Upload
trandiep
View
215
Download
1
Embed Size (px)
Citation preview
157
LP-Gas EquiPmEnt and accEssoriEs
Completing the hardware needs of an LP-Gas installation is a variety of accessories and tools. Regulators and relief valves often require vents assemblies and vent protectors. Installing a system can require many connection couplings, adaptors with or without screens, filters, swivels, plugs, test blocks, test gauges, tees, and mounting brackets. Also, level gauges and thermometers are required on some installations.
The following Accessory section provides descriptions and selection information for accessories available for regulators and valves. Your local LP-Gas Equipment Distributor can assist you in selecting the proper regulators and accessories for your system.
158
LP-Gas EquiPmEnt and accEssoriEs
RegulatoR accessoRies
pRoduct/function selection infoRmation
tYpical tYpe numBeR
50
Page 165
J500
Page 166
Y602
Page 167
p499
Page 167
p400
Page 168
Test Pressure Gauge for Appliance Line Pressure
1/4-Inch NPT or Female Hose
1/4-Inch MNPT; 0 to 300 psi; Ranges in
MPa, kg/cm2, BarPressure Gauge
Screened Vents for Regulators
Adaptor with Screen
3-Way Tee Blocks
1/4-Inch FNPT to 1-Inch MNPT
1/4-Inch Flare by 1/4-Inch MNPT for Regulators
such as 912 and 67C Series Regulators
POL or 1/4-Inch MNPT
159
LP-Gas EquiPmEnt and accEssoriEs
RegulatoR accessoRies
pRoduct/function selection infoRmation
tYpical tYpe numBeR
p413
Page 168
p100
Page 168
p500
Page 169
p520l
Page 169
Tee Checks for 3-Way POL with Internal Check Disk
Female POL or 1/4-Inch Inverted Flare by Male POL or 1/4-Inch MNPT
Plug and Filter Assembly
Triangular, Bowtie, or Strap Design
Drill Size No. 80 through No. 50
1/4-Inch Inverted Flare
Regulator Mounting Brackets
Adjustable Orifice Reamer
160
LP-Gas EquiPmEnt and accEssoriEs
BulK stoRage tanK and ValVe
accessoRies
pRoduct/function selection infoRmation tYpical tYpe numBeR
J31
Page 170
J400
Page 171
J700
Page 172
m455
Page 172
m270, m536
Page 173
m100, m631
Page 174
m140, m150, m160, m394, m640, m646
Page 175
Rotary Level Gauge for Stational or Mobile Tank
68 to 140-Inch (1727 to 3556 mm)
Lengths
3/4-Inch MNPT for FNPT Connection; with or
without Pressure GaugeLiquid Level Vent Valves
Container (Tank) Thermometer
Liquid Transfer Valve
Male ACMe Adaptor
Female ACMe Filler Couplings
Female ACMe Vapor Return Couplings
1/2-Inch MNPT; -40° to 120°F (-40° to 49°C)
3/4 by 3/4-Inch MNPT
1-1/4 by 1-1/4-Inch through 4-1/4 by 4-1/4-Inch
Male ACMe
1-1/4-Inch Female ACMe by 3/8-Inch MNPT through 4-1/4-Inch Female ACMe
by 3-Inch MNPT
1-1/4-Inch Female ACMe by 3/8-Inch MNPT through 2-1/4-Inch Female ACMe
by 1-1/4-Inch MNPT
161
LP-Gas EquiPmEnt and accEssoriEs
BulK stoRage tanK and ValVe
accessoRies
pRoduct/function selection infoRmation tYpical tYpe numBeR
m498, m529
Page 176
m498, m520
Page 177
t12655t0012 /1H291706562
Page 177
m611
Page 178
m390
Page 178
m301
Page 179
m450a
Page 180
Male ACMe By Female NPT Adaptors
1-1/4 through 4-1/4-Inch Male ACMe by 1/4 through
3-Inch FNPT
1-1/4 through 4-1/4-Inch Male ACMe by 1/2 through
3-Inch FNPT
O-Ring for Male Adaptors
Male ACMe by Male NPT Adaptors
Adaptor Caps
POL Filler Coupling
Single-Piece POL Adaptors
Filler Valve Adaptor
For 2-1/4 or 3-1/4-Inch Adaptors to Give a Better
Seal than Washers
2-1/4 through 4-1/4-Inch Female ACMe by
1-3/4 through 3-1/4-Inch Male ACMe
Soft-Nose Male POL by 1/4-Inch MNPT
Female or Male POL by 1/4 through 3/4-Inch NPT, by 3/8 or 1/2-Inch
SAe Flare
For Filler Valves with 1-3/4-Inch Male ACMe Filler Connection and a 3/4-Inch FNPT Outlet
m570
Page 180
1-3/4-Inch Female ACMe by 1-3/4-Inch Male ACMe
Filler Hose Adaptor with Back Check Valve
162
LP-Gas EquiPmEnt and accEssoriEs
BulK stoRage tanK and ValVe
accessoRies
pRoduct/function selection infoRmation tYpical tYpe numBeR
p104-24, p174
Page 180
m318a
Page 181
m318
Page 182
p306, p193
Page 184
p163a
Page 185
p313
Page 186
p650
Page 187
p314
Page 188
Relief Valve Pipeaway Adaptor for DOT
For Use with Types H282, H5112, H135, H160, H148,
and H173 Valves
With or without Wing Nut; 1/4-Inch MNPT or 9/16-Inch
UNF Left-Hand Thread
Swivel POL Adaptorwith Metal Seats
Soft-Nose POL Adaptor
Air Interlock Systems
Auxiliary Remote Cable Release for Internal Valves
Handle- or Cable-Operated Latch/Remote Release for
Internal Valves
Primary Cable Control for Internal Valves
Cable Control, Release Mechanism, and Cable
Assembly for Internal Valves
Straight or Angle Male POL by 1/4-Inch MNPT
For Bobtail or Transport Trucks
With 25 or 50 Foot (7,6 or 15,2 m) Cable
or without Cable
Built-In Fusible Link to Close Valve in
Case of Fire
4, 5, or 6-Inch (102, 137, or 152 mm)
Travel
For 1-1/4, 2, 3, and 4-Inch (DN 32, 50, 80, and 100)
Internal Valves
163
LP-Gas EquiPmEnt and accEssoriEs
BulK stoRage tanK and ValVe
accessoRies
pRoduct/function selection infoRmation tYpical tYpe numBeR
p613
Page 192
Pneumatic ActuatorFor Types C404-24 and
C414-24 Single Flanged Valve(s)
p539
Page 191
For Closing and Opening of N550 Series Snappy Joe®
emergency Shutoff Valves (eSVs)
Pneumatic Actuator
Pneumatic Actuator
For Types C407, C421, and C427 Valves
(2 and 3-Inch NPT Sizes)p639
Page 192
p623
Page 192
For Types C403-24 andC413-24 Double Flanged Valve(s)
Pneumatic Actuator
Pneumatic Actuator p326
Page 189
For All Fisher® 2 and 3-Inch NPT and 3-Inch
(DN 80) Flanged Internal Valves
p389
Page 189
Pneumatic ActuatorFor Use with
Type C407-10 Only
Pneumatic ActuatorFor Types C404-32 and
C804-32 4-Inch (DN 100) Single Flanged Valve(s)
p614
Page 194
p312
Page 189
Pneumatic Actuator For Type C404-32
Pneumatic ActuatorFor C407-10 Series
1-1/4-Inch NPT Internal Valves
p631
Page 195
164
LP-Gas EquiPmEnt and accEssoriEs
BulK stoRage tanK and ValVe
accessoRies
pRoduct/function selection infoRmation tYpical tYpe numBeR
p120B
Page 197
Spanner Wrench for Large Female ACMe Caps
and Couplings
For Use with 2-1/4through 4-1/4-Inch
ACMe Threads
m3162
Page 196
Swivel or Standard: 1/2-Inch MNPT through
4-1/4-Inch Female ACMe for 1/2 through
3-Inch Hose
Clamp Hose Couplings
Ring and Chain Assemblies
For 1-1/4 through 4-1/4-Inch ACMe Caps
or Dust Sealsp147
Page 198
p206
Page 197
For Types H110 through H732 Valves
Protective Caps for Relief Valves
Seals and Plugs for Female ACMe Threads m178, m239
Page 183
1-1/4 to 4-1/4-Inch Male ACMe, MPOL, or FPOL
m108
Page 183
Female ACMe Caps Hand or Wrench Installation
Fuse Plug
208º to 220ºF (98º to 104ºC) Melting
Temperature Available in 1/8 and 1/4-inch MNPT Sizes
t1140399982/t1033699982
Page 173
p327c, p327d
Page 190
Air CylinderFor N550 Series Snappy Joe®
(eSVs) Close and/or Open Positions
t1139599012
Page 185
For Primary Control (Open or Close the eSV) or an Auxiliary Remote Release (Close only)
