Page 1

Osbournes LtdLouvre section details& installation details

Louvre models WPL 100 Weather Resistant LouvresWPL 100 Closeable Weather Resistant LouvresWPL 100 Aluminium Vertical LouvresModel WPL 80 Weather Resistant Louvres Model WPL 50 Weather Resistant Louvres EXH 100 Exhaust Louvres EG1 Egg Crate GrilleNV1 No Vision Door & Partition GrillesOL1 / OL1R Wall GrilleSun Louvres Revised August 2005

Page 2

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Head Detail 01

Line of plaster beyond.

Form "V" in plaster to form drip.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Approved waterproof membrane to entireopening and face of blockwork.

Line of jamb angle.

Plastic shims to suit.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Jamb Detail 02

Approved waterproof membrane to entireopening and face of blockwork.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Line of plaster to sill below.

Plastic shims to suit.

Model WPL 50 (Channel Frame)

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

Osbournes WPL 50 (Channel).

Osbournes WPL 50 (Channel).

Model WPL 50 (Channel Frame)

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Concrete blockwork to Engineers design anddocumentation.

Page 3

5mm

min

Approved waterproof membrane to entireopening and face of blockwork.

General Notes:

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Sill Detail 03

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium jamb angle.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Model WPL 50 (Channel Frame)

20 x 3 anodised aluminium flat to face oflouvre, 5mm clear of plaster sill.

Osbournes WPL 50 (Channel).Sikaflex-20AT or similar approved sealantbead.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Page 4

15mm min cover to cladding

15mm drip edge to cladding

Head flashing extends 50mm past flange

150

upsta

nd

5 20mm min cover to joinery

Inseal tape between joinery and flashing.

Typical Fibre Cement/Louvre Head Detail 01 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Timber wall framing with wall insulation as allspecified by Architect.

Trimmer stud.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Typical Fibre Cement/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation as allspecified by Architect.

Purpose made aluminium head flashing with15° slope to extend 150mm behind cladding.Provide 20mm min cover to head of louvre withdrip edge and stop ends.

Sikaflex-20AT or similar approved sealant.

Model WPL 50 (Flanged Frame)

Osbournes Model WPL 50 (Flanged).

Model WPL 50 (Flanged Frame)

uPVC vent strip.

Line of head flashing.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Additional building wrap with 75mm cover tohead flashing.

Osbournes Model WPL 50 (Flanged).

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

45mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to plate with woodscrews @ 300mm c/c.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

5 gap

Page 5

50mm min cover to claddingSloped sill trimmer to suit.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbournes LtdScale 1:5

Typical Fibre Cement/Louvre Sill Detail 03

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Osbournes Model WPL 50 (Flanged).

Model WPL 50 (Flanged Frame)

Aluminium sill flashing with 50mm min cover tocladding. Provide 5°slope to exterior with hem toback edge and 20mm min upstand at both ends.

Timber wall framing with wall insulation asspecified by Architect.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap without seal

Page 6

150

upsta

nd

20mm cover to joinery

5

18mm cover min

1 corrugation min cover

Osbournes Model WPL 50 (Flanged). Line of head & sill flashings.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Timber wall framing with wall insulation as allspecified by Architect.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Jamb Detail 02

Additional building wrap with 75mm cover tohead flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Head trimmer or lintel as required to spanopening.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Line of jamb flashing

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Head Detail 01

Model WPL 50 (Flanged Frame)

Model WPL 50 (Flanged Frame)

Osbournes Model WPL 50 (Flanged).

Inseal tape between joinery and flashing.

Pop rivit flashing to fixing bracket.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Compressible foam.

Preformed jamb flashing.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 7

55

15mm min cover to joinery

50mm min cover to cladding

Osbournes LtdScale 1:5

General Notes:

Typical Vertical Corrugate/Louvre Sill Detail 03

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sloped sill trimmer to suit.Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.Compressible foam.Timber wall framing with wall insulation asspecified by Architect.

Line of jamb flashing.

Model WPL 50 (Flanged Frame)

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Osbournes Model WPL 50 (Flanged).

Provide sill flashing with 5° slope to exterior &hem to back edge and 20mm min upstand at bothends Do not seal to joinery.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 8

150

upsta

nd

5 20mm min cover to joinery

15mm cover to cladding

50mm min

50mm min cover

5

15mm min cover to flashing5

Osbournes LtdScale 1:5

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation as allspecified by Architect.

3108 Inseal tape 12mm thick x 10mm wide.

Line of head flashing.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Timber wall framing with wall insulation as all

specified by Architect.

Typical Horizontal Corrugate/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Typical Horizontal Corrugate/Louvre Head Detail 01Model WPL 50 (Flanged Frame)

Osbournes Model WPL 50 (Flanged).

Model WPL 50 (Flanged Frame)

Inseal tape between joinery and flashing.

uPVC vent strip.

Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 20mmmin cover to head of louvre with drip edge andstop ends.

Preformed jamb flashing.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Line of sill flashing under.

Osbournes Model WPL 50 (Flanged).

Compressible foam.

Close end of flashing and scribe to suit claddingprofile.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Additional building wrap with 75mm cover tohead flashing.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 9

5

5

10mm min cover to flashingSloped sill trimmer to suit.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Line of jamb flashing.

Osbournes LtdScale 1:5

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution NZBC E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Typical Horizontal Corrugate/Louvre Sill Detail 03Model WPL 50 (Flanged Frame)

Osbournes Model WPL 50 (Flanged).

