MCO05000%3A+Platinum+Series+10-+5+Function+Combination+Machine+w%2F+Spiral+Cutters+

6 FUNCTIONS COMBINED MACHINE

MODEL ML353

OWNER’S MANUAL & PARTS LIST

２

Introduction:

ML353 is a combined universal machine for woodworking. It contains functions in a single compact, practical, and reliable structure.

The electrical equipment includes three asynchronous single - phase motors, 3 main switches complete with minimum voltage coil, 2 three-way switches, 2 commutators, and 4 limit switches which makes ML353 safe and ideal for all users and demanding hobbyists. The machine's structure and the convenient positions of the various functions allow work to be carried out in complete safety. The work tables are made of cast iron processed with a mirror-like surface. The base/stand is made of painted steel. FORESEEN & PROHIBITED OPERATIONS Planing / Thicknessing This permits creating perfectly flat, parallel, and smooth surfaces from rough or salvaged wood.

SawBench This is ideal for hobby and shop work. It is easy to handle and permits precise convenient use.

Moulder / Shaper This is ideal for demanding hobbyists. It was designed with ergonomics in mind so that it is comfortable, easy and safe to use. Tampering with the shaft and assembling bench saws and tools for tenoning is prohibited.

Cutting Carriage Positionable square from 0°to 45°for transversal cutting with goniometer.

Mortising Attachment This is ideal for creating sturdy and precise assemblies. Its work table has a support edge which acts as a stop

３

INDEX OF CONTENTS GENERAL SAFETY RULES

NOTE: Read all these instructions before attempting to operate this product. Save these instructions for future reference. 1. Keep work areas clear. Cluttered areas and benches invite injuries. 2. Consider work area environment. Do not expose tools to rain. Do not use tools in damp or wet locations. Keep work areas well lit. Do not use tools in the presence of flammable liquids or greases. 3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces. 4. Keep other people away. Do not let other persons, especially children, not involved in the work touch of the tool or the extension lead and keep them away from the work area. 5. Store idle tools. When not in use, tools should be stored in a dry locked-up place, out of reach of children. 6. Do not force the tool. It will do the job better and safer at the rate for which it was intended. 7. Use the right tool. Do not force small tools to do the job of a heavy-duty tool. Do not use tools for purposes not intended, for example, do not use circular saws to cut tree limbs or logs. 8. Dress properly. Do not wear loose clothing or jewelry; they can be caught in moving parts. Non-skid footwear is recommended when working outdoors. Wear protective hair covering to contain long hair. 9. Use protective equipment. Use safety glasses. Use face or dust mask if cutting operations create dust. 10. Connect dust extraction equipment. If devices are provided for the connection of dust extraction and collection equipment, ensure these are connected and properly used. 11. Do not abuse the cable. Never pull the power cable to disconnect it from the socket. Keep the cable from the socket. Keep the cable away from heat, oil and sharp edge. 12. Secure work. If possible use clamps or a vice to hold the work. It is safer than using your hand. 13. Do not over reach. Keep proper footing and balance at all times. 14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect power cables periodically and if damaged have them replaced by an authorized service facility. Inspect extension cables periodically and replace if damaged. Keep handles dry, clean and free from oil and grease. 15. Disconnect tools. When not in use, before servicing and when changing accessories such as blades, bits, cutters, disconnect tools from the power supply. 16. Remove adjusting keys and wrenches. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. 17. Avoid unintentional starting. Ensure switch is in “OFF” position when plugging in. 18. Use outdoor extension leads intended for outdoor use and so marked.

４

19. Stay alert. Watch what you are doing, use common sense and do not operate the tool when you are tired. 20. Check damaged parts. Before further use of the tools, it should be carefully checked to determine that it operates properly and perform its intended functions. Check the alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual. Do not use the tool if the switch does not turn on and off. 21. Warning! The use of any accessory or attachment other than one recommended in this instruction manual may present a risk of personal injury. Have your tool repaired by a qualified person. This electric tool complies with the relevant safety rules. Repairs should only be carried out by qualified technicians by using original spare parts, otherwise this may result in considerable danger to the user. 22. Have your tool repaired by a qualified person. This electric tool complies with the relevant safety rules. Repairs should only be carried out by qualified technicians using original spare parts, otherwise it may result in danger to the operator. 23. Never use the machine if the appropriate guard is not in place and correctly adjusted. 24. Do not use knives that are blunt as this increases the danger of kickback of workpieces. 25. Any portion of the cutterblock not being used for planing shall be guarded. 26. When planing narrow short workpieces, a push stick should be used. 27. When planing narrow workpieces, additional measures, such as the use of horizontal pressure devices and spring-loaded guards, may be necessary to ensure safe working. 28. Do not use the machine to cut rebate. 29. Before starting the machine carefully read the instruction manual to avoid any risks of personal injury. 30. The effectiveness of the device for the prevention of kickback and the feed roller should be regularly inspected to ensure safe operation. 31. Tool equipped with chip collection and extraction hoods shall be connected to the dust-and-collecting device.

RECOMMENDATIONS No one must work on a wood machine without first receiving sufficient training concerning the type of work and without being informed of the risks, the precautions to observe and operating instructions for the guards and compulsory safety devices. This machine is designed for wood derivatives. It should not be used for other materials. - Before use we recommend that you carefully read through this manual and that you

respect all instructions contained in it in order to achieve the best results from your machine and to work in complete safety.

- In order to ensure that all safety measures taken into consideration during the design of this machine are met any modification of the machine by the user is forbidden.

- Connection to a sawdust or chipping suction aspirator is obligatory to satisfy all the hygiene/safety conditions and to ensure the correct operation of this machine.

５

- You are strongly recommended to wear protective glasses while using this machine. - Residual risk

As with all wood-working machines with manual adjusting, there is always a risk, even when guards are in place and correctly adjusted, of getting close to tools at a working height which corresponds to the thickness of the wood.

It is essential, therefore, that hands are kept well away

from the dangerous areas and that the end of pass

thruster is used.