4-Way Control Valve
165
LP-Gas EquiPmEnt and accEssoriEs
introduction
50 Series test gauges are used to check appliance line pressure after a regulator has been installed.
Test Gauge Assembly Ordering Information
Type number rAnGe InleT cOnnecTIOn HOse plAsTIc ApprOxImATe weIGHT,
pOunds (kg)
50-20 to 35-inches w.c.
(0 to 87 mbar)
1/4-Inch MNPT No No 1 (0,5)
50P-2Female hose
Yes Yes 2 (0,9)
50P-5 Yes No 1.2 (0,5)
50 series test gauge assemblies
tYpe 50p-5tYpe 50-2
tYpe 50p-2
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
166
LP-Gas EquiPmEnt and accEssoriEs
pressure Gauge Ordering InformationType number cOnnecTIOn lOcATIOn rAnGe
J500
Bottom
0 to 15 psig, 0.1 MPa, 1,0 bar
J501 0 to 30 psig, 0 to 2 kg/cm2
J502 0 to 60 psig, 0.4 MPa, 4,0 bar
J504 0 to 160 psig, 1.1 MPa, 11,0 bar
J505 0 to 300 psig, 2 MPa, 20,0 bar
J510
Back
0 to 15 psig, 0.1 MPa, 1,0 bar
J511 0 to 30 psig, 0.2 MPa, 2,0 bar
J512 0 to 60 psig, 0.4 MPa, 4,0 bar
J514 0 to 160 psig, 1.1 MPa, 11,0 bar
J516 0 to 300 psig, 2.0 MPa, 20,0 bar
J518 0 to 2 kg/cm2, 30 psig
J519 0 to 4 kg/cm2, 60 psig
J531Top
0 to 60 psig, 0.4 MPa, 4,0 bar
J532 0 to 160 psig, 1.1 MPa, 11,0 bar
J537
Back
0 to 30 psig, 0 to 2 kg/cm2
J539 0 to 11 kg/cm2, 160 psig
J541 0 to 60 psig (0 to 27,6 bar) for anhydrous ammonia (NH3) service
J542Bottom
0 to 400 psig (0 to 4,14 bar) (stainless steel) for LP-Gas and
anhydrous ammonia (NH3) service
J551 0 to 30 psig, 0.2 MPa, 2,0 bar
introduction
J500 Series pressure gauges for LP-Gas service are available with either a bottom, back, or top connection. Connection is 1/4-inch MNPT. The back connection makes a more compact assembly on installations where space is limited. Gauges with a top connection also are available. All gauges have a 2-inch (100 mm) diameter face and a steel case.
J500 series pressure gauges
tYpe J501 tYpe J510
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
167
LP-Gas EquiPmEnt and accEssoriEs
introduction
Attached directly to the regulator vent connection to a regulator vent line, vent assemblies should be pointed downward on outdoor installations to avoid moisture build-up in the regulator spring case. Units with a stabilizer assembly are intended for regulators with stability problems. The stabilizer gives a restricted breathing rate under normal conditions, opening for rapid discharge when necessary.
Y602 series Vent assemblies
tYpe Y602-1 (umBRella tYpe) tYpe Y602-13 (angle tYpe)
Vent Assembly Ordering InformationsIze, IncHes sTAbIlIzer umbrellA Type AnGle Type
1/4 FNPTNo - - - - Type Y602-13
Yes - - - - Type Y602-14
Drive fit in 1/4 FNPT No Type Y602-12 - - - -
1/4 MNPT
No Type Y602-1 - - - -
Yes Type Y602-2 - - - -
No Type Y602-11 - - - -
3/8 FNPTNo - - - - Type Y602-5
Yes - - - - Type Y602-6
1/2 FNPT
No - - - - Type Y602-7
Yes - - - - Type Y602-8
No Type Y602-15 - - - -
3/4 FNPT No - - - - Type Y602-9
3/4 MNPTNo - - - - Type Y602-23
No Type Y602-10 - - - -
1 MNPT No - - - - TYpe Y602-25
type p499 adaptor with screen
introduction
Used to convert a 1/4-inch NPT inlet on regulators such as Types 912 and 67C Series to an inverted flare. The Type P499 is available in a 1/4-inch (6,4 mm) inverted flare x 1/4-inch MNPT.
tYpe p499
Adaptor with screen Ordering Information
Type number descrIpTIOn ApprOxImATe weIGHT,pOunds (g)
P499 1/4-inch I.F. x 1/4-inch MNPT adaptor with screen 0.06 (27,2)
ordering guide
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
168
LP-Gas EquiPmEnt and accEssoriEs
types p400, p403, p410, p413, and p414 tee Blocks and checksintroduction
Tee blocks are a 3-way POL connection that allows connection of two containers to a regulator inlet.
