Upload
anonymous-ykdjksq
View
230
Download
0
Embed Size (px)
Citation preview
8/16/2019 Machine Tools Manuals 250214
1/32
LATHE MACHINE
Introduction:-
A lathe is probably the oldest machine tool, stemming from the early
tree lathe, which was turned by a rope passed around the work a few times and attached to
a springly branch over head. The work was supported by two levels struck in adjacent
trees. The operators foot supplied the motion, which was intermittent and fluctuating. The
tool was held in the operations hand. Later a strip of wood called as “Lathe” was used tosupport the rope and hence named as “Lathe”. rom this crode beginning and over period
of more than two centuries, the modern engine lathe has evolved.
Working Principles:-
Lathe removes undesired material from a rotating work piece in the form
of chips with help of tool which is transverse across the work and can be deep in work.
The tool material should be harder than the work piece and lathe held securely and rigidly
on the machine. The tool may be given linear motion in any direction. A lathe is used
principally to produce cylindrical surfaces and planes, at right angles to a!is of rotation. "t
can also produce tapers and bellows etc operation of turning is done on parts as small as
these used by watches to huge parts weighing several tons.
Fig1: Working principle of lt!eFunction#$ The function of a lathe is to remove e!cess material in the form of chips by
rotating the work %iece against a cutting tool to produce cylindrical shapes. The tool
material should be harder than the work piece. The tool may be given liner motion along
work piece in any direction.
&
8/16/2019 Machine Tools Manuals 250214
2/32
Fig": Prts of Center lt!e #c!ine
$i%e &or' specifiction of lt!e:-
&. The height of the centers measured form the lathe bed.
'. The swing diameter over bed.
(. )a!imum job length held between the two centers.
*. The swing diameter over carriage.Prts of Lt!e:-
&. +ase or +ed. '. ead stock. (. Tail stock. *. -arriage. . -ross /lide. 0.-ompound
rest. 1. Apron. 2. Lead /crew. 3. Tool %ost.
Prts (escription:
&. )ed# The bed is a heavy, rugged casting in which are mounted the working parts of the lathe. "t
carries the headstock and tail stock for supporting the workpiece and provides a base for the
movement of carriage assembly which carries the tool.
'. Legs# The legs carry the entire load of machine and are firmly secured to floor by foundation
bolts.
(. Hedstock # The headstock is clamped on the left hand side of the bed and it serves as housing
for the driving pulleys, back gears, headstock spindle, live centre and the feed reverse gear. The
headstock spindle is a hollow cylindrical shaft that provides a drive from the motor to work
holding devices.
*. *er )o+# The 4uick$change gear$bo! is placed below the headstock and contains a number of
different si5ed gears.
Fig,: $c!e#tic digr# of lt!e
(
8/16/2019 Machine Tools Manuals 250214
3/32
. Crrige# The carriage is located between the headstock and tailstock and serves the purpose
of supporting, guiding and feeding the tool against the job during operation. The main parts of
carriage are#
a6 The saddle is an $shaped casting mounted on the top of lathe ways. "t provides support to
cross$slide, compound rest and tool post.
b6 The cross slide is mounted on the top of saddle, and it provides a mounted or automatic crossmovement for the cutting tool.
c6 The compound rest is fitted on the top of cross slide and is used to support the tool post and the
cutting tool.
d6 The tool post is mounted on the compound rest, and it rigidly clamps the cutting tool or tool
holder at the proper height relative to the work centre line.
e6 The apron is fastened to the saddle and it houses the gears, clutches and levers re4uired to
move the carriage or cross slide. The engagement of split nut lever and the automatic feed lever at
the same time is prevented she carriage along the lathe bed.
0. Tilstock # The tailstock is a movable casting located opposite the headstock on the ways of the
bed. The tailstock can slide along the bed to accommodate different lengths of workpiece between
the centers. A tailstock clamp is provided to lock the tailstock at any desired position. The
tailstock spindle has an internal taper to hold the dead centre and the tapered shank tools such as
reamers and drills.