RECEPTION HANDLING The machine is delivered fully assembled. When handling with the machine use the certified lifting equipment and safe instruments. The best handling can be done with transport pallet and high lift truck. For lifting the operator can use steel wire rope seal with min diameter 5mm. Before placing the machine on working place, the operator has to consider how large pieces of material, which can be cut in the given room. Safe work with the machine requires enough space around the machine. When you are sure that the placing responds with your idea, flush the machine with max clearance 1mm/1000mm and screw it on the floor. In any cases the operator has to level (flush) the machine in the right way by help of four adjusting screws (placed in adjustable legs). Do not assemble parts (which were disassembled) before the operator has read the whole instruction manuals and has known the machine well. Put the lengthwise rule on the guide way and adjust the length stop and secure. Clamp the sliding table on the bars (guide way) or the support of the run-out arm and secure with the small hand crank. Put the angular rule on the sliding table and secure. Enclosed the operator will find the instruction manual and wrenches necessary. Check the condition of the machine and the number of packages mentioned on the delivery note. If necessary, make the usual reverse to the carrier. WARNING! If reverse are made they must be made on receipt of the goods. Late claims will not be considered. For delivery, the machine is mounted on the wooden crate with wood blocking on the bottom of the crate.

TRANSPORT AND STOCKING During the transport and stocking it is necessary to protect the machine from excessive vibrations and excessive humidity. The machine can be stocked under the roof with air temperature from –250C to 550C. PLACING THE MACHINE ON THE FLOOR Remove the metal sheet clamping. Remove the attachments fixing the machine to the crate (screws and bolts) Clear a sufficient large area round the machine.

Raise the machine slightly and fit two planks under the feet. Use planks which are long enough to act as ramps down to the floor. Pull the machine making sure that it stays on the planks. Once the machine is clear of the crate it will tip. INSTALLATION

６

To guarantee corrected alignment of the working surfaces and prepare a stable, level, concrete floor. WARNING! When handling, take care to avoid shocks or large forces which could cause damage or put the machine out of adjustment. PREPARATION OF THE MACHINE The machine unpainted parts are protected with a factory-applied ultra-fine oily film. It is not necessary to remove it before using the machine. However, if you wish you can remove it, use a cloth soaked spirit. Wipe and clean and then apply a sliding agent (Sliber-gleit, Molycote, etc.).

WORKING CONDITIONS The machine is intended for work under the roof if the following conditions are fulfilled. Air temperature: from 50C to 400C, relative humidity: from 30% to 95% non-condensing, altitude above sea level: max 1000m. The machine must be used as a stationary tool.

ELECTRICAL CONNECTION

７

８

WARNING! Before connection to the mains, check that the mains voltage corresponds with the characteristics of the machine supplied. Use a 1.5 mm2 (min.) supply cable with strengthened insulation, (e.g.HO7). If the length of the cable from the meter to the machine exceeds 10 meters, use 2.5mm2 (min) cable. The internal connections (motor, switch, coil, etc.) are factory wired. SINGLE PHASE 230V CONNECTION: This connection should be made with a 3 core cable and a standard 16A two pole + earth plug. Two wires are provided for the supply (L1, L2) and the third (yellow/green) must be connected to the earth. THREE PHASE 380V CONNECTION: This connection should be made with a 4 core cable and a standard 16A three pole + earth plug. Three wires are provided for the supply (L1, L2, L3) and the fourth (yellow/green) must be connected to the earth terminal. IMPORTANT: Three phase connection necessaries checking the correct direction of rotation of the motor shaft to avoid any problems with the belt drives.

It is essential t start the motor for the first time without a drive belt. If necessary, reverse the position of 2 of the 3 supply wires from the mains to obtain the correct rotation for the normal cutting direction. In the event of a change to the 3 phase supply (variety of supply points, more than one socket in a basement, etc.), it is essential t repeat this check on the direction of rotation as explained above. NOTE: For a temperature below 10 0C we recommend warning up the motor by letting it run off-load on any function. WARNING: Before adjusting or exchanging knives and any maintenance or repairs disconnect the machine from the mains. If the operator is standing at the side of the machine against the backstop, the main cutterblock has to be rotated clockwise (consequently to the right). It is possible to change the rotation direction by exchanging (switch-over) wires (black and/or brown) for three-phase motors. ATTENTION: The machine is injury menaces with the contrary rotation of the cutter block. Switch on the machine only for a while to find out the right direction of rotating (if possible – without tool). The machine is also equipped with brake motor, which is able to stop the machine within required time. However, this brake motor works only when the machine is switched off by pushing red button or emergency stop cover. When the brake does not work properly, it is forbidden to work with the machine. The switch cannot be turned on until the machine is connected to the mains. The switch is turned off automatically by way of neutral protection with outage, it means that it is

９

necessary to switch on the machine again after restoring of the current. Should the machine is switched off frequently in sequence (twice of threefold), check up the machine (the motor functions, the blunt tool, etc.).

The machine can be secured with a padlock placed on the switch which protects the machine from unauthorized usage.

NOTE: If the protection system is not repositioned completely, feedback circuit will restrict the motor starting.

GENERAL INFORMATION This combination-designed machine allows the operator to perform the following operations consecutively: surface planing, thicknessing. Surface planing: Adjustable infeed table, max. cut depth 5mm. Thicknessing: Table height adjustable by hand wheel and button position locking – Chip discharge case for correct chip discharge – Pass limiter – Extraction nozzle – Anti-throw-out pawl.