Tee checks allow the connection of two containers to a regulator inlet. A check disk inside the Tee check body permits flow only from the container with the highest vapor pressure.
tYpe p400 tee BlocK tYpe p414 tee cHecK
Tee blocks and checks Ordering InformationpIGTAIl Or
pIpInG cOnnecTIOn, IncHes
reGulATOrcOnnecTIOn,
IncHes
Type Of mAnIfOldTee block
(without check) Tee check
Female POL
Female POL P403 - - - -
Male POL P400 P410
1/4 MNPT - - - - P413
1/4 Inverted Flare 1/4 MNPT - - - - P414
introduction
Mounting brackets are used to mount regulators securely to the container or to the side of a building.
mounting brackets Ordering Information
reGulATOr TypesbrAckeT sTyle Type number
Triangular bowtie strap
R622, R632, R642, and R622H P100A P100C - - - -
R122H, R222, and R232 P100A - - - - - - - -
912 P100A - - - - P102A
types p100a, p102a, and p100c mounting Brackets
tYpe p100atYpe p100c
ordering guide
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
169
LP-Gas EquiPmEnt and accEssoriEs
introduction
The Type P500 plug keeps dirt and foreign material from entering change over assemblies like the Type R110. It has a 1/4-inch (6,4 mm) inverted flare. The Type P501 is intended for the inlet of the 67C Series regulators. The Type P501 prevents foreign material from reaching the regulator’s valve disk.
plug and filter Assembly Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (g)
P500 1/4-inch I.F. Male Plug 0.2 (90,7)
P501 1/4-inch NPT inlet filter for Type 67C Series 0.5 (227)
tYpe p500
types p500 and p501 plug and filter assembly
type p520l adjustable orifice Reamer
introduction
The Type P520L tapered reamer is calibrated for propane vapor by drill size. Use Type P520L to enlarge or clean out orifices on LP-Gas appliances ranging from drill size No. 80 to 50.
tYpe p520l
ordering guide
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
Orifice Reamer Ordering InformationType number drIll sIze ApprOxImATe weIGHT, pOunds (g)
P520L No. 80 to 50 0.5 (227)
170
LP-Gas EquiPmEnt and accEssoriEs
introduction
Rotary gauges can be used on stationary or mobile tanks to visually indicate the amount of LP-Gas or Anhydrous ammonia (NH3) in the container. They are also used in filling the tank to the proper liquid level. On mobile applications and some large stationary storage tanks, hangers are recommended to support the horizontal length of the dip tube.
The gauge is operated by opening the small bleed orifice when the tube is in the vapor space of the tank. Moving the pointer on the dial causes the end of the tube to move until it contacts liquid in the container. At that point, discharge from the bleed orifice turns from vapor to liquid and the rotary gauge dial gives the volume percentage of liquid in the tank.
rotary Gauge Ordering Information
lenGTH, IncHes (mm)
lpG dIAl>1200
GAllOn
lpG dIAl≤1200
GAllOn
nH3 dIAl>1200
GAllOn
nO dIAl>1200
GAllOn
68(1,727) J31L-1 J31S-1 J31A-1 J31X-1
69 to 92(1,753 to 2,337) J31L-2 J31S-2 J31A-2 J31X-2
93 to 108 (2,362 to 2,743) J31L-3 J31S-3 J31A-3 J31X-3
109 to 140(2,769 to 3,556) J31L-3L J31S-3L J31A-3L J31X-3L
Dial only P323 P322 P324 - - -
J31 series Rotary gauges
J31 seRies
J31 Series consist of heavy duty gauges that minimize vibration effects (swaying, bouncing) by a long 68-inch (173 cm) stem tube extension. Gauges fit 1-inch (2,54 mm) coupling container connections.
All gauges have stem and dip tubes with an extra large inside diameter. This assures that the correct liquid level can be obtained quickly.
A nylon packing sleeve and a friction ring for the pointer indicator gives smooth rotation and long service life. Steel and stainless steel materials resist rust or corrosion.
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
171
LP-Gas EquiPmEnt and accEssoriEs
liquid level Vent Valves
J415 Series with steel construction are for use on either LP-Gas or Anhydrous ammonia (NH3) service. Installed on large bulk storage tanks at the maximum filling level. Standard valve comes with a 3/4-inch MNPT container connection and two 1/4-inch FNPT side outlets.
Type J415-1 features the addition of a Type J402S liquid level vent valve and Type J542 [0 to 400 psig (0 to 27,6 bar)] pressure gauge installed.
Vent Valves and fixed maximum liquid level gauges
Used in all kinds of LP-Gas containers to give positive visual indication of liquid reaching the maximum allowable liquid level.
Types J402S and J403S do not have dip tubes and must be used in containers where a dip tube has been welded in. Stainless steel constructions are for corrosive service.
J400 series level Vent Valves Ordering InformationType number descrIpTIOn
J402S Stainless steel liquid level vent valve
J403S Stainless steel liquid level vent valve with dial
J408S Stainless steel fixed liquid level vent valve
J409S Stainless steel fixed liquid level vent valve with dial
J415 3/4-inch MNPT angle valve with 1/4-inch FNPT outlets
J415-1 3/4-inch FNPT angle valve with liquid level vent valve and 0 to 400 psig (0 to 27,6 bar) pressure gauge
J415-2 3/4-inch FNPT angle valve with liquid level vent valve and 0 to 300 psig (0 to 20,7) pressure gauge for LP-Gas
J400 series Vent Valves
tYpe J415
tYpe J403stYpe J402s
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
172
LP-Gas EquiPmEnt and accEssoriEs
introduction
Suitable for any tank size in LP-Gas and Anhydrous ammonia (NH3) service, the 2-inch (51 mm) diameter dial reads from –40° to 120°F (–40° to 49°C). They are dustproof and waterproof. Specify Type J700 for a 1/2-inch threaded MNPT by a 4-inch (102 mm) length or Type J701 for a 1/2-inch threaded MNPT by 6-inch (152 mm) length.
container Thermometer block Ordering Information
Type number descrIpTIOn ApprOxImATe weIGHT,pOunds (g)
J700 Thermometer with 4-inch (102 mm) stem0.05 (22,7)
J701 Thermometer with 6-inch (152 mm) stem
J700 series container thermometers
type m455 liquid transfer Valve
introduction
The Type M455 is a special 3/4-inch MNPT inlet by 3/4-inch MNPT outlet valve. It opens the tank’s liquid withdrawal valve the correct distance to permit transfer operations. A nylon gasket is supplied for a tight seal with the withdrawal valve.
liquid Transfer Valve Ordering Information
Type number descrIpTIOn ApprOxImATe weIGHT,pOunds (g)
M455 3/4-inch MNPT x 3/4-inch MNPT for Type N456 inlet 0.3 (136)
tYpe J700
tYpe m455
ordering guide
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
173
LP-Gas EquiPmEnt and accEssoriEs
male acme adaptors
male Acme Adaptor Ordering Information
mAle Acme, IncHes wAsHer drAwInG number
Type number
brass steel
1-1/4 x 1-1/4 1E8122 M270 - - -
1-3/4 X 1-3/4 1E8124 M273 M536-14
2-1/4 X 2-1/4 1E8126 - - - M536-18
3-1/4 X 3-1/4 1E8128 - - - M536-26
4-1/4 X 4-1/4 T10948 - - - M536-34
tYpe m270
ordering guide
introduction
Fuse Plugs, when installed in the actuator piping at the valve, will allow the pneumatic pressure to vent closing the valve if the plug is exposed to temperature above 208° to 220° F (98° to 104° C). Fuse plugs are available in two sizes, 1/8-inch NPT (T1140399982) and 1/4-inch NPT (T1033699982).
fuse plugs
fuse plug Ordering InformationpArT number sIze melTInG TemperATure
T1140399982 1/8-inch NPT208º to 220ºF (98º to 104ºC)
T1033699982 1/4-inch NPT
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
These adaptors are male ACME to male ACME in sizes 1-1/4 by 1-1/4-inch through 4-1/4 by 4-1/4-inch. Brass or steel construction.