Lt!e opertions:-
/.78. /e4uence of operation -utting tool.
&. acing acing ./././ingle point tool
%lain Turning ./././ingle point tool
/tep9 :nder cut. /ingle point tool ; %arting tool.
Taper Turning. ./././ingle point tool
8/16/2019 Machine Tools Manuals 250214
4/32
d @ small diameter of taper in mm
L @ Length of tapered part in mm.
'@ full taper angle. ? @ half taper angle.
Met!ods of tpers:-
&. /etting over the tail stock centre.
'. +y swiveling the compound rest.
(. +y a taper turning attachment.
*. +y combining longitudinal and cross feed in a special lathe.
. +y forming tool method.
Fig/: Tpes 0f Lt!e 0pertions
C!#fering:- "t is the operation of beveling the e!treme end of the work piece. This is
done to remove burrs, to protect the end of the work piece from being damaged and to
have a better look.
nurling:-
8/16/2019 Machine Tools Manuals 250214
5/32
8/16/2019 Machine Tools Manuals 250214
6/32
*D
E '&
'D'D(D
E &2
E'*
E '.*
All dimensions are in FmmG
. +efore turning the workpiece conical holes must be provided at the ends
and turning may be done with side cutting tool.
$TEP T56NIN*:-
&. Arrange the workpiece between the headstock and tailstock.'. The parting tool can be fi!ed to tool post perpendicular to the workpiece.
(. The machine is started after the workpiece is properly set. Hive the
minimum feed and move the tool up to re4uired length.
*. Iepeat the process for attaining diameter &2mm 9 &*mm.
TAPE6 T56NIN*:-
&. The =$tool is selected for the taper turning and is fi!ed to the tool post.
The cutting edge should be perpendicular to the lathe a!is.
'. /tart with a minimum feed and rotation of compound slide screw which
cause tool to be feed at re4uired taper angles.
(. or every feed measure the smaller dia. >hich should be &2mm increase
the feed and rotate the compound slide screw once again for a good
surface finish.
P6ECA5TI0N$:-
&. /liding parts of lathe should be cleaned and lubricated.
'. /peed selector control shouldnGt be changed when spindle is rotating.
(. -huck should be secured properly.
*. -hips should be cleaned using a brush.
. Hoggles should be used which working on lathe.
6E$5LT:-
The workpiece is step turned, taper turned, threaded 9 knurled as per the
dimensions shown in figure.
$TEP T56NIN*
&&
8/16/2019 Machine Tools Manuals 250214
7/32
*D
E '&
'D'D(D
E &2
E'*
E '.*
All dimensions are in FmmG
TAPE6 T56NIN*
E3P4N0:"
TH6EA( C5TTIN* AN( N56LIN* 0N LATHE MACHINE
AIM: - To perform the following operations on the given work piece using lathe
machine
&. /tep turning
'. Taper turning
(. Thread cutting
*.
8/16/2019 Machine Tools Manuals 250214
8/32
*. /tart the machine with direct speed.
. +efore turning the workpiece conical holes must be provided at the ends
and turning may be done with side cutting tool.
$TEP T56NIN*:-a. Arrange the workpiece between the headstock and tailstock.
b. The parting tool can be fi!ed to tool post perpendicular to the workpiece.
c. The machine is started after the workpiece is properly set. Hive the
minimum feed and move the tool up to re4uired length.
d. Iepeat the process for attaining diameter &2mm 9 &*mm.
TAPE6 T56NIN*:-
a. The =$tool is selected for the taper turning and is fi!ed to the tool post.
The cutting edge should be perpendicular to the lathe a!is.
b. /tart with a minimum feed and rotation of compound slide screw which
cause tool to be feed at re4uired taper angles.
c. or every feed measure the smaller dia. >hich should be &2mm increase
the feed and rotate the compound slide screw once again for a good
surface finish.
TH6EA( C5TTIN*:-
&. -hange the gears and arrange them as per the re4uired pitch. The gears
must be arranged as per the table mentions to respective pitch.