TECHNICAL DATA

Model No. 10” Motor 1100W, 50Hz, 1 phase Planer tables 1085x250mm Thicknesser tables 600x248mm Cutterblock diameter 75mm Cutterblock speed 4000rpm Fence tilt 0-450

Dust chute 100mm Number of knives 3pcs Max thicknessing height 220mm Max removal thickness 5mm(Planing)

/2.5mm(Thicknessing) Max workpiece width 250mm Net weight 150kgs NOISE LEVELS The manufacturer must inform the user concerning: - the equivalent continuous sound level (Laeq), if the latter exceeds 70 dB(A) at the work

station, - the sound power level (LWA), if the Laeq exceeds 85dB(A) at the work station,

１０

- the peak pressure level (Lpc), if it exceeds 135 dB(A) at the station, - the measuring methods used. REFERENCE STANDARDS: ISO 7960

- Operating conditions for noise measurements

Annex B one-face surface planers Annex C one-face thicknessers

- NF S31-084 – methods for measuring sound levels in a working environment for purpose of evaluating workers’ daily level of sound exposure,

- NF S31-069 – test procedure for measuring noise emitted by machine tools. DEFINITIONS

-Equivalent continuous sound level (LAeq) in dB(A) – the most frequently given figure -Characterizes the receiver, gives the value received as a function of the environment, the distance from the source and/or on the basis of a test procedure for a daily exposure of 8 hours. -sound power level (LWA) in dB(A) -characterizes the noise source, gives an intrinsic value defining the noise emitted by this source independently of the environment. The table below gives the following data for each work station: - the equivalent continuous sound level based on the standard test procedures, - the sound power level - without load and without dust extraction, - under load with vacuuming but without taking into account the noise of the dust

extraction itself. The nature of the premise, the location of the machine within the premises and the presence of a vacuum cleaner nearby can greatly influence the noise level. For example, for a cutting speed of 20m/s of the thicknessing station and a dust extraction air velocity of 10 m/s instead of 20 m/s, the noise level will be reduced by about 9 dB(A). An equivalent continuous sound level of 85 dB(A) is considered to be a danger threshold for a full-time daily exposure of 8 hours. The threshold for 4 hours is 88 dB(A), for 2 hours 91 dB(A), for 1/2 hour 97 dB(A) and for 1/4 hour 100 dB(A). Every halving of the exposure time thus allows the danger threshold to be raised to be 3 dB(A). Wearing noise protection headphones providing sound level attenuation of 15 dB(A) in all cases allows you to stay well below the danger threshold with no limit on exposure time.

Table of Noise Levels Work station sound

pressure Laeq in dB(A) Sound power LWA in dB(A)

Work station no load load no load load SURFACE PLANER 85.5 92 89 98.5 THICKNESSER 94 94.5 107 108

EXHAUSTING SYSTEM The machine has to be connected with exhausting appliance of sawdust during any operation. This exhausting appliance has to embody rapid current of air at least 20 meters per second. The flexible exhausting hose about the diameter of 10 millimeter will be used for connecting. The flexible exhausting hoses should be connected to the exhausting tubes, which placing is following. Planer – the exhausting tube is placed in area of thicknessing table under the planing table – diameter 100mm. Thicknesser – the same exhausting tube as for planing is used, but turned into upper position over the planing tables – diameter 100mm. Liquidation of wooden waste has to be done ecologically, so that it would not worsen our environment. THE ELETRICAL DIAGRAM

WORKING OPERATIONS Planing of narrow workpiecesWhen planing narrow pieces, set the cover of the cutterblock in such a position so that the distance between the workpiece and the cutterblock cover is max 5mm. Then switch on the machine and push the material against the cutterblock (between the cutterblock cover and the rule).

１１

Planing with the inclined ruler Check the angle of the longitutinal ruler when the small cranks are loosen (the position 900 is ensured), retighten the small cranks again and switch on the machine. Push the edge of the workpiece forward and against the rule.

Planing of short workpieces Use the special holder when planing short workpiece. The possible execution you can see on the picture.

１２

Planing of workpieces with small cross section WARNING! There exisits danger of injury when leading the workpiece along the rule incorrectly. Use a wooden angle rule made by yourself. Affix it to the metal rule (for example by two screw clamps).

ADJUSTMENT OF THICKNESSER These are carried out in the factory, proceed with care, as they require a high level of competence.

１３

Thicknessing First adjust the Planer/Thicknesser t the function of thicknessing as follows. Swing away the safety protection. Move the rule to the utmost position off the planing table. Release the planing tables and swing away. Switch on the feeding equipment by hand lever Adjust the thickness of chip and connect the exhausting equipment.

Adjustment of the table Loosen the clamping lever of the table and adjust the thicknessing table to the required height by hand operated wheel. Put the working piece on the table, placing the un-machined side upwards. Lift the table into such a height until it stops at working piece. Using the hand-operated wheel set the stock removal (chip) at a max of 2.5mm. Then affix the table to the required position using the clamping lever. Switch on the machine and push the workpiece forwards. Workpieces with differently shaped ends have to be always inserted its wider end. When planing pitchy wood, it is recommended to coat slightly the thicknessing table with paraffin wax for easier moving. Work area While thicknessing stand in front of the planing table and on that side where is the hand-wheel (for lifting up the thicknessing table). Safety instruments When working with circular saw, spindle moulder, planer and thicknesser, the operator must wear short strengthened apron and safety goggles. It is suitable to use adequate protection of hearing and recommended working footwear. It is forbidden to use working mantle. １４

Workers qualification Only authorized worker specialized in woodworking branches (or worker instructed by this specialist) is allowed to work with the machine. Operators are liable to abide with all safety instruction and regulations, which are valid in his country. TOOLS Recommended tools Cutterblocks have to be marked with manufactures name or logo (marking) and max allowed rotations. Suitable tools for this machine are knives system HSS 250X30X3mm and must meet the reqirements of EN847-1. Exchange and adjustment of knives

WARNING! Disconnect the machine from mains before any adjustment. Swing away the planing tables before exchange of knives. Release five screws (4) by spanner. By the force of the spring (1), the knife (2) will be pushed out automatically. Remove the knife and clean the bearing surface. Clean the new knife carefully. Insert the new knife by screwing five screws (4) so that its extension above the surface of cutterblock in max 1.1mm. The manufacturer recommends the height of extension from 0.7 to 0.8mm. Then tighten the pressing off wedge with five screws. After all the above-mentioned steps are finished make sure to check whether all the five screws are in proper place and fix all protective covers and then try to start the machine by pushing the switch “ON” button. １５

