV at 150°CVOUT = 250 mV at 25°CVOUT = –550 mV at –55°C
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
Table of Contents7.2 Functional Block Diagram ....................................... 131 Features .................................................................. 17.3 Feature Description................................................. 132 Applications ........................................................... 17.4 Device Functional Modes........................................ 133 Description ............................................................. 1
8 Application and Implementation ........................ 144 Revision History..................................................... 28.1 Application Information............................................ 145 Pin Configuration and Functions ......................... 38.2 Typical Application .................................................. 156 Specifications......................................................... 48.3 System Examples ................................................... 166.1 Absolute Maximum Ratings ...................................... 4
9 Power Supply Recommendations ...................... 196.2 ESD Ratings.............................................................. 410 Layout................................................................... 196.3 Recommended Operating Conditions....................... 4
10.1 Layout Guidelines ................................................. 196.4 Thermal Information .................................................. 410.2 Layout Example .................................................... 206.5 Electrical Characteristics: LM35A, LM35CA Limits... 5
11 Device and Documentation Support ................. 216.6 Electrical Characteristics: LM35A, LM35CA ............. 611.1 Trademarks ........................................................... 216.7 Electrical Characteristics: LM35, LM35C, LM35D
Limits.......................................................................... 8 11.2 Electrostatic Discharge Caution............................ 216.8 Electrical Characteristics: LM35, LM35C, LM35D ... 9 11.3 Glossary ................................................................ 216.9 Typical Characteristics ............................................ 11 12 Mechanical, Packaging, and Orderable
Information ........................................................... 217 Detailed Description ............................................ 137.1 Overview ................................................................. 13
4 Revision History
Changes from Revision D (October 2013) to Revision E Page
• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device FunctionalModes, Application and Implementation section, Power Supply Recommendations section, Layout section, Deviceand Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision C (July 2013) to Revision D Page
• Changed W to Ω .................................................................................................................................................................... 1• Changed W to Ω in Abs Max tablenote. ................................................................................................................................ 4
2 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
+VS VOUT GND
+VSVOUT
GND
N.C.
N.C.
N.C.
N.C.
N.C.
12
3
4
87
6
5
+VS VOUT
GND
LM35DT
+VS VOUT
GND t
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
5 Pin Configuration and Functions
NDV PackageNEB Package3-Pin TO-CAN3-Pin TO-220(Top View)(Top View)
Case is connected to negative pin (GND)
D Package8-PIN SOIC(Top View)
Tab is connected to the negative pin(GND).NOTE: The LM35DT pinout is different thanN.C. = No connectionthe discontinued LM35DP
LP Package3-Pin TO-92
(Bottom View)
Pin FunctionsPIN
TYPE DESCRIPTIONNAME TO46 TO92 TO220 SO8VOUT — — — 1 O Temperature Sensor Analog Output
— — — 2N.C. — No Connection
— — — 3Device ground pin, connect to power supply negativeGND — — — 4 GROUND terminal
— — — 5N.C. — — — 6 — No Connection
— — — 7+VS — — — 8 POWER Positive power supply pin
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM35
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
6 Specifications
6.1 Absolute Maximum Ratingsover operating free-air temperature range (unless otherwise noted) (1) (2)
MIN MAX UNITSupply voltage –0.2 35 VOutput voltage –1 6 VOutput current 10 mAMaximum Junction Temperature, TJmax 150 °C
TO-CAN, TO-92 Package –60 150Storage Temperature, Tstg °C
TO-220, SOIC Package –65 150
(1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability andspecifications.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do notapply when operating the device beyond its rated operating conditions.
6.2 ESD RatingsVALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2500 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditionsover operating free-air temperature range (unless otherwise noted)
MIN MAX UNITLM35, LM35A –55 150
Specified operating temperature: TMIN to LM35C, LM35CA –40 110 °CTMAXLM35D 0 100
Supply Voltage (+VS) 4 30 V
6.4 Thermal InformationLM35
THERMAL METRIC (1) (2) NDV LP D NEB UNIT3 PINS 8 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance 400 180 220 90°C/W
RθJC(top) Junction-to-case (top) thermal resistance 24 — — —
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.(2) For additional thermal resistance information, see Typical Application.