'. 8ne part is selected on the screw and half nut lever is engaged now the
lever moves in the a!is at the workpiece direction.
(. The depth of cut usually varies from D. to 'mm is applied by advancing
the tool perpendicular to the a!is at workpiece.
*. A pitch of *mm say is usually set and pitch gauge is used to check the
correctness of the pitch.
CHAMFE6IN*:-
&. /liding parts, spindles, tools are lubricated sufficiently.
&
8/16/2019 Machine Tools Manuals 250214
9/32
*D
E '&
'D'D(D
E &2
E'*
E '.*
All dimensions are in FmmG
'. The workpiece must be fitted tightly in the chuck and tool advances.
(. The tool is fed and up to the end gets chamfered.
N56LIN*:-
&. or this process, knurling tool is held rigidly on tool post.
'. The rollers are pressed against revolving workpiece to s4ee5e the metal
against the multiple cutting edges producing impossible in a regular
pattern surface with slow speed.
P6ECA5TI0N$:-
0. /liding parts of lathe should be cleaned and lubricated.
1. /peed selector control shouldnGt be changed when spindle is rotating.
2. -huck should be secured properly.
3. -hips should be cleaned using a brush.
&D. Hoggles should be used which working on lathe.
6E$5LT:-
The workpiece is step turned, taper turned, threaded 9 knurled as per the
dimensions shown in figure.
$TEP T56NIN*
&1
8/16/2019 Machine Tools Manuals 250214
10/32
*D
E '&
'D'D(D
E &2
E'*
E '.*
All dimensions are in FmmG
*D
E '&
'D'D(D
E &2
E'*
E '.*
All dimensions are in FmmG
TAPE6 T56NIN*
TH6EA( C5TTIN*
&3
8/16/2019 Machine Tools Manuals 250214
11/32
*D
E '&
'D'D(D
E &2
E'*
E '.*
All dimensions are in FmmG
N56LIN*
4(6ILLIN* MACHINE
Introduction: -
rilling is the process of making cylindrical holes in the work piece. "t is one of the most
important machine tool in the workshop. rilling machine is one of the simplest,
moderate and accurate machine tool. "t consists of a spindle, which imports rotary motion
to the drilling tool. The tool used for drilling holes is called the drill bit. "n this the rotary
motion is given to the tool and the work is stationery. rilling is a process of making a
hole in an object by forcing a rotating tool called drill. The same operation can be
performed in a lathe by holding the drill stationary and rotating work.
'&
8/16/2019 Machine Tools Manuals 250214
12/32
Fig5: RADIAL DRILLING MACHINE
Working principle# The rotating edge of the drill e!erts a large force on the workpiece
and the hole is generated. The removal of metal in a drilling operation is by shearing and
e!trusion.
Fig9: Working principle of drilling #c!ine
Tpes of drilling #c!ines:-&. %ortable drilling m;c.,'. /ensitive drilling m;c. (Hang
drilling m;c. *. Iadial drilling m;c. . Automatic drilling m;c. Btc.6A(IAL (6ILLIN* MACHINE#$ "t is intended for drilling small and large holes on a
heavy work piece. This consists of a heavy round vertical column, mounted on a large
base. The column supports a radial arm which can be raised and lowered to accommodate
work piece of different heights. The arm may be swung around to any position over work
bed. The three movements in radial drilling machines when combined together permit to
be located at any desired point on a large work piece for drilling.
PA6T$ 0F A (6ILLIN* MC.#$ +ase, column, Iadical arm, Blevating screw, rill
head, rill spindle, Table, )otor for elevating the arm, )otor for driving spindle.
&. )se# The base is a heavy casting that supports the machine structureJ it provides rigidmounting for the column and stability for the machine. The base is usually provided with
'(
8/16/2019 Machine Tools Manuals 250214
13/32
holes and slots which help to +olt the base to a table or bench and allow the work$holding
device or the workpiece to be fastened to the base.
