Material Safety Data Sheet O ELANTAS ELAN-Tron® C 301 … · 2021. 4. 1. · D002 Corrosive Diethylenetriamine 111-40-0 Diethylenetriamine 111-40-0 Diethylenetriamine 111-40-0 NOT

Material Safety Data Sheet O ELANTAS Electrical Insulation

ELAN-Tron® C 301 Hardener Version 2 Revision Date 06/07/2010 Print Date 06/07/2010

SECTION 1. PRODUCT AND COMPANY IDENTIFICATION

Product name : Product Use Description :

Company :

Prepared by : Teleplione : Visit our web site : E-mail address : Emergency telephone :

SECTION 2. HAZARDS IDENTIFIOl

Emergency Overview

Form Colour Odour Hazard Summary

OSHA Regulatory Status

This material is considered haza CFR1910.1200)

Potential Health Effects

Eyes

Skin

Ingestion

ELAN-Tron® C 301 Hardener Epoxy Hardener

ELANTAS PDG, INC. 5200 North 2nd Street St. Louis MO 63147 Todd Thomas, Manager Regulatory Affairs (314) 621-5700 www.elantas.com [email protected] INFOTRAC- 1-800-535-5053

TION

liquid colourless irritating HARMFUL IN CONTACT WITH SKIN. MAY CAUSE SENSITIZATION BY SKIN CONTACT. CAUSES SEVERE BURNS. RISK OF SERIOUS DAMAGE TO EYES. IRRITATING TO RESPIRATORY SYSTEM. MAY CAUSE SENSITIZATION BY INHALATION.

rdous by the OSHA Hazard Communication Standard (29

May cause permanent eye injury. Causes severe irritation and pain. Direct contact with the product or exposure to vapors or mist may cause stinging, tearing and redness. Corneal damage may occur. May cause blindness.

Causes severe skin burns. Contact may cause irritation and sensitization. May produce central nervous system depression with headache and/or nausea.

Ingestion may cause gastrointestinal irritation, nausea. vomiting and diarrhoea.

1 /10

http://www.elantas.com

mailto:[email protected]

Material Safety Data Sheet

ELAN-Tron® C 301 Hardener Version 2 Revision Date 06/07/2010

O ELANTAS Electrical Insulation

Print Date 06/07/2010

Inhalation

Chronic Exposure

Aggravated Medical Condition

Primary Routes of Entry

Exposure can result in irritation and corrosive action in the mouth, stomach tissue and digestive tract. Causes severe digestive tract burns.

: May cause respiratory tract sensitization. May cause upper respiratory tract irritation. May cause severe irritation and burns to mucous membranes.

: Chronic exposure may cause bronchitis and asthma.

: Overexposure may aggravate existing eye, skin, and/or respiratory disorders. Asthma

: Inhalation Skin contact Skin Absorption Eyes

Carcinogenicity:

No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by lARC.

No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcinogen by OSHA.

No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP.

No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcinogen byACGIH.

Environmental Effects

Environmental Effects : No information available.

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical nature

Aliphatic Amine

Hazardous components

The specific chemical identity/weight percent of proprietary ingredient(s) is a trade secret

Component CAS-No. Weight percent

2/ 10



Diethylenetriamine 111-40-0 60.00 -


100.00 1

SECTION 4. FIRST AID MEASURES

First aid procedures

Inhalation

Skin contact

Eye contact

Ingestion

Notes to physician

Risks

If inhaled, remove to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. Consult a physician.

In case of contact, immediately flush skin with soap and plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Wash and thoroughly clean contaminated clothing and shoes before reuse. Consult a physician.

In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Consult a physician.

If swallowed, consult a physician. Do NOT induce vomiting. If victim is fully conscious, give a cupful of water.

No information available.

SECTION 5. FIRE-FIGHTING MEASURES

Flammable properties

Flash point

Suitable extinguishing media

Unsuitable extinguishing media

Special protective equipment for fire-fighters

Specific hazards during fire fighting

98 °C (210.00 °F)

Carbon dioxide (C02) Dry chemical Foam Water mist

Water spray Water spray jet

In the event of fire, wear self-contained breathing apparatus. Use personal protective equipment.

