Embed Size (px)
Citation preview
is featured in our new lineup of standard seismic cable restraint systems. Sure to be a contractor favorite, the QuakeLoc™ connector quickly and easily fastens cables used in the seismic restraint of piping, duct, electrical cable trays, and suspended equipment. QuakeLoc™ is proudly made in the USA.
Seismic Cable Restraint Systems carry tension only loads along the axis of the cable. They are used in pairs 180-degrees apart to restrain pipe, duct, electrical distribution sys-tems or equipment in each axis. Cable restraints provide a load path between the building and the restrained component to ensure that it moves with the building. Bracing is required on both primary axes for all restrained systems. Spacing is determined by the building code and specifying engineer. Cable restraints are required for isolated systems as rigid restraints such as strut will short circuit the isolation.
Kinetics QuakeLoc™ connector is available for purchase as part of Kinetics QuakeKit-P (Pipe), QuakeKit-D (Duct), and QuakeBulk seismic cable restraint systems. Kinetics QuakeKits are competitively priced and offer substantial labor savings when compared to competitors systems. Each kit includes the necessary hardware to connect to suspended components. Hardware to attach QuakeKit systems to concrete, steel or wood structures is also available.
QuakeKit Capacities
KINETICS QuakeLoc™ Connector
QuakeKit-P
Model
QuakeKit-P/D-2QuakeKit-P/D-3QuakeKit-P/D-4
Max Cable Tension
1000 lbs2100 lbs3350 lbs
Cable Length
15 ft15 ft15 ft
Cable Diameter
1/8 in3/16 in 1/4 in
3 mm5 mm6 mm
4.57 m4.57 m4.57 m
454 kg 953 kg1520 kg
With over 50 years of experience, Kinetics Noise Control has extensive experience in the design, manufacturing and application of innovative products to control sound and vibration. Kinetics pioneered development of precompressed, molded fiberglass pad isolators that would be incorporated into a dynamic new floor isolation system.
Kinetics Noise Control now produces the industry’s largest selection of inspired products to address vibration and noise control, room acoustics, and seismic restraint concerns for almost any application. Value is added with our experienced team of engineer-ing and customer support personnel ready to work with you.
Our experienced staff of over twenty (20) technically trained individuals includes ten (10) licensed Profes-sional Engineers, five (5) holding Master’s degrees and two (2) who have earned Ph.D.’s. These individuals are spread across Engineering and Manufacturing centers located in Columbus, Ohio (USA), Toronto, Ontario (Canada) and Hong Kong (China). Their combined experience spans over 400 years!
Noteworthy Projects• Lou Ruvo Brain Institute, Las Vegas NV• Indu and Raj Soin Medical Center, Beavercreek, OH• Burj Khalifa Tower Dubai• New Quito International Airport, Quito, Ecuador• City of Dreams / Grand Hyatt, Macau• Microsoft headquarters, Beijing• Victoria Harbour Tunnel Project, Hong Kong• The Venetian Hotel and Casino, Macau• City Center, Las Vegas, NV• River Oak Hospital, Jackson MS• Roper St. Francis, Charleston, SC• Kaleida Healthcare, Buffalo, NY• Syracuse VA Hospital, Syracuse, NY• Dublin Methodist Hospital, Dublin, OH• St. Anthony’s Medical Center, St. Louis, MO• McCarren Airport, Las Vegas, NV• American Snuff Company, Memphis, TN• Duke Medical Center, Durham, NC• Filmore Hospital, Genera, NE• ECMC Kidney Care, Buffalo, NY• Columbia College, Hamilton, Ontario• Hamilton Health Science Building, Hamilton Ontario• Toronto Police Station, Toronto, Ontario
QuakeLoc™
MADE IN THE USA
MADE IN THE USA
MADE IN THE USA
MADE IN THE USA
Seismic Cable Restraint Connector for piping, duct, electrical cable trays, and suspended equipment.
®
MADE IN THE USA
MADE IN THE USA
QUAKELOC │ 11/18Kinetics Noise Control, Inc. is continually upgrading the quality of our products. We reserve the right to make changes to this and all products without notice.
MADE IN USA
kineticsnoise.com/[email protected]®
is featured in our new lineup of standard seismic cable restraint systems. Sure to be a contractor favorite, the QuakeLoc™ connector quickly and easily fastens cables used in the seismic restraint of piping, duct, electrical cable trays, and suspended equipment. QuakeLoc™ is proudly made in the USA.