'. Colu#n# The column is a vertical post that -olumn holds the worktable and the head
containing the driving mechanism. The column may be of round or bo! section.
(. T;le# The table, either rectangular or round. rill machine;press in shape supports theworkpiece and is carried by the vertical column. The surface of the table is 3D$degree to
the column and it can be raised, lowered and swiveled around it. The table can be
clamp;hold the re4uired the workpiece. /lots are provided in most tables to allow the jigs,
fi!tures or large workpieces to be securely fi!ed directly to the table.
Fig
8/16/2019 Machine Tools Manuals 250214
14/32
a6 -ontact speed motor is mounted at e!treme end of
radial arm.
b6 Train of gearing within the drill head
/.78. /e4uence of operation Tool used
&. )arking =ernier height gauge, /urface plate.
'. %unching ot punch, hammer.
(. %ilot$holed drill rill bit.
*. rilling rill bit.
. Ieaming Ieamer
0. +oring +oring tool.
1. -ounter +oring -ounter bore drill.
2. -ounter /inking -ounter /ink drill
)arking#$ +efore drilling any hole on the given work piece, the center of the hole is
located by drawing two lines at angles to each by means of venire height gauge placed onsurface plate.
%unching#$ After locating a center, identification is made at the point where the hole is to
be drilled. %inching is done by means of center punch and ball peen hammer
%ilot$holed drill# +efore drilling a hole of a larger diameter, a pilot hole of K(mm which
is slightly Hrater then the width of the chisel edge must be drilled. The reason is that the
action of the chisel edge during drilling is more or less an e!trusion process. /o 2D to
2 of total thrust, i.e., vertically upward force will come on chisel edge which increases
the power re4uired and decreases the tool life. This refers to eliminate the thrust acting on
the chisel edge pilot hole is made prior to drilling.
rilling#$ "t is the operation of producing a cylindrical hole by removing metal by therotating edge of a cutting tool called the drill. The drilling is the one of the simplest
methods of producing a hole. rilling does not produce an accurate hole.
Ieaming#$ "t is an aureate away of si5ing and finishing a hole which has been already
drilled. "n order to finish a hole and bring it to the accurate si5e. The hole reamer is made
half that of drilling and used for reaming is known as reamer, which has multiple cutting
edges, reamer can not originate a hole, its simply follows the path, which has been
previously drilled and removes small amount of metal, the materiel removed by this
process is around D.(3mm and for the accurate work, this should not e!ceed D.&'mm.
+oring#$ To enlarge a hole by means of an adjustable cutting tool with only one
cutting edge, this is necessary where suitable si5ed drilled is not available or whole
diameter is so large that it can be ordinary drilled. To finish a hole accurately and to bringit to the re4uired si5e. To machine the internal surface of the hole already producing. To
correct all of roundness of the hole. To correct the location of hole as be boring tool
follows as independent path with respect to the hole.
-ounter +oring#$ The enlarged hole forms a s4uare shoulder with the original hole. This
is necessary is some cases to accommodate the heads of bolts, studs and pins. The tool
used for this is called counter bore. The counter bores are made with straight or tapered
shank to fit in the drills spindle. -ounter boring can give accurately of about K D.DDmm.
The cutting speed for counter boring is ' less than that of drilling operations.
'1
8/16/2019 Machine Tools Manuals 250214
15/32
Fig>: Tpes 0f (rilling 0pertions
-ounter /inking#$ "t is the operation of making a cone shaped enlargement of the end of
a hole to %rovide a recess of a flat head screw or counter sink rivet fillet in the hole. The
Tool used for counter sinking is called counter sink standard counter sinkers have 0D
D ,
2'
D
and 3DD inclined angle that the cutting edges of tool are formed at the conical surface. The
cutting speed in counter sinking is ' less than that of drilling.
rill -hucks#$ A drill chuck is a device intended for holding smaller si5e drills. "t has
two or more adjustable jaws set radially to hold straight shank drills. "t is provided with a
taper shank which is fitted in the tapered hole of the spindle. These are made in
various si5es.
