Upload
4610660187
View
318
Download
3
Embed Size (px)
Citation preview
Materials selection, welding, forming, Heat treatment, corrossion, NDT
Materials & Welding
Subscribe to Materials & Welding
Email: Subscribe
Visit this group
SATURDAY, AUGUST 14, 2010
Re: [MW:6495] but welding of unequal thickness member asper UW-9 OF ASME SEC VIII DIV 1Taper has to be 1/3 with respect to the thickness difference. The width of the weld can be included in thetaper.
»
Page 1 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
From: asad azmi [[email protected]] Sent: 14/08/2010 13:48 ZE3 To: [email protected] Subject: [MW:6493] but welding of unequal thickness member as per UW-9 OF ASME SEC VIII DIV 1
Dear All,
Good Day.
Please inform me what will be the Minimum length of the taper for butt weld between plates of 10 mmand 20mm Thickness.
Please refer Fig. 2 of the attachment and inform me--
whether length of taper will be distance between edge of plate ( The point from where tapering isstatring ) to root face of the bevel i.e L ORLength of taper will be from edge of plate ( The point from where tapering is statring ) to the point wherethickness of the thicker member becomes equal to thickness of the thinner member i.e L1
What is the maximum angle allowed for tapering.( please refer Fig. 1(a) of the attachment)
Thanks in advance.
Regards
Page 2 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Posted by BR at 10:10 PM 0 commentszz
Asad
--To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant for educationalpurposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant for educationalpurposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
Re: [MW:6494] what is formula of miter cut elbow?
Page 3 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Posted by BR at 6:05 PM 0 comments
What kind of application?
----- Original Message -----From: Usman Anwar [[email protected]]Sent: 14/08/2010 09:24 ZE5To: [email protected]: [MW:6490] what is formula of miter cut elbow?
dear friends,i want to know abt the formula for miter cut elbow of dia 24 inch?thanksregardsusman
--To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant for educationalpurposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
--To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant for educationalpurposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
Page 4 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Posted by BR at 6:05 PM 0 comments zz
[MW:6493] but welding of unequal thickness member as perUW-9 OF ASME SEC VIII DIV 1Dear All,
Good Day.
Please inform me what will be the Minimum length of the taper for butt weld between plates of 10 mmand 20mm Thickness.
Please refer Fig. 2 of the attachment and inform me--
whether length of taper will be distance between edge of plate ( The point from where tapering isstatring ) to root face of the bevel i.e L ORLength of taper will be from edge of plate ( The point from where tapering is statring ) to the point wherethickness of the thicker member becomes equal to thickness of the thinner member i.e L1
What is the maximum angle allowed for tapering.( please refer Fig. 1(a) of the attachment)
Page 5 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Posted by BR at 4:18 PM 0 commentszz
Thanks in advance.
Regards
Asad
--To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant for educationalpurposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
[MW:6492] Welder Qualification and reinforcementHi Guys,
1) I wonder why we will not consider the reinforcement and Root penetration in welder qualification
Page 6 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Posted by BR at 1:35 PM 0 commentszz
thickness range..? as this is also a form of weld deposition.
2) Can we weld a 25 mm thick plate using 2 welders each is qualified to weld 20mm.Welding code isAWS D 1.1
Hope to have your helpful answers.
Thanks & Regards,Ather
Re: [MW:6491] what is formula of miter cut elbow?hi,please refer ASME B31.1 section 104.3.3 and Mandatory Appendix-D..you can find all detail formula formiter elbows.
Thanks & Regards,
(Karthik)
Karthikeyan.S
Getabec Energy Co.,Ltd.379,Moo6,Soi8,Nikhomphatana,
Page 7 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
--
Rayong-21180,Thailand.Phone: 0066 38 897035-8 (Off)Fax: 0066 38 897034Hand Phone: 0066 892512282
--- On Sat, 8/14/10, Usman Anwar <[email protected]> wrote:
From: Usman Anwar <[email protected]>Subject: [MW:6490] what is formula of miter cut elbow?To: [email protected]: Saturday, August 14, 2010, 11:24 AM
dear friends,i want to know abt the formula for miter cut elbow of dia 24 inch?thanksregardsusman
--To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant foreducational purposes only, Users must take their own decisions w.r.t. applicablecode/standard/contract documents.