Close end of flashing and scribe to suit claddingprofile. Pop rivit to cladding.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Provide sill flashing with 10°slope to exterior &hem to back edge with 20mm min upstand atboth ends . Provide 25mm cover min to flashing.Flashing to cover at least one corrugation.

40 x 25 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 10

25

varies

25

varies

Osbournes LtdScale 1:5

Typical Precast/Louvre Jamb Detail 02

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.Approved waterproof membrane to entireopening of precast panel.

Sloping sill below.

Precast panel to Engineers design anddocumentation.

Osbournes LtdScale 1:5

Typical Precast/Louvre Head Detail 01

Form drip to panel rebate at head.

Precast panel to Engineers design anddocumentation.

Plastic shims to suit.

Approved waterproof membrane to entireopening of precast panel.

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Osbournes Model WPL 50 (Channel).

Model WPL 50 (Channel Frame)

Model WPL 50 (Channel Frame)

Osbournes Model WPL 50 (Channel).

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Page 11

varies

25

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Osbournes Model WPL 50 (Channel).

General Notes:

Osbournes LtdScale 1:5

Typical Precast/Louvre Sill Detail 03

Plastic shims to suit.

Provide 5° slope to sill.

Precast panel to Engineers design anddocumentation.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations. Provide weepholes insealant at either end of louvre.

Approved waterproof membrane to entireopening of precast panel.

Model WPL 50 (Channel Frame)

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 12

Flanged Frame Channel Frame

Lightweight weather-resistant louvre

NZ7323A

Birdmesh showndashed optional.

Birdmesh showndashed optional.

Scale 1:2

Osbournes Model WPL 50

40-1673

610400

Page 13

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Head Detail 01

Line of plaster beyond.

Form "V" in plaster to form drip.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Approved waterproof membrane to entireopening and face of blockwork.

Line of jamb angle.

Plastic shims to suit.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Jamb Detail 02

Approved waterproof membrane to entireopening and face of blockwork.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Line of plaster to sill below.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

Model WPL 80 (Channel Frame)

Model WPL 80 (Channel Frame)

Osbournes WPL 80 (Channel).

Osbournes WPL 80 (Channel).

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Concrete blockwork to Engineers design anddocumentation.

Page 14

5mm

min

Approved waterproof membrane to entireopening and face of blockwork.

General Notes:

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Sill Detail 03

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium jamb angle.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

30 x 3 anodised aluminium flat to face oflouvre, 5mm clear of plaster sill.

Model WPL 80 (Channel Frame)

Osbournes WPL 80 (Channel).Sikaflex-20AT or similar approved sealantbead.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Page 15

15mm drip edge to cladding

30mm min cover

150

upsta

nd

5

40mm cover to joinery

Head flashing extends 50mm past flange

Typical Fibre Cement/Louvre Head Detail 01 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Timber wall framing with wall insulation as allspecified by Architect.

Trimmer stud.

Line of head flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Typical Fibre Cement/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Additional building wrap with 75mm cover tohead flashing.

uPVC vent strip.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Purpose made aluminium head flashing with15° slope to extend 150mm behind cladding.Provide 40mm min cover to head of louvre withdrip edge and stop ends.

Timber wall framing with wall insulation as allspecified by Architect.

45mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Sikaflex-20AT or similar approved sealant.

Model WPL 80 (Flanged Frame)

Osbournes Model WPL 80 (Flanged).

Osbournes Model WPL 80 (Flanged).

Model WPL 80 (Flanged Frame)

Inseal tape between joinery and flashing.

Line of sill flashing under.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap

Page 16

50mm cover to claddingSloped sill trimmer to suit.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Aluminium sill flashing with 50mm min cover tocladding. Provide 5°slope to exterior with hem toback edge and 20mm min upstand at both ends.

Osbournes LtdScale 1:5

Typical Fibre Cement/Louvre Sill Detail 03

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Osbournes Model WPL 80 (Flanged).

Model WPL 80 (Flanged Frame)

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap without seal

Page 17

1 corrugation min cover

35mm cover min

150

upsta

nd

5

40mm cover to joinery

Line of head & sill flashings.

Compressible foam.

Preformed jamb flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Timber wall framing with wall insulation as allspecified by Architect.

Pop rivit flashing to fixing bracket.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Jamb Detail 02

Additional building wrap with 75mm cover tohead flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Head trimmer or lintel as required to spanopening.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Line of jamb flashing

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Head Detail 01

Inseal tape between joinery and flashing.

Model WPL 80 (Flanged Frame)

Model WPL 80 (Flanged Frame)

Osbournes Model WPL 80 (Flanged).

Osbournes Model WPL 80 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 18

5

30mm min cover to joinery

50mm min cover to cladding

5

Osbournes LtdScale 1:5

General Notes:

Typical Vertical Corrugate/Louvre Sill Detail 03

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sloped sill trimmer to suit.Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.Compressible foam.Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Provide sill flashing with 5° slope to exterior &hem to back edge and 20mm min upstand at bothends Do not seal to joinery.

Line of jamb flashing.