Do not use a solid water stream as it may scatter and spread fire. The pressure in sealed containers can increase under the influence of heat. Thermal decomposition can lead to release of irritating gases and vapours.

3 / 10


ELAN-Tron® C 301 Hardener Version 2

Hazardous decomposition : products due to incomplete combustion.

Further information :

Revision Date 06/07/2010 Print Date 06/07/2010

Carbon oxides nitrogen oxides (NOx) Material will polymerize at very high temperatures.

Remove ignition sources Immediately evacuate personnel to safe areas. Use a water spray to cool fully closed containers.

SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions :

Environmental precautions

Methods for containment :

Methods for cleaning up

Additional advice :

Remove all ignition sources. Ventilate area. Avoid breathing vapors. Refer to protective measures listed in sections 7 and 8.

Clean contaminated floors and objects thoroughly while observing environmental regulations.

Stop leak. Dike and contain spill.

Absorb with inert absorbent material and dispose of in accordance with applicable regulations.

Shut off source of spill if it can be done safely.

SECTION 7. HANDLING AND STORAGE

Handling

Handling :

Storage

Advice on common storage :

Keep closure tight and container upright to prevent leakage. Containers should be grounded when being emptied. Never use pressure to empty. ATTENTION: Emptied containers may retain hazardous residue and explosive vapors. Keep away from heat, sparks and flames. Do not cut, puncture or weld on or near this container. Follow label warnings until container is thoroughly cleaned or destroyed.

Do not store above 49°C (120 °F). Do not store near acids.

SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure Guidelines

4 / 10





Components with workplace control parameters

Components

Diethylenetriami ne

CAS-No.

111-40-0

Value

TWA

TWA

Control parameters 1 ppm

1 ppm 4 mg/m3

Update

2007-01-01

1989-01-19

Basis

ACGIH

OSHA PO

Engineering measures


Personal protective equipment

Eye protection :

Hand protection :

Skin and body protection :

Respiratory protection

Hygiene measures

Use with adequate ventilation. All application areas should be ventilated in accordance with applicable OSHA regulations. (29 CFR 1910.94)

Use safety eyewear designed to protect against splash of liquids. Ensure that eyewash stations and safety showers are close to the workstation location.

Impervious gloves

Impervious clothing Choose body protection according to the amount and concentration of the dangerous substance at the work place.

Wear an appropriate, properly-fitted respirator (NIOSH/MSHA approved) during and after application unless air monitoring demonstrates that vapor/mist levels are below applicable limits. Follow respirator manufacturer's directions for respirator use.

Wash thoroughly after handling. Do not get in eyes. Do not get on skin. Avoid prolonged or repeated breathing of vapor.

SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Form Colour Odour Odor Threshold Flash point

liquid colourless irritating no data available 98 °C (210.00 °F) Method:

5/ 10



Ignition temperature Lower explosion limit Upper explosion limit Molecular Weight

PH Freezing point Boiling point/boiling range

Vapour pressure

Evaporation rate

Density

Bulk density

Partition coefficient: n-oct an 0 I/water Relative vapour density

SECTION 10. STABILITY AND REA

Conditions to avoid

Materials to avoid

Hazardous decomposition products

Chemical stability

SECTION 11. TOXICOLOGICAL INF

Acute oral toxicity (Component)


no data available no data available no data available 103.00 g/mol

no data available no data available 207 °C (405 °f)

<0.19hPa

1

0.94 g/cm3 at 21 °C(70 °F) (1.013 hPa)

940 kg/m3

no data available

13.038

CTIVITY

Heat, flames and sparks. Nitrosamines, many of which are known to be carcinogens. may be formed when this product comes in contact with nitrous acid, nitrites, or atmospheres with high nitrous oxide concentrations.

Strong oxidizing agents Metals Acids

Carbon dioxide, carbon monoxide and toxic vapors. nitrogen oxides (NOx) Hydrocarbons Ammonia

Stable

ORMATION

Component: 111-40-0 Diethylenetriamine LD50 rat Dose: 1,080 mg/kg

6/ 10





Acute dermal toxicity (Component)

Acute inhalation toxicity (Component)

Skin irritation (Component)

Eye irritation(Component)

Component: 111-40-0 Diethylenetriamine LD50 rabbit Dose: 1,050 mg/kg

Component: 111-40-0 Diethylenetriamine LC50 no data available

Component: 111-40-0 Diethylenetriamine rabbit Result: Corrosive to skin

Component: 111-40-0 Diethylenetriamine rabbit Result: Corrosive to eyes

SECTION 12. ECOLOGICAL INFORMATION

Additional ecological information (Product)

no data available

SECTION 13. DISPOSAL CONSIDERATIONS

Further information Dispose of in accordance with applicable Federal, State, and local regulations. Under the Resource Conservation and Recovery Act (RCRA) regulations, it is the responsibility of the product user to determine, at the time of disposal, whether a material should be classified as a hazardous waste. Consult your attorney or appropriate regulatory affairs officer for information on proper disposal.

SECTION 14. TRANSPORT INFORMATION

DOT

lATA

UN Number : Proper shipping name : Class : Packing group :

UN Number Description of the goods Class Packing group ICAO-Labels Packing instruction (cargo aircraft) Packing instruction (passenger aircraft)

2079 DIETHYLENETRIAMINE 8 II

: 2079 : DIETHYLENETRIAMINE : 8 : II : 8 : 812

: 808

7/ 10





IMDG

Package Instructi quantity)

UN Number Description of the Class Packing group IMDG-Labels EmSNumberl EmSNumber2 Marine pollutant

on (Limited

goods

Y808

UN 2079 DIETHYLENETRIAMINE 8 II 8 F-A S-B no

SECTION 15. REGULATORY INFORMATION

HMIS Classification Health hazard: 3 Chronic Health Hazard: * Flammability: 1 Reactivity: 0 PPLSafety Glasses, Gloves, Dust and Vapor Respirator

National Fire Protection : IIIB Association (NFPA) Class

Emergency Planning Community Right-To-Know (EPCRA)

SARA 302 Components : SARA 302: No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302.

If listed below, this product contains toxic chemical(s) subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthonzation Act of 1986 and 40 CFR part 372.

SARA 311/312 Hazards Acute Health Hazard Chronic Health Hazard

Toxic Substances Control Act (TSCA) TSCA Status : We certify that all of the components of this product are either

listed on the TSCA Inventory or are not subject to the notification requirements (exempt)

Clean Air Act & Related Information

Non-volatile (Wt) 0% Method: Not available

8/ 10



Non-volatile information is not a

Hazardous Air Pollutants


specification.

If not listed above, this product does not contain HAPs at 1%or 0.1% or greater. Refer to Section 3 for HAP weight percentage.

Resource Conservation and Recovery Act

EPA Hazardous Waste Code(s)

State Laws

Massachusetts Right To Know Components

Pennsylvania Right To Know Components

New Jersey Right To Know Components

New Jersey Trade Secret Registry Number for the product (NJ TSRN)

California Prop. 65 Components

D002 Corrosive

Diethylenetriamine 111-40-0



NOT APPLICABLE

This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.

Canadian Environmental Protection Act

Domestic Substances List DSL Status

WHMIS Classification

We certify that all of the components of this product are listed on the DSL.

D2B E

SECTION 16. OTHER INFORMATION

Further information

9/ 10

Material Safety Data Sheet ^ \ PI ikMTikC Electrical Insulation

ELAN-Tron® C 301 Hardener Version 2 Revision Date 06/07/2010 Print Date 06/07/2010

The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other matenals or in any process, unless specified in the text.

10 /10

Material Safety Data Sheet ^ \ P I i k M T i k C Electrical Insulation

E 203 BLACK SEALER PASTE Version 2 Revision Date 06/07/2010 Print Date 06/07/2010

SECTION 1. PRODUCT AND COMPANY IDENTIFICATION

Product name Product Use Descnption

Company

Prepared by Telephone Visit our web site E-mail address Emergency telephone

SECTION 2. HAZARDS IDENTIFI

Emergency Overview

Form Hazard Summary

OSHA Regulatory Status

This matenal is considered ha CFR1910.1200)

Potential Health Effects

Eyes

Skin

Ingestion

Inhalation

Chronic Exposure

Aggravated Medical

E 203 BLACK SEALER PASTE Electncal Insulation

ELANTAS PDG, INC. 5200 North 2nd Street St. Louis MO 63147 Todd Thomas, Manager Regulatory Affairs (314) 621-5700 www.elantas.com [email protected] INFOTRAC- 1-800-535-5053

NATION

: liquid : HARMFUL IN CONTACT WITH SKIN.

MAY CAUSE SENSITIZATION BY SKIN CONTACT. IRRITATING TO EYES.

zardous by the OSHA Hazard Communication Standard (29

: Causes eye irritation.

: May cause allergic reaction. May cause sensitization by skin contact. Prolonged contact may result in discoloration, swelling. scaling, and/or blistering. May be harmful if absorbed through skin.

: Harmful if swallowed. Ingestion may cause gastrointestinal irritation, nausea. vomiting and diarrhoea.

: May cause allergic respiratory reaction. Physical degradation of the cured product (i.e. sanding. abrading, etc.) may pose a dust hazard.

: No evidence of adverse effects from available information.

: Overexposure may aggravate existing eye, skin, and/or

1 /11

http://www.elantas.com

mailto:[email protected]


E 203 BLACK SEALER PASTE Version 2 Revision Date 06/07/2010



Condition

Primary Routes of Entry

Carcinogenicity:

respiratory disorders.

Inhalation Skin contact Eyes

lARC Crystalline silica 14808-60-7

No component of this product present at levels greater than or carcinogen or potential carcinogen by OSHA. NTP Crystalline silica

equal to 0 .1% is identified as a

14808-60-7

ACGIH Crystalline silica 14808-60-7

Environmental Effects

Environmental Effects : No information available.

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical nature

Epoxy Resin Solution

Hazardous components

The specific chemical identity/weight percent of proprietary ingredient(s) is a trade secret

Component

Bisphenol A -Epichlorohydrin based epoxy resin Magnesium silicate talc

Amorphous silica gel

Chlorite

Crystalline silica

CAS-No.

25068-38-6

14807-96-6

112945-52-5

1318-59-8

14808-60-7

Weight percent

30.00 - 60.00

30.00 - 60.00

1.00 - 5.00

1.00-5.00

0.10- 1.00

2/ 11



SECTION 4. FIRST AID MEASURES

First aid procedures

Inhalation :

Skin contact :

Eye contact :

Ingestion :

Notes to physician

Risks

If inhaled, remove to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. Consult a physician.

In case of contact, immediately flush skin with soap and plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Wash and thoroughly clean contaminated clothing and shoes before reuse. Consult a physician.

In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Consult a physician.

If swallowed, consult a physician. Never give anything by mouth to an unconscious person.

No information available.

SECTION 5. FIRE-FIGHTING MEASURES

Flammable properties

Flash point :

Suitable extinguishing : media

Unsuitable extinguishing : media

Special protective : equipment for fire-fighters

Specific hazards during fire : fighting

Hazardous decomposition : products due to incomplete combustion.

> 94 °C (> 201 °F)

Carbon dioxide (C02) Dry chemical Foam Water mist

Water spray Water spray jet

In the event of fire, wear self-contained breathing apparatus. Use personal protective equipment.

Do not use a solid water stream as it may scatter and spread fire. The pressure in sealed containers can increase under the influence of heat.

Carbon oxides nitrogen oxides (NOx) Material will polymerize at very high temperatures.

3/ 11





Further information Remove ignition sources Immediately evacuate personnel to safe areas. Use a water spray to cool fully closed containers.

SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions

Environmental precautions

Methods for containment

Methods for cleaning up

Additional advice

Remove all ignition sources. Ventilate area. Avoid breathing vapors. Refer to protective measures listed in sections 7 and 8.

Clean contaminated floors and objects thoroughly while observing environmental regulations.

Stop leak. Dike and contain spill.

Absorb with inert absorbent material and dispose of in accordance with applicable regulations.

Shut off source of spill if it can be done safely.

SECTION 7. HANDLING AND STORAGE

Handling

Handling

Storage

Advice on common storage

Keep closure tight and container upright to prevent leakage. Containers should be grounded when being emptied. Never use pressure to empty. ATTENTION: Emptied containers may retain hazardous residue and explosive vapors. Keep away from heat, sparks and flames. Do not cut, puncture or weld on or near this container. Follow label warnings until container is thoroughly cleaned or destroyed.

Temperatures exceeding 27°C may cause product viscosity to become unstable. Allow product to stabilize at room temperature prior to use.

SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Exposure Guidelines

Components with workplace control parameters

Components CAS-No. Value Control Update Basis

4 / 11





Magnesium silicate talc

Amorphous silica gel

Crystalline silica

14807-96-6

112945-52-5

14808-60-7

TWA

TWA

TWA

TWA

TWA

TWA

TWA

parameters 20million particles per cubic foot

2 mg/m3

0.1fibre/cm3

2 mg/m3

80 mg/m3

0.025 mg/m3

0.1 mg/m3

1997-08-04

1989-01-19

2008-01-01

2007-01-01

2007-01-01

1989-01-19

OSHA Z3

OSHA PO

ACGIH

ACGIH

OSHA PI

ACGIH

OSHA PO



Personal protective equipment

Eye protection :

Hand protection :

Skin and body protection

Use with adequate ventilation. All application areas should be ventilated in accordance with applicable OSHA regulations. (29 CFR 1910.94) This product contains a particulate(s) that is considered hazardous per OSHA (29 CFR 1910.1200) and is listed in Section III as a precautionary warning. Under normal conditions of use, this product as supplied does not pose a health risk from particulate matter. Physical degradation of the cured product (i.e. sanding, abrading, etc.) may pose a dust hazard. Repeated inhalation of such dust may cause lung injury.

Use safety eyewear designed to protect against splash of liquids. Ensure that eyewash stations and safety showers are close to the workstation location.

Impervious gloves

Impervious clothing Choose body protection according to the amount and concentration of the dangerous substance at the work place.

5/ 11


E 203 BLACK SEALER PASTE Version 2

Respiratory protection

Hygiene measures


Wear an appropriate, properly-fitted respirator (NIOSH/MSHA approved) during and after application unless air monitoring demonstrates that vapor/mist levels are below applicable limits. Follow respirator manufacturer's directions for respirator use.

Wash thoroughly after handling. Do not get in eyes. Do not get on skin. Avoid prolonged or repeated breathing of vapor.

SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Form Odor Threshold Flash point

Ignition temperature Lower explosion limit Upper explosion limit pH Freezing point Boiling point Vapour pressure Evaporation rate Density

Bulk density

Partition coefficient: n-octanol/water Relative vapour density

SECTION 10. STABILITY AND REA

Conditions to avoid

Materials to avoid

Hazardous decomposition products

Chemical stability

liquid no data available > 94 °C (> 201 °F) Method:

no data available no data available no data available no data available no data available no data available no data available no data available 1.6320 g/cm3 at 25 ^€(77 °F) (1.013 hPa)

1,632.2756 kg/m3

no data available

no data available

CTIVITY

Heat, flames and sparks.

Acids, bases, strong oxidizers, & metallic halides (salts).

The by-products expected in incomplete pyrolysis or combustion of epoxy resins are mainly phenolics, CO and water.

Stable at room temperatures; polymerization may occur

6/ 11



SECTION 11. TOXICOLOGICAL INFORMATION

Acute oral toxicity (Component)

Acute dermal toxicity : (Component)

Acute inhalation toxicity : (Component)

Skin irritation (Component) :

Component: 25068-38-6 Bisphenol A- Epichlorohydrin based epoxy resin LD50 rat Dose: 11,400 mg/kg

Component: 14807-96-6 Magnesium silicate talc no data available

Component: 112945-52-5 Amorphous silica gel LD50 rat Dose:> 10,000 mg/kg

Component: 25068-38-6 Bisphenol A - Epichlorohydrin based epoxy resin LD50 rabbit Dose: 23,400 mg/kg


Component: 112945-52-5 Amorphous silica gel LD50 rabbit Dose: > 5,000 mg/kg

Component: 25068-38-6 Bisphenol A - Epichlorohydrin based epoxy resin LC50 no data available