Seismic Cable Restraint Systems carry tension only loads along the axis of the cable. They are used in pairs 180-degrees apart to restrain pipe, duct, electrical distribution sys-tems or equipment in each axis. Cable restraints provide a load path between the building and the restrained component to ensure that it moves with the building. Bracing is required on both primary axes for all restrained systems. Spacing is determined by the building code and specifying engineer. Cable restraints are required for isolated systems as rigid restraints such as strut will short circuit the isolation.
Kinetics QuakeLoc™ connector is available for purchase as part of Kinetics QuakeKit-P (Pipe), QuakeKit-D (Duct), and QuakeBulk seismic cable restraint systems. Kinetics QuakeKits are competitively priced and offer substantial labor savings when compared to competitors systems. Each kit includes the necessary hardware to connect to suspended components. Hardware to attach QuakeKit systems to concrete, steel or wood structures is also available.
QuakeKit Capacities
KINETICS QuakeLoc™ Connector
QuakeKit-P
Model
QuakeKit-P/D-2QuakeKit-P/D-3QuakeKit-P/D-4
Max Cable Tension
1000 lbs2100 lbs3350 lbs
Cable Length
15 ft15 ft15 ft
Cable Diameter
1/8 in3/16 in 1/4 in
3 mm5 mm6 mm
4.57 m4.57 m4.57 m
454 kg 953 kg1520 kg
With over 50 years of experience, Kinetics Noise Control has extensive experience in the design, manufacturing and application of innovative products to control sound and vibration. Kinetics pioneered development of precompressed, molded fiberglass pad isolators that would be incorporated into a dynamic new floor isolation system.
Kinetics Noise Control now produces the industry’s largest selection of inspired products to address vibration and noise control, room acoustics, and seismic restraint concerns for almost any application. Value is added with our experienced team of engineer-ing and customer support personnel ready to work with you.
Our experienced staff of over twenty (20) technically trained individuals includes ten (10) licensed Profes-sional Engineers, five (5) holding Master’s degrees and two (2) who have earned Ph.D.’s. These individuals are spread across Engineering and Manufacturing centers located in Columbus, Ohio (USA), Toronto, Ontario (Canada) and Hong Kong (China). Their combined experience spans over 400 years!
Noteworthy Projects• Lou Ruvo Brain Institute, Las Vegas NV• Indu and Raj Soin Medical Center, Beavercreek, OH• Burj Khalifa Tower Dubai• New Quito International Airport, Quito, Ecuador• City of Dreams / Grand Hyatt, Macau• Microsoft headquarters, Beijing• Victoria Harbour Tunnel Project, Hong Kong• The Venetian Hotel and Casino, Macau• City Center, Las Vegas, NV• River Oak Hospital, Jackson MS• Roper St. Francis, Charleston, SC• Kaleida Healthcare, Buffalo, NY• Syracuse VA Hospital, Syracuse, NY• Dublin Methodist Hospital, Dublin, OH• St. Anthony’s Medical Center, St. Louis, MO• McCarren Airport, Las Vegas, NV• American Snuff Company, Memphis, TN• Duke Medical Center, Durham, NC• Filmore Hospital, Genera, NE• ECMC Kidney Care, Buffalo, NY• Columbia College, Hamilton, Ontario• Hamilton Health Science Building, Hamilton Ontario• Toronto Police Station, Toronto, Ontario
QuakeLoc™
MADE IN THE USA
MADE IN THE USA
MADE IN THE USA
MADE IN THE USA
Seismic Cable Restraint Connector for piping, duct, electrical cable trays, and suspended equipment.
MADE IN THE USA
MADE IN THE USA
QUAKELOC 6/12Kinetics Noise Control, Inc. is continually upgrading the quality of our products. We reserve the right to make changes to this and all products without notice.