Model WPL 80 (Flanged Frame)

Osbournes Model WPL 80 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 19

5

150

upsta

nd

15mm cover to cladding

40mm min cover to joinery

50mm min cover

5

50mm min

35mm min cover to flashing

5

Osbournes LtdScale 1:5

Additional building wrap with 75mm cover tohead flashing.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

uPVC vent strip.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Timber wall framing with wall insulation as allspecified by Architect.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.Line of head flashing.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Compressible foam.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Preformed jamb flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Close end of flashing and scribe to suit claddingprofile.

Typical Horizontal Corrugate/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Typical Horizontal Corrugate/Louvre Head Detail 01

Osbournes Model WPL 80 (Flanged).

Osbournes Model WPL 80 (Flanged).

Model WPL 80 (Flanged Frame)

Model WPL 80 (Flanged Frame)

Inseal tape between joinery and flashing.40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 20

5

25mm cover to flashing

5

Sloped sill trimmer to suit.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Close end of flashing and scribe to suit claddingprofile. Pop rivit to cladding.

Line of jamb flashing.

Osbournes LtdScale 1:5

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution NZBC E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Typical Horizontal Corrugate/Louvre Sill Detail 03

Provide sill flashing with 10°slope to exterior &hem to back edge with 20mm min upstand atboth ends . Provide 25mm cover min to flashing.Flashing to cover at least one corrugation.

Osbournes Model WPL 80 (Flanged).

Model WPL 80 (Flanged Frame)

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 21

25

varies

25

varies

Osbournes LtdScale 1:5

Typical Precast/Louvre Jamb Detail 02

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.Approved waterproof membrane to entireopening of precast panel.

Sloping sill below.

Precast panel to Engineers design anddocumentation.

Osbournes LtdScale 1:5

Typical Precast/Louvre Head Detail 01

Form drip to panel rebate at head.

Precast panel to Engineers design anddocumentation.

Plastic shims to suit.

Approved waterproof membrane to entireopening of precast panel.

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Osbournes Model WPL 80 (Channel).

Model WPL 80 (Channel Frame)

Model WPL 80 (Channel Frame)

Osbournes Model WPL 80 (Channel).

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 22

varies

25

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

General Notes:

Osbournes LtdScale 1:5

Typical Precast/Louvre Sill Detail 03

Provide 5° slope to sill.Plastic shims to suit.

Precast panel to Engineers design anddocumentation.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Approved waterproof membrane to entireopening of precast panel.

Model WPL 80 (Channel Frame)

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations. Provide weepholes insealant at either end of louvre.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Osbournes Model WPL 80 (Channel).

Page 23

Channel FrameFlanged Frame

Weather-resistant louvreScale 1:2

Birdmesh showndashed optional.

30276

Birdmesh showndashed optional.

J390B

Osbournes Model WPL 80

Page 24

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Head Detail 01Model WPL 100 (Channel Frame)

Line of plaster beyond.

Form "V" in plaster to form drip.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Approved waterproof membrane to entireopening and face of blockwork.

Osbournes WPL 100 (Channel).

Line of jamb angle.

Plastic shims to suit.

Model WPL 100 (Channel Frame)

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Jamb Detail 02

Approved waterproof membrane to entireopening and face of blockwork.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Line of plaster to sill below.Osbournes WPL 100 (Channel).

Plastic shims to suit.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Concrete blockwork to Engineers design anddocumentation.

Page 25

5mm

min

Approved waterproof membrane to entireopening and face of blockwork.

General Notes:

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Sill Detail 03Model WPL 100 (Channel Frame)

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Osbournes WPL 100 (Channel).

Plastic shims to suit.

50 x 50 x 3 anodised aluminium jamb angle.

30 x 3 anodised aluminum flat to face of louvre,5mm clear of plaster sill.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sikaflex-20AT or similar approved sealantbead.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Page 26

15mm drip edge to cladding

150

upsta

nd

5

45mm cover to joinery

Head flashing extends 50mm past flange

35mm min cover to cladding

Typical Fibre Cement/Louvre Head Detail 01Model WPL 100 (Flanged Frame)

Osbournes LtdScale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Timber wall framing with wall insulation as allspecified by Architect.

Trimmer stud.

Line of sill flashing under.

Osbournes Model WPL 100 (Flanged). Line of head flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Typical Fibre Cement/Louvre Jamb Detail 02Model WPL 100 (Flanged Frame)

Osbournes LtdScale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Additional building wrap with 75mm cover tohead flashing.

uPVC vent strip.

Osbournes Model WPL 100 (Flanged).

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation as allspecified by Architect.

45mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Sikaflex-20AT or similar approved sealant.

Inseal tape between joinery and flashing.

Purpose made aluminium head flashing with15° slope to extend 150mm behind cladding.Provide 45mm min cover to head of louvre withdrip edge and stop ends.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap

Page 27

50mm cover to claddingSloped sill trimmer to suit.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Osbournes Model WPL 100 (Flanged).

Aluminium sill flashing with 50mm min cover tocladding. Provide 5°slope to exterior with hem toback edge and 20mm min upstand at both ends.

Osbournes LtdScale 1:5

Typical Fibre Cement/Louvre Sill Detail 03Model WPL 100 (Flanged Frame)

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap without seal

Page 28

1 corrugation min cover

35mm cover min

150

upsta

nd

45mm cover to joinery

5

Line of head & sill flashings.

Compressible foam.

Preformed jamb flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Osbournes Model WPL 100 (Flanged).

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Timber wall framing with wall insulation as allspecified by Architect.

Pop rivit flashing to fixing bracket.

