MAGNET SEAL PACK,TO FORM 8MM

V04/09/2014

ASSEMBLY INSTRUCTIONS

CORNER ENTRY ENCLOSUREHINGED

T HESE INSTRUCTION REPLACE THE SET SUPPLIED

W ITH THE SHOWER DOORS.

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION

1) General Information

2) Addition notes

Please inspect this product upon delivery. any missing parts or manufacturing

defects must be reported immediately to the supplier. Damage of defects reported

later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID

HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.

Glass breakage claims will not be accepted after the product has been unpacked.

Please note--alumimium is a soft metal, and undergoes a series of extrusion.

fabrication, polishing and anodising processes in order to create your finished

shower enclosure. Some light surface marks are normal, and is a result of the

manufacturing processes. Quality control has ensured that this item is of a good

standard, and is fit for purpose.

Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: this product is heavy and may require two people to install.

TOOLS REQUIRED

This product is heavy and may require two people to install.

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Hammer

Silicone Sealant

1

ASSEMBLY INSTRUCTIONS-DRAWING

2

(1)

(2)

(3)

(4)(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15) (16) (17) (18)(19)

(20)

(1) 2. x Wall Bracket

(2) 2. x Cover Cap (Wall Post A)

(3) 2. x Cover Cap (Vertical Profile)

(4) 2. x Wall Post

(5) 2. x Vertical Profile

(6) .

(7)

2

.

x Vertical Seal

(8) .

(9)

2

.

x Moving Door

(10).

8x Wall Plugs

8x Screws 4x30mm

2x Handle

(11) .

(12) .

(13) .

(14) .

(15) .

(16) .

(17) .

(18)

6

.

x Screw Cover caps

(19)

(20)

6

.

.

x Screws 4x12mm

6x Screw Cover Cap Washers

2x Top Hinge2x Bottom Hinge

2x Curved End Cover Cap

(LH+RH)

2x Bottom Seal

2x Drip Strip

1x End Cover Cap

2x Magnet Seal (Moving Door)

3

ASSEMBLY INSTRUCTIONSIf you require help, we advise you firstly contact a competent plumberInstallation Steps

Step 1THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.

20

20 20

760/800/900760/800/900

1020

10

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS

SHOWER PANEL / DOOR,

Step 2

Step 3

6mm

4x30

x4

x4

x4

x4

4

20

MOVING DOORFIXED PANEL

Step 4

Step 5

5

INSIDE VIEW INSIDE VIEW

MOVING DOOR

FIXED PANEL

Step 6

Step 7

6

INSIDE VIEW INSIDE VIEW

x6

x6

x6

3.0mm

Step 8

Step 9

INSIDE VIEW

!

!

How to adjust the width of the

hinged door

Minimum 10mm internal overlap required

Glass panel

Glass panel

Vertical profile

Vertical profile

Wall profile

Wall profile

Wall

Wall

Maximum adjustment

Minimum adjustment

7

Sil icone

Sil i

cone

Silicone (outside edge only) where the vertical profiles meet the wall, and the

glass panels meet the tray.

6mm

x2

x2

x2

Step 10

Step 11

8

CARE AND MAINTENANCE

1) AFTER CARE INSTRUCTIONS

2) MAINTENANCE

Regularly clean your shower product with warm soapy water

Clean the plastic parts with a cloth and mild detergent. Never

use any abrasive creams, dissolvents, acetone or detergents

and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained

in these instructions. The supplier reserves the right to introduce

technical changes without notice.

to prevent lime scale build up. Do not use abrasive cleaning

fluids or materials, or strong chemical cleaners as this will

damage the product surface.

COMMITMENT TO QUALITY

It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you

firstly contact a competent plumber. However we understand that

this may not always be the case, so should you experience

any problems please contact out customer services quoting

the following:

Product name: 8mm Hinged Corner door

Customer help line number:0344 804 48 48

Product code: MAGSEAL8

9

INSTALLERS NOTES

10

/2014612

/14

Shower enclosures with aluminium profiles and safety glass

The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.

We suggest you take it to the local landfill site and discard in the designated bins.