174
LP-Gas EquiPmEnt and accEssoriEs
female acme filler couplings
female Acme filler coupling Ordering Information
femAle Acme, IncHes OTHer cOnnecTIOn, IncHes lenGTH, IncHes (mm) fIGure reference
Type number
brass steel
1-1/43/8 MNPT 3 (76,0) 1 M100 - - -
1/2 MNPT 2-1/2 (64,0) 1 M101 - - -
1-3/4
1/2 MNPT 3 (76,0) 1 M110 - - -
3/4 MNPT3 (76,0) 1 M111 M631-6
6-1/8 (156) 2 - - - M635-6
1 MNPT3 (76,0) 1 M112 M631-8
7 (178) 2 - - - M635-8
2-1/4 1-1/4 MNPT 3-1/4 (83,0) 3 M120(1) M121
3-1/41-1/4 FNPT 1-1/2 (38,0) 4 M442 - - -
2 MNPT 3-3/4 (95,0) 3 M130(1) M133
4-1/4 3 MNPT 4-1/2 (114) 3 M664-24 M634-24
1. Steel nipple.
1 2
3 4
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
These couplings allow connection of ACME threads to NPT. One side is 1-1/4 through 4-1/4-inch female ACME. The other side is 3/8 through 3-inch NPT. Available in brass or steel.
175
LP-Gas EquiPmEnt and accEssoriEs
female acme Vapor Return couplings
female Acme Vapor return coupling Ordering InformationfemAle Acme,
IncHes mAle npT, IncHes lenGTH, IncHes (mm) fIGurereference
Type number
brass steel
1-1/43/8
2-1/2 (76,0) 5 M140 - - -
6-1/4 (159) 6 M394 - - -
1/2 2-1/2 (64,0) 5 M141 M640-4
1-3/4
3/43-3/8 (86,0) 5 M150 - - -
7 (178) 6 - - - M646-6
13-1/4 (83,0) 5 M151 M641-8
7-3/8 (187) 6 - - - M646-8
2-1/4 1-1/4 3-3/8 (86,0) 7 M160 - - -
5
6
7
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
Vapor return couplings are available with 1-1/4 through 2-1/4-inch female ACME threads on one side and 3/8 through 1-1/4-inch male NPT threads on the other. Brass or steel construction.
176
LP-Gas EquiPmEnt and accEssoriEs
male Acme by female npT Adaptors Ordering Information
mAle Acme, IncHes femAle npT, IncHes fIGurereference
wAsHer drAwInG number
Type number
brass steel
1-1/4
1/4 9 1E8122 M498-4/2 - - -
3/8 9 1E8122 M498-6/3 - - -
1/2 9 1E8122 M192 - - -
3/4 8 1E8122 M193 - - -
1-3/4
1/4 8 1E8124 M210 - - -
3/8 8 1E8124 M211 - - -
1/2 8 1E8124 M212 - - -
3/4 8 1E8124 M213 M526-6
1 8 1E8124 M214 M526-8
2-1/4
1 9 1E8126 M502-12/8 - - -
1-1/4 9 1E8126 M502-16/10 M522-16/10
1-1/2 9 1E8126 M502-16/12 - - -
3-1/4
1-1/4 8 1E8128 M250 - - -
2 8 1E8128 M252 M528-16
3 8 1E8128 M508-24 M528-24
4-1/4 3 8 T10948 M509-24 M529-24
male acme by female npt adaptors
98
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
These adaptors provide 1-1/4 through 4-1/4-inch male ACME on one side and 1/4 through 3/4-inch female NPT threads on the other side. Brass or steel construction.
177
LP-Gas EquiPmEnt and accEssoriEs
male acme by male npt adaptors
male Acme by male npT Adaptors Ordering Information
mAle Acme, IncHes mAle npT, IncHes wAsHer drAwInG numberType number
brass steel
1-1/4
1/2 1E8122 M498-4/2 - - -
3/4 1E8122 M498-6/3 - - -
1 1E8122 - - - M520-8
1-3/4
1/2 1E8124 - - - M521-4
3/4 1E8124 M215 M521-6
1 1E8124 M216 M521-8
1-1/4 1E8124 M217 M521-10
2-1/4
1-1/4 1E8126 M233 M236
1-1/2 1E8126 M502-12/8 - - -
2 1E8126 M502-16/10 M522-16/10
3-1/42 1E8128 M503-16 M263
3 1E8128 M262 M523-24
4-1/4 3 T10948 M504-24 M524-24
o-Rings for male adaptorsintroduction
The 2-1/4 and 3-1/4-inch male adaptors listed above can be supplied with replacement O-rings instead of the conventional washer type of gasket. In most cases, O-rings give a tighter seal than the washers.
O-ring Ordering InformationO-rInG fOr mATerIAl pArT number
2-1/4-inch adaptors Nitrile (NBR) T12655T0012
3-1/4-inch adaptors Nitrile (NBR) 1H291706562
tYpe m498-4/2
ordering guide
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
Adaptors are 1-1/4-inch through 4-1/4-inch male ACME on one side and 1/2 through 3-inch male NPT on the other. Available in brass or steel.
178
LP-Gas EquiPmEnt and accEssoriEs
adaptor caps
Adaptor cap Ordering Information
femAle Acme, IncHes mAle Acme, IncHesType number
brass ductile Iron
2-1/4 1-3/4 M611 - - -
3-1/4 1-3/4 M612 M622
4-1/4 3-1/4 M613 M623
tYpe m612
type m390 pol filler coupling
pOl filler coupling Ordering InformationreplAcemenT O-rInG mAle pOl mAle npT, IncHes lenGTH, IncHes (mm) Type number
T12945T0012 Soft nose 1/4 6 (152) M390
tYpe m390
ordering guide
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
6-inch (152 mm) male POL to 1/4-inch NPT male filler coupling. Brass construction. Replacement O-rings are available.
introduction
These caps are 2-1/4 through 4-1/4-inch female ACME on one side and 1-3/4 through 3-1/4-inch male ACME on the other. Available in brass or ductile iron.
179
LP-Gas EquiPmEnt and accEssoriEs
m series single-piece pol adaptors
single-piece pOl Adaptor Ordering InformationpOl cOnnecTIOn OTHer cOnnecTIOn, IncHes fIGure reference Type number, brAss
Female POL
1/4 FNPT 1 M301
1/2 FNPT 1 M303
1/4 MNPT 2 M284
3/8 MNPT 2 M285
1/2 MNPT 2 M286
3/4 MNPT 2 M287
Male POL
1/2 FNPT 3 M357
3/8 SAE Flare 4 M353
1/2 SAE Flare 4 M355
1
3
2
4
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
These single-piece brass POL adaptors are available in four styles. Connections are 1/4 through 3/4-inch threaded NPT, 3/8-inch flare, and 1/2-inch NPT flare. Brass construction.