Osbournes LtdScale 1:5

Model WPL 100 (Flanged Frame)Typical Vertical Corrugate/Louvre Jamb Detail 02

Additional building wrap with 75mm cover tohead flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Osbournes Model WPL 100 (Flanged).

Head trimmer or lintel as required to spanopening.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Line of jamb flashing

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbournes LtdScale 1:5

Model WPL 100 (Flanged Frame)Typical Vertical Corrugate/Louvre Head Detail 01

Inseal tape between joinery and flashing.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 29

50mm min cover to cladding

55

35mm min cover to joinery

Osbournes LtdScale 1:5

General Notes:

Model WPL 100 (Flanged Frame)Typical Vertical Corrugate/Louvre Sill Detail 03

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sloped sill trimmer to suit.Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.Compressible foam.Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Provide sill flashing with 5° slope to exterior &hem to back edge and 20mm min upstand at bothends Do not seal to joinery.

Line of jamb flashing.Osbournes Model WPL 100 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 30

15mm cover to cladding

45mm min cover to joinery

150

upsta

nd

5

50mm min

50mm min cover

55

40mm min cover to flashing

Osbournes LtdScale 1:5

Additional building wrap with 75mm cover tohead flashing.

Osbournes Model WPL 100 (Flanged).

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

uPVC vent strip.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Model WPL 100 (Flanged Frame)

Timber wall framing with wall insulation as allspecified by Architect.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Osbournes Model WPL 100 (Flanged). Line of head flashing.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Compressible foam.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Preformed jamb flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Close end of flashing and scribe to suit claddingprofile.

Typical Horizontal Corrugate/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Model WPL 100 (Flanged Frame)

Typical Horizontal Corrugate/Louvre Head Detail 01

Inseal tape between joinery and flashing.

Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 45mmmin cover to head of louvre with drip edge andstop ends.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 31

5

5

25mm cover to flashingSloped sill trimmer to suit.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Close end of flashing and scribe to suit claddingprofile. Pop rivit to cladding.

Osbournes Model WPL 100 (Flanged). Line of jamb flashing.

Osbournes LtdScale 1:5

General Notes:

Model WPL 100 (Flanged Frame)

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution NZBC E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Typical Horizontal Corrugate/Louvre Sill Detail 03

Provide sill flashing with 10°slope to exterior &hem to back edge with 20mm min upstand atboth ends . Provide 25mm cover min to flashing.Flashing to cover at least one corrugation.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 32

25

varies

25

varies

Osbournes LtdScale 1:5

Typical Precast/Louvre Jamb Detail 02Model WPL 100 (Channel Frame)

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.

Osbournes Model WPL 100 (Channel).

Approved waterproof membrane to entireopening of precast panel.

Sloping sill below.

Precast panel to Engineers design anddocumentation.

Osbournes LtdScale 1:5

Typical Precast/Louvre Head Detail 01Model WPL 100 (Channel Frame)

Form drip to panel rebate at head.

Precast panel to Engineers design anddocumentation.

Osbournes Model WPL 100 (Channel).

Plastic shims to suit.

Approved waterproof membrane to entireopening of precast panel.

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 33

varies

25

General Notes:

Osbournes LtdScale 1:5

Typical Precast/Louvre Sill Detail 03Model WPL 100 (Channel Frame)

Provide 5° slope to sill.

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Osbournes Model WPL 100 (Channel).

Plastic shims to suit.

Precast panel to Engineers design anddocumentation.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Approved waterproof membrane to entireopening of precast panel.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations. Provide weepholes insealant at either end of louvre.

Page 34

Channel FrameFlanged Frame

Weather-resistant louvre/double weather stop

Birdmesh showndashed optional.

Birdmesh showndashed optional.

Scale 1:2

Osbournes Model WPL 100

ENZ6656Supplementary mounting

bracket/stiffener

ENZ4894

31723

Page 35

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Head Detail 01

Line of plaster beyond.

Form "V" in plaster to form drip.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Approved waterproof membrane to entireopening and face of blockwork.

Line of jamb angle.

Plastic shims to suit.

Osbournes WPL Vertical 100 (Channel).

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Jamb Detail 02

Approved waterproof membrane to entireopening and face of blockwork.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Line of plaster to sill below.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

Model WPL Vertical 100 (Channel Frame)

Osbournes WPL Verical 100 (Channel).

Model WPL Vertical 100 (Channel Frame)

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Concrete blockwork to Engineers design anddocumentation.

Page 36

5mm

min

Approved waterproof membrane to entireopening and face of blockwork.

General Notes:

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Sill Detail 03

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium jamb angle.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

30 x 3 anodised aluminium flat to face oflouvre, 5mm clear of plaster sill.

Model WPL Vertical 100 (Channel Frame)

Osbournes WPL Vertical 100 (Channel).Sikaflex-20AT or similar approved sealantbead.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Page 37

15mm drip edge to cladding

150

upsta

nd

5

45mm cover to joinery

Head flashing extends 50mm past flange

35mm min cover to cladding

Typical Fibre Cement/Louvre Head Detail 01 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Timber wall framing with wall insulation as allspecified by Architect.

Trimmer stud.

Line of sill flashing under.

Line of head flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Typical Fibre Cement/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Additional building wrap with 75mm cover tohead flashing.

uPVC vent strip.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation as allspecified by Architect.

45mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Sikaflex-20AT or similar approved sealant.