4 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
6.5 Electrical Characteristics: LM35A, LM35CA LimitsUnless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for theLM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-RangeCentigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35A LM35CAPARAMETER TEST CONDITIONS UNITTYP TESTED DESIGN TYP TESTED DESIGN
LIMIT (1) LIMIT (2) LIMIT (1) LIMIT (2)
TA = 25°C ±0.2 ±0.5 ±0.2 ±0.5TA = –10°C ±0.3 ±0.3 ±1
Accuracy (3) °CTA = TMAX ±0.4 ±1 ±0.4 ±1TA = TMIN ±0.4 ±1 ±0.4 ±1.5TMIN ≤ TA ≤ TMAX,Nonlinearity (4) ±0.18 ±0.35 ±0.15 ±0.3 °C–40°C ≤ TJ ≤ 125°CTMIN ≤ TA ≤ TMAX 10 9.9 10 9.9Sensor gain mV/°C(average slope) –40°C ≤ TJ ≤ 125°C 10 10.1 10 10.1TA = 25°C ±0.4 ±1 ±0.4 ±1
Load regulation (5)mV/mATMIN ≤ TA ≤ TMAX,0 ≤ IL ≤ 1 mA ±0.5 ±3 ±0.5 ±3–40°C ≤ TJ ≤ 125°C
TA = 25°C ±0.01 ±0.05 ±0.01 ±0.05Line regulation (5) mV/V4 V ≤ VS ≤ 30 V, ±0.02 ±0.1 ±0.02 ±0.1–40°C ≤ TJ ≤ 125°C
VS = 5 V, 25°C 56 67 56 67VS = 5 V, –40°C ≤ TJ ≤ 125°C 105 131 91 114
Quiescent current (6) µAVS = 30 V, 25°C 56.2 68 56.2 68VS = 30 V, –40°C ≤ TJ ≤ 125°C 105.5 133 91.5 1164 V ≤ VS ≤ 30 V, 25°C 0.2 1 0.2 1
Change of quiescent µA4 V ≤ VS ≤ 30 V,current (5) 0.5 2 0.5 2–40°C ≤ TJ ≤ 125°CTemperaturecoefficient of –40°C ≤ TJ ≤ 125°C 0.39 0.5 0.39 0.5 µA/°Cquiescent currentMinimum temperature In circuit of Figure 14, IL = 0 1.5 2 1.5 2 °Cfor rate accuracyLong term stability TJ = TMAX, for 1000 hours ±0.08 ±0.08 °C
(1) Tested Limits are ensured and 100% tested in production.(2) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.(3) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.(6) Quiescent current is defined in the circuit of Figure 14.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM35
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
6.6 Electrical Characteristics: LM35A, LM35CAUnless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for theLM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-RangeCentigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35A LM35CAPARAMETER TEST CONDITIONS UNIT
MIN TYP MAX TYP TYP MAX±0.2 ±0.2
TA = 25°C Tested Limit (2) ±0.5 ±0.5Design Limit (3)
±0.3 ±0.3TA = –10°C Tested Limit (2)
Design Limit (3) ±1Accuracy (1) °C
±0.4 ±0.4TA = TMAX Tested Limit (2) ±1 ±1
Design Limit (3)
±0.4 ±0.4TA = TMIN Tested Limit (2) ±1
Design Limit (3) ±1.5±0.18 ±0.15
TMIN ≤ TA ≤ TMAX,Nonlinearity (4) Tested Limit (2) °C–40°C ≤ TJ ≤ 125°CDesign Limit (3) ±0.35 ±0.3
10 10TMIN ≤ TA ≤ TMAX Tested Limit (2) 9.9
Design Limit (3) 9.9Sensor gain mV/°C(average slope) 10 10–40°C ≤ TJ ≤ 125°C Tested Limit (2) 10.1
Design Limit (3) 10.1±0.4 ±0.4
TA = 25°C Tested Limit (2) ±1 ±1Design Limit (3)Load regulation (5)
mV/mA0 ≤ IL ≤ 1 mA ±0.5 ±0.5TMIN ≤ TA ≤ TMAX, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±3 ±3±0.01 ±0.01
TA = 25°C Tested Limit (2) ±0.05 ±0.05Design Limit (3)
Line regulation (5) mV/V±0.02 ±0.02
4 V ≤ VS ≤ 30 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±0.1 ±0.1
(1) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specifiedconditions of voltage, current, and temperature (expressed in °C).