Page 8 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Home
Subscribe to: Posts (Atom)
Posted by BR at 10:16 AM 0 commentszz
Older Posts
2006 (1)
2007 (94)
2008 (983)
2009 (2497)
2010 (2646)January (225)
February (234)
March (255)
April (385)
May (327)
June (488)
July (462)
To post to this group, send email to [email protected] unsubscribe from this group, send email to [email protected] more options, visit this group's bolg at http://materials-welding.blogspot.com/The views expressed/exchnaged in this group are members personel views and meant for educationalpurposes only, Users must take their own decisions w.r.t. applicable code/standard/contract documents.
BLOG ARCHIVE
Page 9 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
August (270)[MW:0] RE: 6223] NACE recommendation on Bolts & Nu...
RE: [MW:0] minimum butt weld joint
Re: [MW:0] JOINT DESIGN
Re: [MW:0] minimum butt weld joint
Re: [MW:6231] JOINT DESIGN
Re: [MW:6232] ASME PQR-WPS-Impact testing
Re: [MW:6233] Welder Qualification-Thickness range...
Re: [MW:6234] JOINT DESIGN
Re: [MW:6235] Welder Qualification-Thickness range...
Re: [MW:6236] why plsama cutting in ss
RE: [MW:6237] minimum butt weld joint
RE: [MW:6238] FW: 6138] Inconel 690 Tube Bending
[MW:6239] How to select the IQI wire
Re: Re: [MW:6240] ASME PQR-WPS-Impact testing
Re: [MW:6241] How to select the IQI wire
RE: [MW:6242] why plsama cutting in ss
Re: [MW:6243] How to select the IQI wire
RE: [MW:6244] How to select the IQI wire
Re: [MW:6245] How to select the IQI wire
RE: [MW:6248] How to select the IQI wire
Re: [MW:6246] Painting Service Plan?
[MW:6246] Satbalising (Treatment of SA321H
[MW:6250] clad welding
Page 10 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
[MW:6251] Application of B31G - Strength of corrod...
[MW:6252] Solution Annealing of Stainless Steels
[MW:6249] RE: 6219] vacuum chamber
[MW:6253] RE: 6250] clad welding
Re: [MW:6254] How to select the IQI wire
Re: [MW:6255] Solution Annealing of Stainless Stee...
[MW:6256] Re: Solution Annealing of Stainless Stee...
Re: [MW:6257] Satbalising (Treatment of SA321H
Re: [MW:6258] Re: Solution Annealing of Stainless ...
Re: [MW:6260] How to select the IQI wire
Re: [MW:6261] clad welding
Re: [MW:6262] Satbalising (Treatment of SA321H
[MW:6263] ASME SEC IX Impact Test Requirement Clar...
[MW:6264] what is super austentic stainless steel
[MW:6259] G48 TESTING
[MW:6265] Re: Application of B31G - Strength of co...
[MW:6266] Re: Solution Annealing of Stainless Stee...
Re: [MW:6267] How to select the IQI wire
[MW:6268] RE: 6259] G48 TESTING
RE: **** SPAM **** Re: [MW:6269] clad welding
RE: [MW:6270] Re: Application of B31G - Strength o...
RE: [MW:6271] Satbalising (Treatment of SA321H
Re: [MW:6272] RE: 6259] G48 TESTING
Page 11 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
RE: [MW:6273] RE: 6259] G48 TESTING
[MW:6274] Mechanical Tests for PQR
Re: [MW:6275] PWHT above Tempering Temperature
RE: [MW:6276] PWHT above Tempering Temperature
Re: [MW:6277] Mechanical Tests for PQR
RE: [MW:6278] Satbalising (Treatment of SA321H
Re: [MW:6281] Mechanical Tests for PQR
Re: [MW:6280] PWHT above Tempering Temperature
Re: [MW:6279] Re: Solution Annealing of Stainless ...
RE: [MW:6283] PWHT above Tempering Temperature
RE: [MW:6282] Satbalising (Treatment of SA321H
Re: [MW:6284] How to select the IQI wire
Re: [MW:6285] RE: 6250] clad welding
RE: [MW:6286] RE: 6250] clad welding
[MW:6287] WPS
[MW:6288] WPS for API 5L X Grades
RE: [MW:6289] RE: 6250] clad welding
Re: [MW:6290] WPS for API 5L X Grades
[MW:6291] API 1104 CODE ISSUE
[MW:6292] Comparison between NBIC NB-23 and ASME P...
Re: [MW:6293] WPS for API 5L X Grades
[MW:6294] formula for calculating elongation
[MW:6295] tempering of B7 bolts
Page 12 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6306] formula for calculating elongation
[MW:6299] Asme Stamps according section VIII divis...
[MW:6297] Stabalising (Treatment of SA321H
Re: [MW:6296] WPS for API 5L X Grades
[MW:6298] MW: - 6265-Re: Application of B-31G-Stre...
RE: [MW:6300] formula for calculating elongation
[MW:6301] Re: PWHT of Bigger diameter & Long vesse...
Re: [MW:6302] API 1104 CODE ISSUE
Re: [MW:6303] API 1104 CODE ISSUE
[MW:6304] query for ASME SEC IX
Re: [MW:6305] RE: 6250] clad welding
Re: [MW:6307] Asme Stamps according section VIII d...
Re: [MW:6308] Asme Stamps according section VIII d...
Re: [MW:6309] Asme Stamps according section VIII d...
Re: [MW:6311] Asme Stamps according section VIII d...
[MW:6312] Wetting agent for Hydrostatic test
Re: [MW:6310] Asme Stamps according section VIII d...
Re: [MW:6313] Asme Stamps according section VIII d...
Re: [MW:6313] Wetting agent for Hydrostatic test
[MW:6315] Brazing filler metal for Copper to SS321...
[MW:6317] CCOE Certifications
[MW:6318] How To Become Registered Professional En...
[MW:6319] GTAW for complete welding joint
Page 13 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6316] Wetting agent for Hydrostatic test
Re: [MW:6320] CCOE Certifications
Re: [MW:6321] How To Become Registered Professiona...
[MW:6322] RE: 6319] GTAW for complete welding join...
[MW:6326] Base material given under filler metal i...
[MW:6325] FW: 6309] Asme Stamps according section ...
Re: [MW:6323] Comparison between NBIC NB-23 and AS...
[MW:6327] RE: 6323] Porosity in Aluminium welding ...
[MW:6323] Porosity in Aluminium welding Reg.,
[MW:6328] RE: 6323] Porosity in Aluminium welding ...
[MW:6329] RE: 6323] Porosity in Aluminium welding ...
[MW:6330] Power boiler repair before start up
[MW:6331] DOLLYMIX WELDING
Re: [MW:6332] DOLLYMIX WELDING
Re: [MW:6333] Power boiler repair before start up
Re: [MW:6334] Power boiler repair before start up
Re: [MW:6335] Wetting agent for Hydrostatic test
[MW:6336] PWHT of SA516 gr70 cladded by SS410
[MW:6337] Girth Flanges for Heat Exchanges
Re: [MW:6338] Power boiler repair before start up
Re: [MW:6339] Porosity in Aluminium welding Reg.,
RE: [MW:6340] Power boiler repair before start up
Re: [MW:6341] Power boiler repair before start up
Page 14 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6342] Porosity in Aluminium welding Reg.,
[MW:6346] Re: Porosity in Aluminium welding Reg.,
[MW:6343] HARDNESS ON SS WELDING
[MW:6345] Stainless Steel, duplex and super duplex...
[MW:6347] Welding & PWHT of AISI 410
[MW:6348] Re: Stainless Steel, duplex and super du...
[MW:6349] Hydrotesting of pipeline
Re: [MW:6350] Stainless Steel, duplex and super du...
[MW:6351] Re: DOLLYMIX WELDING
[MW:6352] Re: HARDNESS ON SS WELDING
[MW:6353] Re: Hydrotesting of pipeline
Re: [MW:6354] Welding & PWHT of AISI 410
[MW:6355] query regarding ASME SEC IX
[MW:6356] Quarry on an Inspection requirement
[MW:6357] BS EN-10204 3.1 & 3.2
Re: [MW:6358] Hydrotesting of pipeline
ksl.com - Welding scandal could cause problems at ...
[MW:6359] Re: Quarry on an Inspection requirement
[MW:0] Re: BS EN-10204 3.1 & 3.2
[MW:6361] RE: 6359] Re: Quarry on an Inspection re...
Re: [MW:6363] query regarding ASME SEC IX
Re: [MW:6362] query regarding ASME SEC IX
Re: [MW:6364] BS EN-10204 3.1 & 3.2
Page 15 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6365] Re: HARDNESS ON SS WELDING
[MW:6366] QUENCH& TEMPER
Re: [MW:6367] Re: DOLLYMIX WELDING
[MW:6367] Re: BS EN-10204 3.1 & 3.2
RE: [MW:6368] Hydrotesting of pipeline
Re: [MW:6368] BS EN-10204 3.1 & 3.2
Re: [MW:6370] DOLLYMIX WELDING
Re: [MW:6371] DOLLYMIX WELDING
RE: [MW:6372] Hydrotesting of pipeline
[MW:6373] welding of astm B88 TEMPER H58 drawn sea...
[MW:6374] Re: 6359] Re: Quarry on an Inspection re...
[MW:6375] SAW WELDING
Re: [MW:6376] DOLLYMIX WELDING
Re: [MW:6377] Porosity in Aluminium welding Reg.,
Re: [MW:6378] SAW WELDING
Re: [MW:6380] Re: BS EN-10204 3.1 & 3.2
[MW:6379] Flame straightening of distorted weldmen...
RE: **** SPAM **** Re: [MW:6381] SAW WELDING
Re: [MW:6382] Flame straightening of distorted wel...
RE: [MW:6383] Re: Dilution cracking
[MW:6384] Copper Contamination Cracking in Austeni...
[MW:6385] Re: Copper Contamination Cracking in Aus...
[MW:6386] Re: Flame straightening of distorted wel...
Page 16 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
[MW:6387] SAW TEST COUPON DIMENSION
Re: Re: [MW:6388] Flame straightening of distorted...
[MW:6389] Re: SAW TEST COUPON DIMENSION
[MW:6390] Qualification of pipe
Re: [MW:6391] Fwd:How to check the Flange raised f...
RE: [MW:6392] Fwd:How to check the Flange raised f...
RE: [MW:6393] Fwd:How to check the Flange raised f...
Re: [MW:6394] Qualification of pipe
Re: [MW:6395] Qualification of pipe
[MW:6397] What type of Heat treatment to be done
Re: [MW:6396] Qualification of pipe
[MW:6398] SAW WELDING
[MW:6399] MW: 6397- What type of Heat treatment to...
Re: [MW:6400] SAW WELDING
[MW:6401] Re: Copper Contamination Cracking in Aus...
Re: [MW:6402] Porosity in Aluminium welding Reg.,
[MW:6403] RE: 6343] HARDNESS ON SS WELDING
[MW:6407] RE: 6355] query regarding ASME SEC IX
[MW:6406] Training programme in India on API 510,A...
[MW:6405] Welder Performance Qualification
[MW:6404] COMBINED WPS & pqr
RE: [MW:6408] COMBINED WPS & pqr
[MW:6409] I beam selection for single girder under...
Page 17 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6410] RE: 6343] HARDNESS ON SS WELDING
[MW:6411] Pre Qualified WPS
Re: [MW:6412] I beam selection for single girder u...
Re: [MW:6413] Flame straightening of distorted wel...
Re: [MW:6414] Welder Performance Qualification
Re: [MW:6415] Welder Performance Qualification
[MW:6416] Re: COMBINED WPS & pqr
Re: [MW:6417] I beam selection for single girder u...
Re: [MW:6418] I beam selection for single girder u...
[MW:6419] RE: 6411] Pre Qualified WPS
[MW:6420] Re: COMBINED WPS & pqr
[MW:6421] Ductile to Brittle Transition Temperatur...
Re: [MW:6427] Ductile to Brittle Transition Temper...
Re: [MW:6427] Training programme in India on API 5...
[MW:6427] Re: Ductile to Brittle Transition Temper...
[MW:6435] F91 vs F9 grade flanges
Re: [MW:6427] Re: Flame straightening of distorted...
[MW:6431] RE: 6405] Welder Performance Qualificati...
[MW:6431] RE: 6399] MW: 6397- What type of Heat tr...
[MW:6434] Fabrication shop facility Approval for A...
Re: Re: [MW:6431] RE: 6343] HARDNESS ON SS WELDING...
[MW:6436] Queries regarding the repair of casting...
[MW:6424] Alternative Electrode Req for Overlay
Page 18 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6424] Qualification of pipe
Re: [MW:6422] GTAW for complete welding joint
[MW:6424] OK 10.71
[MW:6422] differrence between cs and ks
Re: [MW:6440] differrence between cs and ks
Re: [MW:6439] OK 10.71
Re: [MW:6438] F91 vs F9 grade flanges
Re: [MW:6437] Ductile to Brittle Transition Temper...
RE: [MW:6441] F91 vs F9 grade flanges
[MW:6442] MW: 6431] RE: 6399] MW: 6397- What type ...
Re: [MW:6443] Alternative Electrode Req for Overla...
Re: [MW:6444] F91 vs F9 grade flanges
RE: [MW:6445] OK 10.71
[MW:6449] MW:6444- F91 vs F9 grade flanges
[MW:6450] why do we use dollymix welding technique...
[MW:6448] Re: Queries regarding the repair of cast...
[MW:6447] Ultrasonic peening
[MW:6446] MW: 6427: Ductile to Brittle Transition ...
Re: [MW:6451] Queries regarding the repair of cas...
Re: [MW:6453] MW:6444- F91 vs F9 grade flanges
[MW:6452] PWHT for carbon steel piping system work...
[MW:6454] Welder qualification
[MW:6455] Difficulties in meeting API publication ...
Page 19 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
RE: [MW:6456] Welder qualification dia limits
Re: [MW:6457] GTAW for complete welding joint
[MW:6458] P42 (Monel) to P1 (SA516 G.70) Welding
[MW:6459] WPS qualification
Re: [MW:6460] GTAW for complete welding joint
Re: [MW:6461] WPS qualification
Re: [MW:6473] Welder qualification dia limits
[MW:6462] Purchasing ASME BPV codes
RE: [MW:6463] Purchasing ASME BPV codes
Re: [MW:6464] Purchasing ASME BPV codes
[MW:6465] Re: Ultrasonic peening
[MW:6466] Welder qualified
Re: [MW:6467] P42 (Monel) to P1 (SA516 G.70) Weldi...
Re: [MW:6468] Welder qualified
[MW:6469] Re: Purchasing ASME BPV codes
Re: [MW:6470] Welder qualified
[MW:6471] Re: Fabrication shop facility Approval f...
Re: [MW:6472] Welder qualified
[MW:6474] T-T-T & C-C-T diagram
Re: [MW:6475] P42 (Monel) to P1 (SA516 G.70) Weldi...
Re: [MW:6478] GTAW for complete welding joint
RE: [MW:6477] Welder qualification dia limits
[MW:6476] MW: 6458-P42 (Monel) to P1 (SA516 G.70) ...
Page 20 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Re: [MW:6481] GTAW for complete welding joint
[MW:6479] Re: Welder qualified
[MW:6480] MW:6479] Re: Welder qualified
Re: [MW:6482] Re: Welder qualified
[MW:6483] cylindrically loaded structure
[MW:6484] how can we differenciate between cs and ...
[MW:6485] Re: cylindrically loaded structure
RE: [MW:6486] Re: Welder qualified
RE: [MW:6487] P42 (Monel) to P1 (SA516 G.70) Weldi...
Re: [MW:6488] Re: Welder qualified
RE: [MW:6489] Re: Welder qualified
[MW:6490] what is formula of miter cut elbow?
Re: [MW:6491] what is formula of miter cut elbow?
[MW:6492] Welder Qualification and reinforcement
[MW:6493] but welding of unequal thickness member ...
Re: [MW:6494] what is formula of miter cut elbow?
Re: [MW:6495] but welding of unequal thickness mem...
Searchpowered by
SEARCH THIS BLOG
Page 21 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
with Google Friend Connect
Already a member?Sign in
Followers (3)
Follow
Simple template by Josh Peterson. Powered by Blogger.
FOLLOWERS
Page 22 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 23 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 24 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 25 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 26 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 27 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 28 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 29 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 30 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 31 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 32 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 33 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 34 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 35 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 36 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 37 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 38 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com
Page 39 of 39Materials & Welding
8/15/2010http://materials-welding.blogspot.com/
Click t
o buy NOW!
PDF-XChange
http://ww w.guthcad.com Clic
k to buy N
OW!PDF-XChange
http://ww w.guthcad.com