Twist rills#$ "t is an end cutting tool. "t is the most common type of tool used in drilling.
"t consists of a cylindrical piece of steel with special grooves called flutes
TypeGs twist drills# $ &6 %arallel shank twist drill. '6 Taper shank twist drill.
(rills #terils: $ -utting portion$$$$ igh speed steel /hank portion. $$$$-arbon steel.
-utting speed# $ "t is a measure of peripheral speed of the drill in operation e!pressed in
m;min. -utting speed C/6 @ M 7 ; &DDD m;min.
is the diameter of the drill in mm
7 is the r.p.m of the drill spindle.
eed @ the feed of a drill is the distances the drill moves into the work at each
revolution of the spindle. "t is e!pressed in mm; revolution or per min
The feed for min. @ eed per revolution N rpm
epth of cut @ the depth of cut in drilling is e4ual to one half of the drill
diameter.
E3P N0:,&' (6ILLIN* 0PE6ATI0N
AIM: -
To drill a hole on the given workpiece as per dimensions.
T00L$ 6E85I6E(: -
rill bit K &' mm.
MATE6IAL: -
-. ". circular blank.
'3
8/16/2019 Machine Tools Manuals 250214
16/32
E &*mm
E 2Dmm9 'Dmm Thick
P60CE(56E: -
&. The given plate is fi!ed in the machine vice perfectly.
'. 8n the metal plate a point is marked at the central of the plate.
(. The drill feed handle is rotated counter clockwise so that the tool comes down
and make that the tool point coincide with marked point.*. The motor id started and slowly the feed is given to the tool.
. The hole had been done by the tool id checked by making the spindle up and
down.
0. The hole is checked for given dimension.
1. >hile removing plate first switch off the motor and the removed.
2. The hole is slightly higher in dia as the fit.
P6ECA5TI0N$: -
&. The feed must be ade4uate otherwise the drill bit may damage.
'. :se goggles when the operation is going.
(. >hen the operation is going, hold the metal tightly with benchvise jaws.
6E$5LT: -
The hole is drilled on the plate as per given dimensions.
E3P4N0:,&;'
TAPPIN* 0PE6ATI0N
A")# $
To tap the given hole internally and to make threads and e!ternal threads on the rod.
T00L$ 6E85I6E(: -
"nternal tapping tool, B!ternal threading die.
(&
8/16/2019 Machine Tools Manuals 250214
17/32
E &*mm
E 2Dmm
9 'Dmm Thick
MATE6IAL: - -." circular blank
INTE6NAL TH6EA(IN* P60CE(56E: -
&. The tool is inserted in the hole.
'. The tool is turned in the forward direction for same rotation and reversed to
remove the chips that are in minute form.(. The oil is applied mean while for smooth operation.
*. The procedure is repeated until the hole gets threaded cleanly.
E3TE6NAL TH6EA(IN* P60CE(56E: $
&. The e!ternal tapping die is mounted on the rod and oil is applied.
'. The die is rotated until the thread impression occurs on rod and then rotated in
anticlockwise direction to remove the chips.
(. The procedure is repeated until the rod gets fully threaded.
6E$5LT: -
The internal threads and e!ternal threads are produced and the rod is inserted into the
hole.
((
8/16/2019 Machine Tools Manuals 250214
18/32
)&' N p&.1 mm
INTE6NAL TH6EA(IN*
E3TE6NAL TH6EA(IN*
$HAPIN* MACHINE
(
8/16/2019 Machine Tools Manuals 250214
19/32
Introduction:- The shaping machine is used for producing flat surfaces. )achining on
shaper more economical with easier work setting and cheaper tooling. 8n a shaper job is
fi!ed on able and the cuing tool reciprocates across the work piece. The tool cuts on
forward stroke and the return stroke remain idle. As there is no cutti3ng action in return
stroke, we deploy 4uick return mechanism to reduce cutting time. To produce flat
surfaces, channel sections, =$ channels and gear teeths.etc.