(2) Tested Limits are ensured and 100% tested in production.(3) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
6 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
Electrical Characteristics: LM35A, LM35CA (continued)Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for theLM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-RangeCentigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35A LM35CAPARAMETER TEST CONDITIONS UNIT
MIN TYP MAX TYP TYP MAX56 56
VS = 5 V, 25°C Tested Limit (2) 67 67Design Limit (3)
105 91VS = 5 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) 131 114Quiescent µAcurrent (6) 56.2 56.2VS = 30 V, 25°C Tested Limit (2) 68 68
Design Limit (3)
105.5 91.5VS = 30 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) 133 1160.2 0.2
4 V ≤ VS ≤ 30 V, 25°C Tested Limit (2) 1 1Change of Design Limit (3)quiescent µA
0.5 0.5current (5)4 V ≤ VS ≤ 30 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) 2 20.39 0.39Temperature
coefficient of –40°C ≤ TJ ≤ 125°C Tested Limit (2) µA/°Cquiescent current Design Limit (3) 0.5 0.5
1.5 1.5Minimum In circuit of Figure 14, IL =temperature for Tested Limit (2) °C0rate accuracy Design Limit (3) 2 2Long term ±0.08 ±0.08TJ = TMAX, for 1000 hours °Cstability
(6) Quiescent current is defined in the circuit of Figure 14.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM35
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
6.7 Electrical Characteristics: LM35, LM35C, LM35D LimitsUnless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for theLM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-RangeCentigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35 LM35C, LM35DPARAMETER TEST CONDITIONS UNITTYP TESTED DESIGN TYP TESTED DESIGN
LIMIT (1) LIMIT (2) LIMIT (1) LIMIT (2)
TA = 25°C ±0.4 ±1 ±0.4 ±1TA = –10°C ±0.5 ±0.5 ±1.5Accuracy, LM35, °CLM35C (3) TA = TMAX ±0.8 ±1.5 ±0.8 ±1.5TA = TMIN ±0.8 ±1.5 ±0.8 ±2TA = 25°C ±0.6 ±1.5
Accuracy, LM35D (3) TA = TMAX ±0.9 ±2 °CTA = TMIN ±0.9 ±2TMIN ≤ TA ≤ TMAX,Nonlinearity (4) ±0.3 ±0.5 ±0.2 ±0.5 °C–40°C ≤ TJ ≤ 125°CTMIN ≤ TA ≤ TMAX, 10 9.8 10 9.8Sensor gain –40°C ≤ TJ ≤ 125°C mV/°C(average slope)
10 10.2 10 10.2TA = 25°C ±0.4 ±2 ±0.4 ±2
Load regulation (5)mV/mATMIN ≤ TA ≤ TMAX,0 ≤ IL ≤ 1 mA ±0.5 ±5 ±0.5 ±5–40°C ≤ TJ ≤ 125°C
TA = 25°C ±0.01 ±0.1 ±0.01 ±0.1Line regulation (5) mV/V4 V ≤ VS ≤ 30 V, ±0.02 ±0.2 ±0.02 ±0.2–40°C ≤ TJ ≤ 125°C
VS = 5 V, 25°C 56 80 56 80VS = 5 V, –40°C ≤ TJ ≤ 125°C 105 158 91 138
Quiescent current (6) µAVS = 30 V, 25°C 56.2 82 56.2 82VS = 30 V, –40°C ≤ TJ ≤ 125°C 105.5 161 91.5 1414 V ≤ VS ≤ 30 V, 25°C 0.2 2 0.2 2
Change of quiescent µA4 V ≤ VS ≤ 30 V,current (5) 0.5 3 0.5 3–40°C ≤ TJ ≤ 125°CTemperaturecoefficient of –40°C ≤ TJ ≤ 125°C 0.39 0.7 0.39 0.7 µA/°Cquiescent currentMinimum temperature In circuit of Figure 14, IL = 0 1.5 2 1.5 2 °Cfor rate accuracyLong term stability TJ = TMAX, for 1000 hours ±0.08 ±0.08 °C
(1) Tested Limits are ensured and 100% tested in production.(2) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.(3) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.(6) Quiescent current is defined in the circuit of Figure 14.
8 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
6.8 Electrical Characteristics: LM35, LM35C, LM35DUnless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for theLM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-RangeCentigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35 LM35C, LM35DPARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX±0.4 ±0.4
TA = 25°C Tested Limit (2) ±1 ±1Design Limit (3)
±0.5 ±0.5TA = –10°C Tested Limit (2)
Design Limit (3) ±1.5Accuracy, LM35, °CLM35C (1) ±0.8 ±0.8TA = TMAX Tested Limit (2) ±1.5
Design Limit (3) ±1.5±0.8 ±0.8
TA = TMIN Tested Limit (2)
Design Limit (3) ±1.5 ±2±0.6
TA = 25°C Tested Limit (2) ±1.5Design Limit (3)
±0.9Accuracy, TA = TMAX Tested Limit (2) °CLM35D (1)
Design Limit (3) ±2±0.9
TA = TMIN Tested Limit (2)
Design Limit (3) ±2±0.3 ±0.2
TMIN ≤ TA ≤ TMAX,Nonlinearity (4) Tested Limit (2) °C–40°C ≤ TJ ≤ 125°CDesign Limit (3) ±0.5 ±0.5
10 10TMIN ≤ TA ≤ TMAX, Tested Limit (2) 9.8–40°C ≤ TJ ≤ 125°C
Design Limit (3) 9.8Sensor gain mV/°C(average slope) 10 10Tested Limit (2) 10.2Design Limit (3) 10.2
±0.4 ±0.4TA = 25°C Tested Limit (2) ±2 ±2
Design Limit (3)Load regulation (5)mV/mA0 ≤ IL ≤ 1 mA ±0.5 ±0.5
TMIN ≤ TA ≤ TMAX, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±5 ±5
(1) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specifiedconditions of voltage, current, and temperature (expressed in °C).