180
LP-Gas EquiPmEnt and accEssoriEs
type m450a filler Valve adaptorintroduction
The Type M450A allows methanol to be added through conventional-design double back check filler valves with a 1-3/4-inch male ACME filler connection and a 3/4-inch FNPT outlet.
filler Hose Adaptor Ordering Information
Type number, brAss
fIller VAlVe cOnnecTIOn,
IncHes
fIller VAlVe cOnnecTIOn,
IncHes
ApprOxImATe weIGHT,
pOunds (kg)
M570 1-3/4 female ACME 1-3/4 male ACME 1.1 (0,5)
type m570 filler Hose adaptor with Back checkintroduction
Intended for the outlet of a bobtail truck filling hose, the Type M570 enables the filling hose to be removed if the filler valve fails to close. An integral back check in the adaptor prevents gas from escaping in the event of a failure of the filler valve. The filler valve should be repaired as soon as possible and the Type M570 removed from the filler valve.
relief Valve pipeaway Adaptor Ordering InformationpIpeAwAy AdApTOr sTyle Type number VAlVe Type
P104-24H282
H5112
P174
H135
H160
H148
H173
types p104-24 and p174 Relief Valve pipeaway adaptorsintroduction
DOT cylinder relief valves must be installed with a pipeaway adaptor to ensure that any discharge is directed away to a safe location.
tYpe m450a
tYpe m570
tYpe p104-24
filler Valve Adaptor Ordering Information
Type number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)
M450A 1 3/4-inch ACME x 3/4-inch NPT adaptor 2.1 (0,95)
ordering guideTo order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies
your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp
181
LP-Gas EquiPmEnt and accEssoriEs
introduction
Three different soft nose (O-ring) POLs with or without a plastic wing nut are available. The wing nut attaches to the POL nut, giving a convenient way of connecting and disconnecting the regulator from the cylinder valve without the bother of a separate wrench.
types m318a, m318aW, and m388 soft-nose pol adaptors
pOl Adaptor Ordering InformationType
number
buIlT-Inexcess-flOw
VAlVe
OuTleT cOnnecTIOn,
IncHeswInG nuT
ApprOxImATe weIGHT,
pOunds (g)M318A
No1/4 MNPT
No 0.3 (136)
M388 No 0.5 (227)
M318AW 9/16 UNF LH Yes 0.3 (136)
Soft nose, replacement O-ring T12945T0012.
tYpe m318aW tYpe m318a
tYpe m388
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
182
LP-Gas EquiPmEnt and accEssoriEs
introduction
POL adaptors with metal seats provide connections between the cylinder valve and the regulator inlet. A wrench is required to generate the required torque to create a metal to metal seal on the POL nose.
types m318, m322, and m345 swivel pol adaptors
swivel pOl Adaptor Ordering Information
Type number pOlcOnnecTIOn
OTHer cOnnecTIOn, IncHes
lenGTH,IncHes (mm)
ApprOxImATe weIGHT, pOunds (g)
M318 Straightmale POL 1/4 MNPT
2-3/8 (60)0.3 (136)
M322 3-1/2 (89)
M345 Angle male POL 1/4 MNPT 3 (76) 0.4 (181)
tYpe m318 tYpe m322
tYpe m345
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
183
LP-Gas EquiPmEnt and accEssoriEs
introduction
ACME caps of various sizes and materials are used on male ACME threads to keep debris out of the piping systems. Small sizes are designed for hand tightening. Larger sizes are intended to be either tightened by hand or with the use of the Type P120B spanner wrench.
m108, m219, m431 series female acme caps
female Acme cap series Ordering Information
femAle Acme sIze, IncHesType number
plastic(1) brass steel
1-1/4 M108 - - - - - - - -
1-3/4 M109 M229(2) M219(2)
2-1/4 - - - - M431 M432
3-1/4 - - - - M441 M443
4-1/4 - - - - M605-34 M625-34
1. For LP-Gas only. 2. Add 1 suffix for Type P147 ring and chain.
tYpe m108 oR m109
tYpe m431
introduction
ACME plugs of various sizes and materials are used in female ACME threads to keep debris out of the piping systems.
seals and plugs
plug and seal Ordering InformationsIze, IncHes pluG dusT seAl
1-1/4 Male ACME - - - - Type M178 Plastic
1-3/4 Male ACME Type M239 Aluminum Type M179 Plastic
2-1/4 Male ACME - - - - Type M180 Plastic
3-1/4 Male ACME - - - - Type M181 Plastic
4-1/4 Male ACME Type M535-34 Steel - - - -
MPOL Type M412 Brass - - - -
FPOL Type M420 Brass - - - -
tYpe m229tYpe m219
tYpe m605-34
tYpe m178 tYpe m239 tYpe m412
ordering guideTo order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies
your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp
184
LP-Gas EquiPmEnt and accEssoriEs
aiR inteRlocK HooK-up on tRanspoRt tRucK
air interlock systemsintroduction
An air interlock system can be configured for transport and bobtail trucks with air brakes by using air cylinder actuated internal valves. This system simultaneously interlocks the internal operation with the truck air brakes without affecting normal air brake operation. It complies with DOT MC331 and NFPA 58
requirements regarding thermal and remote release feasibility.
The air interlock system permits the air brakes to set before the internal valve opens – even if the truck operator forgets to set the brakes. The brakes cannot be released until the internal valve is closed.
Air Interlock system for Transport Trucks Ordering Information
number OfInTernAl VAlVes
IncludesType number4-way Hand Valves
T1007499982fuse plugs
T1033699982Vent screens0l078343062
2-way check ValveT1045699982
backpressure ValveT1045399012
1 2 3 2 1 1 P306
2 4 4 4 1 1 P307
3 5 5 5 1 1 P308
Air Interlock system for bobtail Trucks Ordering Information
Type OfbObTAIl Truck
number OfInTernAl VAlVes
IncludesType number4-way Hand Valves
T1139599012fuse plugs
T11403999822-way check Valve
T1045699982backpressure Valve
T1045399012<3500 gallons (13 249 liters) 1 1 2 1 1 P193
>3500 gallons(13 249 liters) 1 2 3 1 1 P194
Twin Barrel 2 3 3 1 1 P195
In addition, a 4–way actuating valve can be used with Type C404A-32 to pressure both sides of the air cylinder depending upon the position of the operating handle. This allows air pressure to close as well as to open the internal valve.
aiR inteRlocK sYstems foR BoBtail tRucKs
Brakeactuators(part of
brake system)
Relayvalve
Two-waycheck valve
Backpressurevalve Fuse
plugCylinderactuator
Service line
Internalvalve
Fuse plug
Emergency valve(hand valve)
Fuseplug
Four-wayactuating valve
For:
ZM GRAPHICS • 214-906-4162 • [email protected](c) 2007, ZM Graphics Usage: Unlimited within Emerson & Fisher
File name:
Placed file(s):
For page:
Updated by:
GCG, 817-332-4600
Last updated:
Fisher Tank / Emerson
Production notes:
2007 FISHER-TransportTruck.ai
None
Carol Zuber-Mallison09/24/2007
For:
ZM GRAPHICS • 214-906-4162 • [email protected](c) 2007, ZM Graphics Usage: Unlimited within Emerson & Fisher
File name:
Placed file(s):
For page:
Updated by:
GCG, 817-332-4600
Last updated:
Fisher Tank / Emerson
Production notes:
2007 FISHER-BobtailTruck.ai
None
Carol Zuber-Mallison09/24/2007
Brake actuators(part of truck
air brakesystem)
Reservoir(part of truck air brake system)
To Port 1 connectionon actuating valve
Line fromcompressor
(supply)
Brake line(service)
Relayvalve
Two-waycheck valve
Backpressurevalve
Cylinderactuator Internal
valve
Fuse plug
Emergencyvalve
(hand valve)
Four-wayactuating valve
Fuse plug
Fuseplug
185
LP-Gas EquiPmEnt and accEssoriEs
type p163a and p164 series auxiliary Remote Releaseintroduction
Type P163A or P164A Auxiliary Remote Release – These units allow the internal valve to be closed from a location other than the primary control point (Type P650 or P651). Pulling the auxiliary release handle trips the release mechanism on the primary control to close the internal valve.