１６

WARNING! Do not use knives with width under 17mm. Its fixing area is too small. MAINTENANCE WARNING! Disconnect the machine from the mains before any maintenance or repairs are carried out. Switch the machine off and lock up the main switch. Lubrication The machine is lubricated at the factory. The electric motor is basically maintenance-free (sealed bearings). The Planer/Thicknesser shafts are journalized in maintenance-free sealed bearings. The machine should be cleaned once a week or after intensive use. The wood feed rollers for thicknessing tend to become fouled when working with resinous woods or poplar. These and the bearing housings should be kept clean. Table surface should be sprayed periodically with a slip enhancing or gliding product, such as Sliber-gleit or Molycote, to enhance sliding of workpieces. The cylindrical thicknesser bed guide and the elevating rack should be cleaned and coated with a slip enhancing product. We advise against using too greasy products which tend to amalgamate with wood dust and harden movements. Surface planer tables A 1 meter steel rule is required to adjust the tables. Slightly loosen the fixing screws of the table which is out of adjustment. Tap slightly on the top or bottom of the table to obtain the correct transverse and longitudinal position, in relation to the shaft. The possibility of adjustment is determined by the set of screw holes in the chassis (the table remains stable after each adjustment to check the geometric position in relation to the other table with the ruler. Make sure that the gap between the tables and shaft is equal at both ends. Tighten firmly after adjustment. Thicknesser table The necessary clearance between the stock and he quill ( cylindrical rack system) is obtained by machining to ensure good overall rigidity and smooth handling. Parallelism between the table work surface and the cutterblock shaft is factory-set. REPAIRS Any defect should not arise if you are operating the machine in the right way and making the suitable maintenance regularly. In case that the sawdust sticks on the cutterblock or the exhausting hose is filled up, switch off the electric motor before you start any repairs, otherwise it could be damaged. Also switch off the electric motor immediately, if the workpiece is getting jammed. Exchange them immediately in such a case. If the machine embodies increase vibrations, check its placing, fixing or balance of tools.

１７

The machine do not work. Check the electrical installation and connection to the mains. The thicknessing table moves only with difficulties. Loosen the clamping lever of the table. The output of the machine is insufficient. Knives are blunt. Too thick chip is adjusted and the operator has to adjust it according to the width and hardness of the wood. The thicknessing table is not clean. The V-belt of the cutterblock is not tightened well. The electric motor has no sufficient output, it is necessary to call qualified electricians. The machine vibrates Knives are blunt or incorrectly adjusted. Knives have no the same width. The machine was installed on uneven surface. Thicknessing is not possible on the machine Too thick chip was adjusted. The thicknessing table is not clean. The working piece slaps against the back table. Incorrectly adjustment of knives or back table. Projection at the end to the workpiece. Uneven surface for planing. Incorrectly adjusted knives or tables. Incorrect pushing or leading of the working piece while planing.

１８

PARTS DIAGRAM FOR PLANER/THICKNESSER

１９

２０

4

２１

２２

PARTS LIST FOR PLANER/THICKNESSER NO. DESCRIPTION QTY NO. DESCRIPTION QTY

1 Right and left spport plate 2 51 Lifting tube bracket 1 2 Plate 2 52 Support base 1 3 Right plate 1 53 Gear assembly 1 4 Bush 1 54 Adjusting bar 1

12 Right cutter block support 1 55 Block 1 13 Left cutter block support 1 56 Block 1 14 Right adjusting wing 1 57 Locking bar assembly 1 15 Left adjusting wing 1 58 Hand wheel 1 16 Locking block 1 59 "C" ring 1 17 Locking block 1 60 Pointer 1 18 Outfeed table 1 61 Depth scale 1 19 Infeed table 1 62 Washer 1 20 Adjusting axle 2 63 Thicknessing table 1 21 Metal plate 1 64 Plate 1 22 Locking handle assembly 2 65 Plate 1 23 eccentric bush 2 66 Gear box 1 24 Screw M8x8 2 67 Gear 1 25 Kick block 15 68 Guide screw 1 26 Axis 1 69 Gear axle 1 27 Support axle 1 70 Bush 1 28 Hex nut M10 2 71 Locking ring 1 30 Scale 1 72 Locking handle 1 31 Adjusting wheel 1 73 Locating block 1 32 Locating plate 1 74 Control handle assembly 1 33 Scale 1 75 Sprocket assembly 1 35 Hex bolt M10x50 2 76 Wheel assembly 1 36 Cutter block assembly 1 77 Wheel assembly 1 37 Ball bearing bush 2 78 Bush 1 38 Cutter block pulley 1 79 Bush 1 39 Protective plate 1 80 Sprocket 2 40 Cutter block 1 81 Driving roller 1 41 Blade locking block 4 82 Pressing roller 1 42 Blade 4 83 Bush 4 43 Sping 8 84 Spring 4 44 Dust chute 1 85 Spring 1 48 Screw 2 86 Connecting plate 1 49 Thicknessing table assembly 1 87 Control handle 1

50 Lifting tube 1 88 Bush 1

２３

NO. DESCRIPTION QTY NO. DESCRIPTION QTY

89 Sprocket 1 503 "C" ring Φ 20 1 90 Chain wheel 1 506 Screw M5x12 5 91 Wheel 1 507 Screw M5x15 4 92 Chain wheel 1 508 Hex bolt M8x20 4 93 Wheel 1 509 Hex nut M8 20

94 Plate 1 510 Washer Φ 5 4

95 Spring 1 511 Washer Φ 8 14 97 Guding fence 1 512 Socket cap screw M8x20 4

98 Cutter block protective fence 1 513 Spring washer Φ 8 22 99 Fence plate 1 514 Socket cap screw M8x16 4

100 supporting plate 1 515 Spring washer Φ 8 11 101 Guiding block 1 516 Socker cap screw M8x30 2 102 Right metal plate 1 517 Pin A6x40 2 103 Left metal plate 1 518 Socker cap screw M6x50 4 104 Connecting plate 1 519 Hex bolt M8x12 2 105 Protective plate 2 520 Socket cap screw M6x35 1 106 Left sliding block 1 521 Hex nut M16 2

107 Right sliding block 1 522 Washer Φ 16 2

108 Handle 1 523 "C" ring Φ 12 4

109 Bolt 2 525 Pin Φ 5x16 1 110 1 526 Screw M5x16 1

112 Locating bar 1 527 Pin Φ 6x10 2 113 Locating bar 1 529 Bolt M6x15 20 114 Motor pulley 1 530 Ball bearing 2 115 U-shaped metal tube 1 531 Pin 6x25 1

116 Locking handle 1 532 "C" ring Φ 25 1

117 Long locking handle 1 533 "C" ring Φ 52 4 118 Short locking handle 1 534 Socket cap screw M6x10 3 119 Angle iron 1 535 Socket cap screw M6x8 8 120 support plate 1 536 Screw M5x8 2

121 Protective plate 1 537 Spring washer Φ 5 13 122 U-shaped bracket 1 538 Screw M6x25 3 123 Locking plate 1 539 Hex bolt M6x15 6 124 Plastic insert 2 540 Hex nut M6 12 125 Switch mounting plate 1 541 Screw M3x10 2 128 Spring 2 542 Support cylinder 1 129 Hex bolt M6x25 2 544 Anti-vibration washer 1 131 Handle assembly 1 545 Socket cap screw M8x16 6 132 Hand wheel 1 546 Socket cap screw M8x30 8

502 Washer Φ 10 2 547 Screw M8x12 1

２４

NO. DESCRIPTION QTY NO. DESCRIPTION QTY

548 Screw M6x12 4 594 Spring washer Φ 5 1 549 Socket cap screw M6x12 18 595 Hex bolt M8x16 4 550 Screw M4x10 2 596 Socker cap screw M6x10 6 551 Screw M4x6 2 599 Motor 1 552 Hex nut M12 2 600 Chang-over handle 1

553 Washer Φ 6 1 601 Rivet Φ 3x5 2 554 Anti-vibration bar 1 608 Screw M6x25 4 555 Lubricating injection hole 1 613 Socket cap screw M6x18 2

556 Seal 1 614 "C' ring Φ 6 2 557 Ball bearing 2 700 Base assembly 1 558 Ball bearing 2 701 Planing table assembly 1 559 Hex bolt M6x65 2 702 Cutter block assembly 1 560 Hex nut M10 6 703 Thicknessing table assembly 1

561 Pin Φ 5x30 1 704 Thicknessing clutch assembly 1

562 "C" ring Φ 10 1 705 Extraction system assembly 1

563 "C" ring Φ 18 1 706 Fence assembly 1 564 Screw M4x10 2 1 565 Bolt 4 566 Socket cap screw M8x70 1 567 Socket cap screw M8x45 1 568 Hex nut M8 4 569 Chain 1 570 Chain 1 571 Chain 1 573 Axle bush 8 574 Pin 5x16 2 575 Handle 1 577 Ball bearing 4 578 Screw M6x10 4

579 "C" ring Φ 22 2 580 Screw M6x10 4 581 Wheel rubber belt 1 582 Ball bearing 1 583 Pin 1 586 V-belt 1

587 Washer Φ 10 2 588 Socket cap screw M6x20 4 589 Hex bolt M5x40 1 590 Screw M5x40 4 591 Nut M8 4

２５

592 Hex nut M6x20 4 593 Socket cap screw M5x8 1

NO. PART NAME Q’TY NO. PART NAME Q’TY

901 Erection shaft 1 939 Gear shaft 1 902 Hand pole 1 940 Crank assemble 1 903 Sheath 1 941 “C” ring 10 1 904 Eccentricity ring 1 942 Larger washer 10 1 905 Pin 1 943 Gear shaft 1 906 Clamp base 1 944 Pin 4X25 1 907 Balling rod 1 945 Ball bearing 51102 1 908 Spring 1 946 Bush 1 909 Pin 4X20 1 947 Fixed ring 1 910 Press block 1 948 Set screw M8X10 2 911 Pin 4X30 1 949 Hex socket cap screw M6X12 1 912 Locking handle 1 950 Big washer 6 1 913 Rocker 1 951 Auto-locking nut M10 1 914 Hex slight-nut M12 1 952 “C” ring 18 1 915 Spring washer 12 1 953 Screw shaft 1 916 Worktable 1 954 Base 1 917 Travel position pin 2 955 Angle support 1 918 Hex nut M8 2 956 Arthrosis bearing SA14ES 2 919 Spring washer 8 2 957 Hex nut M14 2 920 Travel position axis 2 958 Hex socket cap screw M6X20 2 921 Locking bar 2 959 Control pole 1 922 Sliding shaft 2 960 Sheath 1 923 Hex bolt M8X20 4 961 Lift bracket 1 924 Washer 8 4 962 Screw M8X12 2 925 Spring washer 8 4 963 Fixing shaft 2 926 Sliding bracket 1 964 Hex socket cap screw M8X20 2 927 Limited plate 1 965 Adjuster ring 1 928 Spline screw M6X12 2 966 Locking handle 1 929 Locking pole 1 ACCESSORIES 930 Locking handle 1 Protective cover 1 931 Spring 1 Copper washer 2 932 Screw 1 Hex socket cap screw M10x35 3 933 Cuneiform iron 1 Cross-groove screw M6x16 2 934 Set screw M6X30 2 935 Hex nut M6 2 936 Hex bolt M6X65 2

937 Spring washer 6 2

938 Gear box 1

Indication of Label / Drawing

WARNING! An safety instruction label showing how to lower moulding shaft is sticked on the side of height adjusting wheel. WARNING! An safety instruction label showing how to raise mounding shaft is sticked on the side of height adjusting wheel.

WARNING! A safety instruction label is sticked on left side of switch box to control moulding / sawbench operation. WARNING! A safety instruction label is sticked on right side of switch box to ２６

２７

control surface planing / thicknessing operation. Identification of the machine

SPECIFICATIONS Motor – 1# 2000 W, 50Hz , TEFC Motor – 2# 2200 W, 50Hz, TEFC Motor – 3# 2200 W, 50Hz, TEFC

Planer / Thicknessser

Planer table size 250 x 1085 mm Thicknesser table size 250 x 600 mm Cutter block dia. Ф 75 mm

Feeding block dia. Ф 32 mm Cutting knives 3 pcs Fence tilt 0 ~450

Dust chute dia. 100 mm Max planer width 250 mm Max cutting depth 2.5 mm Max thicknessing height 180 mm Cutter block speed 4000 rpm Feed speed 8 m/min

Sawbench

Blade speed 4050 rpm Blade size Ф 250xФ30x3.2x2.2x24T Table size 1200x840(1080) Max cutting height 60 / 900

42 / 450

Spindle Moulder (Tooling not included)

Spindle speed 7000 rpm Spindle dia. Ф 30 mm Spindle travel 130 mm Max cutter dia. Ф 140 mm

Mortising Attachment

Bit housing 16 mm Table size 161 x 368 mm Vertical stroke 0 ~ 80 mm Lateral stroke 0 ~140 mm Table travel rise/fall 0 ~ 90 mm Unit weight 370/445 kg

２８

The wiring diagram

Tool lists enclosed the machine: 1 pc 13X16 solid wrench 1 pc 8x10 solid wrench 1 pc 5.5x7 solid wrench 1 pc 8mm hex. Socket key 1 pc 6mm hex. Socket key 1 pc 5mm hex. Socket key 1 pc 4mm hex. Socket key 1 pc 3mm hex. Socket key Carrying the machine

WARNING! Put your hands at the two sides of the planner table and lift the ２９

table upwards.Do not lift the sides table to carry the machine. TECHNICAL CHARACTERISTICS

Motors The left motor activates ·The bench saw

·The moulding machine The left motor activates ·The planer

·The mortiser Note: The control unit is equipped with ·3 main switches with minimum voltage coil;

·1 push button for immediate stopping;

·A commutator which selects the motors;

·A commutator which selects the “ milling machine ” ；

·A commutator which selects the “ saw” ;

·2 limit switches.

３０

ATTENTION TO SET UP THE PLANER act as follows:

(Fig. 1 )

Select the planer symbol using the three-way switch "A" (Fig.1 ) Push the button " B " of the main switch with Minimum voltage coil (Fig. 1 ).

(Fig. 2 )

Push button on switch “C” to start part of planer / thicknesser. (Fig. 2) For details how to operate part of planer / thicknesser refer to the separate manual of planer / thicknesser.

Note: The following contents/instructions are only subject to part of moulder/sawbench. FUNCTIONS Setup Sawbench / Moulding machine

３１

Fig.3

To set up the saw or milling machine, act as follows Select the saw /milling machine symbol using the two- way switch " A " (Fig.3). Press the button of the main switch " B " with minimum voltage coil (Fig.3). Press the start button " C " (Fig.3 )

FUNCTIONS Bench saw:

Fig.4 Regulate the cutting height by raising or lowering the height lever " A ". Lock the blade into place by turning the knob "B" clockwise Release the blade by turning the knob "B" counter-clockwise. (Fig. 4 )

Fig.5 Lock the square at the desired easurement using the provided device " C " Set the height of the guard 3-4mm above the workpiece and lock it into position. When work is done, lower the guard to board level. (Fig.5)

３２

Fig.6 Use the provided push stick " A " to work in complete safety. (Fig. 6) a ) Check if saw blade guard in proper position. b ) Check if work under normal lighting condition. c ) Check if mounding shaft stays under safety position cap insert in proper place.

Fig.7 Insert the goniometer to carry out graduated cuts. (Fig. 7 ) SAFETY RECOMMENDATIONS Bench saw:

Fig.8

３３

Parallel cut with 45 inclination (Fig.8) FUNCTIONS Milling machine:

B A

Fig.9

Adjust the milling spindle higher to suitable position. Install washer “A”, and then milling blade. Cap the spindle by block “B” and lock it. (Fig. 9)

SAFETY RECOMMENDATIONS Milling machine:

Fig.10 ３４

Begin work using maximum caution (Fig.10). Using the two knobs, regulate the clamps. Use of the push stick is recommended. MAINTENANCE Replacement of saw blade:

Fig.11 Adjust the saw blade to top position. Put a pole tool into the hole of table and replace saw blade. Note: Products improving all the time, design and parameter changes without prior notice. Please refer to the sample.

３５

Exploded Views TAV. 1 Complete machine Assembly

ITEM NO DESCRIPTION Q’TY

01 SAWBENCH AND MILLING BODY 1

02 PLANER THICKNESSER BODY 1

03 FRONT CONNECTED PLATE 1

04 BACK CONNECTED PLATE 1

05 CAP SCREW M8X20 6

06 SPRING WASHER 8 6

07 FLAT WASHER 8 6

08 CAP SCREW M8X20 6

09 SPRING WASHER 8 6

10 FLAT WASHER 8 6

３６

Exploded Views TAV. 2 Part of Sawbench/Moulder

-

３７

ITEM NO DESCRIPTION Q’TY ITEM

NO DESCRIPTION Q’TY

01 Sawbench and moulder body 1 33 Flat washer 5 5

02 Sawbench and moulder table 1 34 Cap screw M6x45 2

03 PHLP screw M10X70 4 35 Hex nut M6 2

04 Hex nut M10 12 36 Steel foot 4

05 Flat washer10 8 37 Hex nut M10 4

06 Double saw blade assembly 1 38 Support pole 1

07 Locking block 2 39 Hex nut M16 3

08 Cap screw M8x50 4 40 Flat washer 16 1

09 Hex locking nut M8 4 41 Side cover 1

10 Flat washer 8 4 42 Cap screw M5x8 4

11 Moulder assembly 1 43 Flat washer 5 4

12 Cap screw M8x30 4 44 Main control switch 1

13 Flat washer 8 4 45 Switch guide label 1

14 Spring washer 8 4 46 Cap screw M5x12 4

15 Fence for sawbench assembly 1 47 Cap bolt ST4X25 4

16 Locking handle assembly 2 48 Scale cover 1

17 Flat washer 6 2 49 Tilting scale 1

18 Plate 2 50 Cap screw M5x6 4

19 Cap screw M10x65 2 51 Flat screw 5 4

20 Hex nut M10 2 52 Milling blade protective cover 1

21 Bolt M8X55 4 53 Saw blade cover 1

22 Hex nut M8 4 54 Cap screw M4X8 3

23 Flat washer 8 4 55 Emergency switch box 1

24 Sliding table assembly 1 56 Cap screw M5x12 2

25 Miter gauge and alum. guide 1 57 Flat washer 5 2

26 Extension table 1 58 Emergency switch cover 1

27 Side protective cover 1 59 Cap screw M4x35 4

28 Cap screw M5x8 6 60 Label for emergency switch 1

29 Flat washer 5 6 61 Dust outlet 1

30 Upper protective cover 1 62 Cap screw M6x16 3

31 Cap screw M5x8 3

32 Cap screw M5x10 2

３８

Exploded Views TAV. 3 Double saw blade assembly

（Optional 1 According to customer’s requirement）

３９



01 Small blade stand 1 29 Hex nut M6 2

02 PHLP screw M6X10 2 30 Flat washer 6 3

03 Adjusting plate 1 31 Pin 2

04 PHLP screw M8X30 2 32 Big axle 1

05 Cap screw M5x10 4 33 Adjusting washer 1

06 Adjusting axle 1 34 Round Nut M20x1.5 1

07 ”C” ring 12 1 35 Hex bolt M10X25（left） 1

08 Little axle 1 36 Washer 10 1

09 Sleeve 2 37 Big outer plate 1

10 Cap screw M10X30 1 38 Blade Ф 250xФ30x3.2x24T 1

11 Washer 1 39 Big inner plate 1

12 Little outer plate 1 40 Big location sleeve 1

13 Small blade Ф80xФ20x3.2x2.2x8T

1 41 ”C” ring 50 1

14 Little inner plate 1 42 Washer 1

15 Small location sleeve 1 43 Blade arm 1

16 Bearing 6003-2Z/Z2 2 44 Support plate 1

17 Small staff 1 45 Riving knife 1

18 ”C” ring 35 2 46 Fixed plate 1

19 Small spindle 1 47 Cap screw M6X25 2

20 Key A5X20 1 48 Protective guard 1

21 Small vice-pulley 1 49 Big staff 1

22 Flat washer 10 1 50 Big spindle 1

23 Left thin nut M10 2 51 Key A6X20 1

24 Connected pole 1 52 Bearing 6004-2Z/Z2 2

25 Cap screw M6x20 1 53 Big vice pulley 1

26 Nut M6 1 54 Hex locking nut M10 1

27 Flat washer 6 3 55 Washer 10 1


４０



４１



01 Lock handle 1 30 Cap screw M6x10 3

02 Washer 8 1 31 Flat washer 6 3

03 Turning handle 1 32 Cap screw M5x12 1

04 Key A5X10 1 33 Hand wheel washer 1

05 Flat washer 16 1 34 Hand wheel Φ 12xΦ 160 1

06 Connected plate 1 35 ”C” ring 9 1

07 Inner sleeve 1 2 36 Small adjusting plate 1

08 Cap screw M6x12 2 37 Cap screw M5x12 2

09 Clamp plate 1 38 Lifting pole 1

10 Inner sleeve 2 1 39 Key A4X12 1

11 Cap screw M6x35 1 40 Hex locking nut M8 1

12 Gear 1 41 Flat washer 12 1

13 Rack 1 42 Flat washer 8 1

14 Hex locking nut M8 1 43 Exchange block 1

15 Pointer 1 44 Pin A10X30 1

16 Pointer sleeve 1 45 PHLP screw M5X8 1

17 Cap screw M6x30 1 46 Rack stand 1

18 Rack plate 1 47 PHLP SCREW M6X25 1

19 Cap screw M4x20 2 48 Hex nut M6 1

20 Hex nut M4 2 49 Cap screw M6x45 4

21 PHLP screw M6X25 1 50 Location nut 1

22 Hex nut M6 1 51 PHLP screw M6X10 1

23 Hex bolt M6x20 4 52 Flat washer 20 1

24 Cap screw M6x25 4 53 Lifting staff 1

25 Pin A6X25 4 54 Hex bolt M10x40 1

26 Front turning block 1 55 Flat washer 10 3

27 Back turning block 1 56 Hex nut M10 1

28 Hex bolt M6x12 2 57 Shifter bar 1

29 Dust collecting cover 1 58 Inner location sleeve 1

４２



59 Cap screw M10x60 1 88 Motor plate 1

60 ”C” ring 26 2 89 Motor 1

61 Bearing 6000-2Z/Z2 2 90 Pulley 1 1

62 Adjusting pulley 1 91 Cap screw M6x16 1

63 Flat washer 10 1 92 Special washer 6 1

64 Hex nut M10 1 93 Hex bolt M8x20 4


66 Hex nut M10 2 95 Spring washer 8 4

68 Hex bolt M10x40 1 96 Hex nut M8 4

69 Hex nut M10 1 97 Adjusting stand 1

70 Flat washer 10 2 98 Hex bolt M8x50 1

71 Cap screw M10x80 1 99 Hex nut M8 1

72 ”C” ring 26 2 100 Hex bolt M8x25 1

73 Bearing 6000-2Z/Z2 2 101 Hex nut M8 1

74 Adjusting pulley 1 102 Cap screw M6x20 2

75 Inner location sleeve 1 103 Flat washer 6 2

76 Hex locking nut M10 1 104 Hex locking nut M6 2

77 Combined belt 1.5x25x750 1 105 Z-V belt（L=840） 1

78 Flower bolt M8X( at least)130 1 106 Angle steel assembly 1

79 Adjusting spring 1 107 Cap screw M6x12 4


81 Hex nut M10 2 109 Hex bolt M6x16 2

82 Hex bolt M8x50 1 110 Hex locking nut M6 2

83 Flat washer 8 1 111 Flat washer 6 2

84 Hex nut M8 1

85 Hex bolt M8x30 1

86 Flat washer 8 2

87 Hex nut M8 1

４３





01 Screw M5x12 1 15 Locking handle 1 02 Hand wheel washer 1 16 Cap screw M8x16 2 03 Hand wheel Φ 12xΦ125 1 17 Flat washer 8 2 04 Small clamp plate 1 18 Location stand 1 05 Cap screw M6x12 2 19 Stand block 1 06 Flat washer 6 2 20 Location pole 1 07 Worm gear axle 1 21 Little cover 1 08 Worm gear body 1 22 Cap screw M6x35 2 09 Spring pin 4X16 2 23 Flat washer 6 2 10 Key A4X12 1 24 Body assembly 1 11 Spacer 1 25 Rack plate 1 12 Bearing 51101 2 13 Support block 1 14 Hex thin nut M12 2

４４

Exploded Views TAV. 4 Moulder and shaper assemply:

４５



01 Spindle seat 1 29 Round nut M25x1.5 1

02 Hex locking nut M12 1 30 Lifting thread pole 1

03 Spindle 1 31 Gear 2

04 Bolt M5X16 3 32 Spacer 1

05 Spring cover 1 33 Bearing 51101 4

06 Bearing 6206-2Z/Z2 1 34 Sleeve B 1

07 ”C” ring 30 1 35 Small round nut M12X1.25 4

08 Spindle sleeve 1 36 Clamp block 1

09 Bearing 6205-2Z/Z2 1 37 Sleeve A 1

10 Motor plate 1 38 Cap screw M8x70 2

11 Hex screw M8x25 3 39 Washer 1

12 Flat washer 8 3 40 Spring pin 4X16 2

13 Spring washer 8 3 41 Pin 1

14 Pulley 1 1 42 Inner plate 1

15 Key C6X28 1 43 Outer plate 1

16 Washer (pulley 1) 1 44 Cap screw M6x20 2

17 Cap screw M8x20 1 45 Key A4X12 1

18 Nut 4 46 ”C” ring 9 1

19 Lifting nut 1 47 Hand wheel Φ 12xΦ 160 1

20 Long sleeve 2 48 Hand wheel washer 1

21 Hex nut M10 2 49 Screw M5x12 1

22 Flat washer 10 4 50 Locking handle 1

23 Motor 1 51 V-belt（L=670） 1

24 Pulley 2 1

25 Key C6X28 1

26 Washer (pulley 2) 1


28 Hex screw M10x100 2

４６

Exploded Views TAV. 5 Extension table（optional）



01 Support plate 2 15 Adjusting center Bolt 1 02 Knob bolt 2 16 Bearing 6001 1 03 Flat washer 6 2 17 Flat washer 6 2 04 Sliding block 2 18 Hex nut M6 1 05 Hex screw M6x16 8 19 Cap screw M6x20 4 06 Flat washer 6 8 20 Flat washer 6 8 07 Sliding staff 1 21 Extension table (total) 1 08 Cover 2 22 Combined scale（total） 1 09 Cap screw ST4X10 4 23 Fence 1 10 Cap screw M6x25 2 24 Knob bolt 1 11 Flat screw 6 2 25 Washer 6 1 12 Rubber ring 2 26 Sliding block 1 13 Inner sleeve 2 14 Arm 1

４７

Exploded Views TAV. 6 Saw plank



01 Sliding plank 1 20 Thin nut M8 1 02 Guide piece 1 21 Hex bolt M8X60 1 03 Knob bolt 2 22 Clamping plate 1 04 Flat washer 6 2 23 Knob bolt 1 05 Horizontal staff 1 24 Nut M6 1 06 Horizontal staff cap 2 25 Pin 1 07 Screw ST4X10 6 26 Handle 1 08 Fixed plate 1 27 Handle sleeve 1 09 Screw M5X12 4 28 Washer 1 10 Hex bolt M6X16 2 29 Cap screw M4X6 1 11 Flat washer 6 2 30 Flat washer 4 1 12 Screw M6X12 1 31 Plank support 1 13 Pointer block 1 32 Scale 1 14 Cap screw M5X10 1 33 Left cover I 1 15 Screw M6X10 2 34 Left cover Ⅱ 1 16 Fixing seat 1 35 Cap screw ST4X10 2 17 Adjusting wheel 1 18 Small fixing seat 1 19 Pin A6X45 1

４８

Exploded Views TAV. 7 Saw guide（optional）



01 Knob bolt 1 15 Cap screw M6X12 2

02 Horizontal bar 1 16 Washer 6 2

03 Clamp sleeve 1 17 Nut M6 2

04 Knob（M8） 1 18 Guide plate 1

05 Cap screw M5X12 2 19 Front location block 1

06 Washer 6 2 20 Back location block 1

07 Nut M5 2 21 PHLP screw M6X12 2

08 Scale 1 22 Hex nut M6 2

09 Knob screw M6X8 1 23 Hex bolt M6X30 1

10 Washer 6 1 24 Knob（M6） 1

11 Angle scale 1 25 Saw scale 1

12 Angle scale seat 1 26 Vice scale pole 1

13 Guide plate 1 27 Angle scale axle 1

14 Screw M6X14 1 28 Clamp block 1

４９

５０

Documents

MCO05000%3A+Platinum+Series+10-+5+Function+Combination+Machine+w%2F+Spiral+Cutters+