(2) Tested Limits are ensured and 100% tested in production.(3) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM35
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
Electrical Characteristics: LM35, LM35C, LM35D (continued)Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for theLM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-RangeCentigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35 LM35C, LM35DPARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX±0.01 ±0.01
TA = 25°C Tested Limit (2) ±0.1Design Limit (3) ±0.1
Line regulation (5) mV/V±0.02 ±0.02
4 V ≤ VS ≤ 30 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±0.2 ±0.256 56
VS = 5 V, 25°C Tested Limit (2) 80 80Design Limit (3)
105 91VS = 5 V, –40°C ≤ TJ ≤ Tested Limit (2)125°C
Design Limit (3) 158 138Quiescent µAcurrent (6) 56.2 56.2VS = 30 V, 25°C Tested Limit (2) 82 82
Design Limit (3)
105.5 91.5VS = 30 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) 161 1410.2 0.2
4 V ≤ VS ≤ 30 V, 25°C Tested Limit (2) 2Change of Design Limit (3) 2quiescent µA
0.5 0.5current (5)4 V ≤ VS ≤ 30 V, Tested Limit (2)–40°C ≤ TJ ≤ 125°C
Design Limit (3) 3 30.39 0.39Temperature
coefficient of –40°C ≤ TJ ≤ 125°C Tested Limit (2) µA/°Cquiescent current Design Limit (3) 0.7 0.7
1.5 1.5Minimumtemperature for In circuit of Figure 14, IL = 0 Tested Limit (2) °Crate accuracy Design Limit (3) 2 2Long term ±0.08 ±0.08TJ = TMAX, for 1000 hours °Cstability
(6) Quiescent current is defined in the circuit of Figure 14.
10 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
0
20
40
60
80
100
120
140
160
±75 ±25 25 75 125 175
QU
IES
CE
NT
CU
RR
EN
T (�
A)
TEMPERATURE (�C) C006
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
4.0
4.2
4.4
±75 ±25 25 75 125 175
SU
PP
LY V
OLT
AG
E (
V)
TEMPERATURE (�C) C005
TYPICAL IOUT = 2.0 mA
TYPICAL IOUT = 1.0 mA
TYPICAL IOUT = 0 �A or 50 �A
±20
0
20
40
60
80
100
120
0 2 4 6 8
PE
RC
EN
T O
F F
INA
L V
ALU
E (
%)
TIME (MINUTES) C003
±20
0
20
40
60
80
100
120
0 2 4 6 8
PE
RC
EN
T O
F F
INA
L V
ALU
E (
%)
TIME (SEC) C004
T0-46
T0-92
0
100
200
300
400
0 400 800 1200 1600 2000
TH
ER
MA
L R
ES
IST
AN
CE
(�C
/W)
AIR VELOCITY (FPM) C001
T0-46
T0-92
0
5
10
15
20
25
30
35
40
45
0 400 800 1200 1600 2000
TIM
E C
ON
ST
AN
T (
SE
C)
AIR VELOCITY (FPM) C002
T0-46
T0-92
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
6.9 Typical Characteristics
Figure 1. Thermal Resistance Junction To Air Figure 2. Thermal Time Constant
Figure 3. Thermal Response In Still Air Figure 4. Thermal Response In Stirred Oil Bath
Figure 5. Minimum Supply Voltage vs Temperature Figure 6. Quiescent Current vs Temperature (in Circuit ofFigure 14)
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM35
-20 -10 0 10 20 30 40 50 60 -0.2
0
0.2
0.4
0.6
0
2
4
6
TIME (�SEC) C011
VO
UT (
V)
VIN
(V
)
±2.5
±2.0
±1.5
±1.0
±0.5
0.0
0.5
1.0
1.5
2.0
2.5
±75 ±25 25 75 125 175
TE
MP
ER
AT
UR
E E
RR
OR
(�C
)
TEMPERATURE (�C) C009
LM35C
LM35CA
LM35D
LM35C
TYPICAL LM35CA
10 100 1k 10k 100k 0
200
400
600
800
1000
1200
1400
1600
Noi
se (
nV/�
Hz)
FREQUENCY (Hz) C010
40
60
80
100
120
140
160
180
200
±75 ±25 25 75 125 175
QU
IES
CE
NT
CU
RR
EN
T (�
A)
TEMPERATURE (�C) C007
±2.0
±1.5
±1.0
±0.5
0.0
0.5
1.0
1.5
2.0
±75 ±25 25 75 125 175
TE
MP
ER
AT
UR
E E
RR
OR
(�C
)
TEMPERATURE (�C) C008
LM35
LM35A
LM35
LM35A TYPICAL
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
Typical Characteristics (continued)
Figure 7. Quiescent Current vs Temperature (in Circuit of Figure 8. Accuracy vs Temperature (Ensured)Full-Range Centigrade Temperature Sensor)
Figure 10. Noise VoltageFigure 9. Accuracy vs Temperature (Ensured)
Figure 11. Start-Up Response
12 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
.125 R2
VOUT = 10 mV/°C
+
+VS
R2
A2
A1
V0
nR1
i
8.8 mV/°C
nR1Q1 Q2
10E E
1.38 VPTAT
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
7 Detailed Description