Model WPL Vertical 100 (Flanged Frame)

Osbournes Model WPL Vertical 100 (Flanged).

Model WPL Vertical 100 (Flanged Frame)

Osbournes Model WPL Vertical 100 (Flanged).

Inseal tape between joinery and flashing.

Purpose made aluminium head flashing with15° slope to extend 150mm behind cladding.Provide 45mm min cover to head of louvre withdrip edge and stop ends.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap

Page 38

50mm cover to claddingSloped sill trimmer to suit.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Aluminium sill flashing with 50mm min cover tocladding. Provide 5°slope to exterior with hem toback edge and 20mm min upstand at both ends.

Osbournes LtdScale 1:5

Typical Fibre Cement/Louvre Sill Detail 03

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Model WPL Vertical 100 (Flanged Frame)

Osbournes Model WPL Vertical 100 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap without seal

Page 39

1 corrugation min cover

45mm cover to joinery

150

upsta

nd

35mm cover min

5

Line of head & sill flashings.

Compressible foam.

Preformed jamb flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Timber wall framing with wall insulation as allspecified by Architect.

Pop rivit flashing to fixing bracket.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Jamb Detail 02

Additional building wrap with 75mm cover tohead flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Head trimmer or lintel as required to spanopening.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Line of jamb flashing

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Head Detail 01

Model WPL Vertical 100 (Flanged Frame)

Model WPL Vertical 100 (Flanged Frame)

Osbournes Model WPL Vertical 100 (Flanged).

Osbournes Model WPL Vertical 100 (Flanged).

Inseal tape between joinery and flashing.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 40

5

35mm min cover to joinery

50mm min cover to cladding

5

Osbournes LtdScale 1:5

General Notes:

Typical Vertical Corrugate/Louvre Sill Detail 03

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Model WPL Vertical 100 (Flanged Frame)

Sloped sill trimmer to suit.Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.Compressible foam.Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Provide sill flashing with 5° slope to exterior &hem to back edge and 20mm min upstand at bothends Do not seal to joinery.

Line of jamb flashing.Osbournes Model WPL Vertical 100 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 41

15mm cover to cladding

45mm min cover to joinery

150

upsta

nd

5

50mm min

50mm min cover

55

40mm min cover to flashing

Osbournes LtdScale 1:5

Additional building wrap with 75mm cover tohead flashing.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

uPVC vent strip.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Timber wall framing with wall insulation as allspecified by Architect.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.Line of head flashing.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Compressible foam.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Preformed jamb flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Close end of flashing and scribe to suit claddingprofile.

Typical Horizontal Corrugate/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Typical Horizontal Corrugate/Louvre Head Detail 01Model WPL Vertical 100 (Flanged Frame)

Model WPL Vertical 100 (Flanged Frame)

Osbournes Model WPL Vertical 100 (Flanged).

Osbournes Model WPL Vertical 100 (Flanged).

Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 45mmmin cover to head of louvre with drip edge andstop ends.

Inseal tape between joinery and flashing.40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 42

5

5

25mm cover to flashingSloped sill trimmer to suit.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Close end of flashing and scribe to suit claddingprofile. Pop rivit to cladding.

Line of jamb flashing.

Osbournes LtdScale 1:5

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution NZBC E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Typical Horizontal Corrugate/Louvre Sill Detail 03

Provide sill flashing with 10°slope to exterior &hem to back edge with 20mm min upstand atboth ends . Provide 25mm cover min to flashing.Flashing to cover at least one corrugation.

Osbournes Model WPL Vertical 100 (Flanged).

Model WPL Vertical 100 (Flanged Frame)

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 43

25

varies

25

varies

Model WPL Vertical 100 (Channel Frame)

Osbournes LtdScale 1:5

Typical Precast/Louvre Jamb Detail 02

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.Approved waterproof membrane to entireopening of precast panel.

Sloping sill below.

Precast panel to Engineers design anddocumentation.

Osbournes LtdScale 1:5

Typical Precast/Louvre Head Detail 01

Form drip to panel rebate at head.

Precast panel to Engineers design anddocumentation.

Model WPL Vertical 100 (Channel Frame)

Osbournes Model WPL Vertical 100(Channel).

Osbournes Model WPL Vertical 100(Channel).

Plastic shims to suit.

Approved waterproof membrane to entireopening of precast panel.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 44

varies

25

General Notes:

Osbournes LtdScale 1:5

Typical Precast/Louvre Sill Detail 03

Provide 5° slope to sill.Plastic shims to suit.

Precast panel to Engineers design anddocumentation.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Approved waterproof membrane to entireopening of precast panel.

Model WPL Vertical 100 (Channel Frame)

Osbournes Model WPL Vertical 100(Channel).

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations. Provide weepholes insealant at either end of louvre.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 45

Weather-resistant vertical louvreScale 1:2

Flanged Frame

Channel Frame

9517

Osbournes Model WPL 100 Vertical

31723

Page 46

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Head Detail 01

Line of plaster beyond.

Form "V" in plaster to form drip.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Approved waterproof membrane to entireopening and face of blockwork.

Line of jamb angle.

Plastic shims to suit.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Jamb Detail 02

Approved waterproof membrane to entireopening and face of blockwork.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Line of plaster to sill below.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

Model Exhaust 100 Louvre (Channel Frame)

Model Exhaust 100 Louvre (Channel Frame)

Osbournes Exhaust 100 (Channel).

Osbournes Exhaust 100 (Channel).