kineticsnoise.com/quakeloc/[email protected]
Dublin, Ohio, USA Las Vegas, Nevada, USA Toronto, Ontario, Canada Hong Kong, China
QUAKE KITSQuakeKit-D for Duct, Suspended Equipment & ElectricalKinetics QuakeKit-D is specifically designed to provide the necessary components to properly restrain duct, electrical components and suspended equipment. Each prepackaged kit contains:
2 QuakeLoc™ connectors
2 Thimbles
4 KSUA-2 brackets
2 15-ft swaged cables
Suspended Equipment Example
QuakeLoc™ connector
KSUA Cable Attachment Brackets
KHRC Rod Stiffener Kit
Kinetics Isolation Hangers
QuakeKit-P for PipingBuilding code requires piping to be braced both in transverse and longitudinal directions. Kinetics QuakeKit-P is specifically designed to provide the necessary components to properly restrain a piping system. Each prepackaged kit contains:
2 QuakeLoc™ connectors
2 Thimbles2 KSUA-2 brackets
2 15-ft swaged cables
2 KSCA brackets and the necessary hardware to
connect to a threaded rod
Suspended Piping Example
QuakeLoc™ connector
KSUA Cable Attachment Brackets
KHRC Rod Stiffener Kit
Kinetics Isolation Hangers
Quake Kit-D Quake Kit-P QuakeBulk
QuakeBulkKinetics QuakeBulk is a universal kit specially designed for application where more than 15-ft of cable will be required. Bulk cable sold separately. This prepackaged kit contains:
4 QuakeLoc™ connectors
4 Thimbles
2 KSCA brackets and the necessary hardware to
connect to a threaded rod
2 KSUA-2 brackets
Attachment HardwareKinetics offers a wide range of attachment hardware options depending on the situations. Concrete applications require the use of our model KCCAB cracked concrete anchor, model KMTB CMU block anchor or KAABS adhesive anchor. For steel applications, we can provide bolts, nuts and washers or brackets can be welded directly to steel.
KCCAB KMTB KAABS
QUAKE KITSQuakeKit-D for Duct, Suspended Equipment & ElectricalKinetics QuakeKit-D is specifically designed to provide the necessary components to properly restrain duct, electrical components and suspended equipment. Each prepackaged kit contains:
2 QuakeLoc™ connectors
2 Thimbles
4 KSUA-2 brackets
2 15-ft swaged cables
Suspended Equipment Example
QuakeLoc™ connector
KSUA Cable Attachment Brackets
KHRC Rod Stiffener Kit
Kinetics Isolation Hangers
QuakeKit-P for PipingBuilding code requires piping to be braced both in transverse and longitudinal directions. Kinetics QuakeKit-P is specifically designed to provide the necessary components to properly restrain a piping system. Each prepackaged kit contains:
2 QuakeLoc™ connectors
2 Thimbles2 KSUA-2 brackets
2 15-ft swaged cables
2 KSCA brackets and the necessary hardware to
connect to a threaded rod
Suspended Piping Example
QuakeLoc™ connector
KSUA Cable Attachment Brackets
KHRC Rod Stiffener Kit
Kinetics Isolation Hangers
Quake Kit-D Quake Kit-P QuakeBulk
QuakeBulkKinetics QuakeBulk is a universal kit specially designed for application where more than 15-ft of cable will be required. Bulk cable sold separately. This prepackaged kit contains:
4 QuakeLoc™ connectors
4 Thimbles
2 KSCA brackets and the necessary hardware to
connect to a threaded rod
2 KSUA-2 brackets
Attachment HardwareKinetics offers a wide range of attachment hardware options depending on the situations. Concrete applications require the use of our model KCCAB cracked concrete anchor, model KMTB CMU block anchor or KAABS adhesive anchor. For steel applications, we can provide bolts, nuts and washers or brackets can be welded directly to steel.
KCCAB KMTB KAABS
QUAKE KITSQuakeKit-D for Duct, Suspended Equipment & ElectricalKinetics QuakeKit-D is specifically designed to provide the necessary components to properly restrain duct, electrical components and suspended equipment. Each prepackaged kit contains:
2 QuakeLoc™ connectors
2 Thimbles
4 KSUA-2 brackets
2 15-ft swaged cables
Suspended Equipment Example
QuakeLoc™ connector
KSUA Cable Attachment Brackets
KHRC Rod Stiffener Kit
Kinetics Isolation Hangers
QuakeKit-P for PipingBuilding code requires piping to be braced both in transverse and longitudinal directions. Kinetics QuakeKit-P is specifically designed to provide the necessary components to properly restrain a piping system. Each prepackaged kit contains:
2 QuakeLoc™ connectors
2 Thimbles2 KSUA-2 brackets
2 15-ft swaged cables
2 KSCA brackets and the necessary hardware to
connect to a threaded rod
Suspended Piping Example
QuakeLoc™ connector
KSUA Cable Attachment Brackets
KHRC Rod Stiffener Kit
Kinetics Isolation Hangers
Quake Kit-D Quake Kit-P QuakeBulk
QuakeBulkKinetics QuakeBulk is a universal kit specially designed for application where more than 15-ft of cable will be required. Bulk cable sold separately. This prepackaged kit contains:
4 QuakeLoc™ connectors
4 Thimbles
2 KSCA brackets and the necessary hardware to
connect to a threaded rod
2 KSUA-2 brackets
Attachment HardwareKinetics offers a wide range of attachment hardware options depending on the situations. Concrete applications require the use of our model KCCAB cracked concrete anchor, model KMTB CMU block anchor or KAABS adhesive anchor. For steel applications, we can provide bolts, nuts and washers or brackets can be welded directly to steel.