7.1 OverviewThe LM35-series devices are precision integrated-circuit temperature sensors, with an output voltage linearlyproportional to the Centigrade temperature. The LM35 device has an advantage over linear temperature sensorscalibrated in Kelvin, as the user is not required to subtract a large constant voltage from the output to obtainconvenient Centigrade scaling. The LM35 device does not require any external calibration or trimming to providetypical accuracies of ± ¼ °C at room temperature and ± ¾ °C over a full −55°C to 150°C temperature range.Lower cost is assured by trimming and calibration at the wafer level. The low output impedance, linear output,and precise inherent calibration of the LM35 device makes interfacing to readout or control circuitry especiallyeasy. The device is used with single power supplies, or with plus and minus supplies. As the LM35 device drawsonly 60 μA from the supply, it has very low self-heating of less than 0.1°C in still air. The LM35 device is rated tooperate over a −55°C to 150°C temperature range, while the LM35C device is rated for a −40°C to 110°C range(−10° with improved accuracy). The temperature-sensing element is comprised of a delta-V BE architecture.
The temperature-sensing element is then buffered by an amplifier and provided to the VOUT pin. The amplifierhas a simple class A output stage with typical 0.5-Ω output impedance as shown in the Functional BlockDiagram. Therefore the LM35 can only source current and it's sinking capability is limited to 1 μA.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 LM35 Transfer FunctionThe accuracy specifications of the LM35 are given with respect to a simple linear transfer function:
VOUT = 10 mv/°F × T
where• VOUT is the LM35 output voltage• T is the temperature in °C (1)
7.4 Device Functional ModesThe only functional mode of the LM35 is that it has an analog output directly proportional to temperature.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM35
LM35
+
OUT
HEAVY CAPACITIVE LOAD, WIRING, ETC.
TO A HIGH-IMPEDANCE LOAD
v75
1 PF
0.01 PF BYPASSOPTONAL
LM35
+
OUT
2 k
HEAVY CAPACITIVE LOAD, WIRING, ETC.
TO A HIGH-IMPEDANCE LOAD
v
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
8 Application and Implementation
NOTEInformation in the following applications sections is not part of the TI componentspecification, and TI does not warrant its accuracy or completeness. TI’s customers areresponsible for determining suitability of components for their purposes. Customers shouldvalidate and test their design implementation to confirm system functionality.
8.1 Application InformationThe features of the LM35 make it suitable for many general temperature sensing applications. Multiple packageoptions expand on it's flexibility.
8.1.1 Capacitive Drive CapabilityLike most micropower circuits, the LM35 device has a limited ability to drive heavy capacitive loads. Alone, theLM35 device is able to drive 50 pF without special precautions. If heavier loads are anticipated, isolating ordecoupling the load with a resistor is easy (see Figure 12). The tolerance of capacitance can be improved with aseries R-C damper from output to ground (see Figure 13).
When the LM35 device is applied with a 200-Ω load resistor as shown in Figure 16, Figure 17, or Figure 19, thedevice is relatively immune to wiring capacitance because the capacitance forms a bypass from ground to inputand not on the output. However, as with any linear circuit connected to wires in a hostile environment,performance is affected adversely by intense electromagnetic sources (such as relays, radio transmitters, motorswith arcing brushes, and SCR transients), because the wiring acts as a receiving antenna and the internaljunctions act as rectifiers. For best results in such cases, a bypass capacitor from VIN to ground and a series R-Cdamper, such as 75 Ω in series with 0.2 or 1 μF from output to ground, are often useful. Examples are shown inFigure 13, Figure 24, and Figure 25.