Fig 1/:$!ping Mc!ine
Working Principle: The job is rigidly fi!ed on the machine table. The single point
cutting tool held properly in the tool post is mounted on a reciprocating ram. The
reciprocating motion of the ram is obtained by a 4uick return motion mechanism. As theram reciprocates, the tool cuts the material during its forward stroke. uring return, there
is no cutting action and this stroke is called the idle stroke. The forward and return
strokes constitute one operating cycle of the shaper.
Fig1?: Working Principle 0f $!ping Mc!ine
Tpes of #ec!nis#s:- &. -rank shaper# "n construction the crank shaper employs a
crank mechanism to change circular motion of the bull gear to reciprocating motion of the
(1
>ork piece
Tool
8/16/2019 Machine Tools Manuals 250214
20/32
ram. The bull gear receives power either from an individual motor from an over head line
shaft if it is a bell drive shaft.
'. Hear type shaper# this type of shaper carries a rack under it is ram which is driven by a
spur gear. The pinionCspur gear6 machining with the rack is driven by a gear drive. The
speed andthe direction in which the machine traverse depend on the number of gears in
the gear train.
(. ydraulic type# "n these shapers hydraulic pressure is used for driving the ram .it has
become very popular and is also more efficient than the both of the above tool.
Prts of t!e s!per:
&. +ase. '. -olumn (. -ross slide *, saddle . Table 0. -lapper bo! 1.
Iam 2. Tool head. 3. eed disc. Blevating screw. etc
Construction# The main parts of the /haper machine is +ase, +ody C%illar, rame, -olumn6,
-ross rail, Iam and tool head CTool %ost, Tool /lide, -lamper +o! +lock6.
)se# The base is a heavy cast iron casting which is fi!ed to the shop floor. "t supports the body
frame and the entire load of the machine. The base absorbs and withstands vibrations and other
forces which are likely to be induced during the shaping operations.
)od &Pillr7 Fr#e7 Colu#n': "t is mounted on the base and houses the drive mechanism
compressing the main drives, the gear bo! and the 4uick return mechanism for the ram
movement. The top of the body provides guide ways for the ram and its front provides the guide
ways for the cross rail.
Cross ril: The cross rail is mounted on the front of the body frame and can be moved up and
down. The vertical movement of the cross rail permits jobs of different heights to be
accommodated below the tool. /liding along the cross rail is a saddle which carries the work table.
6# nd tool !ed: The ram is driven back and forth in its slides by the slotted link mechanism.
The back and forth movement of ram is called stroke and it can be adjusted according to the
length of the workpiece to be$machined.
Fig19: Prts 0f A $!per
(3
8/16/2019 Machine Tools Manuals 250214
21/32
Cutting sped:- "n a shaper the cutting action is intermittent and is considered only during
the forward cutting stroke.
Length of cutting stroke.
-utting sped#$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
Time re4uired by the cutting stroke.
Feed:- "t is the relative movement of the tool or work in a direction perpendicular tothe a!is of reciprocation of the ram for double stroke. "n is e!pressed in
mm. The feed is always
given at the end of return stroke when the tool is not cutting the metal.
(ept! of cut:- "t is the thickness of metal that is removed in one cut. "t is the
perpendicular distances measured between machined surface and non
machined surface of the work piece.
$pecifictions:&. )a!imum length of the stroke of ram
'. -utting to return stroke ratio.
(. 7o and amount of feed
*. Type of speed reduction.. Type of drive and 4uick mechanism
BN%.78#*
*&
8/16/2019 Machine Tools Manuals 250214
22/32
MAIN* 0F FLAT $56FACE 0N $HAPIN* MACHINE
AIM: -
To generate flat surface according to the given dimensions by using shaping
machine.T00L$ 6E85I6E(: -
&. =$tool,
'. scriber,
(. steel rule and
*. center punch.
MATE6IAL 6E85I6E(: -
-." s4uare bar
P60CE(56E:-
&. )easure the dimensions of a given mild steel block.