The two assemblies are identical except for the length. Type P163A has an untrimmed length of 25 feet (7,6 m) and Type P164A has an untrimmed length of 50 feet (15,2 m). Both cables can be trimmed to any length. Both releases can be installed through mounting brackets up to 3/8-inch (9,5 mm) thick.
tYpe p163a
tYpe p164c
ordering guide
t1139599012 4-Way control Valveintroduction
Fisher® makes available a control valve that can be used as primary control (open or close the ESV) or an auxiliary remote release (close only).
Placing the valve’s button in the upward position permits pressure to the cylinder. Pushing the button down exhausts pressure to close all valves connected to the system.
Type P164B — a release assembly that uses 50 ft (15 m) of cable housing which does not require elaborate guiding like uncovered cables.
Type P164C — an Auxiliary Remote Release without cable is also available.
To order any of these products, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
Auxiliary remote release Ordering Information
Type number AuxIlIAry remOTe releAse fOr: lenGTH, feeT (m)
P163A P650 or P651 25 (7,6)
P164A P650 or P651 50 (15)
P164B N550 50 (15)
P164C - - - - No cable
4-way control Valve Ordering InformationType/pArT number TypIcAl use descrIpTIOn
T1139599012Control double-acting cylinder
or two single-acting on a selective basis
4-way push button valve
186
LP-Gas EquiPmEnt and accEssoriEs
tYpe p313
p313 and p340 series latch/Remote Release mechanismsintroduction
With the exception of the 3-inch (DN 80) flanged sizes, all Fisher® brand internal valves can be fitted with a manual latch/remote release mechanism. When the internal valve’s operating lever is manually moved to the open position, the lever can be latched in the open position. The lever can be released from a remote location by pulling on the cable attached to a pull ring, thus closing the internal valve. A built-in fusible element in the latch/release melts if exposed to fire allowing the operating lever to return to the closed position.
Type P313– available factory installed, on the Type C404M32. The Type P315 remote release should be used with this release.
Type P340– easily installed in the field by removing two of the three gland cap screws.
Type P341 – available factory installed on the Type C407M10.
Type P342 – bi-directional latch/remote release allows operation from two directions.
tYpe p340
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
latch/remote release mechnisms Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)
P313 Manual lever and release for C404-32 12 (5,4)
P340 Fuse latch for internal valve 0.3 (0,1)
P341 Latch/Remote release for C407-10 1 (0,5)
P342 Dual latch/remote release for C407-10 1 (0,5)
187
LP-Gas EquiPmEnt and accEssoriEs
p650 series primary cable controlintroduction
Type P650 or P651 Primary Cable Control is capable of actuating all Fisher® internal valves except the 4-inch (DN 100) Type C404-32, the Type P650 or P651 opens and closes the valve from a remote point, usually the rear of the bobtail or transport. Pulling the handle of the primary control opens the internal valve; pushing the handle closes the valve. There are three notches on the primary control that give a travel of 4, 5, or 6-inch (102, 127, or 152 mm) depending upon the travel required by the valve’s operating lever.
tYpe p650
Included with each Type P650 primary control is a 20 feet (6,1 m) cable, Type P134 fusible links, a return spring and mounting hardware. If just the primary cable control is needed, order Type P651, which is available without any of the other accessories.
primary cable control Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)
P650 Cable control assembly for 2 and 3-inch disk valves, 20 feet (6,1 m) 5 (2,27)
P651 Primary cable control only 3 (1,36)
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
188
LP-Gas EquiPmEnt and accEssoriEs
tYpe p315
types p314 cable assembly and p315 auxiliary Remote Release
introduction
Type P314 – This cable assembly is used as an attachment from the Type C404-32 operating lever to the primary cable control. The assembly includes a 40 feet (12,2 m) cable, a special bushing with a fusible element and clamp. The bushing fits in the valve-operating lever and has a built-in fusible element that will melt if exposed to fire, allowing the Type C404-32 to close. The cable connects to the bushing and the clamp permits the other end of the cable to be attached to the fusible link (not furnished) at the primary cable control.
Internal Valve Accessories Ordering InformationInTernAl VAlVe sIze,
IncHes (dn) prImAry cAble cOnTrOl AuxIlIAry remOTe releAse cAble Assembly lATcH/releAse mecHAnIsm
1-1/4, 2, and 3 (32, 50, and 80)(Threaded or Flanged) Type P650 or P651(1) Type P163A or P164A Included with Type P650 Types P341, P342 (Type C407-10),
P340 (C400 Series)
4 (100) Flanged Use Allegheny orWheaten Control Type P315 Type P314 Type P313(2)
1. Type P651 is a primary control only, no accessories. 2. Use with Type P315 remote release mechanism.
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
Type P315 – On manually actuated 4-inch (DN 100) valves (Type C404M32), Type P315 remote handle release can be used to close the internal valve from a remote location. Cable linkage [30 feet (9,1 m)] and mounting hardware are included.
189
LP-Gas EquiPmEnt and accEssoriEs
types p312, p389, and p326 series pneumatic actuatorsintroduction
All Fisher® internal valves can be ordered with an air cylinder that permits the valve to be opened and closed from a remote location. When air pressure is applied to the cylinder, it moves the cylinder’s rod and internal valve operating lever to the open position. Upon loss of air pressure, the valve’s operating lever returns to the closed position. Besides air pressure, nitrogen or carbon dioxide can also be used to pressure the cylinder.
Use of an air cylinder type of actuator permits the opening and closing of the internal valve to be tied into the air brake of the transport or bobtail. Air cylinders can also provide a convenient way to remotely operate a number of internal valves on stationary storage tanks at bulk plants.
Type P389 (1-1/4-Inch Size) – This cylinder can only be used with the Type C407-10 valve. All necessary hardware for installing the cylinder is included.
tYpe p389
Type P326-5 – For Type C403-24 double flanged valves.
Type P326-6 – for Type C401, C407, C421 and C427 valves (2 and 3-inch sizes).
Type 326-7 – for Type C404-24 and C413-24 single flanged valves.
The P326 kits feature a spring return design which eliminates the need for an air return. The “rolled” cylinder diaphragm has a special seal that prevents air leakage and minimizes friction. A bellows covers the cylinder rod to prevent build-up of foreign material around the rod, and a filter in the cylinder vent keeps out dust.