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Concrete blockwork to Engineers design anddocumentation.

Page 47

5mm

min

Sikaflex-20AT or similar approved sealantbead.

30 x 3 anodised aluminium flat to face oflouvre, 5mm clear of plaster sill.

Approved waterproof membrane to entireopening and face of blockwork.

General Notes:

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Sill Detail 03

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium jamb angle.

Model Exhaust 100 Louvre (Channel Frame)

Osbournes Exhaust 100 (Channel).

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Page 48

15mm drip edge to cladding

150

upsta

nd

5

45mm cover to joinery

Head flashing extends 50mm past flange

35mm min cover to cladding

Inseal tape between joinery and flashing.

Typical Fibre Cement/Louvre Head Detail 01 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Timber wall framing with wall insulation as allspecified by Architect.

Trimmer stud.

Line of sill flashing under.

Line of head flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Typical Fibre Cement/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Additional building wrap with 75mm cover tohead flashing.

uPVC vent strip.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation as allspecified by Architect.

45mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Sikaflex-20AT or similar approved sealant.

Model Exhaust 100 Louvre (Flanged Frame)

Osbournes Model WPL Exhaust 100 (Flanged).

Osbournes Model WPL Exhaust 100 (Flanged).

Model Exhaust 100 Louvre (Flanged Frame)

Purpose made aluminium head flashing with15° slope to extend 150mm behind cladding.Provide 45mm min cover to head of louvre withdrip edge and stop ends.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap

Page 49

50mm cover to claddingSloped sill trimmer to suit.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Aluminium sill flashing with 50mm min cover tocladding. Provide 5°slope to exterior with hem toback edge and 20mm min upstand at both ends.

Osbornes LtdScale 1:5

Typical Fibre Cement/Louvre Sill Detail 03

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Osbournes Model WPL Exhaust 100 (Flanged).

Model Exhaust 100 Louvre (Flanged Frame)

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap without seal

Page 50

1 corrugation min cover

35mm cover min

150

upsta

nd

45mm cover to joinery

5

Model Exhaust 100 Louvre (Flanged Frame)

Model Exhaust 100 Louvre (Flanged Frame)

Line of head & sill flashings.

Compressible foam.

Preformed jamb flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Timber wall framing with wall insulation as allspecified by Architect.

Pop rivit flashing to fixing bracket.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Jamb Detail 02

Additional building wrap with 75mm cover tohead flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Head trimmer or lintel as required to spanopening.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Line of jamb flashing

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbornes LtdScale 1:5

Typical Vertical Corrugate/Louvre Head Detail 01

Osbournes Model Exhaust 100 (Flanged).

Osbournes Model Exhaust 100 (Flanged).

Inseal tape between joinery and flashing.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 51

50mm min cover to cladding

55

35mm min cover to joinery

Model Exhaust 100 Louvre (Flanged Frame)

Osbournes LtdScale 1:5

General Notes:

Typical Vertical Corrugate/Louvre Sill Detail 03

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sloped sill trimmer to suit.Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.Compressible foam.Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Provide sill flashing with 5° slope to exterior &hem to back edge and 20mm min upstand at bothends Do not seal to joinery.

Line of jamb flashing.Osbournes Model Exhaust 100 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 52

15mm cover to cladding

45mm min cover to joinery

150

upsta

nd

5

50mm min

50mm min cover

55

40mm min cover to flashing

Osbournes LtdScale 1:5

Additional building wrap with 75mm cover tohead flashing.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

uPVC vent strip.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Timber wall framing with wall insulation as allspecified by Architect.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.Line of head flashing.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Compressible foam.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Preformed jamb flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Close end of flashing and scribe to suit claddingprofile.

Typical Horizontal Corrugate/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Typical Horizontal Corrugate/Louvre Head Detail 01Model Exhaust 100 Louvre (Flanged Frame)

Osbournes Model WPL Exhaust 100 (Flanged).

Osbournes Model WPL Exhaust 100 (Flanged).

Model Exhaust 100 Louvre (Flanged Frame)

Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 45mmmin cover to head of louvre with drip edge andstop ends.

Inseal tape between joinery and flashing.40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 53

5

5

25mm cover to flashingSloped sill trimmer to suit.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Close end of flashing and scribe to suit claddingprofile. Pop rivit to cladding.

Line of jamb flashing.

Osbournes LtdScale 1:5

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution NZBC E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Typical Horizontal Corrugate/Louvre Sill Detail 03

Provide sill flashing with 10°slope to exterior &hem to back edge with 20mm min upstand atboth ends . Provide 25mm cover min to flashing.Flashing to cover at least one corrugation.

Model Exhaust 100 Louvre (Flanged Frame)

Osbournes Model WPL Exhaust 100 (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 54

25

varies

25

varies

Osbournes LtdScale 1:5

Typical Precast/Louvre Jamb Detail 02

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.Approved waterproof membrane to entireopening of precast panel.

Sloping sill below.

Precast panel to Engineers design anddocumentation.

Osbournes LtdScale 1:5

Typical Precast/Louvre Head Detail 01

Form drip to panel rebate at head.

Precast panel to Engineers design anddocumentation.

Plastic shims to suit.

Approved waterproof membrane to entireopening of precast panel.

Osbournes Model Exhaust 100 (Channel).