KCCAB KMTB KAABS
is featured in our new lineup of standard seismic cable restraint systems. Sure to be a contractor favorite, the QuakeLoc™ connector quickly and easily fastens cables used in the seismic restraint of piping, duct, electrical cable trays, and suspended equipment. QuakeLoc™ is proudly made in the USA.
Seismic Cable Restraint Systems carry tension only loads along the axis of the cable. They are used in pairs 180-degrees apart to restrain pipe, duct, electrical distribution sys-tems or equipment in each axis. Cable restraints provide a load path between the building and the restrained component to ensure that it moves with the building. Bracing is required on both primary axes for all restrained systems. Spacing is determined by the building code and specifying engineer. Cable restraints are required for isolated systems as rigid restraints such as strut will short circuit the isolation.
Kinetics QuakeLoc™ connector is available for purchase as part of Kinetics QuakeKit-P (Pipe), QuakeKit-D (Duct), and QuakeBulk seismic cable restraint systems. Kinetics QuakeKits are competitively priced and offer substantial labor savings when compared to competitors systems. Each kit includes the necessary hardware to connect to suspended components. Hardware to attach QuakeKit systems to concrete, steel or wood structures is also available.
QuakeKit Capacities
KINETICS QuakeLoc™ Connector
QuakeKit-P
Model
QuakeKit-P/D-2QuakeKit-P/D-3QuakeKit-P/D-4
Max Cable Tension
1000 lbs2100 lbs3350 lbs
Cable Length
15 ft15 ft15 ft
Cable Diameter
1/8 in3/16 in 1/4 in
3 mm5 mm6 mm
4.57 m4.57 m4.57 m
454 kg 953 kg1520 kg
With over 50 years of experience, Kinetics Noise Control has extensive experience in the design, manufacturing and application of innovative products to control sound and vibration. Kinetics pioneered development of precompressed, molded fiberglass pad isolators that would be incorporated into a dynamic new floor isolation system.
Kinetics Noise Control now produces the industry’s largest selection of inspired products to address vibration and noise control, room acoustics, and seismic restraint concerns for almost any application. Value is added with our experienced team of engineer-ing and customer support personnel ready to work with you.
Our experienced staff of over twenty (20) technically trained individuals includes ten (10) licensed Profes-sional Engineers, five (5) holding Master’s degrees and two (2) who have earned Ph.D.’s. These individuals are spread across Engineering and Manufacturing centers located in Columbus, Ohio (USA), Toronto, Ontario (Canada) and Hong Kong (China). Their combined experience spans over 400 years!
Noteworthy Projects• Lou Ruvo Brain Institute, Las Vegas NV• Indu and Raj Soin Medical Center, Beavercreek, OH• Burj Khalifa Tower Dubai• New Quito International Airport, Quito, Ecuador• City of Dreams / Grand Hyatt, Macau• Microsoft headquarters, Beijing• Victoria Harbour Tunnel Project, Hong Kong• The Venetian Hotel and Casino, Macau• City Center, Las Vegas, NV• River Oak Hospital, Jackson MS• Roper St. Francis, Charleston, SC• Kaleida Healthcare, Buffalo, NY• Syracuse VA Hospital, Syracuse, NY• Dublin Methodist Hospital, Dublin, OH• St. Anthony’s Medical Center, St. Louis, MO• McCarren Airport, Las Vegas, NV• American Snuff Company, Memphis, TN• Duke Medical Center, Durham, NC• Filmore Hospital, Genera, NE• ECMC Kidney Care, Buffalo, NY• Columbia College, Hamilton, Ontario• Hamilton Health Science Building, Hamilton Ontario• Toronto Police Station, Toronto, Ontario
QuakeLoc™
MADE IN THE USA
MADE IN THE USA
MADE IN THE USA
MADE IN THE USA
Seismic Cable Restraint Connector for piping, duct, electrical cable trays, and suspended equipment.
MADE IN THE USA
MADE IN THE USA
QUAKELOC │ 11/18Kinetics Noise Control, Inc. is continually upgrading the quality of our products. We reserve the right to make changes to this and all products without notice.
MADE IN USA
kineticsnoise.com/[email protected]®
