U-Boot 1.1.3 (Dec 15 2009 - 08:33:32)Board: Ralink APSoC DRAM: 32 MBrelocate_code Pointer at: 81fac000flash_protect ON: from 0xBF000000 to 0xBF021167flash_protect ON: from 0xBF030000 to 0xBF030FFF*** Warning - bad CRC, using default environment============================================Ralink UBoot Version: 3.3--------------------------------------------ASIC 3052_MP2 (Port5None)DRAM component: 256 Mbits SDRDRAM bus: 16 bitTotal memory: 32 MBytesFlash component: NOR FlashDate:Dec 15 2009 Time:08:33:32============================================icache: sets:256, ways:4, linesz:32 ,total:32768dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 320 MHZ ####SDRAM bus set to 16 bit SDRAM size =32 MbytesPlease choose the operation: 0: Run bootcmd (default). 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash. 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP.You chose 2 02: System Load Linux Kernel then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Please Input new ones /or Ctrl-C to discard Input device IP (10.10.10.123) ==:192.168.1.1 Input server IP (10.10.10.3) ==:192.168.1.2 Input Linux Kernel filename (netbootstrap_uImage) ==:openwrt.bin netboot_common, argc= 3 NetTxPacket = 0x81FE5400 KSEG1ADDR(NetTxPacket) = 0xA1FE5400 NetLoop,call eth_halt ! NetLoop,call eth_init !Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done Header Payload scatter function is Disable !! ETH_STATE_ACTIVE!!Using Eth0 (10/100-M) deviceTFTP from server 192.168.1.2; our IP address is 192.168.1.1Filename 'openwrt.bin'. TIMEOUT_COUNT=10,Load address: 0x80100000Loading: Got ARP REPLY, set server/gtwy eth addr (08:60:6e:8c:a9:99)Got itT # first block received################################################################ ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################doneBytes transferred = 2752516 (2a0004 hex)NetBootFileXferSize= 002a0004Erase linux kernel block !!From 0xBF050000 To 0xBF2FFFFF b_end =BF7FFFFFErase Flash from 0xbf050000 to 0xbf2fffff in Bank # 1 erase sector = 12sect = 12,s_last = 54,erase poll = 842537 erase sector = 13sect = 13,s_last = 54,erase poll = 867116 erase sector = 14*sect = 14,s_last = 54,erase poll = 851266 erase sector = 15sect = 15,s_last = 54,erase poll = 887773 erase sector = 16*sect = 16,s_last = 54,erase poll = 904649 erase sector = 17sect = 17,s_last = 54,erase poll = 843123 erase sector = 18sect = 18,s_last = 54,erase poll = 832720 erase sector = 19*sect = 19,s_last = 54,erase poll = 845366 erase sector = 20sect = 20,s_last = 54,erase poll = 894500 erase sector = 21*sect = 21,s_last = 54,erase poll = 846607 erase sector = 22sect = 22,s_last = 54,erase poll = 830456 erase sector = 23sect = 23,s_last = 54,erase poll = 841429 erase sector = 24*sect = 24,s_last = 54,erase poll = 840343 erase sector = 25sect = 25,s_last = 54,erase poll = 778857 erase sector = 26*sect = 26,s_last = 54,erase poll = 832340 erase sector = 27sect = 27,s_last = 54,erase poll = 861152 erase sector = 28sect = 28,s_last = 54,erase poll = 851763 erase sector = 29*sect = 29,s_last = 54,erase poll = 845077 erase sector = 30sect = 30,s_last = 54,erase poll = 857608 erase sector = 31*sect = 31,s_last = 54,erase poll = 844269 erase sector = 32sect = 32,s_last = 54,erase poll = 841777 erase sector = 33sect = 33,s_last = 54,erase poll = 842172 erase sector = 34*sect = 34,s_last = 54,erase poll = 834027 erase sector = 35sect = 35,s_last = 54,erase poll = 842524 erase sector = 36*sect = 36,s_last = 54,erase poll = 841240 erase sector = 37sect = 37,s_last = 54,erase poll = 863875 erase sector = 38sect = 38,s_last = 54,erase poll = 839276 erase sector = 39*sect = 39,s_last = 54,erase poll = 846792 erase sector = 40sect = 40,s_last = 54,erase poll = 853312 erase sector = 41*sect = 41,s_last = 54,erase poll = 831404 erase sector = 42sect = 42,s_last = 54,erase poll = 842511 erase sector = 43sect = 43,s_last = 54,erase poll = 845159 erase sector = 44*sect = 44,s_last = 54,erase poll = 880624 erase sector = 45sect = 45,s_last = 54,erase poll = 847981 erase sector = 46*sect = 46,s_last = 54,erase poll = 843653 erase sector = 47sect = 47,s_last = 54,erase poll = 851813 erase sector = 48sect = 48,s_last = 54,erase poll = 863584 erase sector = 49*sect = 49,s_last = 54,erase poll = 875863 erase sector = 50sect = 50,s_last = 54,erase poll = 836819 erase sector = 51*sect = 51,s_last = 54,erase poll = 845545 erase sector = 52sect = 52,s_last = 54,erase poll = 856722 erase sector = 53sect = 53,s_last = 54,erase poll = 851637 erase sector = 54*sect = 54,s_last = 54,erase poll = 858189 doneErased 43 sectors Copy linux image[2752516 byte] to Flash[0xBF050000]....Copy to Flash... Copy 2752516 byte to Flash... addr = 0xBF0B28A4 ,cnt=2348896 addr = 0xBF11514A ,cnt=1945274 addr = 0xBF1779F0 ,cnt=1541652 addr = 0xBF1DA296 ,cnt=1138030 addr = 0xBF23CB3C ,cnt=734408 addr = 0xBF29F3E2 ,cnt=330786 done## Booting image at bf050000 ... Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2013-03-23 19:02:59 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 886961 Bytes = 866.2 kB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OKNo initrd## Transferring control to Linux (at address 80000000) ...## Giving linux memsize in MB, 32Starting kernel ...[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 19:00:46 UTC 2013[ 0.000000] bootconsole [early0] enabled[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)[ 0.000000] Ralink RT3350 id:1 rev:2 running at 320.00 MHz[ 0.000000] Determined physical RAM map:[ 0.000000] memory: 02000000 @ 00000000 (usable)[ 0.000000] Initrd not found or empty - disabling initrd[ 0.000000] Zone PFN ranges:[ 0.000000] Normal 0x00000000 -> 0x00002000[ 0.000000] Movable zone start PFN for each node[ 0.000000] Early memory PFN ranges[ 0.000000] 0: 0x00000000 -> 0x00002000[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128[ 0.000000] Kernel command line: board=WR6202 console=ttyS1,115200 mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),6976k(rootfs),7872k@0x50000(firmware) rootfstype=squashfs,jffs2[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes[ 0.000000] Writing ErrCtl register=0003ad00[ 0.000000] Readback ErrCtl register=0003ad00[ 0.000000] Memory: 29672k/32768k available (2046k kernel code, 3096k reserved, 340k data, 176k init, 0k highmem)[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1[ 0.000000] NR_IRQS:48[ 0.000000] console [ttyS1] enabled, bootconsole disabled[ 0.000000] console [ttyS1] enabled, bootconsole disabled[ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)[ 0.090000] pid_max: default: 32768 minimum: 301[ 0.090000] Mount-cache hash table entries: 512[ 0.100000] NET: Registered protocol family 16[ 0.110000] MIPS: machine is AWB WR6202[ 0.110000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0[ 0.120000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1[ 0.120000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2[ 0.150000] bio: create slab at 0[ 0.160000] Switching to clocksource MIPS[ 0.170000] NET: Registered protocol family 2[ 0.180000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.190000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)[ 0.190000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)[ 0.200000] TCP: Hash tables configured (established 1024 bind 1024)[ 0.210000] TCP reno registered[ 0.210000] UDP hash table entries: 256 (order: 0, 4096 bytes)[ 0.220000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)[ 0.220000] NET: Registered protocol family 1[ 0.270000] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.280000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.290000] msgmni has been set to 57[ 0.300000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)[ 0.300000] io scheduler noop registered[ 0.310000] io scheduler deadline registered (default)[ 0.320000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled[ 0.320000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A[ 0.330000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A[ 0.350000] physmap platform flash device: 00800000 at bf000000[ 0.360000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb[ 0.370000] Amd/Fujitsu Extended Query Table at 0x0040[ 0.380000] Amd/Fujitsu Extended Query version 1.1.[ 0.380000] number of CFI chips: 1[ 0.380000] 6 cmdlinepart partitions found on MTD device physmap-flash.0[ 0.390000] Creating 6 MTD partitions on "physmap-flash.0":[ 0.400000] 0x000000000000-0x000000030000 : "u-boot"[ 0.410000] 0x000000030000-0x000000040000 : "u-boot-env"[ 0.420000] 0x000000040000-0x000000050000 : "factory"[ 0.430000] 0x000000050000-0x000000130000 : "kernel"[ 0.430000] 0x000000130000-0x000000800000 : "rootfs"[ 0.440000] mtd: partition "rootfs" set to be root filesystem[ 0.450000] mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=510000[ 0.460000] 0x0000002f0000-0x000000800000 : "rootfs_data"[ 0.470000] 0x000000050000-0x000000800000 : "firmware"[ 0.490000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout