Vers

ion

11/1

6

MAINTENANCEOF TURBINES.

PREPARATION1

A. REMOVING THE INSTRUMENT

• Remove the rotary instrument from the chuck mechanism

B. PRE-DISINFECTION

• External disinfection

Do not immerse the instrument in a disinfectant bath.

A B

CLEANING2

A. CLEAN UNDER RUNNING WATER AT <38°C

B. REMOVING DIRT/DEPOSITS

• Carefully remove all traces of dirt or deposits from the spray nozzles using the Bien-Air cleaning wire

• Dry the nozzles with compressed air then dry the rest of the instrument with a cloth

Do not immerse in an ultrasonic cleaner

C . INTERNAL AND EXTERNAL CLEANING WITH SPRAYNET

• Shake the Spraynet before use

• Use the Spraynet attachment 1 * ( for 2-/3-way and 4-way turbines, see inset below)

• Keep the tip of the instrument pointing down and protect with an absorbent cloth; press the Spraynet button down for 1 second

• Clean the exterior of the turbine with a cloth soaked in Spraynet

A B

C C

C

2-/3-way

4-way

C’

FOR 2-/3-WAY AND 4-WAY TURBINES ONLY

C‘. CLEANING THE INSIDE WITH SPRAYNET FOR 2-/3-WAY AND 4-WAY TURBINES ONLY

• Use the Spraynet attachment 2 *

• Keep the tip of the instrument pointing down and protect with an absorbent cloth; press the Spraynet button down for 1 second

Spray into the opening as shown in the illustrations for “2-/3-way” and “4-way”

Refer to the user manual for the product for the complete cleaning and sterilisation maintenance procedures. This medical device is supplied in "non sterile" condition. Please ensure that this procedure is followed before the device is used.

* All the references for the attachments are given on the last page of the document.

Vers

ion

11/1

6

* All the references for the attachments are given on the last page of the document.

DISINFECTION3

A. DISINFECTION USING SURFACE DISINFECTANT (follow the manufacturer's instructions for use)

Do not immerse the instrument in a disinfectant bath

OR

B. THERMAL DISINFECTION (follow the manufacturer's instructions for use)

LUBRICATION4

A. LUBRICATION WITH LUBRIMED

OR

B. LUBRICATION WITH LUBRIFLUID• Shake the Lubrifluid before use

• Use the Lubrifluid attachment 2 , 3 or 4 depending on the type of instrument *(For 2-/3-way and 4-way turbines, see inset below)

• Keep the tip of the instrument pointing down and protect with an absorbent cloth; press the Lubrifluid button down for 1 second

• Then, run an operating test for 30 seconds at low speed to remove any surplus lubricant

• Store immediately: store the instruments with the tip pointing downwards so that any oil residues can flow out

A B

A

B

B’

B

A A

B‘. INTERNAL LUBRICATION WITH LUBRIFLUID FOR 2-/3-WAY AND 4-WAY TURBINES ONLY

• Use the Lubrifluid attachment 2 *

• Keep the tip of the instrument pointing down and protect with an absorbent cloth; press the Lubrifluid button down for 1 second

Spray into the opening as shown in the illustrations for “2-/3-way” and “4-way”

A. PLACE THE TURBINE IN A STERILISATION BAG

B. STERILISE IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS

• Instruments bearing the symbol can be sterilised in an autoclave

Only sterilise instruments which have been cleaned and lubricated

BA

STERILISATION5

FOR 2-/3-WAY AND 4-WAY TURBINES ONLY

2-/3-way

4-way

Unifix MultiFlex ®

Vers

ion

11/1

6

MAINTENANCEACCESSORIES

2

Black Pearl Eco 3- and 4-way

3

Bora L, Boralina, Prestige L, Tornado L, Boralina

4

Bora LK, Prestige LK, Tornado LK

1

2

1

3

2

Black Pearl Eco 3- and 4-way

1

Bora L / LK, Boralina, Prestige L / LK, Tornado L / LK

Bien-Air Dental SA Länggasse 60 Case postale 2500 Bienne 6, Switzerland Tel. +41 (0)32 344 64 64 Fax +41 (0)32 344 64 91 dental@bienair.com www.bienair.com

AQUACARE500 ml cleaning sprayPack of 6REF. 1600617-006

SPRAYNET500 ml cleaning sprayPack of 6REF. 1600036-006

LUBRIFLUID500 ml lubricantPack of 6REF. 1600064-006

LUBRIMEDPack of 6 cartridgesREF. 1600037-006

BIEN-AIR CLEANING WIREPack of 10REF. 1000001-010

LUBRICAREMaintenance systemREF. 1600915-001