MaverickTM Firepit - Maverick Firepitmaverickfirepit.com/Docs/maverick_firepit_manual.pdf · This manual details the installation, operation, and maintenance for the Maverick Firepit

MaverickTM Firepit

Owner’s Manual

WARNING: For Outdoor Use Only

WARNING: If the information in this manual is not followed exactly, an uncontrolled fire may result, causing property damage, personal injury or loss of life.

www.MaverickFirepit.com

$10.00 Copyright 2011, T.I. Part # 100‐01265_000

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Educate children and adults of the dangers of the firepit.

Children should be supervised when in the same area as the firepit.

Do not let children play with the firepit.

Keep pets away from the firepit.

2 Introduction

© Travis Industries, Inc. 4110603 100-01265_000

Overview

This manual details the installation, operation, and maintenance for the Maverick Firepit.

Important Registration and Service Information

No other Maverick Firepit has the same serial number as yours. The serial number is on the safety label attached to the firepit (under the front support box). This serial number will be needed in case you require service of any type. To receive full warranty coverage, you will need to show evidence of the date of purchase. Mail your warranty card or visit www.traviswarranty.com to register your Maverick Firepit. If any service issues may arise, contact your dealer for details. See page 13 for warranty registration details.

Important Information

No other Maverick Firepit has the same serial number as yours. The serial number is on the listing label that is chained to the firepit. This serial number may be needed in case you require service. Model: Maverick Firepit Serial Number: Purchase Date: Purchased From:

Register your warranty online at:

www.traviswarranty.com Or, mail your warranty card to:

Travis Industries House of Fire 4800 Harbour Pointe Blvd. SW Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will need to show evidence of the date you purchased your heater. Do not mail your Bill of Sale to us. We suggest that you attach your Bill of Sale to this page so that you will have all the information you need in one place should the need for service or information occur.

Table of Contents 3


Contents

Overview 2

Important Registration and Service Information 2

Important Information 2

Firepit Dimensions 5 Five-Foot Model ............................................. 5 Three-Foot Model .......................................... 5

Packing List 5

Installation Warnings 6 Consult Local Regulations ............................. 6

Placement Requirements 6 Clearances: .................................................... 6

Before You Begin 8 Tools Needed ................................................. 8

Installation Instructions 8

Operating Instructions 11

Maintaining Your Firepit 11 Winterizing the Firepit .................................. 11 Touching up the Paint .................................. 11

Replacement Parts 12

Troubleshooting 12

4 Safety Precautions


! This firepit must be installed in accordance with all local codes, if any.

! This firepit must only be used outdoors in a well-ventilated area. It may not be used in a building, garage, or other enclosed space.

Installation

Do not install in or on cars, trucks, recreational vehicles or boats.

Install this firepit only on a hard, level, non-combustible surface such as concrete, rock or stone. Note that an asphalt or blacktop surface may not be acceptable. Do not use on wooden decks.

Do not force parts together as this can cause personal injury or damage the product.

Do not use this firepit until it is completely assembled and all parts are securely fastened and tightened.

If required in your area, do not use this firepit unless spark guards are securely in place.

Condo/townhome dwellers: Check with your management for requirements and fire codes for using an outdoor firepit in your complex. If allowed, use outside on the ground floor.

Do not use on or under balconies. Contact your local building officials to obtain a

permit and information on any installation restrictions or inspection requirements in your area.

Fuel

Use this outdoor firepit with dry, seasoned cordwood, which will create less smoke and burn hotter and more completely.

Do not use this firepit with solid fuel, such as charcoal briquettes, lump charcoal, manufactured logs, driftwood, trash, leaves, paper, cardboard, plywood, or painted, stained or treated wood. When using softwoods such as pine or cedar, be aware of sparks.

Do not use gasoline, kerosene, diesel fuel, lighter fluid, or alcohol to light or relight fires.

Do not overload the firepit. Do not add additional wood until the fire burns down. NOTE: If any portion of the bowl, lid, or spark guards of the firepit are glowing red this indicates it is overloaded.

General Usage

Keep the firepit clean and free of leaves and debris to ensure safe operation. Do not operate the firepit without first ensuring it is clean.

Keep a portable fire extinguisher or other approved extinguishing equipment, such as a garden hose, readily available when operating this firepit.

Do not store or use gasoline or other flammable liquids or vapors within the vicinity (25 ft., or 7.6 m) of this firepit.

The surfaces of this outdoor firepit are hot when in use. To avoid burns, do not touch the firepit until it has cooled completely (about 45 minutes), unless wearing protective gear such as potholders, gloves, and hot pads. Never touch ashes or coals to test if they are hot.

Avoid breathing smoke from the fire and getting it into your eyes.

Do not lean over the firepit when lighting or while it is in use.

Do not place a hot spark guard or hot firepit tools onto combustible surfaces such as grass, wooden deck, or furniture.

Do not use this outdoor firepit for indoor heating. Toxic carbon monoxide fumes can accumulate and cause asphyxiation.

Keep all electrical cords away from a hot firepit. Using alcohol, prescription or non-prescription drugs

may impair ability to properly assemble or safely operate the firepit.

Do not operate the firepit if: There is a lightning storm or a possible lightning

storm. High wind conditions are present. Do not place clothing or other flammable items on or

near the firepit. If the firepit is not operating properly in any fashion

or if you are uncertain, call your dealer for a full explanation of your firepit and what to expect.

Maintenance

Do not remove, replace, modify or substitute any part of the firepit unless instructions are given in this manual for routine maintenance and cleaning. A trained technician must do all other work.

Allow the firepit, ashes, and coals to extinguish and cool completely before moving, maintaining, or cleaning.

Replace any screen or guard removed for servicing before operating the firepit.

Do not use oven cleaner or abrasive cleaners as they will damage the finish.

Check for signs of damage and creosote build-up after storage or period of non-use. Do not operate until necessary repairs or cleaning have been made.

Manual and Warranty

Operate the firepit according to the instructions included in this manual. The instructions in this manual must be strictly adhered to. Do not use makeshift methods or compromise in the installation. Improper installation will void the warranty and safety listing.

Do not throw this manual away. This manual has important operating and maintenance instructions that you will need at a later time. Always follow the instructions in this manual.

Death, serious injury, or damage to property may occur if the above are not followed exactly.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or maintenance of your firepit, and assumes no responsibility of any consequential damage(s).

Installation (for qualified installers only) 5


Firepit Dimensions

Five-Foot Model

Diameter – 92 inches (2337mm)

Radius from center to Inner Ring – 30 inches (762mm)

Radius from center to outside of Outer Ring – 44.5 inches (1131mm)

Inner dimension – 5 feet (1525mm)

Outer dimension – 8 feet (1830mm)

Height – 12.5 inches (318mm)

Figure 1: Five‐Foot Model

Three-Foot Model

Diameter – 62 inches (1576mm)

Radius from center to Inner Ring – 18 inches (458mm)

Radius from center to outside of Outer Ring – 30 inches (762mm)

Inner dimension – 3 feet (915mm)

Outer dimension – 5 feet (1525mm)

Height – 12 inches (306mm)

Figure 2: Three‐Foot Model

Packing List

Firepit:

(4) decorative covers

(4) sections

(8) bolts

(16) washers

(8) nuts

NOTE: The nuts and bolts attaching the firepit to the pallet are used for installation. Do not throw these away after detaching the firepit from the pallet.

6 Installation (for qualified installers only)


Installation Warnings

! Failure to follow all the requirements may result in property damage, bodily injury, or death.

! This firepit must be installed by a qualified installer.

! The requirements listed below are divided into sections. All requirements must be met simultaneously. The order of installation is not rigid – the qualified installer should follow the procedure best suited for the installation.

Consult Local Regulations

Consult your local city or county regulations for firepits before proceeding with installation. Local regulations govern building and using firepits on private and public property. Some cities and regions require a burning permit before starting an outdoor fire, and seasonal or time of day restrictions. Some firepit regulations dictate the type of materials out of which it should be constructed. Laws may also govern what can be burned in a firepit or how ashes are disposed.

Placement Requirements

! For Outdoor Use Only. Install only in well-ventilated areas.

Do not locate the firepit:

In high traffic areas

Under or near trees, plants and buildings where debris may constantly fall into the firepit. Excessive debris will require high maintenance and/or cause malfunctioning of the firepit.

In places where people, children, and pets may contact the firepit. Guards or fences around the firepit in these locations are recommended.

Clearances:

NOTE: All clearances are measured from the outside edge of the firepit.

The distance from any structure or combustible material to the firepit perimeter shall be a minimum of 25 ft. (7.62 M). Lesser clearances shall be used only where acceptable to the local authority having jurisdiction.

The distance from any overhanging foliage (trees, shrubs, and so on) to the firepit shall be a minimum of 15 feet (4.572 M).



Figure 3: Clearances

NOTE: Heat from the firepit may adversely affect nearby foliage.

25’ (7.62M)

15’ (4.57M)

GravelSoil

Soil

3” (76mm) Non-combustible material for drainage



Before You Begin

! Read this entire manual before you use your new firepit, especially the section "Safety Precautions" on page 13. Failure to follow the instructions may result in property damage, bodily injury, or death.

NOTE: The sections of the firepit are heavy, and may require two people to lift them into place.

Tools Needed

Two ¾” wrenches

Installation Instructions

NOTE: The nuts, bolts, and washers attaching the firepit to the pallet are used for installation. Do not throw these away after detaching the firepit from the pallet. NOTE: The 3‐foot model is shipped in 2 halves, 2 sections per half. You may want to loosen the bolts before assembling, to ensure correct alignment. 1. Determine the location of the firepit. Make sure all clearances are met (see page 6). 2. Prepare the firepit location. We recommend 3” (77mm) of compacted sand or gravel under the firepit,

extending 12” (305mm) beyond the outside edge. 3. Place section 1 as shown in Figure 5; place section 2 as shown in Figure 6. The pipe at the right of each

section fits into the hole at the left of the next section, so that the holes in the brackets align. NOTE: Each section of the firepit is numbered and must be assembled sequentially to ensure proper alignment. You can identify each section by the number of tack welds inside the corner box (see Figure 4). Section 1 has 1 tack weld; section 2 has 2 tack welds, and so on. NOTE: Do not bolt the sections together yet.

Figure 4: Location of Tack Weld

Figure 5: 1st Section

Figure 6: 1st and 2nd Sections Assembled



4. Place sections 3 and 4 as shown below.

Figure 7: Three Sections Assembled

Figure 8: All 4 Sections Assembled

5. Attach the sections, installing the bolts, washers, and nuts in each section, but do not tighten yet. There are top and bottom bolts for each section. See the photos below.

Figure 9: Attaching Sections

Figure 10: Attached Section With Loose Bolts

6. Tighten each bolt with the wrenches in several turns, alternating the bolts. This will help align the firepit.

Figure 11: ¾” Crescent and Ratchet Wrenches

Figure 12: Tightening the Bolts



When tightened, the insides of each bracket section should be flush with each, as shown in the photos below.

Figure 13: Bottom of Section Is Flush

Figure 14: Top and Bottom of Sections Are Flush

7. Attach the 4 decorative bracket covers to the locations provided, starting at the bottom of each section, as shown below.

Figure 15: Attaching the Decorative Cover

Figure 16: Decorative Cover Attached

The completed firepit assembly should look like that in the photo below.

Figure 17: Completed Firepit Assembly

Operation & Maintenance 11


Operating Instructions

! Remove any cover from the firepit prior to operation.

! Inspect the firepit to make sure it is free of debris or objects that may have fallen into the firepit prior to operation.

Start your firepit as follows: 1. Place paper and kindling in the center of the firepit. 2. Light the paper. 3. Add wood to the flame, starting with small pieces first. 4. Add wood to the firepit as desired. Do not overfill the firepit by allowing wood above the sides.

Maintaining Your Firepit

! Failure to inspect and maintain may lead to malfunctioning of the firepit and potentially dangerous situations.

Your Maverick Firepit is designed to be cleaned and maintained easily.

Inspect the firepit before each use.

Keep the firepit clean, and remove any debris that collects in or on the firepit.

The firepit will develop surface rust and discoloration over time – this is normal.

Winterizing the Firepit

In areas where the firepit may not be used in winter, or for an extended period of time, you may wish to cover the firepit. After a period of storage and/or non‐use, check for signs of damage and creosote build‐up. Do not operate until necessary repairs and/or cleanup are executed.

Touching up the Paint

This firepit may be re‐painted using Stove‐Bright metallic black paint available from your dealer.

12 Operation & Maintenance


Replacement Parts

Part # Description Diagram #

Replacement parts can be obtained from your Maverick Firepit retailer (see www.maverickfirepit.com).

Troubleshooting Problem: Possible Cause: Don't Call for Service Until You:

.

Warranty 13


To register your TRAVIS INDUSTRIES, INC. 90-Day Limited Warranty, complete the enclosed Warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants this gas appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to the original purchaser from the date of purchase as follows:

Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty. This charge can vary from store to store.

90-DAY COVERAGE: PARTS Firepit Assembly:

Firepit sections with box covers. Exclusions: Paint and Finish

CONDITIONS & EXCLUSIONS 1. This firepit must be installed by a qualified installer. It must be installed, operated, and maintained at all times in accordance with the instructions in the Owner’s Manual.

Any alteration, willful abuse, accident, neglect, alteration, misapplication or misuse of the product shall nullify this warranty.

2. This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized TRAVIS dealer.

3. Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and, therefore, not covered under warranty. Over-firing (operation when steel glows) of this appliance can cause serious damage and will nullify this warranty.

4. This warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.

5. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees, buildings, roof tops, wind, hills or mountains or other influences from mechanical systems such as fans, etc.

6. This Warranty is void if:

a. The unit has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.

b. The unit is subject to submersion in water.

7. Exclusions to this 90-Day Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation, alteration or adjustment of the manufacturer's settings of components, lack of proper and regular maintenance, damage incurred while the appliance is in transit, alteration, or act of God.

8. This 90-Day warranty excludes damage caused by normal wear and tear, such as discoloration. Also excluded is damage to the unit caused by abuse, improper installation, modification of the unit, drilling of the orifices, or the use of fuel other than that for which the unit is configured. Units are shipped for either natural gas or propane. Confirm fuel configuration with your installer.

9. TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials. Incidental or consequential damages are not covered by this warranty. In some states, the exclusion of incidental or consequential damage may not apply.

11. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the firepit without the express written permission of TRAVIS INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of approval.

12. Any statement or representation of TRAVIS products and their performance contained in TRAVIS advertising, packaging literature, or printed material is not part of this 90-Day warranty.

13. This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way.

14. No dealer, distributor, or similar person has the authority to represent or warrant TRAVIS products beyond the terms contained within this warranty. TRAVIS INDUSTRIES, INC. assumes no liability for such warranties or representations.

15. Travis Industries will not cover the cost of the removal or re-installation.

16. If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.

17. THIS 90-DAY WARRANTY IS THE ONLY WARRANTY SUPPLIED BY TRAVIS INDUSTRIES, INC., THE MANUFACTURER OF THE APPLIANCE. ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, ARE HEREBY EXPRESSLY DISCLAIMED AND PURCHASER’S RECOURSE IS EXPRESSLY LIMITED TO THE WARRANTIES SET FORTH HEREIN.

IF WARRANTY SERVICE IS NEEDED: 1. If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your TRAVIS dealer WITHIN 30 DAYS, giving them proof of purchase,

the purchase date, and the model name and serial number.

2. Travis Industries has the option of either repairing or replacing the defective component.

3. If your dealer is unable to repair your appliance’s defect, he may process a warranty claim through TRAVIS INDUSTRIES, INC., including the name of the dealership where you purchased the appliance, a copy of your receipt showing the date of the appliance’s purchase, and the serial number on your appliance. At that time, you may be asked to ship your appliance, freight charges prepaid, to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your TRAVIS appliance if it is found to be defective in material or workmanship within the time frame stated within this 90-Day warranty. TRAVIS INDUSTRIES, INC. will return your appliance, freight charges prepaid by TRAVIS INDUSTRIES, INC., to your regional distributor, or dealership.

14 Index


Before You Begin ..................................... 8

Dimensions .............................................. 5

Important Registration and

Service Information ............................. 2

Installation Warnings .............................. 6

Maintaining Your Firepit ....................... 12

Operating Instructions .......................... 12

Overview ................................................. 2

Packing List .............................................. 5

Placement Requirements ........................ 6

Recommended Order of

Installation ........................................... 8

Replacement Parts ................................. 13

Troubleshooting ..................................... 13

Winterizing the Firepit ........................... 12

Documents

MaverickTM Firepit - Maverick Firepitmaverickfirepit.com/Docs/maverick_firepit_manual.pdf · This manual details the installation, operation, and maintenance for the Maverick Firepit