'. i! the block in the shape vice and tight it fully.
(. +y providing a depth of cut of say D.* for rough finish and D.'mm for finish
remove the e!cess material on block by a .-.- tool until the re4uired
dimensions are obtained.
*. Apply chalk on the face of the block and mark the dimensions as shown in
figure.
. %unching is done by pilot punch along the marking lines.
0. Adjust the tip of tool such that it touches the metal piece and by providing
re4uired depth of cut, the machine is started.
1. /hape the material by increasing the feed and depth of cut
%IB-A:T"87/#$
-heck the tool not to cross the face of the material.
&. /lowly increase the feed of tool.
'. -heck dimensions for every stroke.
(. /et the workpiece e!actly below the tool before starting the machine.
6E$5LT:- /haping operation is performed for the given workpiece.
*(
8/16/2019 Machine Tools Manuals 250214
23/32
'
$L0TTIN* MACHINE
*
ALL ")B7/"87/ AIB "7 mm
8/16/2019 Machine Tools Manuals 250214
24/32
Introduction: The slotting machine is a reciprocating machine tool in which, the ram
holding the tool reciprocates in a vertical a!is and the cutting action of the tool is only
during the downward stroke.
Construction# The slotter can be considered as a vertical shaper and its main parts are:
&. +ase, column and table
'. Iam and tool head assembly
(. /addle and cross slide
*. Iam drive mechanism and feed mechanism.
The base of the slotting machine is rigidly built to take up all the cutting forces. The frontface of the vertical column has guide ways for Tool the reciprocating ram. The ram
supports the tool head to which the tool is attached. The workpiece is mounted on the
table which can be given longitudinal, cross and rotary feed motion.
The slotting machine is used for cutting grooves, keys and slotes of various shapes
making regular and irregular surfaces both internal and e!ternal cutting internal and
e!ternal gears and profiles The slotter machine can be used on any type of work where
vertical tool movement is considered essential and advantageous.
The different types of slotting machines are#
&. Punc! slotter# a heavy duty rigid machine designed for removing large amount of
metal from large forgings or castings
'. Tool roo# slotter# a heavy machine which is designed to operate at high speeds. This
machine takes light cuts and gives accurate finishing.
(. Production slotter# a heavy duty slotter consisting of heavy cast base and heavy
frame, and is generally made in two parts.
E3P4N0:?
*1
8/16/2019 Machine Tools Manuals 250214
25/32
$L0TTIN* 0PE6ATI0N
AIM: -
To cut a keyway on given circular blank according to the given dimensions by
using slotting machine.
T00L$ 6E85I6E(: -
&. /lotter
'. scriber,
(. steel rule
*. center punch.
MATE6IAL 6E85I6E(: -
-." circular blank of dimensions C2D "A ! 'D T"-
8/16/2019 Machine Tools Manuals 250214
26/32
E 2Dmm9 'Dmm Thick
AO0 N * mm
*. 7ever attempt to remove chips or reach across the table while the ram is in
motion.
6E$5LT: -
The re4uired groove is obtained on mild steel plate according to given dimensions.
&
8/16/2019 Machine Tools Manuals 250214
27/32
MILLIN* MACHINE
Introduction:- )illing is a machining process in which metal is removed by rotating
multi$edge cutting tool called “milling cutter”, while the work piece fed against to it. A
milling machine is a machine tool that removes metal chips. >ork is fed against a
rotation multipoint cutter. "t removes metal at a very fast rate. The job movement is
hori5ontal, vertical and cross feeding.
GENERAL MILLING MACHINES
A milling machine is a machine tool that removes metal as the work is fed against a
rotating multipoint cutter. The cutter rotates at a high speed and because of the multiple
cutting edges it removes metal at a very fast rate. The machine can also hold one or more
no of cutters at a time. This is why a milling machine finds wide application in production
work. This is superior to other machine as regards accuracy and better surface finish and
is designed for machining a variety of tool room work.