Component: 112945-52-5 Amorphous silica gel LC50 rat Dose: 0.1390 mg/l

Component: 25068-38-6 Bisphenol A - Epichlorohydrin based epoxy resin rabbit Result: Moderate skin irritation

Component: 112945-52-5 Amorphous silica gel rabbit Result: No skin irritation

7/11

Material Safety Data Sheet # ^ E L A N T A S Electrical Insulation


Eye irritation(Component) : Component: 25068-38-6 Bisphenol A - Epichlorohydrin based epoxy resin rabbit Result: Eye irritation


Component: 112945-52-5 Amorphous silica gel rabbit Result: No eye irritation

SECTION 12. ECOLOGICAL INFORMATION

Additional ecological : no data available information (Product)

SECTION 13. DISPOSAL CONSIDERATIONS

Further information : Dispose of in accordance with applicable Federal, State, and local regulations. Under the Resource Conservation and Recovery Act (RCRA) regulations, it is the responsibility of the product user to determine, at the time of disposal, whether a material should be classified as a hazardous waste. Consult your attorney or appropriate regulatory affairs officer for information on proper disposal.

SECTION 14. TRANSPORT INFORMATION

DOT Not dangerous goods

lATA Not dangerous goods

IMDG_US Not dangerous goods

SECTION 15. REGULATORY INFORMATION

HMIS Classification : Health hazard: 2 Flammability: 1 Reactivity: 0 PPI:Safety Glasses, Gloves

National Fire Protection : IIIB Association (NFPA) Class

/11



Emergency Planning Community Right-To-Know (EPCRA)

SARA 302 Components Epichlorohydrin


106-89-8

If listed below, this product contains toxic chemical(s) subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR part 372.

SARA 311/312 Hazards Acute Health Hazard

Toxic Substances Control Act (TSCA) TSCA Status : We certify that all of the components of this product are either

listed on the TSCA Inventory or are not subject to the notification requirements (exempt)

Clean Air Act & Related Information

Non-volatile (Wt)

Non-volatile information is not a

Hazardous Air Pollutants

99% Method: Not available

specification.

If not listed above, this product does not contain HAPs at 1%or 0.1% or greater. Refer to Section 3 for HAP weight percentage.

Resource Conservation and Recovery Act

EPA Hazardous Waste Code(s)

State Laws

Massachusetts Right To Know Components

Pennsylvania Right To Know Components

New Jersey Right To Know Components

Magnesium silicate talc

Bisphenol A - Epichlorohydrin based epoxy resin Magnesium silicate talc Amorphous silica gel

Bisphenol A - Epichlorohydrin based epoxy resin Magnesium silicate talc

Not applicable.

14807-96-6

25068-38-6

14807-96-6 112945-52-5

25068-38-6

14807-96-6

9/ 11


E 203 BLACK SEALER PASTE Version 2

New Jersey Trade Secret Registry Number for the product (NJ TSRN)

California Prop. 65 Components


Amorphous silica gel 112945-52-5 Chlorite 1318-59-8

NOT APPLICABLE

WARNING! This product contains a chemical known to the State of California to cause cancer.

Contains trace concentrations of Epichlorohydrin Crystalline silica 14808-60-7 Carbon black 1333-86-4 Phenyl glycidyl ether 122-60-1 Epichlorohydrin 106-89-8 WARNING! This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

Contains trace concentrations of Epichlorohydrin Epichlorohydrin 106-89-8

Canadian Environmental Protection Act

Domestic Substances List DSL Status

WHMIS Classification

We certify that all of the components of this product are listed on the DSL.

D2A D2B

SECTION 16. OTHER INFORMATION

Further information

The information provided in this Safety Data Sheet is correct to the best of our knowledge. information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use not to be considered a warranty

processing, storage, transportation, disposal and release and is or quality specification. The information relates only to the

specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.

10/11

Material Safety Data Sheet ^ \ P I i k M T i k C Electrical Insulation


11 / 11

Documents

Material Safety Data Sheet O ELANTAS ELAN-Tron® C 301 … · 2021. 4. 1. · D002 Corrosive Diethylenetriamine 111-40-0 Diethylenetriamine 111-40-0 Diethylenetriamine 111-40-0 NOT