Type P312 (4-Inch Size) – Also available factory installed (C404A32), the cylinder attaches directly to the valve after removal of the cable-operating lever. Included in each assembly is an operating lever and mounting hardware.
pneumatic cylinder Actuators Ordering InformationInTernAl VAlVe Type numbers
pneumATIc cylInder AcTuATOr Type number
mAxImum InleT pressure TO cylInder,psIG (bar)
mAxImum OperATInG pressure TOAcTIVATe InTernAl VAlVe, psIG (bar)
C403-24 P326-5 125 (8,6) 20 (1,4)
C407, C421 and C427 P326-6 125 (8,6) 20 (1,4)
C404-24 P326-7 125 (8,6) 20 (1,4)
C404-32 P312 250 (17,2) 60 (4,1)
C407-10 P389 250 (17,2) 60 (4,1)
tYpe p326
tYpe p312
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
190
LP-Gas EquiPmEnt and accEssoriEs
types p327c and p327d air cylinders introduction
Type P327C—Opening and closing of Snappy Joe® ESVs from a remote location can be done by using Type P327C air cylinder. Depending upon valve inlet pressure, a minimum supply pressure of 30 to 70 psig (2,07 to 4,83 bar) to the cylinder opens the valve. Air, nitrogen, or CO2 can be used for the cylinder supply source. Maximum inlet pressure to the cylinder is 125 psig (8,6 bar). Operating temperature range is -65° to 225°F (-54° to 107°C).
Upon loss of pressure, the valve closed, assisted by the spring in the pneumatic cylinder. All necessary installation hardware for Type P327C is furnished.
Type P327D—Remote pneumatic closure is available with Type P327D release. Depending upon valve inlet pressure, a minimum supply pressure of 30 to 70 psig (2,07 to 4,83 bar) on the Type P327D allows the valve to be latched in the open position with manual closure possible at the valve. Loss of supply pressure to the cylinder permits the ESV to close. Air, nitrogen, or CO2 can be used for the cylinder supply source. Maximum inlet pressure to the cylinder is 125 psig (8,6 bar). Operating temperature range is -40° to 212°F (-40°C to 100°C).
tYpe n550 WitH tYpe p327c
tYpe n550 WitH tYpe p327d
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
Air cylinder Ordering InformationType number descrIpTIOn ApprOxImATe weIGHT, pOunds (kg)
P327C Air cylinder kit for N550 (open and close)1 (0,5)
P327D Air cylinder kit for N550 (close only)
191
LP-Gas EquiPmEnt and accEssoriEs
introduction
Type P539 pneumatic actuator permits opening and closing Fisher® N550 Series Snappy Joe® emergency shutoff valves (ESVs) both at the valve with the use of a pneumatic 4-way valve and from a remote location. The actuator opens the valve when pressure is applied.
Upon loss of pressure, the N550 Series closes, assisted by the spring in the pneumatic actuator.
internal Valve end connection size and style
2 and 3-inch threaded NPT
Actuator pressure limits
Minimum: 20 psig (1,38 bar)Maximum: 100 psig (6,90 bar)Recommended Operating Pressure: 20 to 25 psig (1,38 to 1,72 bar)
Return mechanism
Internal Spring, no air
temperature capabilities
-20° to 150°F (-29° to 66°C)
melt point
212°F (100°C)
approximate Weight
4.8 pounds (2,198 kg)
additional technical data
For more technical information, contact your local LP-Gas and Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp
Figure 1. Type P539 Pneumatic Actuator shown on an N550 Series Emergency Shutoff Valvefeatures
• Provide a Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder
Table 1. construction materials
mOunTInG brAckeT flAT wAsHer And lOck sprInG wAsHer spAcer leVer pusH In fITTInG
304 Stainless steel Carbon plated steel Aluminum 410/416 Stainless steel Brass
type p539 pneumatic actuator
P1136
Figure 2. Dimensions
1/4-incH npt212°f (100°f)fuse plug
1/4-incH mnpt
incHes(mm)
GE31238_C
4.49(114)
5.12(130)
3.71(94,2)
0.79(20,1)
ordering guide
To order this product, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp
192
LP-Gas EquiPmEnt and accEssoriEs
introduction
All Fisher® 2 and 3-inch threaded NPT, 3-inch (DN 80) single and double flanged internal valves can be fitted with an air operated actuator that can be used to open and close the internal valves at the valve or from a remote location. A 3-way valve installed at the valve or at the desired remote location allows air or nitrogen pressure to be applied to the actuator. The pressure supply moves the actuator rod and the internal valve’s operating lever, opening the valve. Upon loss of air pressure, the valve’s operating lever immediately returns to the closed position.
Type 613—For Types C404-24 and C414-24 single flanged valves.
Type P623—For Types C403-24 and C413-24 double flanged valves.
Type P639—For Types C407, C421, and C427 valves (2 and 3-inch threaded NPT sizes).
internal Valve end connection size and style
2 and 3-inch (DN 50 and 80) threaded NPT, single, or double flanged
Actuator pressure limits
Minimum: 20 psig (1,38 bar)Maximum: 125 psig (8,62 bar)Recommended Operating Pressure: 20 to 40 psig (1,38 to 2,76 bar)
Return mechanism
Spring only, no air
thermal Release
1/4-inch threaded NPT fuse plug installed in center port of actuator housing
temperature capabilities
-20° to 150°F (-29° to 66°C)
melt point
212°F (100°C)
approximate Weight
5.6 pounds (2,552 kg)
additional technical data
For more technical information, contact your local LP-Gas Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp
Figure 1. Type P613 Pneumatic Actuator
types p613, p623, and p639 pneumatic actuators
features
• Provide a Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder
Table 1. construction materialsmOunTInG brAckeT lOck sprInG wAsHer cOTTer pIn leVer pusH In fITTInG
304 Stainless steel Zinc plated steel Steel Ductile iron Brass
Figure 2. Type P623 Pneumatic Actuator
Figure 3. Type P639 Pneumatic Actuator
P1131
P1132
P1134
193
LP-Gas EquiPmEnt and accEssoriEs
types p613, p623, and p639 pneumatic actuators
ordering guide
Figure 4. Dimensions
incHes(mm)
GE29523
GE31237
3.15(80,0)
5.79(147)
1/4-incH npt212°f (100°f)fuse plug
1/4 (6,35)tuBing
1/4-incH mnpt
p613 pneumatic actuatoR
5.24(133)
5.63(143)
5.63(143)
1/4 (6,35)tuBing
1/4-incH mnpt
1/4-incH npt212°f (100°f)fuse plug
p623 pneumatic actuatoR
0.79(20,1)
p639 pneumatic actuatoR
GE31236
5.63(143)
3.15(80)
5.63(143)
1/4 (6,35)tuBing
1/4-incH mnpt
1/4-incH npt212°f (100°f)fuse plug
0.79(20,1)
To order, specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
194
LP-Gas EquiPmEnt and accEssoriEs
type p614 pneumatic actuatorintroduction
Type P614 can only be used for Types C404-32 and C804-32 single flanged valves. Fisher® 4-inch (DN 80) single flanged internal valves can be fitted with an air operated actuator that can be used to open and close the internal valves at the valve or from a remote location. A 3-way valve installed at the valve or at the desired remote location allows air or nitrogen pressure to be applied to the actuator. The pressure supply moves the actuator rod and the internal valve’s operating lever, opening the valve. Upon loss of air pressure, the valve’s operating lever immediately returns to the closed position.
