LUXURY CURVED QUADRANT SUPREME

INSTALLATION INSTRUCTIONS

All Supreme shower doors and panels are fully assembled and are reversible for left or right hand fitting, simply turn the door or panel up side down.

The Supreme doors come with the two wall channels pushed onto each side of the door frame. The side panels and inline panels do NOT come with wall channels, you must use one of the channels from the door.

The installation instructions are based on typical use and conditions.

These hints have been prepared for your guidance, you must exercise due care at all times.

It is recommended that 2 people carry out the installation of this enclosure.

Handle glass with care. Although the glass supplied is toughened safety glass (to EN12150), impacts can damage both the glass and the frame.

Warning! Please check for any hidden pipes or cables before drilling holes in the wall.

To stop the drill bit slipping, masking tape can be applied to the tiles when preparing the holes.

When using power tools always follow the manufacturers user instructions.

Do not sit the enclosure on a bed of silicone, as this will also stop any water from draining back into the tray.

DO NOT SEAL THE ENCLOSURE TO THE TRAY ON THE INSIDE

If the enclosure is sealed to the tray on the inside, any water that may get into the framework will not be able to drain back into the tray, this may cause the enclosure to leak.

Leave the silicone sealant to dry for 24 hours before using the enclosure.

Do not use solvents or abrasive materials or chemicals to clean the enclosure.

Only clean using soapy water and a soft cloth, rinse thoroughly afterwards.

Apply more of the supplied lubricant to the inside of the top and bottom tracks (where rollers make contact) when necessary.

Please read these instructions carefully before starting installation and keep in a safe place for future reference.

Check the contents of the pack carefully before installation. Simpsons will not be held responsible for any de-fit / re-fit costs where faulty product has been fitted.

If any fault is found with materials or workmanship, it must be reported immediately to the manufacturer. Remedial action will be taken, based on information received, on condition that: 1. Full details are supplied to the manufacturer; 2. The enclosure has not been modified or tampered with; 3. The manufacturer is informed of any damage/shortages prior to installation.

We do not accept responsibility for any problems that may occur through incorrect installation.

The success of the installation and operation of any shower enclosure is, of course, dependant on the squareness, alignment and construction of the walls to which fixing is to be carried out.

VERY IMPORTANT

You must complete all tiling and grouting, and the shower tray MUST be level and fully sealed to the tiles before installation. If you do not fit the enclosure onto a tiled surface, or seal the tiles to the tray before installation, water may soak into the wall behind the wall channels.

IMPORTANT - Please read before installation

INSTALLATION - Advice and safety

CARE AND CLEANING

1

CURVED QUADRANT

A

B

C

D

Drill, 6.5mm Masonry drill bit, 3mm General drill bit, Phillips screwdriver, Spirit level, Pencil, Scissors, Silicone sealant.

Tools and equipment needed

CONTENTS

10mm Screw x 4

10mm Flat screw x 4

30mm Flat screw x 16

Wall plug x 8

2

E

F

Cover & cap x 4

Plastic clip x 4

G

H

Plastic plug x 12

Top roller x 4

I

J

Bottom roller x 4

Handle x 2

K

L

Magnetic seal x 2

Plastic strip x 2

MWater seal x 4

NWide flap seal x 2

O

PLubricant x 1

Narrow flap seal x 2

Step 1

Fix the top and bottom tracks to the first side profile using 4 x 30mm flat screws (C) as shown. Repeat with the second side profile.

Ensure they are the correct way around, as shown below.

Slide the wall channels fully onto the frame side profiles.

Lift the frame and position on the tray and against the walls. Position the frame so that there is an even gap all the way around between the frame and the edge of the tray.

Note: The frame must not over hang the tray.

Mark the position of the wall channels onto the walls.

LUXURY CURVED QUADRANT

3

Step 2

Step 3

Remove the frame from the tray and remove both wall channels from the frame. Place each wall channel in the marked position on the tray, use a spirit level to ensure they are vertical and mark all 8 fixing holes onto the walls.

Drill holes in the positions marked using a 6.5mm masonry drill bit. Insert wall plugs (D) into all of the holes (beyond the thickness of the tile).

Fix the wall channels to the wall using 8 x 30mm flat screws (C).

Note: Inject silicone sealant into the holes before inserting the screws to seal the holes.

Re-fit the frame into the wall channels.

Step 4

LUXURY CURVED QUADRANT

4

Push fit water seals (M) centrally onto the top and bottom of the side panels. Push fit a narrow flap seals (O) centrally onto the inner edge of the side panels with the flaps on the inside.

Temporarily fit the plastic strips (L) onto the outer edge of the side panels and trim to length. Remove the plastic strips (L) and trim both ends by 10mm (as shown) and refit.

Side panel

- inside face

Side panel

- inside face

Ø 6.5mm

Step 5

Select all 8 top and bottom rollers (H & I) and remove the screws shown (bottom roller shown).

Step 6

Carefully position each side panel inside the enclosure. Insert the plastic strip (L) edge of the panels into the slot in the side profiles. Ensure the side panels fully insert and sit squarlly.

From inside the enclosure, push fit a plastic clip (F) onto the top and bottom corners of the side panels as shown.

Fix the plastic clips to the top and bottom rails using 4 x 10mm screws (A) and push fit the plastic plugs (G).

LUXURY CURVED QUADRANT

5

Fit all of the rollers on to the doors (bottom rollers onto the bottom of the doors etc.) and refit the screws.

Push fit a magnetic seals (K) onto the handle edge of the doors and wide flap seals (N) onto the outer edge (with the flap on the outside) as shown.

Handle side

Door - inside face

Inside

Step 7

a: Inside the enclosure, hang the doors onto the top rail (ensure the magnetic seals are in the middle).

b & c: Push the buttons down on the bottom rollers and position the rollers into the bottom rail and release the buttons.

d: Adjust the doors to hang correctly. Fully tighten the screws shown under the top roller, then slacken off as necessary to level the doors making sure they slide freely and the magnetic seals make contact down their full length.

When the enclosure is fully adjusted, fix the enclosure to the wall channels. From inside, drill 2 holes through each wall channel (120mm down from the top and up from the bottom) into the side profiles

Fit the door handles (J) with the grub screws under the outside handle. First dismantle the handles using the hexagonal key supplied. Attach the inner handle tightening the screws (*) onto the door. Re-attach the outer handle as shown.

Step 8

LUXURY CURVED QUADRANT

6

a. b. c. d.

using a 3mm drill bit. Ensure the holes are at least 10mm in from the edge of the wall channel. Fix using 4 x 10mm flat screws (B) and covers and caps (E), close the covers.

Step 9

Ø 3mm

*

*

Ø 3mm

120mm

10mm

Outside

Step 10

Sealing inside: Run a line of silicone sealant from top to bottom down the joint between the wall channels and tiles, also down the joint where the frame slots into the wall channels.

Do not seal the enclosure to the tray on the inside.

Sealing outside: Run a line of silicone sealant from top to bottom down the joint between the wall channels and tiles. Run a line of silicone sealant 100mm up the joint where the frame slots into the wall channels. Run a line of sealant along the base in the joint between the bottom of the enclosure and the tray, from wall to wall.

LUXURY CURVED QUADRANT

Inside

100 mm

For any further information please contact Simpsons on: 01483 303711

Or visit our web-site at: www.simpsons-enclosures.co.uk

The manufacturer reserves the right to make technical modifications without prior notice.

FINISHING

Apply lubricant (P) to the inside of the top and bottom tracks (where rollers make contact), wipe off any excess.

Step 11