Model Exhaust 100 Louvre (Channel Frame)

Model Exhaust 100 Louvre (Channel Frame)

Osbournes Model Exhaust 100 (Channel).Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 55

varies

25

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

General Notes:

Osbournes LtdScale 1:5

Typical Precast/Louvre Sill Detail 03

Provide 5° slope to sill.Plastic shims to suit.

Precast panel to Engineers design anddocumentation.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Approved waterproof membrane to entireopening of precast panel.

Model Exhaust 100 Louvre (Channel Frame)

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations. Provide weepholes insealant at either end of louvre.

Osbournes Model Exhaust 100 (Channel).

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 56

Channel FrameFlanged Frame

Birdmesh showndashed optional.

Birdmesh showndashed optional.

Weather-resistant louvre

E122

Scale 1:2

Osbournes Exhaust 100 Louvre

31723

Page 57

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Head Detail 01

Line of plaster beyond.

Form "V" in plaster to form drip.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Approved waterproof membrane to entireopening and face of blockwork.

Line of jamb angle.

Plastic shims to suit.

Osbournes LtdScale 1:5

Typical Blockwall/Louvre Jamb Detail 02

Approved waterproof membrane to entireopening and face of blockwork.

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Line of plaster to sill below.

Osbournes WPL Closeable (Channel).

Plastic shims to suit.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

50 x 50 x 3 anodised aluminium angle onsealant bed fixed with suredrives to blockwork.

Osbournes WPL Closeable (Channel).

Model WPL Closeable (Channel Frame)

Model WPL Closeable (Channel Frame)

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atlouvre/angle junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Concrete blockwork to Engineers design anddocumentation.

Page 58

5mm

min

Approved waterproof membrane to entireopening and face of blockwork.

General Notes:

Osbourne-Hume Grilles & Louvres LtdScale 1:5

Typical Blockwall/Louvre Sill Detail 03

Selected plaster finish to exterior of blockworkwith paint finish as selected by Architect.

Plastic shims to suit.

50 x 50 x 3 anodised aluminium jamb angle.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

30 x 3 anodised aluminium flat to face oflouvre, 5mm clear of plaster sill.

Model WPL Closeable (Channel Frame)

Osbourne-Hume WPL Closeable (Channel).Sikaflex-20AT or similar approved sealantbead.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix into blockwork withsuredrive anchors @ 300mm c/c.

Concrete blockwork to Engineers design anddocumentation.

Page 59

15mm drip edge to cladding

150

upsta

nd

5

45mm cover to joinery

Head flashing extends 50mm past flange

35mm min cover to cladding

Typical Fibre Cement/Louvre Head Detail 01 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Timber wall framing with wall insulation as allspecified by Architect.

Trimmer stud.

Line of sill flashing under.

Line of head flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Typical Fibre Cement/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Additional building wrap with 75mm cover tohead flashing.

uPVC vent strip.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation as allspecified by Architect.

45mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Sikaflex-20AT or similar approved sealant.

Model WPL Closeable (Flanged Frame)

Model WPL Closeable (Flanged Frame)

Osbournes Model WPL Closeable (Flanged).

Osbournes Model WPL Closeable (Flanged).

Inseal tape between joinery and flashing.

Purpose made aluminium head flashing with15° slope to extend 150mm behind cladding.Provide 45mm min cover to head of louvre withdrip edge and stop ends.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap

Page 60

50mm cover to claddingSloped sill trimmer to suit.

Selected fibre cement cladding as specified byArchitect on 20mm H3.1 vertical battens to formcavity. Fix in accordance with manufacturersrecommendations.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Aluminium sill flashing with 50mm min cover tocladding. Provide 5°slope to exterior with hem toback edge and 20mm min upstand at both ends.

Osbournes LtdScale 1:5

Typical Fibre Cement/Louvre Sill Detail 03

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Model WPL Closeable (Flanged Frame)

Osbournes Model WPL Closeable (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

5 gap without seal

Page 61

1 corrugation min cover

35mm cover min

45mm cover to joinery

150

upsta

nd

5

Line of head & sill flashings.

Compressible foam.

Preformed jamb flashing.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Timber wall framing with wall insulation as allspecified by Architect.

Pop rivit flashing to fixing bracket.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Jamb Detail 02

Additional building wrap with 75mm cover tohead flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Head trimmer or lintel as required to spanopening.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 40mmmin cover to head of louvre with drip edge andstop ends.

Line of jamb flashing

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Osbournes LtdScale 1:5

Typical Vertical Corrugate/Louvre Head Detail 01

Inseal tape between joinery and flashing.

Model WPL Closeable (Flanged Frame)

Model WPL Closeable (Flanged Frame)

Osbournes Model WPL Closeable (Flanged).

Osbournes Model WPL Closeable (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 62

50mm min cover to cladding

55

35mm min cover to joinery

Osbournes LtdScale 1:5

General Notes:

Typical Vertical Corrugate/Louvre Sill Detail 03

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Sloped sill trimmer to suit.Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.Compressible foam.Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Provide sill flashing with 5° slope to exterior &hem to back edge and 20mm min upstand at bothends Do not seal to joinery.

Line of jamb flashing.

Model WPL Closeable (Flanged Frame)

Osbournes Model WPL Closeable (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 63

15mm cover to cladding

45mm min cover to joinery

150

upsta

nd

5

50mm min

50mm min cover

55

40mm min cover to flashing

Model WPL Closeable (Flanged Frame)

Osbournes LtdScale 1:5

Additional building wrap with 75mm cover tohead flashing.