internal Valve end connection size and style
4-inch (DN 100) single Flanged
Actuator pressure limits
Minimum: 20 psig (1,38 bar)Maximum: 125 psig (8,62 bar)Recommended Operating Pressure: 20 to 40 psig (1,38 to 2,76 bar)
Return mechanism
Spring only, no air
thermal Release
1/4-inch threaded NPT fuse plug installed in center port of actuator housing
temperature capabilities
-20° to 150°F (-29° to 66°C)
melt point
212°F (100°C)
approximate Weight
9.6 pounds (4,344 kg)
additional technical data
For more technical information, contact your local LP-Gas and Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp
features
• Provide Aa Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder
Figure 1. Type P614 Pneumatic Actuator
Table 1. construction materialsmOunTInG brAckeT lOck sprInG wAsHer rOll pIn leVer pusH In fITTInG
304 Stainless steel Carbon plated steel Carbon plated steel Ductile iron Brass
ordering guide
Figure 2. Dimensions
incHes(mm)
GE31240
6.02(153)
3.15(80)
6.26(159)
1/4 (6,35)tuBing
1/4-incH mnpt
1/4-incH npt212°f (100°f)fuse plug
0.79(20,1)
To order this product, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp
195
LP-Gas EquiPmEnt and accEssoriEs
type p631 pneumatic actuator
introduction
Type P631 Pneumatic Actuator can only be used with C407-10 Series valves, it permits the valve to be opened and closed from a remote location. When air pressure is applied to the cylinder, it moves the cylinder’s rod and internal valve operating lever to the open position. Upon loss of air pressure, the valve’s operating lever returns to the closed position.
internal Valve end connection size and style
1-1/4-inch threaded NPT
Actuator pressure limits
Minimum: 20 psig (1,38 bar)Maximum: 40 psig (2,76 bar)Recommended Operating Pressure: 20 to 25 psig (1,38 to 1,72 bar)
temperature capabilities
-20° to 150°F (-29° to 66°C)
approximate Weight
4.1 pounds (1,842 kg)
additional technical data
For more technical information, contact your local LP-Gas Equipment Distributor or log on to: www.emersonprocess.com/regulators/lp
features
• Can only be used for C407-10 Series Internal Valves• Provide a Convenient Way to Remotely Operate a Number of Internal Valves on Stationary Storage Tanks at Bulk Plants• Besides Air Pressure, Nitrogen or Carbon Dioxide can also be Used to Pressure the Cylinder
Figure 1. Type P631 Pneumatic Actuator
Table 1. construction materialsbrAckeT, bAse,
And cOVerHex HeAd screw,
rOll pInlOck sprInG wAsHer,
JAm Hex nuT leVer And rOd sprInG seAT sprInG cOTTer pIn
304 Stainless steel Carbon plated steel 18-8 Stainless steel 410/416 Stainless steel Aluminum 302 Stainless steel Stainless steel
P1133
ordering guide
Figure 2. Dimensions
2.31(58,7)
5.0(127)
4.02(102)
GE30288
incHes(mm)
To order this product, contact or visit your local LP-Gas Equipment Distributor for availability or log on to: www.emersonprocess.com/regulators/lp
196
LP-Gas EquiPmEnt and accEssoriEs
introduction
M3162 Series Clamp Hose Couplings, for use on LP-Gas or Anhydrous ammonia (NH3), are designed to be compact yet rugged for long, dependable service. A small boss on the clamp portion of the coupling keeps the bolt from turning when installing, making installation much easier. Each ductile iron unit receives a coat of electrodeposition paint. Larger size clamp hose couplings can be furnished with a swivel nut female ACME outlet that reduces weight and space.
m3162 series clamp Hose couplings
clamp and coupling Ordering Information
cOuplInG sTyle sIze, IncHes HOse I.d. , IncHes (mm) ApprOxImATe HOse O.d., IncHes (mm) Type number(1)
Clamp Type, Standard Outlet
1/2 MNPT 1/2 (12,7) 15/16 (23,8) M3162-08
3/4 MNPT 3/4 (19,1) 1-1/4 (31,8) M3162-12
1 MNPT 1 (25,4) 1-1/2 (38,1) M3162-16
1-1/4 MNPT 1-1/4 (31,8) 2 (50,8) M3162-20
1-1/2 MNPT 1-1/2 (18,1) 2-1/4 (23,8) M3162-24
2 MNPT 2 (50,8) 2-3/4 (57,2) M3162-32
3 MNPT 3 (76,2) 3-3/4 (95,3) M3162-48
Clamp Type,Swivel Nut Outlet
1-3/4 Female ACME 3/4 (19,1) 1-1/4 (31,8) M3162-12S(2)
3-1/4 Female ACME 2 (50,8) 2-3/4 (57,2)M3162-32S(2)
M3162-32B(3)
4-1/4 Female ACME 3 (76,2) 3-3/4 (95,3)M3162-48S(2)
M3162-48B(3)
1. Maximum allowable working pressure 350 psig (24,1 bar).2. Has a steel swivel nut with ductile iron nipple.3. Has a brass swivel nut with ductile iron nipple. DO NOT USE WITH ANDHYROUS AMMONIA (NH3).
tYpe m3162-08
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
197
LP-Gas EquiPmEnt and accEssoriEs
type p120B spanner Wrenchintroduction
Used to tighten and loosen large female ACME caps and couplings in the 2-1/4, 3-1/4, and 4-1/4-inch ACME thread sizes.
tYpe p120B
spanner wrench Ordering Information
Type number OVerAll lenGTH,IncHes (mm)
cOnsTrucTIOn mATerIAl
ApprOxImATe weIGHT,pOund (kg)
P120B 18 (457) Aluminium 1 (0,45)
ordering guide
To order, refer to the Ordering Information tables above and specify the type number/s that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp
introduction
Types P206, P297, and P298 protective caps are used to keep moisture and foreign materials from entering the valves. These units are mounted the outside the protective hood on the tank.
types p206, p297, and p298 protective caps for Relief Valves
relief protective cap Ordering InformationVAlVe Type prOTecTIVe cAp Type
H110
P206
H135
H160
H148
H173
H123
H120
H124
H144
H174
H722 P297
H732 P298
tYpe p298
198
LP-Gas EquiPmEnt and accEssoriEs
introduction
Ring and chain assemblies prevent loss of caps and seals. Available for 1-1/4-inch ACME caps or dust seals.
ring and chain Assembly Ordering Information
Type number fOr cAp Or dusT seAlsIze, IncHes fOr fIsHer® brAnd Type
P147 1-1/4 ACME M108 M178
P147(1)
1-3/4 ACMEM109 or M219 - - - -
P148(2) M109 M179
P1482-1/4 ACME
- - - - M180
P167 M431 or M432 - - - -
P1833-1/4 ACME
- - - - M181
P167 M441 or M443 - - - -
P167 4-1/4 ACME M605-34, M625-34M, and M535-34 - - - -
1. Type P147 fits 3/4-inch (19,1 mm) pipe size. 2. Type P148 fits 1-1/4-inch (31,8 mm) pipe size.
p147 oR p148 p167
types p147, p148, and p167 Ring and chain assemblies
ordering guide
To order, refer to the Ordering Information table above and specify the type number that satisfies your requirement. Then, contact or visit your local LP-Gas Equipment Distributor for availability or log on to:
www.emersonprocess.com/regulators/lp