Figure 12. LM35 with Decoupling from Capacitive Load
Figure 13. LM35 with R-C Damper
14 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
±2.0
±1.5
±1.0
±0.5
0.0
0.5
1.0
1.5
2.0
±75 ±25 25 75 125 175
TE
MP
ER
AT
UR
E E
RR
OR
(�C
)
TEMPERATURE (�C) C008
LM35
LM35A
LM35
LM35A TYPICAL
LM35
+VS
(4 V to 20 V)
OUTPUT
0 mV + 10.0 mV/°C
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
8.2 Typical Application
8.2.1 Basic Centigrade Temperature Sensor
Figure 14. Basic Centigrade Temperature Sensor (2 °C to 150 °C)
8.2.1.1 Design Requirements
Table 1. Design ParametersPARAMETER VALUE
Accuracy at 25°C ±0.5°CAccuracy from –55 °C to 150°C ±1°C
Temperature Slope 10 mV/°C
8.2.1.2 Detailed Design ProcedureBecause the LM35 device is a simple temperature sensor that provides an analog output, design requirementsrelated to layout are more important than electrical requirements. For a detailed description, refer to the Layout.
8.2.1.3 Application Curve
Figure 15. Accuracy vs Temperature (Ensured)
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM35
+VS
LM35
18 k
10%
VOUT
+
v
1N914
LM35
+
OUT
VOUT = 10 mV/°C (TAMBIENT = 10 °C)
FROM t 5 °C TO + 40 °C
5 V
200
1%
200
1%
TWISTED PAIR0.01 PF
BYPASSOPTIONAL
2 k
1%
2 k
1%
LM35
+
OUT
VOUT = 10 mV/°C (TAMBIENT = 1 °C)
FROM + 2 °C TO + 40 °C
v
5 V
200
1%
6.8 k
5%
200
1%
TWISTED PAIR
HEAT
FINS
+
v
LM35
+
OUT
VOUT = 10 mV/°C (TAMBIENT = 1 °C)
FROM + 2 °C TO + 40 °C
v
5 V
200
1%
6.8 k
5%
OR 10K RHEOSTAT
FOR GAIN ADJUST
200
1%
TWISTED PAIR
HEAT
FINS
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
8.3 System Examples
Figure 16. Two-Wire Remote Temperature Sensor Figure 17. Two-Wire Remote Temperature Sensor(Grounded Sensor) (Output Referred to Ground)
Figure 18. Temperature Sensor, Single Supply Figure 19. Two-Wire Remote Temperature Sensor(−55° to +150°C) (Output Referred to Ground)
16 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
LM35
9 V
1 k
25.5 kLM385-2.5
100 �A,60 mVFULL-SCALE
LM35
5 V
LM35
+VS
(6 V to 20 V)
45.5 kO
1%
10 kO
1%
26.4 kO
1%
1 MO
1%
18 kOLM385-1.2
VOUT = +1 mV/°F
LM35 LM317
402
1%
50
OUT
OFFSET
ADJUST
+
v
OUT
62.5
0.5%
4.7 k
IN
ADJ
+ 5 V TO + 30 V
2N2907
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
System Examples (continued)
Figure 20. 4-To-20 mA Current Source Figure 21. Fahrenheit Thermometer(0°C to 100°C)
Figure 22. Centigrade Thermometer Figure 23. Fahrenheit Thermometer, ExpandedScale Thermometer(Analog Meter)
(50°F to 80°F, for Example Shown)
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM35
LM35
+
OUT
200*
1.5 k*
HEAT
FINS
VA
RA
1 k
1 PF+
20 PF+
LM3914 LM3914
1.2 k*
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86
10
20 k
18
1 2 3
7 V
4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
NC
VBVC
499*499*
10 18
7 V
7 V
1.5 k*
RC
1 k
1 k*
RB
1 k
20 LEDs
°F
LM35LM131
47
+
GND
8
6 V
100 k
0.01 PF100 k 1 PF
12 k
5 k
FULLSCALEADJ
1 2 4
6
7
0.01 PF
LOW TEMPCO
3
5
1 k6.8 k
4N28
fOUT
LM35
+
OUT
GND
75
1 PF
16 k
ADC0804
+2 k
1 k +
IN
VREF
0.64 V
5 V
8PARALLEL
DATA
OUTPUT
INTR
CS
RD
WR
GND
LM35
+
OUT
GND
75
1 PF
3.9 k
+
10 k
100k+
IN
5 V
SERIAL
DATA OUTPUT
CLOCK
ENABLE
GND
ADC08031
LM385FB
REF
1.28 V
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
System Examples (continued)
Figure 24. Temperature to Digital Converter Figure 25. Temperature to Digital Converter(Serial Output) (Parallel TRI-STATE Outputs for Standard Data Bus
to μP Interface)(128°C Full Scale)(128°C Full Scale)
*=1% or 2% film resistorTrim RB for VB = 3.075 VTrim RC for VC = 1.955 VTrim RA for VA = 0.075 V + 100 mV/°C ×Tambient
Example, VA = 2.275 V at 22°C
Figure 26. Bar-Graph Temperature Display Figure 27. LM35 With Voltage-To-FrequencyConverter and Isolated Output(Dot Mode)(2°C to 150°C; 20 to 1500 Hz)
18 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
9 Power Supply RecommendationsThe LM35 device has a very wide 4-V to 5.5-V power supply voltage range, which makes it ideal for manyapplications. In noisy environments, TI recommends adding a 0.1 μF from V+ to GND to bypass the powersupply voltage. Larger capacitances maybe required and are dependent on the power-supply noise.