Head trimmer or lintel as required to spanopening.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

uPVC vent strip.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Timber wall framing with wall insulation as allspecified by Architect.

3108 Inseal tape 12mm thick x 10mm wide.

Line of sill flashing under.Line of head flashing.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

35mm H3.1 treated packer to stop above silltrimmer to allow sill flashing to finish hardagainst trimmer stud.

Compressible foam.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Preformed jamb flashing.

Timber wall framing with wall insulation as allspecified by Architect.

Close end of flashing and scribe to suit claddingprofile.

Typical Horizontal Corrugate/Louvre Jamb Detail 02 Osbournes Ltd

Scale 1:5

Typical Horizontal Corrugate/Louvre Head Detail 01Model WPL Closeable (Flanged Frame)

Osbournes Model WPL Closeable (Flanged).

Osbournes WPL Closeable (Flanged).

Purpose made head flashing with 15° slope toextend 150mm behind cladding. Provide 45mmmin cover to head of louvre with drip edge andstop ends.

Inseal tape between joinery and flashing.40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 64

5

5

25mm cover to flashingSloped sill trimmer to suit.

Building wrap to return into louvre opening.Provide flashing tape over wrap as per WANZwindow installation system.

Timber wall framing with wall insulation asspecified by Architect.

Selected profiled exterior metal sheetcladding on 20mm H3.1 vertical timber battensto Architects specification.

Close end of flashing and scribe to suit claddingprofile. Pop rivit to cladding.

Line of jamb flashing.

Osbournes LtdScale 1:5

General Notes:Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Building wrap must comply with acceptable solution NZBC E2/AS1 & NZS 3604:1999.

Flashing tape must have proven compatibility with the selected building wrap & other materials with which it comes into contact.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Typical Horizontal Corrugate/Louvre Sill Detail 03

Provide sill flashing with 10°slope to exterior &hem to back edge with 20mm min upstand atboth ends . Provide 25mm cover min to flashing.Flashing to cover at least one corrugation.

Model WPL Closeable (Flanged Frame)

Osbournes Model WPL Closeable (Flanged).

40 x 40 x 3 fixing angle pop rivited to back offrame @ 300mm c/c. Fix to platewith wood screws @ 300mm c/c.

Page 65

25

varies

25

varies

Osbournes LtdScale 1:5

Typical Precast/Louvre Jamb Detail 02

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.Approved waterproof membrane to entireopening of precast panel.

Sloping sill below.

Precast panel to Engineers design anddocumentation.

Osbournes LtdScale 1:5

Typical Precast/Louvre Head Detail 01

Form drip to panel rebate at head.

Precast panel to Engineers design anddocumentation.

Plastic shims to suit.

Approved waterproof membrane to entireopening of precast panel.

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Model WPL Closeable (Channel Frame)

Model WPL Closeable (Channel Frame)

Osbournes Model WPL Closeable(Channel).

Osbournes Model WPL Closeable(Channel).

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations.

Page 66

varies25

Osbournes Model WPL Closeable(Channel).

General Notes:

Osbournes LtdScale 1:5

Typical Precast/Louvre Sill Detail 03

Provide 5° slope to sill.

Louvre fixed into precast panel with suredriveanchors @ 400mm c/c.

Plastic shims to suit.

Precast panel to Engineers design anddocumentation.

Flashing materials must be selected based on environmental exposure, refer to NZS 3604:1999.

Refer to the manufacturer or supplier for technical information of all materials.

This is an untested alternative solution to NZBC E2/AS1.

This information is intended to be informative and used as a guideline only. Due to the many variables affecting different projectsOsbournes Ltd can not replace the judgment or advice of an Architect, Engineer or any other relevanttechnical expert and such experts must be consulted to determine the suitability or otherwise of the details or the necessity forfurther design/detailing.

Approved waterproof membrane to entireopening of precast panel.

Model WPL Closeable (Channel Frame)

Sikaflex-20AT or similar approved sealant atlouvre/panel junction on PEF backing rod toratio of 2:1 installed to manufacturersrecommendations. Provide weepholes insealant at either end of louvre.

Sikaflex-20AT or similar approved sealant atpanel/louvre junction to rear of louvre to matchexterior.

Page 67

Weather-resistant fully closable louvreScale 1:2

Closed positionChannel Frame

Osbournes Model WPL 100 Closeable

J805

J806A

9695

Open positionFlanged Frame

31723

Page 68

Scale 1:2

Osbournes Sun LouvreAllows the utilisation of natural light whilst screening and reducing heat transmission.

RHS support frame

Vertical option 2Vertical option 1

ENZ7793

ENZ7792Supplementary mounting

bracket/stiffener

Channel Frame Horizontal Option

Page 69

No vision door & partition grilleScale 1:2

Osbournes Model NV1

ENZ7076

ENZ4431

ENZ4429

Page 70

Scale 1:2Ready made ceiling inspection hatch

ENZ5783

Osbournes Ceiling Hatch

Page 71

Model OL1R Reversibleblade grille 73% free area

Osbournes Model OL1 & OL1RThe Brodie Grille. Ideal for incremental apertures. Sturdily built to hold its shape.

Model OL1Outside louvre

Scale 1:1

ENZ1430

NZ3841

ENZ5783

Page 72

Scale 1:2

Osbournes Model EG1

ENZ5783

Osbournes eggcrate vent