Fig @ : nee And Colu#n Tpe Milling Mc!ine
Principle:-The milling machine mechanism is composed of spindle drive mechanism and
the table feed mechanism. The spindle drive mechanism is incorporated in the column.
All modern machines are driven by individual motors housed within the column, the
spindle receives power from a combination of gears and clutch assembly. )ultiple speedof the spindle may be obtained by attaining the gear ratio.
Fig1:Working principle of #illing #c!ine
(
8/16/2019 Machine Tools Manuals 250214
28/32
PA6T$ (E$C6IPTI0N:%arts of milling m;c#$
&.+ase. '. -olumn. (.
8/16/2019 Machine Tools Manuals 250214
29/32
0. 0=er rm# The 8ver arm is mounted at the top of the column and is guided in perfect
alignment by the machined surfaces. The 8ver arm is the support for the arbor.
1. Ar;or support# The arbor support is fitted to the 8ver arm and can be clamped at any location
on the 8ver arm. "ts function is to align and support various arbors. The arbor is a machined shaft
that holds and drives the cutters.
2. Ele=ting screB# The upward and downward movement to the knee and the table is given bythe elevating screw that is operated by hand or an automatic feed.
Types of milling m;c.#$ -olumn and knee type.
&. ori5ontal milling. '. =ertical milling. (. :niversal milling.
*. 8mniversal milling.
)illing m;c. mechanism#$
The spindle drive mechanism is incorporated in the column. All modern machines aredriven by individual motors housed within the column, and the spindle reeves power from
a combination of gears and clutch assembly. )ultiple speeds of the spindly may be
obtained by altering the gear ratio.
>ork holding devices#$ T$ bolts and clamps, =$blocks, Angle plate, =ices, etc.
-utter holding devices#$ Arbors, collets, Adapters, /pring collets, +olted cutters, /crew
C a 6 :p milling # The up milling which is also called conventional milling, is the process
of removing the metal by a cutter which is rotated against the direction of travel of thework piece.
C b 6 own milling # The down milling which is also called climb milling, is the process
of removing the metal by a cutter which is rotated in the same the direction of travel of
the work piece.
-utting speed#$ The cutting speed of a milling cutter is its peripheral linear speed
resulting from rotation. "t is e!pressed in meters per minute. The cutting speed can be
derived formula.
=@ M d n ; &DDD minutes per min.
=@ the cutting speed in inch per min.
d@ the diameter of the cutter in mm.
n@ the cutter speed in rpm.
eed#$ The feed in a milling machine is defined as the rate with which the work piece
Advances under the cutter.
epth of cut#$ The depth of cut in milling is the thickness of the material moved in one
pass of the work under the cutter.
1
8/16/2019 Machine Tools Manuals 250214
30/32
E3P4N0:9
*EA6 C5TTIN* 0N MILLIN* MACHINE
AIM:-
To cut a spur gear on a given wooden specimen.MATE6IAL:- -ircular wooden specimen.
T00L$ 6E85I6E( :-
&. Hear tooth vernier
'. )illing cutter
(. /teel rule
P60CE(56E:-
&. The given workpiece is checked for dimensions.
'. rom the calculations no. of holes and no. of hole circles are known.
(. The workpiece is set in the machine correctly.
*. 7umber of holes and no. of hole circles are set on the inde! plate of the dividing
head.
. The cutter is first made to touch the workpiece and then the feed of mm is given.
0. After cutting one teeth the feed removed to cut ne!t teeth, the inde! circle is
rotated for one revolution as per remained number of tools.
1. the process is repeated, the remained number of teeth are cut.
P6ECA5TI0N$:
&. -heck the straightness of the a!is of work piece within the live centre of the
dividing head
'. should be careful while performing the inde!ing
6E$5LT:
Hear cutting on milling machine is performed successfully.
3
8/16/2019 Machine Tools Manuals 250214
31/32
2D
'D
'D
0&
8/16/2019 Machine Tools Manuals 250214
32/32