10 Layout
10.1 Layout GuidelinesThe LM35 is easily applied in the same way as other integrated-circuit temperature sensors. Glue or cement thedevice to a surface and the temperature should be within about 0.01°C of the surface temperature.
The 0.01°C proximity presumes that the ambient air temperature is almost the same as the surface temperature.If the air temperature were much higher or lower than the surface temperature, the actual temperature of theLM35 die would be at an intermediate temperature between the surface temperature and the air temperature;this is especially true for the TO-92 plastic package. The copper leads in the TO-92 package are the principalthermal path to carry heat into the device, so its temperature might be closer to the air temperature than to thesurface temperature.
Ensure that the wiring leaving the LM35 device is held at the same temperature as the surface of interest tominimize the temperature problem. The easiest fix is to cover up these wires with a bead of epoxy. The epoxybead will ensure that the leads and wires are all at the same temperature as the surface, and that thetemperature of the LM35 die is not affected by the air temperature.
The TO-46 metal package can also be soldered to a metal surface or pipe without damage. Of course, in thatcase the V− terminal of the circuit will be grounded to that metal. Alternatively, mount the LM35 inside a sealed-end metal tube, and then dip into a bath or screw into a threaded hole in a tank. As with any IC, the LM35 deviceand accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This isespecially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuitcoatings and varnishes such as a conformal coating and epoxy paints or dips are often used to insure thatmoisture cannot corrode the LM35 device or its connections.
These devices are sometimes soldered to a small light-weight heat fin to decrease the thermal time constant andspeed up the response in slowly-moving air. On the other hand, a small thermal mass may be added to thesensor, to give the steadiest reading despite small deviations in the air temperature.
Table 2. Temperature Rise of LM35 Due To Self-heating (Thermal Resistance, RθJA)SOIC-8 (2),TO, no heat TO (1), small TO-92, no heat TO-92 (2), small SOIC-8, no TO-220, nosmall heatsink heat fin sink heat fin heat sink heat sinkfin
Still air 400°C/W 100°C/W 180°C/W 140°C/W 220°C/W 110°C/W 90°C/WMoving air 100°C/W 40°C/W 90°C/W 70°C/W 105°C/W 90°C/W 26°C/WStill oil 100°C/W 40°C/W 90°C/W 70°C/W — — —Stirred oil 50°C/W 30°C/W 45°C/W 40°C/W — — —(Clamped tometal, Infinite (24°C/W) — — (55°C/W) —heat sink)
(1) Wakefield type 201, or 1-in disc of 0.02-in sheet brass, soldered to case, or similar.(2) TO-92 and SOIC-8 packages glued and leads soldered to 1-in square of 1/16-in printed circuit board with 2-oz foil or similar.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM35
VOUT
N.C.
N.C.
+VS
N.C.
0.01 µF
VIA to ground plane
VIA to power plane
GND N.C.
N.C.
LM35SNIS159E –AUGUST 1999–REVISED JANUARY 2015 www.ti.com
10.2 Layout Example
Figure 28. Layout Example
20 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM35
LM35www.ti.com SNIS159E –AUGUST 1999–REVISED JANUARY 2015
11 Device and Documentation Support
11.1 TrademarksAll trademarks are the property of their respective owners.
11.2 Electrostatic Discharge CautionThese devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foamduring storage or handling to prevent electrostatic damage to the MOS gates.
11.3 GlossarySLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable InformationThe following pages include mechanical, packaging, and orderable information. This information is the mostcurrent data available for the designated devices. This data is subject to change without notice and revision ofthis document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM35
PACKAGE OPTION ADDENDUM
www.ti.com 8-Apr-2015
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
LM35AH ACTIVE TO NDV 3 1000 TBD Call TI Call TI -55 to 150 ( LM35AH ~ LM35AH)
LM35AH/NOPB ACTIVE TO NDV 3 1000 Green (RoHS& no Sb/Br)
Call TI Level-1-NA-UNLIM -55 to 150 ( LM35AH ~ LM35AH)
LM35CAH ACTIVE TO NDV 3 1000 TBD Call TI Call TI -40 to 110 ( LM35CAH ~ LM35CAH)
LM35CAH/NOPB ACTIVE TO NDV 3 1000 Green (RoHS& no Sb/Br)
Call TI Level-1-NA-UNLIM -40 to 110 ( LM35CAH ~ LM35CAH)
LM35CAZ/LFT4 ACTIVE TO-92 LP 3 2000 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type LM35CAZ
LM35CAZ/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type -40 to 110 LM35CAZ
LM35CH ACTIVE TO NDV 3 1000 TBD Call TI Call TI -40 to 110 ( LM35CH ~ LM35CH)
LM35CH/NOPB ACTIVE TO NDV 3 1000 Green (RoHS& no Sb/Br)
Call TI Level-1-NA-UNLIM -40 to 110 ( LM35CH ~ LM35CH)
LM35CZ/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type LM35CZ
LM35CZ/LFT4 ACTIVE TO-92 LP 3 2000 TBD Call TI Call TI
LM35CZ/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type -40 to 110 LM35CZ
LM35DH ACTIVE TO NDV 3 1000 TBD Call TI Call TI 0 to 70 ( LM35DH ~ LM35DH)
LM35DH/NOPB ACTIVE TO NDV 3 1000 Green (RoHS& no Sb/Br)
Call TI | POST-PLATE Level-1-NA-UNLIM 0 to 70 ( LM35DH ~ LM35DH)
LM35DM NRND SOIC D 8 95 TBD Call TI Call TI 0 to 100 LM35DM
LM35DM/NOPB ACTIVE SOIC D 8 95 Green (RoHS& no Sb/Br)
CU SN Level-1-260C-UNLIM 0 to 100 LM35DM
LM35DMX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 100 LM35DM
LM35DMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU SN Level-1-260C-UNLIM 0 to 100 LM35DM
LM35DT NRND TO-220 NEB 3 45 TBD Call TI Call TI 0 to 100 LM35DT
PACKAGE OPTION ADDENDUM
www.ti.com 8-Apr-2015
Addendum-Page 2
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish(6)
MSL Peak Temp(3)
Op Temp (°C) Device Marking(4/5)
Samples
LM35DT/NOPB ACTIVE TO-220 NEB 3 45 Green (RoHS& no Sb/Br)
CU SN Level-1-NA-UNLIM 0 to 100 LM35DT
LM35DZ OBSOLETE TO-92 LP 3 TBD Call TI Call TI
LM35DZ/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type LM35DZ
LM35DZ/LFT2 ACTIVE TO-92 LP 3 2000 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type LM35DZ
LM35DZ/LFT4 ACTIVE TO-92 LP 3 2000 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type LM35DZ
LM35DZ/LFT7 ACTIVE TO-92 LP 3 2000 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type LM35DZ
LM35DZ/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS& no Sb/Br)
CU SN N / A for Pkg Type 0 to 100 LM35DZ
LM35H ACTIVE TO NDV 3 1000 TBD Call TI Call TI -55 to 150 ( LM35H ~ LM35H)
LM35H/NOPB ACTIVE TO NDV 3 1000 Green (RoHS& no Sb/Br)
Call TI Level-1-NA-UNLIM -55 to 150 ( LM35H ~ LM35H)
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
PACKAGE OPTION ADDENDUM
www.ti.com 8-Apr-2015
Addendum-Page 3
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuationof the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finishvalue exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
LM35DMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM35DMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 21-Oct-2014
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM35DMX SOIC D 8 2500 367.0 367.0 35.0
LM35DMX/NOPB SOIC D 8 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 21-Oct-2014
Pack Materials-Page 2
MECHANICAL DATA
NDV0003H
www.ti.com
H03H (Rev F)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use ofnon-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products ApplicationsAudio www.ti.com/audio Automotive and Transportation www.ti.com/automotiveAmplifiers amplifier.ti.com Communications and Telecom www.ti.com/communicationsData Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computersDLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-appsDSP dsp.ti.com Energy and Lighting www.ti.com/energyClocks and Timers www.ti.com/clocks Industrial www.ti.com/industrialInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Security www.ti.com/securityPower Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defenseMicrocontrollers microcontroller.ti.com Video and Imaging www.ti.com/videoRFID www.ti-rfid.comOMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.comWireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2015, Texas Instruments Incorporated
